Search Documents

By Janshi Sen

VERTICAL-INTENSITY magnetometers, such as the Hotchkiss Superdip and the Askania vertical field balance, are now [ ] widely used, because vertical-intensity charts give definite information for the location of upper pole, dip and strike, and approximate shape of the deposit. Again, a slow and steady increase of dip over a large area indicates a large deep-lying deposit, while a large dip limited to a small area and falling away rapidly suggests a small and shallow one. The complication comes more from the richness of the ore. A large body of lean ore near the surface might produce the same vertical-intensity chart as a rich ore at depth. This paper presents a method for calculating the maximum depth of a single-pole deposit and another for a two-pole mineral body, by utilizing data of both vertical and horizontal intensities as obtained by a Thalen-Tiberg magnetometer. As shown on the left side of Fig. 1, lean ore, rich ore and a single pole produce the same magnetic field. The depth of the pole, [ ] h, can be calculated from the following relation: [h=a=tan¢=G-F h=aXFy] where G is the vertical intensity at point A due to the pole; F, the horizontal intensity of the same; and a, the distance from the point of maximum vertical intensity or the vertical projection of the pole on the surface to the point of observation A. If an entirely covered deposit is indicated by magnetic measurements and boring cost estimated from the calculated depth is so reasonable as to encourage drilling, the ore should be struck somewhere within the limit of the calculated depth by the borehole. A number of such points as A should be taken for calculation, erratic results should be rejected and the average figure used for cost estimation.

Jan 1, 1944

By E. J. Magri

Consideration is given to the problem of the estimation, from limited data, of the likely grade and tonnage for a new mining property that is to be exploited by the selective mining of two metals that have substantial contributions to make to the total revenue. In particular, the case of a new gold and uranium mine in South Africa is analysed as follows. (I) The applicability of the underlying lognormal bivariate model for different support (i.e. ore unit) sizes is examined. (2) The necessary parameters for the bivariate lognormal models for different block sizes are estimated from abundant chipsampling data from a section of the Hartebeestfontein Gold Mine using alternative approaches, and the results are compared. (3) A method is given for obtaining the necessary parameters for a tonnage-grade relationship relative to a joint pay limit from the very limited information likely to be available at the end of the exploration stage of a gold mine, and the results are compared with those obtained from the large volume of data available from a minedout area.

Jan 1, 1982

By William W. Edgerton

The California Department of Transportation (Caltrans), the Contra Costa Transportation Authority (CCTA), and the Alameda County Congestion Management Agency (Alameda CMA) are involved in a unique partnership on the planning and design of the fourth bore of the Caldecott Tunnel, located on State Route 24 in Alameda and Contra Costa counties. The project will add a two-lane bore north of the existing three bores. The project will alleviate traffic congestion in the non-peak direction. This paper provides background on the existing facility, summarizes the need for the new fourth bore, describes the proposed improvements, sets forth the approach for project delivery, and lists some of the challenges that are expected during construction.

Jan 1, 2008

Judicious placement of a range of geotechnical instruments was employed at the Tasmania gold mine, Beaconsfield, Tasmania, as a key strategy in the monitoring of rock mass conditions over the past four years. The range of instruments employed included vibrating wire stress-meters and hollow inclusion cells to monitor changing stress conditions, resistance wire and multipoint borehole extensometers to monitor the impact of stress changes on the integrity of the rock mass, and instrumented cable bolts and threadbar bolts to monitor the static and dynamic impact of rock mass changes on the installed ground control system. Initially the monitoring was of a qualitative nature, monitoring change from the time of installation. The value of the output was considerable when considered in relation to the ongoing seismic record which was also being monitored. It was clear from the seismic record and the monitoring results that stope blasting was the primary trigger for changing rock mass conditions. However, it was unclear how well observed behaviour was reflecting conditions anticipated by elastic numerical modelling. The latter had predicted significant stress increase in the near field of man-access footwall development. Qualitative monitoring and visual inspection did not support the modelling prediction, and this led to a program of quantitative measurement being undertaken. Measurement of the absolute stress condition in the backs of footwall development immediately adjacent to monitoring hollow inclusion cells provided the benchmark for tracking quantitative stress change. The program provided insight into the evolution of principal stress field magnitude and orientation in relation to rock mass change observed with extensometers and instrumented ground control elements, as well as providing a degree of calibration between the elastic numerical modelling and the virgin stress field. Calibrated monitoring data has also provided a useful benchmark for finite element modelling which is to be used for future mine-wide design.

