Search Documents

By T. Gleason

Problems involved in applying wet scrubbers to gas cleaning coal dust from thermal dryers are reviewed. Careful consideration of all the elements going into a modem coal preparation plant is required in view of the increasing difficulty of applying suitable gas cleaning equipment. This problem arises not only from the presence of finer coals to be handled, but also from the pressures applied by both the general population and the plant operators to improve the standard of gas cleaning performance. The Peabody scrubber is presented by the author as a machine designed to help improve this cleaning operation. Wet scrubbing of fine coal from thermal dryers poses a number of problems in adapting the gas cleaning equipment to the fine particulate matter. Among them are: 1) Dust in gases leaving the thermal dryer cyclones is often extremely fine with high percentages of total dust loading less than 1p in size. 2) Flue gas entering the scrubber is corrosive since the coal fired in the thermal dryer furnace is in the range of 0.7% by weight sulfur or higher. Therefore, comparatively high cost stainless steel alloys or corrosion resistant linings are required for a satisfactory service life. 3) Requirements for residual coal loadings leaving the gas scrubber are continually being lowered, while modern coal preparation operation is imposing heavier burdens on the collection system through introduction into the thermal dryer system of very fine coal previously not recovered. The advent of flotation systems in increasing numbers is typical of this trend. 4) Installation of a scrubbing system on thermal dryers is made primarily to reduce air pollution and product recovery value is of little or no value. Therefore, the operating costs of gas pressure drop and water requirements must be held to a minimum. We have, then, the basic situation which calls for comparatively high cost stainless steel alloy wet scrubbers, which must be highly effective in removing coal fines particularly in the 0 to 5-p size range. Further, the standards of scrubber performance are continually being raised towards the level where gas discharged from the scrubbers must be essentially free of any coloration due to residual dust. In view of the highly refractive nature of fine coal dust, residual loadings of 0.01 grains per cu ft or less are required to provide a color free discharge gas. In the present specifications under consideration a residual coal loading of 0.05 grains per cu ft would be considered color free, since the discharge gases are saturated in the range of 150°F. The steam plume acts as a masking agent at the point of discharge, and upon dissipation of the 150° saturated vapor stream, the effluent gas stream could be essentially color free. The specification under consideration calls for residual solids loading of 0.05 or less grains per cu ft, given a coal size distribution shown in the basic data in Table I. It is noted that the dust laden coal stream has a size distribution by weight of 33% in the 2 to 5-p size range and 55% in the 0 to 2-p size range. The particle size distribution given in the specifications does not detail the percent by weight less than 1-p in size, and more important, the size distri-

Jan 1, 1963

By A. G. Gilbert

Paradoxical is the word. The coal industry, despite reach- ing a 22-year high in production (590 million tons), has been tagged as having its back to the wall vis-a-vis its valiant attempts to quench the nation's still unabated craving for coal. What must be even more reassuring to the industry, infected once with rumors of a uranium takeover, is a nation's almost insatiable appetite for electricity. Between 1967 and the summer of 1970, utility stockpiles were being gobbled up, diminishing to 79% of the January 1968 level.

