Search Documents

By Alf Hartling

"Most of the Paleozoic section of the Williston Basin is a thick accumulation of numerous carbonate to evaporite, shallowing upward, cyclic sequences. These sediments were deposited in broad epeiric seas, and the deposition of the evaporite facies marked the final stage of each cycle. Many of the sequences display a pervasive replacement dolomite in the uppermost portion of the carbonate units. This secondary dolomitization is, at least in part, an early diagenetic event, synchronous with evaporite deposition.The inception of evaporite precipitation resulted in the seepage of a dense, Mg-rich brine into the underlying sediment. The heavy brine moved down the gentle regional dip displacing the more normal marine interstitial pore fluid and dotomitized the primary calcitic sediments en route. The supply of Mg-ions decreased away from the source, and correspondingly, the degree of dolomitization decreased and larger crystals formed because of slower nucleation at fewer sites.The seepage refluxion of dolomitizing brines gave rise to the frequently observed textural variation of cryptocrys talline, impervious dolomite grading into a finely sucrosic, permeable dolomite down-dip. This diagenetic facies change provides the critical up-dip barrier for potential hydrocarbon reservoirs. The lateral pool boundaries are controlled by either structural relief or a similar diagenetic facies change. The reservoirs are capped by the tight evaporites.Hydrocarbon production is attained from diagenetic traps in the Mississippian Oungre Zone and the Ordovician Red River 'C' Zone . Reservoir creation and the pooling mechanism are the result of dolomitization by the seepage refluxion of dense, Mg-rich brines beneath restricted, hypersaline lagoons. When formulating an exploration/ exploitation program for these oil prone horizons, it is essential to understand the complete geological history in order to establish where the reservoirs will be found and to define the areal extent of each accumulation."

Jan 1, 1984

When the Mining Bill came before the Victorian Legislature not so many months ago, the question arose whether mining managers required education, and to what extent. Some members of the House expressed themselves in a way which appeared to leave the impression that mining managers would be all the better if they were not brought up in a scientific school.To try and prove what we owe to science I will give a short history of colonial mining from the earlier period to the present time and compare results.I believe I am right in saying that South Australia is the pioneer colony in mining and to her belongs the credit of not dnly being the first mining colony, but also that her beginning turned out so successful, as the history of the Burra Burra copper mine will testify. At about the same time a little galena mining was carried on nearer to Adelaide, but as this did not prove a success and was only worked by tributing parties, little notice was taken of it.

By W. W. Culver

The paper explores the substance, circumstances and significance of the Whelpley and Storer Copper Process. The 1866 Whelpley and Storer patent specified a process combining mechanical and chemical engineering. The process called for a down-drafting shaft furnace with a horizontal flue connected at the bottom of the shaft. Powdered sulphide ore was roasted in the shaft and then sent forward fully oxidized to a bath of sulphuric acid and/or calcium chloride. The “water furnace” was developed in Boston, at a time when the city was home to most Michigan copper mining companies. The process was field-tested at Quebec’s Harvey Hill copper mine. In 1865 James Douglas, Jr. took over management of the Harvey Hill mine with the challenge of saving the family investment. He needed a way to make money from low-grade sulphides. Through his relationship with chemist T. Sterry Hunt, Douglas learned of a possible way ahead using the process developed by Whelpley and Storer. The paper confirms the centrality of publications, meetings, and networking in the advancement of metallurgy. The process is of interest historically, as much as anything, because it is one of the pillars of James Douglas’ distinguished career in copper. INTRODUCTION At the 1866 meeting of the American Association for the Advancement of Science (AAAS) in Buffalo, New York, T. Sterry Hunt (1826–1892) read a paper “On the Metallurgical System of Messrs. Whelpley and Storer.” The paper is part of a chain of events that constitute the foundation of James Douglas’ (1837–1918) success in the copper mining industry. To understand the career of Douglas over the early years of modern copper mining, we must necessarily start with Whelpley and Storer. Going back to Hunt’s paper, he concluded his remarks by asserting that the Whelpley and Storer Process was “capable of such wide and varied application, that it is probably destined to have a very important influence on the industry of the world” (Hunt, 1867a). He reached this conclusion reasoning that the process had overcome a critical metallurgical hurdle (Hunt, 1867a). Hunt, a geo-chemist in modern terms, recalled that the chemist of those years easily separated copper from “sulphuretted” ores by converting it to a soluble salt from which pure metal was precipitated by “an equivalent of iron.” The problem was to “…apply this principle in the working of copper ores on a great scale...” (Hunt, 1867a). Hunt noted that this very problem had “…engaged the attention of many metallurgists, and has given rise to various processes for obtaining copper by the moist way, many of which are nearly or quite perfect in their operation, but are lacking in practicability and cheapness” (Hunt, 1867a). Hunt thought Whelpley and Storer had overcome the low-grade sulphide hurdle with a commercially viable engineering breakthrough. Yet in the history of copper metallurgy, the process is missing. What happened?

