Search Documents

THE Yallourn chimney has aroused interest, as it is, for the time being, the tallest structural erection in Australia. Its height was not decided on, however, with the object of breaking records, but is purely incidental to the purpose which it serves. Theboiler plant at the briquetting works (first instalment) consists of five Babcock and Wilcox land-type water-tube boilers, each of 4510 sq ft. heating su:r£ace and 225 sq. ft. grate area in the form of step grates. Four boilers will normally produce 73,000 lb. of steam per hour at a gauge pressure of 265 lb. and a temperature of 6500 F., the fifth boiler being a reserve. Each boiler will consume about 100 tons of Yallourn coal per 24 hours. Provision is made for future installation of economizers, should it be found desirable. Designing for this condition, and allowing for a waste gas temperature of 3500 F. and an air temperature exceeding 1000 it was found necessary to have a draft of about 1.3 in. (water gauge) at the base of the chimney, and to deal with about 2000 cub. ft. of gases per second. Estimates were made of the cost of providing the necessary draught by means of fans and by means of a tall chill).ney. The annual charges of the two methods differed only slightly, and the tall chimney wasselected as being the more general practice in briquetting factories.Estimates were prepared for brick and concrete chiIlllleys. Yallourn bricks at that time were hand-made, and, while very suitable for domestic work, were not capable of withstanding high compressive stresses. The chimney design to suit these bricks thus required to be on very ample lines, resulting in high cost. Machine-made bricks from Melbourne would cost about £5 10s. per thousand on the site, with extra for radials, so that high cost again resulted. On the score...

Jan 1, 1924

By Jamal Hematian

Understanding the behaviour of rocks in a high horizontal stress field, such as that in Australia, is critical when analysing the stability of underground structures. This paper addresses the significance of the post-failure behaviour of rocks on the stability of underground structures which are under the influence of a high horizontal stress field. The research work was conducted through a combination of numerical modelling, laboratory testing and field investigation. A number of 2-D FE model of roadways were constructed based on the data obtained from laboratory testing and field investigations. The models were then analysed using three different solution techniques; simple linear-elastic, non-linear elastic-plastic and elastic-plastic with consideration of post-failure behaviour (softening model). Results indicated that the post-failure behaviour of rocks significantly influence the stress and displacement patterns around the roadway. The stress and displacement patterns as well as the extent of the yield zone around the roadway predicted by the softening model were in good agreement with that from the field study. Based on the results of the study, an appropriate support system has been suggested to govern the stability of roadways.

Jan 1, 1994

By Nikolas K. Sokol

Underground construction often requires working within a very congested urban environment, including excavating shafts adjacent to highly sensitive and multistoried structures, sometimes even within such structures. Shafts adjacent to heavily loaded column footings are often required due to space constraints. Invariably, footing surcharges must be considered during the design of shaft rock reinforcement. Rockwedge stability evaluation reveals that column surcharges can greatly impact the ability to meet the desired factor of safety. Design methodologies and examples to deal with these special circumstances are presented.

Jan 1, 2008

By Christopher Mark

Roof bolt system design means the selection of the type, length, capacity, and pattern of bolts for a particular application. Despite research efforts dating back 50 years, no design methodology has found wide acceptance. This paper begins by identifying four mechanisms that roof bolts use to reinforce the ground. It argues that the reinforcement mechanism is determined by the roof geology and stress level, not by the type of bolt. Next, the attributes of roof bolts are discussed in the light of recent research, including anchorage mechanism, installed tension, length, capacity, timing of installation, and installation quality. Several significant areas of controversy are identified. Design methods from around the world are discussed, including those based on empirical research, numerical modeling, and roof monitoring. Finally, some simple guidelines for preliminary design of roof bolt systems are proposed based on statistical analysis of roof support performance at 37 U.S. mines.

Jan 10, 2000

By Frank P. Frandina, Diane R. Hirsch, David P. Field, Colin R. Weeks

To accommodate growth in air service and to follow the Master Plan for long-term airport development, the Metropolitan Washington Airports Authority established thed2 Development Program at Washington Dulles International Airport. A sub-surface Automated People Mover (APM) System is under construction to replace the Mobile Lounges as the primary people mover system at Dulles. To minimize disruption to airport operations the majority of the APM System’s crossings of Taxi lanes will be undertaken using Tunnel Boring Machines (TBM) or the New Austrian Tunneling Method (NATM). This paper explores the planning and design of these shallow tunnel segments for future generation aircraft loads, within the constraints of minimal construction access under post 9/11 security requirements and the context of the overall airport expansion program.