Jan 1, 1971

Continued market pressure on the US coal industry was the overriding factor affecting developments in underground mining in 1986. An oversupply of coal in the spot market kept prices low throughout the year and caused a number of operations to close their doors. Operators stepped up their efforts to improve productivity at existing operations. They made technology advances and improved their relations with employees. A continuing market-related development during 1986 was the divesting of coal properties and operations by major oil companies, which were faced with economic pressures in both the oil and coal industries. Further increases in contract mining production resulted as some larger operators were unable to compete in a tough economic environment. Longwall mining is still seen by many as the technology that will provide the necessary productivity to remain cost-effective. But the number of active faces in the US declined in 1986, as reserves were depleted and economics forced some closures. At the first Longwall USA meeting in June, much attention was placed on improved technology, as electro-hydraulic controls for roof supports gained acceptance. Other recent developments include shearer initiation of roof supports, automatic horizon control for shearer drums, and collection and storage of machine data for predicting maintenance requirements. The government and academic communities continued their research on dust control at longwall faces. Jankowski, Kissel, and Daniel, (October 1986, Mining Engineering), gave an overview of progress in longwall dust control. And Mukherjee, Singh and Jayarman (November 1986, Mining Engineering), recommended design guidelines for improving water spray systems for dust control. Surface subsidence Increasing attention is being given to surface subsidence. This is primarily because of longwall mining and the Surface Mining Control and Reclamation Act. Improved methods of prediction of surface subsidence, especially computerized methods, are being continually developed. Mining engineering faculty at major universities such as Virginia are helping develop public policy and regulations concerning subsidence. As part of this effort, Unrug and Johnson identified major subsidence areas of Western Kentucky. Peng and Chen (February 1986, Mining Engineering), gave an overview of history and research of surface subsidence. And Elifrits and Aughenbaugh, (February 1986, Mining Engineering), discussed effects of moisture variations and overburden on subsidence. This research culminated in a Symposium on Surface Subsi¬dence at the SME 1986 Fall Meeting in St. Louis and the 2nd Workshop on Surface Subsidence at West Virginia University. Ground control in coal mining continued to be an item of major research interest. Some 30 papers were presented at the 5th International Conference on Ground Control in Mining at West Virginia University. And six sessions were related to coal mining at the 27th US Symposium on Rock Mechanics at the University of Alabama. At the 4th Annual Workshop, Generic Mineral Technology Center, Mine Systems Design and Ground Control emphasized efforts of the participating universities to improve ground control. Peng and Chiang summarized results of studying support capacity and roof behavior with longwall shield supports. And Unrug, Johnson, and Nandy analyzed the process of deterioration of shale roof in a case study of a room-and-pillar coal mine. The importance of geologic conditions in determining mining productivity is receiving increased attention in coal mine design in the US. Mullenex related, through case studies, the benefits to be derived through analyzing the depositional system of coalbeds as an integral part of mine design. Improved technology in this area was related by Lloyd, Semborski, and Stolarczyk. They discussed a case study of using radio imaging to indicate coal-seam discontinuities in advance of mining. Improved coal mining technology in general is being researched more heavily, to help improve US coal competitiveness. However, much of this research and development process has yet to be widely implemented. Equipment manufacturers are devoting more resources to development of continuous-haulage systems, mobile roof-supports, mine-monitoring systems, and predictive-maintenance systems using computers to extract machine data.

Jan 5, 1987

By M. L. Mellish

The year 1988 unexpectedly turned out to be a good year for the US coal industry. In fact, it was a third consecutive year of record coal production. Accord¬ing to preliminary Energy Information Administration data for 1988, domestic coal consumption went up 5%, or 41 Mt (45 million st), from 1987. Coal exports were up by a surprising 13.6 Mt (15 million st). In 1988, 22.7 Mt (25 million st) of coal were drawn from stockpiles for consumption. Even so, US coal production increased to 862 Mt (950 million st). That was up 28 Mt (31 million st) from 1987. While coal consumption, exports, and production were up, delivered prices for steam coal continued to slide during the year. Metallurgical coal prices, however, firmed up and showed a moderate increase. This reflected tight metallurgical coal markets at home and abroad. Coal consumption US coal consumption reached 800 Mt (882 million st), compared with 759 Mt (837 million st) in 1987. Increased metallurgical coal consumption was one factor. Most of the rise in coal consumption, however, was due to unexpectedly high electricity demand. Unseasonably hot summer weather al lowed added coal-fired electric generation to supplement the drought-related reduction in hydro-electric power supply. Electric utilities consumed 687 Mt (757 million st) of coal in 1988, 35.4 Mt (39 million st) more than in 1987. Coal-fired power plants remained the primary source of US electricity generation, providing 57% of the total in 1988. Coal consumption at coke plants increased 13%, to 38 Mt (42 million st), from the level consumed in 1987. This increase reflects the recent recovery in the iron and steel industry. Metallurgical coal consumption in 1988 could have been greater. But US coke plants reportedly reached their maximum practical production capacity. As a result, net US coke imports amounted to 1.45 Mt (1.6 million st). Despite increased industrial activities, steam coal consumption by industrial plants was up only slightly from the 1987 level, amounting to 69 Mt (76 million st) in 1988. Residential and commercial coal consumption remained virtually unchanged at 6.4 Mt (7 million st). Coal exports and imports US coal exports rebounded in 1988, reaching 86 Mt (95 million st). It was the highest level of annual US coal exports since 1982, when they reached 96 Mt (106 million st). An unusual set of factors led to an opening for US coal exporters in 1988: • a high level of industrial production in Japan and the European Economic Community, • supply disruptions due to labor problems at coal mines in Poland and Australia, • a drought-related reduction in hydro-electric power generation in Canada, requiring increased coal-fired generation, • China's problems in meeting its export commitments, and • a fall in the value of the US dollar. US metallurgical coal exports in 1988 amounted to 56 Mt (62 million st), 9.1 Mt (10 million st) more than the 1987 level. Europe, Japan, and Canada were the principal importers of US metallurgical coal in 1988. European countries, in particu¬lar, increased their take by one-third of US metallurgical coal. The labor problems in Poland and Australia contributed to these higher levels of imports. So did increases in pig iron production of 8% in Japan and 9% in the European Economic Community. US steam coal exports - including bituminous, anthracite, and lignite-increase to 30 Mt (33 million st). This was up from 25.4 Mt (28 million st) in 1987 Contributing to this overall rise were 1.8-Mt (2-million st) increase in shipments to Canada and a 2.7-Mt (3-million st) increase to Europe. Unaffected by the somewhat tighter world coal market, US coal imports showed a slight increase to 1.8 Mt (million st) in 1988. Colombia continue to be the leading exporter to the United States, followed by Canada and Venezuela. Venezuela's entry into the US market is a relatively recent one, having made its first significant shipment in the fourth quarter of 1987.