Nov 25, 2010

By Andre C. Zingano

It is a very difficult task to estimate the immediate roof and support behavior in a room-and-pillar mining section in the initial phase of the mining project. There is little information available at this phase, and it is restricted to geomechanic characterization of the rock layers from cores samples, and the in-situ instrumentation of experimental entries and intersections. Even being a pilot excavation for roof support test a good indicator for the behavior of the immediate roof, its behavior for a full excavation mining section is different from a single intersection of two entries, mainly because the stress redistribution caused by the multiple entries excavation and face advance for a full excavation section. The objective of this paper was to calibrate a 3-D numerical model of an experimental intersection, based on the in-situ instrumentation of an experimental intersection excavation, and the geomechanic description of the rock layers. The numerical model was built with the same specifications as the excavation test, including the entry geometry and roof support. The numerical model calibration was based on wire extensometers that were installed at different positions in the roof of the pilot excavation, and on the geomechanic characterization of the rock layers that form the roof, coal seam, and floor. Therefore, it is possible to estimate whether the roof support specification adopted in the test phase will be good enough for the development of the entire mining section.

Jan 1, 2009

By Keith A. Heasley

The LaModel program has been used successfully in the United States for many years to design pillars to ensure global stability of pillar recovery operations. However, the recent Crandall Canyon Mine collapse showed that further research was required to improve the design of pillar recovery under deep cover. Toward this end, a new calibration procedure was implemented in LaModel. This calibration procedure prescribes techniques for calibrating the critical LaModel input parameters based on empirical abutment loading and pillar strength, as utilized in the time-tested ALPS and ARMPS programs. The calibration procedure is intended to help guide a novice modeler in choosing calibrated input parameters that produce a standard model that fits within the verification database. However, the rigid parameter specification incorporated in the calibration procedure also removes most of the flexibility in LaModel for specific calibration to the unique conditions at a given mine site. In this paper, a number of the LaModel input parameters are varied outside the bounds of the suggested calibration and the effects on the model results are analyzed. Ultimately, it is shown how the LaModel user might vary certain input parameters to adjust the model to site-specific conditions, while still maintaining the general accuracy and philosophy of the recommended calibration.

Jan 1, 2012

By Cristian Rodriguez, Tom BoBo, Maria Rocha, John Kemeny

Blast fragmentation depends on many factors. First of all, it depends on the specific blast design, which includes the amount and type of explosive, the blasting pattern, the timing and sequencing, and other parameters. Secondly, it depends on the properties of the rock mass, including the uniaxial compressive strength (UCS), the rock mass elastic modulus (E), the rock discontinuity characteristics (as reflected in the GSI or RMR), and the rock density. Several fragmentation models have been proposed to predict blast fragmentation based on the blast design and the properties of the rock. These models include the Kuz-Ram model and variations of this model, as well as recent models by Kim and Kemeny (2011) and others. Fragmentation models are validated and calibrated by comparing the predicted fragmentation with actual post-blast fragmentation from image processing monitoring systems.

Jan 1, 2014

A calibration of the Frantz isodynamic magnetic separator relates the current in the electromagnet and the transverse slope of the chute to the specific susceptibility at which separation is being effected. In addition to providing a rapid measure of the specific susceptibility of minerals and composite grains, the calibration provides a guide to operation of the Frantz isodynamic separator for mineral separation, and to the nature of composite grains. The most sensitive magnetic separation is obtained by using the highest practicable current and transverse slope, and the lowest practicable longitudinal slope.INTRODUCTIONProbably all minerals have a magnetic susceptibility measurable by sensitive techniques. However, magnetic separation between minerals which have low but different specific susceptibilities, and which for many purposes are considered essentially non-magnetic, has only become practicable with the development of the Frantz isodynamic separator.The construction and principle of this highly sensitive separator has been described by S. G. Frantz as an appendix to a description by 'Gaudin and Spedden (1943) of its application to the separation of sulphides constituting mill products.Various publications (e.g. Hess, 1949, Hutton, 1952) refer to its use in separating the mineral constituents of rocks, ores, and unconsolidated sands.As used in this study the Frantz isodynamic separator consists of a vibrating chute mounted centrally between the pole pieces of an electromagnet (Fig. 1). This unit may be inclined in any direction by the universal mounting, and the electromagnet current is continuously adjustable from 0 to 1·5 amperes.