Jan 1, 2019

Gold and copper mineralization in the Parkes area is hosted by a meridional sequence of Late Ordovician to Early Silurian igneous and sedimentary rocks on the central northern edge of the exposed Lachlan Fold Belt. The mineralized area straddles two zones separated in part by the Parkes Thrust and exhibiting different styles of deformation and mineralization (Figure 1). The western zone is characterized by gently folded rocks, with shallow dips and weak to non-existent axial plane cleavage. Faulting is restricted to directions oblique to bedding. Numerous occurrences of minor copper mineralization are known, but of recent national importance is the discovery of the Coradgery- Goonumbla porphyry copper-gold deposits by Geopeko Ltd. A resource in excess of 250 million tonnes has been delineated (Jones, 1985), and this represents the first porphyry deposit of sufficient grade and tonnage to be potentially mineable in New South Wales. The eastern zone is much more strongly deformed. Folding is tight with strongly developed axial plane cleavage. Faulting is abundant both parallel and oblique to bedding. Quartz veining is also abundant, and a narrow belt of gold mineralization adjacent to the Parkes Thrust stretches from Forbes in the south, through Parkes and Peak Hill, to Tomingley in the north. Over 31 tonnes of gold have been produced from this gold belt, mostly before 1914, and now three deposits show good potential for redevelopment - Peak Hill, and the London-Victoria and Lachlan lines of lode.

Jan 1, 1987

Mixed integer programming (MIP) has been used for optimizing production schedules of mines since the 1960s. The major problem in the long-term production scheduling for an entire orebody is that the number of integer variables needed to formulate an MIP model is too large to solve the formulation. This number may reach well over one hundred thousand. To overcome this difficulty, this paper presents two new algorithms to reduce the size of the problem. These algorithms assign an earliest and latest possible start date for each machine placement, eliminating the integer variables that correspond to machine placement before its early start date and after its late start date. A case study based on Kiruna Mine, the second largest underground mine in the world, is summarized in the paper. It shows substantial improvement in the solution time required using the new algorithms. This increased efficiency in the solution time of the MIP model allows it to be applied to Kiruna Mine, with the potential to increase substantially the net present value (NPV) of the project.

Jan 1, 2008

By Robert B. Parsons

"Originally intended to be implemented in 1977, but actually introduced effective May 6, 1974, the earned depletion regulations have been substantially refined and modified since their appearance on the Canadian tax scene, so that this important legislation now consists of a highly complicated set of rules which even the most astute follower of tax law has considerable difficulty sorting out!This month, Tax Notes attempts to cut through this bewildering array oj regulations, in reviewing the main features of the earned depletion allowance applicable to mining operations. Despite the phase-out of earned depletion allowances for most oil and gas operations as part of the federal government's new National Energy Program, earned depletion provisions are still alive and well for the mining sector, although they might well be slowly strangling to death in their own entanglement of complexity!"