Jan 1, 1989

The State of New South Wales is highly favoured in having vast deposits of coal adjacent to and within easy reach of the coastal Ports. Not only is the quality of the fuel generally superior to any found in the other States, but it is greater in extent than in any other part of the Continent. For interesting and reliable details of the history of the discovery of coal, the geology of the coal bearing strata, analysis of the various coals and other valuable data, the readers are referred to the book recently issued by the New South Wales Government, entitled The Mineral Resources of New South Wales, by Edward F. Pittman, A.R.S.M., etc., by the direction of the Hon. T. L. Fegan, Minister for Mines. The mining community is indebted to the Minister for having had published the most valuable condensed record of the mineral resources of the State extant.For the purposes of this paper we will only give such a general description of the coal fields as will make it intelligible in connection with the subject of the coal mining in the State of New South Wales.

Jan 1, 1904

By D. Peatfield

The design and operation of coal preparation plants are governed by the inherent quality of the raw coal to be processed, market specifications and the saleable tonnage requirements. Topography influences the layout of the plant but does not affect the process design. The coal market comprises many sectors, each having specific requirements with respect to both size and quality. In turn, these have led to different levels of preparation and the development of specific types of coal preparation plant design. Developments in processing techniques and processing equipment have also influenced the design and now give the preparation engineer numerous permutations in process and equipment selection. This paper gives an overview of the coal industry in general and summarizes some of the developments in the design of plants and technical developments in the areas of dense medium processing, fine coal treatment and equipment design.

Jan 1, 2003

By Mingju Liu

China has been suffering from coal and gas outbursts since 1950s. Nowadays, the situation has become worse than ever with the need to mine deeper coal deposits at higher production rates in a more complex underground mining environment. In the year 2006 alone, 37 outbursts occurred in underground coal mines with a death toll of 232. This paper describes a case study of an outburst event, which occurred in July 2006 during the shaft development of the Mengjin Coal Mine, Henan Province, China at a depth of 768m below surface. Detailed analysis of the possible causes that led to the occurrence of the outburst is reported. These include the study of complex geological features, gas storage conditions, possible improper technical management practice as well as incomplete prevention and control measures. Based on the case study and the observation of outburst occurrence in China in the year 2007, suggestions have been put forward to help prevent and control future coal and gas outbursts.

Jan 1, 2007

By R J. Mills, B S. Sinclair, D A. Fergusson, A G. Goldstone

In 2005, Solid Energy New Zealand Limited obtained non-notified consent for the disposal of 1Mt of coal ash at the Rotowaro minesite, forming part of a coal supply agreement with the Huntly Power Station. The consenting of major mine site activities has historically required wide consultation and involves notification of the application.   The risk and cost associated with consultation can be significantly reduced via a non-notified process. A non-notified consenting process necessitates environmental effects to be shown to be æless than minorÆ, which requires the combination of robust science and a pragmatic approach to design, assessment of environmental effects, and consenting issues.   Key issues examined included consideration of how to practically operate a significant disposal project within the confines of an operating mine, minimising the costs, civil and geotechnical design and practical issues associated with traditional disposal. Environmental issues specifically related to the coal ash, led to a site specific performance driven approach to management rather than relying on conventional prescriptive approaches. Environmental issues of concern include the leaching of boron and aluminium from ash into groundwater and mine water management systems where both boron and aluminium can occur at elevated levels.   Coal ash exhibits unusual geochemical characteristics reflecting the primary coal composition and the combustion process. The dominant coal type combusted at the Huntly Power Station is derived from Rotowaro and the resulting ash is cementitious and has a high alkalinity. As a result the disposal design is based on the characteristics of the ash itself rather than the material into, or onto which the ash is disposed. Non-notified status was able to be achieved through consideration of these key characteristics of the ash, ensuring that the dimensions of the disposal site and each location was designed to minimise the flow of groundwater through the ash and demonstrating that the physical ash disposal effects are less than minor compared to the consented mining operation.