Jan 1, 1957

By A. Uribe-Salas, J. A. Finch, B. J. Huls

Froth depth or interface level is an important control variable in column flotation which can influence both grade and recovery. A common method of locating the level is based on sensing the hydrostatic pressure at one or more points along the column. The level position is then calculated from these pressure readings using an equation which includes the bulk density in the froth and bubbling zones. The precision with which the level is detected depends on how well these density values represent both zones. The calculation of these bulk densities from theoretical considerations is not possible and, therefore, the practice is to estimate them by calibration. Unfortunately, the calibration parameters often do not report the level with an acceptable accuracy. A portable conductivity probe has been developed to detect the position of the interface from conductance measurements across the interface. The location of the interface corresponds to the position where a large change in conductance is observed, which is primarily a consequence of the difference in gas holdup between the bubbling and froth zones. This probe can be used to detect the position of the interface to an accuracy of± 5 cm. The probe can be used while the column is in operation, which allows the on-line calibration of the level detection system. Results obtained in its application in a pilot-scale column (0.91 min diameter) are described.

Jan 1, 1989

By Jim Lauder, Russ Calow, Ken Maley, Michael Ounpuu, Stuart T. Caverly

"Stuart T. Caverly, Section Head XRF Laboratory, Jim Lauder, Systems Engineer, Russ Stuart T. Caverly, Section Head XRF Laboratory, Jim Lauder, Systems Engineer, Russ Concession Street, Lakefield, Ontario KOL 2HOAbstractOn-stream X-ray analyzers have become an integral part of modem milling operations. The calibration of these instruments is not difficult but must be performed carefully and with consideration for the principles of X-ray spectrometry. A discussion of successful calibration procedures as well as examples of several common mistakes is presented.IntroductionOn-stream X-ray analyzers (OSA) have become an integral part of modem mineral dressing plants. Advances in instrumentation and computer software make the analysis of process streams fast, accurate and precise. Proper instrument calibration that respects the fundamentals of X-ray spectrometry is essential if the data generated are to be reliable. Often the importance of this task is underestimated and delegated to a person with inadequate XRF training. Successful OSA calibration is the result of careful, systematic procedures.On-stream analysis is perhaps the most important tool that has been provided for the concentrator metallurgist. Combined with powerful, low cost PC's and distributed control systems, real-time elemental analysis affords today's metallurgist many opportunities to troubleshoot and optimize his process.Before OSA, operators had to be very experienced if they were to achieve good results. Even with hourly grab samples, most changes in control approach would still be based on visual cues from the circuit and gut instinct. Real-time analyses have changed that completely.The last two decades have seen a persistent drive to reduce production costs. Operations utilizing OSA have been the most successful in this endeavor. Direct benefits from the application of OSA are fairly obvious. Operators are able to make incremental changes in operational parameters (e.g. reagent addition, pH, cell level), and immediately monitor the effects. Variations in the characteristics of the mill feed can be identified and addressed immediately. More progressive operations have linked analyses to control loops to adjust process setpoints ( e.g. reagent additions), and to change them automatically according to formulas based on previous experience."

Jan 1, 1996

By Carrie Pourvahidi

The California High Speed Rail Authority (Authority) was created by the State of California through legislation in 1996. The purpose of the Authority is to plan, construct, finance and operate a statewide intercity high speed passenger rail system. In 2004 the Authority prepared a programmatic level environmental document in compliance with the California Environmental Quality and National Environmental Protection Acts (CEQA and NEPA).The Authority and Federal Railroad Administration (FRA) were the lead agencies overseeing the development of the environmental documentation. The resulting document includes two volumes and 64 supplemental technical reports analyzing the transportation needs for California and the selection of an approach to meeting the project transportation needs. The Programmatic Environmental Impact Report and Environmental Impact Statement (EIR/EIS) identified High Speed Rail as the most environ-mentally protective, sustainable and economical approach to meeting the state?s projected transportation needs.

Jan 1, 2008

By W. A. Doble

Opinions differ as to whether the water-wheel almost universally known as the Pelton type belongs to the impulse, the tangential, the reactive, the jet or the percussion class, or to a cross between two or more of these classes. The fact is, that for an almost infinitesimal part of a second the axis of the jet of water strikes the bucket of this wheel at a true tangent to its base-line. The percussion of the water, striking the bucket, imparts an impulse to the wheel, causing rotation; and generally the bucket is so shaped that the direction of the jet is

Jan 1, 1900

By Brian Maroney

In this paper an overview of the California Department of Transportation's (CALTRANS) bridge design criteria is presented. Special emphasis is focused upon seismic design and retrofit criteria. Topics include earthquake load definitions, foundation and structure type selection, structural earthquake analysis, and structure behavioral requirements.