Jan 1, 2005

By Jan Pru?ka

This paper describes the sheet pile design for the Line C extension from Ládví station to the North of Prague. The first part of the paper describes the geological conditions and structural configuration of the project. Typical cross sections, the description of the construction stages, and monitoring are discussed. The second part of the paper focuses on the sheeting design method. It describes the method of dependent pressures, that is, how the pressures acting upon a structure depend on the deformation. The design process and verification methodology are described in detail with comparison of the results with in-situ monitoring.

Jan 1, 2011

By N. Katsikaros, N. S. ‘ Yap, B. Adaszynski

"Cyanide is a well proven, effective lixiviant that has been utilised for centuries in gold extraction processes. Despite being used in close to 90% of gold processing plants, cyanide leaching is still being scrutinised due to its toxic nature. With governments tightening the regulations on cyanide management, and recently erected sites situated closer to community and environment, leach waste and tailings treatment has become increasingly important. Gekko Systems has worked with engineering companies and directly with gold producers to provide technical services and supply complete modular cyanide destruction (detox) systems for plants leaching both run-of-mine ore and high sulphide gravity and flotation concentrates. Although similar in principle, the different materials presented unique challenges in design and implementation. Similar to designing any section of a processing plant, the development of the cyanide destruction plant design began with laboratory test work to simulate the full scale operation. This paper focusses on the laboratory test work and how other critical factors such as geographical location, logistics, and local community play a role in the process design and construction. Two design and supply cases are discussed in this paper; one treating intensive cyanidation concentrate leach tails and one treating whole ore CIL tails. Although these plants both use the SO2/O2 process, each presented different challenges in laboratory testing and plant design, resulting in variations in final implementation including reagent choice, oxygen supply, and process control.INTRODUCTIONSince 1887, cyanide has played a large part in the beneficiation of gold from gold bearing ores. Cyanide is used to solubilise gold into solution, and is typically added in excess to maintain the leaching process. Some or all the excess cyanide can often be recovered and reused in the process however chemical destruction of cyanide is often necessary to manage cyanide levels in the tailings storage facility (TSF)."

Jan 1, 2016

By M. N. H. Khan

CSIRO has been experimenting with supersonic flows as a method of rapidly quenching metallic vapours. Cooling rates above 106 °C/s have been achieved. The supersonic flow conditions are achieved by adiabatic expansion of the vapour through a Laval nozzle into a vacuum chamber. This paper will describe the basic physics of the process, outlining computer fluid dynamic (CFD) modelling of flow in the nozzle, the effects of different flow conditions on the condensation process and discuss the practical design issues associated with operating supersonic nozzles. Results obtained from a CFD model of the nozzle, which compared two methods of incorporating condensation, showed that inclusion of condensation substantially changes the conditions in the nozzle. Most noticeably, the effect of condensation produces a region in the nozzle where the temperature remains almost constant.

Jan 1, 2006

By Kenneth Pidgeon

The Boston Marine Industrial Park (BMIP) Boat Section, which is part of contract C04A2 of the Central Artery/Tunnel (CA/T) project, is currently under construction in South Boston, Massachusetts (Fig. 1). The Boat Section is approximately 900 feet long and varies in width from about 135 to 185 feet (Fig. 2). The depth to the top of the Boat Section base slab varies from about 28 to 31 feet below final ground surface and about 23 to 26 feet below normal ground water levels. The Boat Section is supported on 578 anchors drilled into the underlying bedrock each designed for a working load of 630 kips. Design and Construction Team The owner of the project is the Massachusetts Highway Department (MHD). The owner's representative is the Management Consultant, Bechtel/Parsons Brinckerhoff. The section design consultant (SDC) consisted of HDR Engineering, Inc. with GEI Consultants, Inc. as the geotechnical subconsultant. The general contractor was the joint venture of Kiewit, Perini, Atkinson, and Cashman. The boat anchors were installed by the subcontractor Delta Geotechnical Services, Inc.

Jan 1, 1994

By Leon Maday, Dan L. Pecha, Jeremy Johnson, Daniel N. Adams

The Brightwater conveyance system includes 26 km of tunnels, a 130 mgd pump station, 2 km of micro tunnels, and a 2.4 km outfall. The tunnels extend from Woodinville to Puget Sound through varying soils in 1 to 7 bars of hydrostatic pressure and depths to 185 m. The tunnel diameters range from 4 to 6 m and include numerous lining systems. This paper highlights major shaft and tunnel design, including dual cellshafts, multiple pipe configuration tunnels, polymer concrete segments, and the use of a one pass lining designed to convey high pressure effluent.