Jan 1, 2006

By S Speed, N Corlis, A Goldstone, G N. Browne, M Fitzpatrick

In 2005, Solid Energy New Zealand Limited obtained non-notified consent for the disposal of 1Mt of coal ash at the Rotowaro minesite, forming part of a coal supply agreement with the Huntly Power Station. A non-notified resource consent was sought which necessitated that environmental effects be shown to be æless than minorÆ, and resulted from robust science and a pragmatic approach to design. As part of the assessment of environmental effects, there was a need to understand the effects of boron concentrations on aquatic organisms (ie algae, plankton, plants and invertebrates) in the receiving environment. Boron is a naturally occurring element that is found in the form of borates in the oceans, sedimentary rocks, coal, shale, and in some soils but Waikato coals and ashes have particularly high boron content. Boron is an essential micronutrient for higher plants with interspecies differences in the levels required for optimum growth. As aspects of the ANZECC (2000) derived boron limits are based on toxicity of aquatic algae and plants to boron it was important to assess these components in the environment. The effects on the receiving environment of the Awaroa Stream were assessed using predicted water chemistry and comparing actual boron concentrations in a comprehensive and multifaceted reference-condition approach of catchment ecological indicators. In addition a toxicological-based assessment of boron and a re-calculation of the ANZECC trigger levels were undertaken and applied to the ecological indicators. The reference-condition approach revealed that habitat and overall water quality attributes at and between sites was more influential in determining the aquatic biotic communities than boron concentrations alone. There was no evidence of any gradient of changes in ecological indicators with changing boron concentrations, nor evidence of any residual effect of high historic boron concentrations on the aquatic biota.

Jan 1, 2006

By K. S. Lackner, T. M. Yegulalp

We present a review of research and development for coal based clean energy systems aiming for zero emissions to the atmosphere. These systems can utilize all kinds of coal or other solid carbon sources such as tar sands as well as liquid hydrocarbons. The chemical energy of carbon is transferred to hydrogen and used in power generation, in fuel cells, or hydrogen combusting turbines. The waste products of these future power-generating systems are ash, sulfur compounds and CO2. We also summarize current and developing technologies for processing of CO2to produce mineral carbonates for permanent disposal, and associated byproducts.

Jan 1, 2003

Automation in underground mining enhances safety and leads to economic efficiency. In the past many efforts have been made on the automation of longwall shearer operation. With respect to the ultimate goal of automation, ie self controlled operation, coal bed boundary detection is one of the key problems. For longwall human labor is necessary in order to detect the exact position of the coal seam to be excavated. The authors present a sensor concept based on infrared technology and pattern recognition which will solve this problem. The very harsh underground conditions set high demands on the implemented sensors. The combination of infrared sensors and powerful processing algorithms is part of the innovative concept for automation of the new Eickhoff Bergbautechnik GmbH SL 750 shearer loader. The multi-sensor automation system EiControlPlus which is designed for the complete detection of the machine environment fills in the gap in the coal-excavation automation by building a recognition system that turns the shearer loader into an 'intelligent machine' which is capable of detecting the correct position of the seam to be excavated and thus enables human-free coal mining.

Dec 6, 2010

Geological discontinues in the coalbed, such as faults, sandstone channels, permeability facies, lithotype changes, and large scale partings in the coal seam, can cause intermittent production problems or produce unexpected amounts of water or gas from degasification boreholes. These discontinuities not only can impact methane emissions into the mine workings, especially if they hinder proper and effective degasification of the coalbed but may act as conduits for methane flow from gassy strata into advancing mine workings. The effects of these discontinuities are still under debate by mining and gas production experts. This study presents a numerical investigation using reservoir simulations of the effects of partings and permeability facies and lithotype changes on the production performances of vertical and horizontal degasification boreholes, as well as the emissions during longwall operations. In this work, the grid block was designed in a multi-layer 3-D structure which enabled spatial descriptions of the geometries and properties of the discontinuities within the coal seam. The studied coal seam discontinuities and their properties were distributed arbitrarily within the model. Production was simulated by vertical and horizontal boreholes. Degasification boreholes operated two years prior to start of the mining. The results of this numerical study show that in coal seams with major heterogeneities and discontinuties, the geometry and location of the boreholes are important for improved gas production. These considerations are also important for controlling methane and water inflow into the working environment during longwall mining.