Jan 1, 1993

Jan 1, 1993

By D. Zhou, T. Hamano, Tsukihashi. F., W. -G. Seo

The thermodynamic properties for the CaO-CaF2and CaO-BaO systems were calculated by molecular dynamics (MD) simulation using Born-Mayer-Huggins type pair potential. The parameters of interatomic potential were obtained by fitting the thermodynamics properties of CaO, CaF2and BaO with the experimental data. The phase diagrams for the CaO-CaF2 and CaO-BaO systems were calculated by the thermodynamic properties obtained by MD simulation. The eutectic composition and temperature of the CaO-CaF2system calculated by MD simulation were about 28 mole per cent CaO and 1575K, respectively. The calculated eutectic point agrees very well with experimental data, which are about 22 mole per cent CaO and 1633K, respectively. Keywords: molecular dynamics simulation, thermodynamics, phase diagram, calcium oxide, calcium fluoride, barium oxide.

Jan 1, 2004

By A. H. Winckers

"CAMIRO, The Canadian Mining Industry Research Organization, formerly known as MITEC, is a collaborative research organization of Canadian Mining Companies. It is comprised of Exploration, Metallurgical Processing and Mining Divisions.The Metallurgical Processing Division (MPD) has the mandate to contribute to the profitability, competitiveness, safety and growth of the Canadian mining industry by improving the efficiency and effectiveness of mineral processing and extractive metallurgy in an environmentally conscious manner through the development of innovative technology by managing cooperative industry focused research programs.Current membership includes about ten Canadian mining companies. Past research has largely focused on base metal mineral processing. The Division wants to expand its research base to include all areas of mineral processing and extractive metallurgy.Past performance and plans for the future will be highlighted in the presentation."

Jan 1, 1998

The University of New South Wales (UNSW Australia) has been a world leader in the development of innovative virtual reality technologies over the last 15 years. AVIE (Advanced Visualisation and Interactive Environment) was developed by iCinema as a collaborative venture between UNSW?s Faculties of Engineering and the College of Fine Arts. This is the world?s first 360°-surround, virtual reality (VR) stereo projection theatre system. The School of Mining Engineering at UNSW Australia has developed 18 different virtual reality modules aimed at mine safety training and mining engineering education. These modules are being regularly used in both the mining industry and the university. The School of Mining Engineering is continuously involved in the development of different modules. Research is also currently being conducted on the implementation of other technologies into this environment. Artificial intelligence (AI) and fuzzy logic are tools that the authors would like to consider implementing in future module development. This paper will review current research in both these areas and consider options for applying these technologies.

Jan 1, 2014

By Grainne A. Matthews

Jan 1, 2009

By K. Nielsen, J. Kristiansen

A series of laboratory blasting and grinding tests on three types of hard and competent rock (coarse-grained monzonite, fine-grained granite and very fine-grained gabbro) showed that a higher level of applied explosive energy enhanced grindability and produced a larger amount of fine (-0.106 mm) material. This confirmed reported industrial experience and the results of previous investigations. However, the results did not provide any information on the quantitative relationship between the energy applied in primary blasting and that required in subsequent comminution. Only about 1% of energy consumed in conventional grinding is used to create new surfaces, while power efficencies in cone crushers have been estimated at 70-80%. In blasting, up to 20% of explosive energy may be transmitted to the surrounding rock as elastic strain energy, leading to both primary rock breakage and the generation of microcracks

Dec 1, 1995

By R. C. D. Phillis

The management of critical resource inventories is an important productivity lever and a significant risk factor?risk in the sense that poor resource availability lends itself to disempowerment of workers, unsafe work practices, wasted spending (high unit costs),and poor quality of work (including mining waste/rework). Most underground platinum mines experience lost blasts that directly lead to reduced productivity. In most surveyed shafts, 30% of lost blasts can be attributed to shortages of critical material and/or equipment. The problem is prevalent despite the existence of conventional transitory surface and underground stores. This paper discusses the introduction of buffer stores as a complementary materials storage system in order to improve health and safety in mines as well as reduce lost blasts. Both quantitative and qualitative results have shown that buffer stores result in dramatic improvements in productivity and are readily acceptable by stakeholders. Keywords Buffer stores, lost blast.

Jan 1, 2011