Jan 1, 2005

By Liang Shen

The Cooper River Bridge, the longest cable-stayed bridge in North America, replaces two existing bridges along U.S. Highway 17 and connects the City of Charleston and the town of Mount Pleasant, South Carolina. Two diamond shaped towers support the 1,546 ft long main span over Cooper River and allows for a 1000 ft wide navigation channel. The Charleston high-level approach is 4351 ft long and provides a 250 ft wide navigation channel for Town Creek, while the Mount Pleasant high-level approach is 2,090 ft long. Due to the high seismicity in the region, potential vessel impact, and hurricanes, large lateral loads are expected. From various types of foundations, 10-foot diameter drilled shafts were selected for their high capacity against vertical and lateral loadings. The shafts are founded on a stiff to very stiff lightly cemented calcareous sandy clay or sandy silt layer, called Cooper Marl, which underlies the coastal sediments of the interbedded clays and sands. A group of 11 shafts supports each main tower, while a rock island protects it from vessel collision. A group of 4 to 8 shafts foundations support the other piers of the main span unit. A pair of shafts supports the High Level Approach piers. The shaft tip elevations vary from 120 ft to 230 ft below water line. An elaborate geotechnical investigation was conducted on the site, including a load test program on full-scale shafts under axial and lateral loads. The results of the tests were used to calibrate the lateral and axial soil resistance. The objective of this paper is to present the different aspects of the bridge foundation design.

Jan 1, 2013

By Jim Rozek, Robert A. Gee

The Epping to Chatswood Rail Line project is the largest publicly funded infrastructure project in New South Wales. Construction commenced in November2002 with opening scheduled for 2008. The work includes 13 route km of twin TBM driven 7.2 m diameter lined running tunnel, three cross-overs and three new underground stations. The new stations have platform caverns of 20m span with similarly proportioned concourse caverns alongside. The ground is bedded sand stone and shale with high horizontal stresses. Predicted stress-relief induced ground movements during staged excavation led to innovative use of rock anchors for permanent support.

Jan 1, 2005

By A. F. Deng

A general description of the project, mainly the pier foundation design of the ZHU JIANG FANYING is presented in the paper. The major contents include the foundation scheme, the evaluation of bed-rock characteristics, the allowable bearing pressure, the design and construction of pier foundation.

Jan 1, 2010

By Philip K. Chan

Batu Hijau is a new copper and gold mine located on the island of Sumbawa in the Republic of Indonesia. This paper details the design and construction of the Batu Hijau overland conveyor, one of the most challenging efforts of the project. The 1.8 m wide, 5.6 km long conveyor has a design capacity of over 10,000 mtph and carries primary crushed ore through the steep mountains of Sumbawa, which necessitated a 160 m vertical downhill section, a 75 m vertical uphill section, ten vertical curves and one horizontal curve.

Jan 1, 2000

By Graham Holmes, John Starkey

"The Kinross Kubaka Project is a gold mine located in the Russian Far East. The grinding circuit, comprised of a 6.1 m diameter x 2.74 m long SAG mill and a 4.1 m diameter x 5.5 m long secondary ball mill in closed circuit with cyclones, was built using SAG Power Index and Bond Ball Mill Work Index testing to determine the grinding energy requirements. Extremely cold climatic conditions and the need to keep heated space and capital costs to a minimum, dictated a grinding circuit with no in-circuit crusher and no conveyors external to the mill. High energy requirements for both the SAG mill and the ball mill were correctly predicted and have allowed grinding production tonnage forecasts to be met. Design test data and production results are given.INTRODUCTIONIn 1995 Davy International Canada, now Kvaerner Metals E & C, was commissioned as the Engineer and Project Manager for the Omolon Gold Mining Company, to design and construct a gold extraction plant for the Kubaka gold deposit, located in the Russian Far East. This deposit had been studied extensively in Russia during the exploration phase and a Feasibility Study was completed in 1993 by Kilborn who visited the site twice during that year to inspect facilities and to take metallurgical test samples. More samples were taken in 1995 to check ore hardness variability, as part of the final design program by Davy.The client’s objective in designing the Kubaka grinding circuit was to achieve design tonnage at all times, even when milling the hardest ore zones in the deposit. Since the samples taken in 1993 were taken as composite samples, it was necessary to take additional samples in 1995 to determine the extent of the variability. Six samples were sent to Canada for SAG Power Index (SPI) testing. Five of these were combined as a composite open pit sample, while the sixth sample was taken from the site adits as a composite sample to represent undergound ore. These two composite samples were tested to determine the MacPherson Autogenous Work Index for comparison with the SPI values."