Jan 1, 2008

By Xuchen Fan, Chenyang Zhou, Yuemin Zhao, Liang Dong, Chenlong Duan

A gas–solid fluidized bed using magnetite particles is an effective methodology for coal beneficiation in the field of dry coal cleaning. Broadening the size range of magnetite used in the bed decreases medium preparation cost. In this study, a tapered fluidized bed was used to investigate a magnetite particle size range of −0.5 + 0.074 mm. The results showed that a tapered fluidized bed effectively strengthens mixing of magnetite with a wide size range (−0.5 + 0.074 mm). The results of beneficiation experiments indicated that with increasing tapered angle, separation efficiency increased and then decreased. The highest separation efficiency was obtained at a tapered angle of 10°. The optimal results showed that the ash content of the concentrate decreased from 31.82% to 12.33% with a probable error of 0.11, which indicated that a tapered fluidized bed was efficient to improve fine coal beneficiation performance.

By Jeffrey K. Whyatt

The Crandall Canyon accident investigation included an interesting and unexplained observation by rescuers that the ?barrier rib had shifted northward as a unit, as much as 10 feet.? This is not the first mention of such a movement, although such reports are rare. Historical accounts describe unusual movement and displacement of intact coal, cribs and timbers. Two movements of particular interest are the creation of gaps above coal pillars and falling of standing support elements without apparent damage. A dynamic boundary element program was used to explore movements induced by slip on geologic features removed from the affected panel. While the resulting models are much too simple to fully replicate these observations, they do show that the types of phenomena observed are possible. They can also provide insight into the types of motions that ground support elements are subjected to during large bump events. This was demonstrated for the case of a large bump in a Book Cliffs coal mine. Seismic information suggested the source mechanism to be normal slip on a fault. A model of that source showed initial dilation of the panel followed by dynamic compression and rebound ? consistent with underground observations. The initial dilation is important as it may allow slender standing support to shift or fall.

Jan 1, 2009

By Jeffrey K. Whyatt

The Crandall Canyon accident investigation included an interesting and unexplained observation by rescuers that the ?barrier rib had shifted northward as a unit, as much as 10 feet.? This is not the first mention of such a movement, although such reports are rare. Historical accounts describe unusual movement and displacement of intact coal, cribs and timbers. Two movements of particular interest are the creation of gaps above coal pillars and falling of standing support elements without apparent damage. A dynamic boundary element program was used to explore movements induced by slip on geologic features removed from the affected panel. While the resulting models are much too simple to fully replicate these observations, they do show that the types of phenomena observed are possible. They can also provide insight into the types of motions that ground support elements are subjected to during large bump events. This was demonstrated for the case of a large bump in a Book Cliffs coal mine. Seismic information suggested the source mechanism to be normal slip on a fault. A model of that source showed initial dilation of the panel followed by dynamic compression and rebound ? consistent with underground observations. The initial dilation is important as it may allow slender standing support to shift or fall.

Jan 1, 2009

By John Hoelle

Coal mines in southern West Virginia, south-western Virginia and eastern Kentucky have experienced coal bumps at least since 1933. Most of the bumps have occurred due to high cover, strong roof and floor strata and stress concentrations due to the mining sequence. A longwall mine in eastern Kentucky first experienced coal bumps on the tailgate side of the longwall face in 1989. The bumps continued until 1996. The bumps were the result of: Thick overburden up to 2200 feet Strong roof and floor (strata strengths up to 25,600 psi UCS and elasticity modulus up to 4,800,000 psi Previous over-mining in places Sandstone channels Not all characteristics occurred simultaneously. The bumps produced seismic events recorded up to 4.3 (Richter scale magnitude), and damaged pillars that were up to 147 by 152 feet in size.