Jan 1, 1981

Earnest Advocacy - A Key to Sustainable Minerals Industry Education - A Philippine Experience

Sep 13, 2010

By H. G. Moulton

THE INCREASING scale of mining operations over the past decade, particularly in connection with the exploitation of large bodies of comparatively low-grade copper ores, has made necessary the study of the behavior of rock under failure. When extractions of as high as 40,000 tons a day are reached in steam-shovel operations and as high as 20,000 tons per day in underground mining operations, it is evident that excavations soon become of such size that the behavior of the rock will often be dependent on fundamental principles applicable to more or less homogeneous materials under stress, rather than on weathering or local planes of weakness. In the ordinary rock excavations encountered in civil-engineering practice, such as excavations for subways, highways, railroads, etc., rock faces are not carried to depths sufficient to develop any pressures, or consequently any failures, except those due to loose masses resulting from local planes of weakness. When, however, orebodies whose tonnage is measured by hundreds of thousands are to be extracted by steam-shovel operations in open pits, it is necessary to determine if possible in advance the slopes that the sides of the pits will assume, for these slopes influence the shape of the excavations and thereby the amount of ore that may be extracted by the open-pit method. When large orebodies are mined underground at depths of 300 to 500 ft. (91 to 152 m.) by caving methods, the surface subsiding as the ore is withdrawn, it is necessary to determine in advance the outermost limits of fracture in the subsiding surface, for on the delineation of these limits depends the location of surface improvements, mills, smelters, etc. and also the location of development work, such as hoisting shafts, main haulage levels, and all other underground openings that must remain undisturbed during the period of ore extraction. Heretofore, in civil-engineering practice, it has been assumed that earth and rock behave differently in failure. For the calculation of earth

Jan 2, 1920

By Adel Hanna

Earth pressure acting on piles driven in sand is playing a major role in estimating pile capacity. In literature, researchers entertained simplifying assumptions in estimating the earth pressure acting on the pile's shaft, ignoring the effects of pile installation and pile size. Empirical formulae were introduced based on laboratory or field test results, where major discrepancies can be found among these formulae. In this paper, the theory of cavity expansion and the finite element technique will be used to establish the effects of pile installation technique and pile's diameter on the earth pressure acting on the pile's shaft and accordingly on the values of the existing coefficient of passive earth pressure and overconsolidated ratio. It is of interest to note that pile driven technique and pile's diameter have significant increase on the earth pressure acting on the pile's shaft and accordingly on the overconsolidation ratio in case of loose or medium sands, while they may cause crushing and dilation in case of dense sand. Keywords: Single pile, Cavity expansion, Cohesionless soil, Driven piles, Numerical modelling, Finite element technique, Earth pressure.

Jan 1, 2003

By Jimmy Thompson

The Santa Clara Valley Transportation Authority is designing the Silicon Valley Rapid Transit Project in San Jose, California. The project includes 6.9 km (4.3 miles) of twin-bored tunnels to be constructed through downtown San Jose using two earth pressure balance machines (EPBMs). This paper begins with a project description and update of the project status followed by a description of the relationship between anticipated ground conditions and EPBM requirements. Topics addressed include soil conditioning, abrasion resistance, annulus grouting, face pressure estimation, additional pressure control devices and control measures to limit over-excavation and settlement.

Jan 1, 2008

By Laura McNally

In 2006, McNally International Inc., in a joint venture partner-ship with Aecon Constructors, was the successful bidder on two York Region Tunnel Projects: the Bathurst Collector/Langstaff Trunk Sewers and the York Durham Sewer System (YDSS) Interceptor Sewer 19th Avenue, both in the Toronto area. These projects comprised a total of 13 km (8 miles) of 2.74 m (9 ft) finished diameter tunnels and are both part of the YDSS. Both contracts required the use of earth pressure balance (EPB) tunnel boring machines (TBM) with a precast concrete segmental liner.