Jan 1, 2001

By Gerry Houlahan

The east span of the 3.5 km long SF-Oakland Bay Bridge is supported by different types of foundations along its span. Starting from the west, its first 460 m section comprising twin concrete box-girders is supported by sands and rock on Yerba Buena Island. A 620 m long steel suspension span then bridges a 25 m deep channel that is formed in sediments overlying rock. Twin concrete box girder structures, each 2.4 km long, complete the stretch over the remainder of San Francisco Bay to the engineered earth fill landing at its east end. For most of its length, the Skyway bridges water 3 to 10 m deep over soft surficial Young Bay Mud. The foundation types include spread footings with hold-downs, steel and concrete piles that are set in drilled rock sockets up to 3 m in diameter and 2.5 m diameter steel tubular piles driven to penetrations of up to 100 m. The design and construction-related considerations are presented. The different foundation types, influences of the site geology and earthquake demands on the substructures are discussed. The seismic motions of the bridge superstructures and substructures, as well as the depth-varying soil motions, influenced the foundation design. Together with performance-based design criteria, including post-earthquake footing displacement limits, these seismic demands influenced various aspects of the foundation design, including the use of battered and vertical piles.

Jan 1, 2005

By P. Mark. Hawley

Development of Barrick Gold?s Pierina Gold Mine in north-central Peru requires construction of a waste dump for disposal of non-ore grade materials stripped from the open pit to expose the ore. The waste dump site is located near the open pit in a U-shaped valley that is underlain by thin colluvial and morainal soils with locally thick peats and glaciolacustrine deposits. Bedrock underlying the site consists of variably weathered volcanics. The site is subject to moderately high seasonal rainfall and significant seismicity. The geotechnical quality of the waste rock is highly variable, ranging from low quality, degradable, soil-like materials containing appreciable quantities of silt and clay, to high quality, hard, durable, blocky waste rock. A hybrid dump design concept was developed that requires in-pit segregation of high and low quality waste, and selective placement of materials in the dump to maximize stability and enhance internal and subsurface drainage. The design includes a rock drain beneath the dump along the axis of the valley and a series of connected finger drains. Extensive peripheral diversions and stormwater control measures to inhibit infiltration of precipitation are also included. This paper discusses the unique challenges presented by the site and waste materials, the design methodology and stability analyses, and planned monitoring systems.

May 1, 2002

By R. Sharon, P. M. Hawley, X. Ochoa

"Development of Barrick Gold’s Pierina gold mine in north-central Peru requires construction of a waste dump for disposal of nonore grade materials stripped from the open pit to expose the ore. The waste dump site is located near the open pit in a U-shaped valley that is underlain by thin colluvial and morainal soils with locally thick peats and glaciolacustrine deposits. Bedrock underlying the site consists of variably weathered volcanics. The site is subject to moderately high seasonal rainfall and significant seismicity. The geotechnical quality of the waste rock is highly variable, ranging from low-quality, degradable, soil-like materials containing appreciable quantities of silt and clay, to high-quality, hard, durable, blocky waste rock.A hybrid dump design concept was developed that requires in-pit segregation of highand low-quality waste, and selective placement of materials in the dump to maximize stability and enhance internal and subsurface drainage. The design includes a rock drain beneath the dump along the axis of the valley and a series of connected finger drains. Extensive peripheral diversions and stormwater control measures to inhibit infiltration of precipitation are also included.This paper discusses the unique challenges presented by the site and waste materials, the design methodology and stability analyses, and planned monitoring systems."

Jan 1, 2003

The pressure of low commodity prices forced the design process for the second lift of Northparkes E26 Mine to adopt a continuous improvement philosophy. The emphasis was to minimise capital expenditure while still maintaining the excellent low operating costs achieved on Lift 1. Although the first block cave lift at Northparkes is the most productive underground mine in the world and is held up as a benchmark for the use of technology in mining, areas for improvement were identified. Every area was critically assessed and investigated for the possible application of new techniques and technologies. Key learnings from the construction and production phases of Lift 1 were captured, documented and used as the starting point for the Lift 2 design. This paper shows how and why the design parameters initially used onLift 1 were changed to become the current E26 Lift 2 developmentproposal. The main differences between the two block caves arehighlighted. The alternative techniques and equipment that wereconsidered are also discussed. * Originally published in the Proceedings of MassMin 2000,published by The AusIMM.

Jan 1, 2001

By Daniel N. Adams

The University Link project extends Seattle?s light rail from downtown to University of Washington (UW). It includes 5.0 kilometers (3.15 miles) of twin-bored, 6.4 meters (21 feet) excavated diameter tunnels, and two cut-and-cover stations. The Capitol Hill Station (CHS) requires an excavation 170.7 meters (560 feet) long, 22.6 meters (74 feet) wide, and 22.9 meters (75 feet) deep. The University of Washington Station (UWS) requires an excavation of about 238.4 meters (782 feet) long, 21.3 meters (70 feet) wide, and 33.5 meters (110 feet) deep. The project is within the glacially diverse soils of the Puget Sound region, below groundwater. This paper highlights major station and tunnel design elements, including the approach to support of excavation at both station boxes, and the site staging requirements.

Jan 1, 2008