Jan 1, 2008

This paper reviews the likelihood of instability occurring within coking coal cargoes from BHP CoalÆs northern Bowen Basin mines. In coal cargoes, initial moisture redistributes vertically towards the base, saturating the bottom layers unless the bilge wells are pumped regularly. There has been concern in some quarters that saturated coal in the basal layer may be prone to liquefaction, and if the vessel then rolls significantly in rough seas, overall sliding movement of the cargo might occur. However, a review of shipping accident statistics reveals that casualties relating to shifting of coal cargoes are quite rare, and have not occurred in modern large bulk carriers (>15 000 dwt). The moisture redistribution process has been analysed to quantify the extent of cargo saturation that may occur. Results indicate that the amount of redistribution increases with initial moisture content above a threshold of eight to nine per cent. However, the removal of water by pumping from the bilges is remarkably effective in reducing the extent of saturated coal (and therefore the possibility of cargo liquefaction and movement), and in controlling the average moisture content of the bottom layers of cargo. Stability analyses were then performed for deep sliding of a cargo with a saturated and liquefied base. These have confirmed that sliding of a cargo with a liquefied base during rough seas (20¦ roll angles) would require initial total moisture content exceeding 13 per cent, the hold half full or less (width/depth >3), and no bilge pumping so that height of the saturated zone is as deep as possible. Overall, the results indicate that coking coal cargoes from BHP CoalÆs northern Bowen Basin mines will be unlikely to suffer sliding or liquefaction failures when transported in modern large bulk carriers.

Jan 1, 1997

By W. A. McCurdy, Joseph W. Leonard, William F. Lawrence

INTRODUCTION Utilization from the Point of View of the Preparation Engineer The primary interest of the coal preparation engineer is in process design, operation, and maintenance to produce an acceptable product that can be sold at the greatest possible profit. Because of emphasis upon these interests, attention to other potential values of coal is sometimes neglected. The intent of this chapter is to alert the preparation engineer to the utilization possibilities of the product as well as the tributary coal flow moving through a modern coal preparation plant. The basis for any unrealized potential derives directly from the coal seam itself. Most coal seams consist of coal bands and benches sandwiched together in layers that differ visually from each other in physical structure and luster. Randomly selected physical and chemical ranges determined from layers of coal in a single seam can easily differ by as much as 30 Hardgrove grindability indices, 0.30 of a specific gravity point, 20 percentage points of ash, 6 percentage points of dry volatile matter, and 10 percentage points of total su1fur.l Similar wide variations exist for calorific value, seam moisture content, and, undoubtedly, for any other conceivable coal test parameter that might be used for comparative purposes. These observations all point to the long-established fact that coal is not homogeneous, as conventional analytical methods might tend to indicate, but is instead a highly heterogeneous substance.

Jan 1, 1979

By J. Y. Hwang

The relationship between coal characterization and physical cleaning has not been well understood due to the complex nature of coal. Therefore, it is difficult to apply the results of coal characterization to predict and evaluate the performance of a physical separation (e.g. flotation). Eight U.S. bituminous coals were analyzed and studied petrographically in conjunction with washability and flotation tests. The results show that grindability correlates to ash and fixed carbon contents; liberation determined directly by petrographic techniques is close to liberation determined indirectly by washability; and an ideal separation efficiency can be determined by measuring the inertinite content and the washability separation efficiency using a heavy liquid with a density of 1.4. The ideal separation efficiency was attained for most coals by packed column flotation. The ideal separation efficiency can be used for comparing process technologies and process parameters.

Jan 1, 1988

By A. Lloyd, Montgomery, J. Jorgesen, W. J.

"Coals are ranked according to their degree of metamorphism or progressive change in the natural series from lignite to anthracite. The reader is referred to ASTM Standard D-388, ""Standard Classification of Coals by Rank"" for a detailed description of the system in use throughout North America including Canada.Fixed carbon and calorific value (expressed in Btu/ lb) calculated to the mineral-matter-free basis have been chosen as the main characteristics from which rank is established. Higher rank coals are classified according to fixed carbon content, lower rank coals according to the calorific value on a ""moist"" mineral-matter-free basis. Certain adjacent groups are differentiated according to their agglomerating (caking) properties. ""Moist"" refers to inherent moisture. Referring to Table 1, coals having calorific values greater than 14,000 Btu/lb on a moist mineral-matter-free basis and fixed carbon of 69% or more on a dry mineral-matter-free basis are classified according to fixed carbon. Coals having calorific values of less than 14,000 Btu/lb on a moist mineralmatter-free basis are classified according to calorific value on a moist mineral-matter-free basis. Agglomerating coals having 69 to 86% fixed carbon on the dry mineral-matter-free basis are classified in the low or medium volatile group of the bituminous class according to their volatile matter content. Agglomerating coals having calorific values between 10,500 and 11,500 Btu/lb are classified in the high volatile C bituminous coal group; nonagglomerating coals in the same calorific value range are classified in the sub-bituminous A coal group."

Jan 1, 1985