Jan 1, 2008

By Shigeru Nishitake

The Earth Pressure Balanced (EPB) shields designed by Mitsubishi Heavy Industries, Ltd., are recently more enthusiastically accepted by tunnel boring specialists. This company having built 1,000 tunnel shields utilizes its vast experience to resolve the problem to excavate through big boulders scattered in rather soft alluvial soil. Several types of EPB shields which can cope with large size boulders are described. Such shields are equipped with both drag bits and rolling disc cutters on the cutterheads. Previously removal of boulders has presented safety problems for workers while in the muck chamber, or venturing in front of the shield. This report describes the problem and how the equipment was modified to deal with the problem.

Jan 1, 1987

By George J. Tamara

The urban environment presents special challenges for the design and construction of earth retention systems. Complications arising from difficult subsurface conditions are compounded by the presence of urban infrastructure and existing and prior construction. The proximity of adjacent structures as well as intense prior use can cause special concerns including the potential for archeological artifacts or contaminated ground or ground water. Utilities and structures may be particularly vulnerable to the effects of ground movement, dewatering and vibrations. Difficulty of access, congestion and limited work areas may severely restrict means and methods of construction. Dewatering may be limited or prohibited because of concerns for disposal of clean or contaminated water, depletion of aquifers, drawing of contaminants to the site or dewatering induced settlements.

Jan 1, 2003

By William S. Heckman

a. When to use: high surcharges, vertical capacity required, limit noise and eliminate vibrations, low headroom, eliminate vibration induced settlements. b. Advantages: eliminates impact noise and vibrations, high section modulus if required, vertical load bearing capacity; corrosion resistant, easy to apply facing for use as a permanent wall, adapts to complex wall layouts, would allow top- down construction, very high uplift resistance. c. Disadvantages: spoil disposal, not water tight, cannot penetrate rock and most obstructions, soil can erode between the piles if surface water and ground water are not controlled, hard to install reinforcing beams over 409 long; subject to high negative skin friction loads, high grout takes in rubble and organic soils. e. Relative cost to other systems: 30% to 50% more expensive than driven soldier piles and lagging except when surcharge loads are involved, or the pile cannot be driven due to noise and vibrations. About the same cost as a sheet pile system. Very competitive if high vertical load must be supported by the wall.

Jan 1, 1997

By John T. Dickman, Ralph E. O’Dette

Chemical Abstracts Service (CAS) is in the process of evolving a computer-based information system which will process all of the material selected for abstracting in the area of chemistry and chemical engineering and its related fields such as the earth sciences and technologies. This system is already operational to some extent and is expected to be fully utilized by 1971. The objective of CAS is to make chemical and related information more readily available, more usable and more used. Chemical Abstracts handle some 5000 abstracts weekly from 13, 000 journals and patents from 25 nations. These cover all of the 80 CA subject sections which relate to chemistry and also extend into areas of interest to geologists, mineralogists, and mining engineers. In this way, CAS fulfills its objective of complete coverage of its major fields, informative abstracting, and indexing to maximum specificity. The concept of a computer-based information system is that of a single machine-language data base into which the results of intellectual analysis of the literature are entered and from which computer programs produce a variety of publications and services applicable to the needs of a wide range of users.

Jan 1, 1969

By R. Sankey, L. Gatty, F. Bizzozero, G. F. Shannon, F. Savaglio, L. McDonald

State mining regulations in Queensland stipulate that a mine be provided with an earth installed on surface and that all underground equipment that needs to be earthed should be connected via a copper conductor to this surface grounding point. The regulations further require that all exposed metal surfaces in underground substations be connected to an earth. In a study of earthing conditions at Mount Isa mine it was found that the physical anchoring of metal work at substations (with rockbolts and associated steel mesh) also provides an excellent electrical connection to the country rock. It was established that not only is the mine's earthing system grounded at numerous underground locations but also that such anchor points offer, in general, a path to ground with lower resistance than does the legally required grounding point on the surface. It is recommended that metalliferous mines should utilise a multiple-earth system and not a run earth connected to a single, above-ground earth point

May 1, 1991

By Tim O’Neil

The earthmover tire shortage has been a case of bust and boom for the tire industry. Tire producers were unwilling to invest ahead of the mining boom. In their defense, though, the metals sector of the mining industry tends to be cyclic, tire manufacturers are not prescient. Until two years ago, low tire demand depressed prices. The incentive to invest in new, big-tire capacity was almost nonexistent, according to Prashant Prabhu, president of Michelin Earthmover Tire worldwide. “There has been very poor anticipation or a miscaluation of the amplitude of the (tire) demand on the part of just about everybody,” said Prabhu. What a turnaround. The earthmover tire market has grown by 30 percent over the past two years. Now there are not enough earth-mover tires and likely won’t be for the next two years. Goodyear said it was offering customers bias-ply tires when it could not supply enough radial-ply tires. Komatsu said it lost equipment sales because it could not provide the tires that customers requested. Volvo and Caterpillar said they are delivering some vehicles without tires, either promising tires later or leaving the customers – mine operators – to find their own rubber.

Jan 1, 2006

By G. Norman Owen, Roger E. Scholl

INTRODUCTION The analysis and design of underground structures to resist vibratory motion due to earthquakes has been of interest to engineers for several decades. The dynamic stability of a powerhouse cavern was considered in the 1960s (Campbell and Dodd, 1967). About the same time, the designers of the San Francisco Bay Area Rapid Transit system developed procedures for analyzing the subaqueous tunnels placed under San Francisco Bay and the tunnels excavated along the land portions of the alignment (Kuesel, 1969). Japanese designers developed fairly sophisticated procedures for analyzing subaqueous tunnels during the late 1960s and early 1970s (Kuribayashi et al., 1974). In the past decade, proposals to site important critical underground facilities in regions with moderate to high seismic activity have increased the interest in earthquake engineering of underground structures. Seismic designs or seismic studies have been conducted for rock caverns for storage of petroleum or location of power plants (Yamahara et al., 1977; Glass, 1976), buried tanks for fuels or rad¬ioactive waste (Fukushima et al., 1977; URS/Blume, 1976), tunnels for disposal of nuclear waste (Yanev and Owen, 1978; Wahi et al., 1980), and urban mass transit tunnels (Monsees and Merrit, 1984). One of the greatest drivers of the interest in seismic analysis and design of underground structures has been the proposals to dispose of high-level nuclear waste in mined repositories some 300 to 600 m (approximately 1,000 to 2,000 ft) below the ground surface. In 1979, the authors, in conjunction with Professor Tor Brekke, presented a paper on an evaluation and design procedure used in a study of a proposed nuclear waste repository (Owen, Scholl, and Brekke, 1979).

Jan 1, 1985

Tunnel damage from explosion and earthquake excitation is correlated with strain and particle motions. Critical strains and motions are then correlated with focal distance, which is so small that permanent strains are highly likely. The shaking process is then numerically modeled to investigate the effects of excitation frequency and joint orientation. The models confirm that near cavern blocks slide intermittently only at relatively high particle velocities during periods of low joint normal stress. Larger displacements occur with relatively small shear wave lengths or relatively high frequencies. Variation in joint orientation and rock mass dilation result in changes in displacement.

Jan 1, 1985

By Ted Budd, Vladimir Goubanov

The East Central Interceptor Sewer, commonly known as the ECIS Project, is the largest public works construction project awarded by the City of Los Angeles. The complexity of this $240 million project, together with the challenge created by the mandated 1,000 calendar days for construction completion, make this project a major interest for the tunneling industry. This paper will describe the ECIS tunnel project, currently under construction by the Joint Venture of Kenny (Sponsor) / Shea / Traylor / Frontier-Kemper. Mining of the18.5 km (about 11 miles) long and 4.7 m (15ft-4in) diameter tunnel is underway with four Tunnel Boring Machines mining at the same time. Details on the mining machines, muck handling systems, innovative construction sequence, together with mining progress will be given.

Jan 1, 2003