Search Documents

By Mauk JL, Arehart GB

Quartz veins from the Martha Hill epithermal gold-silver deposit, Waihi, commonly exhibit crustiform banded textures. Visual differences observed between bands are primarily the result of a 1 to 1500 ¦m variation in quartz grain size. Quartz band textures are dominated by anhedral interlocking quartz mosaics, commonly associated with minor adularia and sulfide phases; these textures are interpreted to be products of amorphous silica crystallisation. The occurrence of rhombic adularia suggests that prolonged boiling influenced parent fluids. In contrast, the presence of coarsely crystalline bands, made up of subhedral to euhedral quartz grains, infers primary crystal growth from solution; evidenced by the occurrence of growth-zoned quartz within these bands. There is a narrow range of 3.3%o in 618Oq,,,,,= between maximum and minimum isotopic values for the deposit. Significant overlap in 618Oqu,, values are observed between the Martha and Welcome lodes. However, statistically significant and commonly systematic differences do occur between individual bands analysed in most samples. Temperature fluctuations may be the dominant factor responsible for observed inter-band variation.

Jan 1, 1995

The relationship between the maceral composition of coal and the strength of the coke produced from that coal has received a great deal of attention in recent years.Studies using two Bulli Seam coals, and blends of Bulli and Wongawilli Seam coals, from the IIIawarra Measures of the Southern Coalfield of New South Wales were carried out.The optimum range of vitrinite was found to lie between 45 per cent and 60 per cent (mineral matter free).Above and below this vitrinite range coke strength deteriorated. Coke strength indices increased with rank, and the optimum vitrinite content increased with an increase in rank. These changes require confirmation as trends by testing a third level of rank. It was noted that vitrinite content decreased with an increase in the specific gravity of separation of the coal.Use of petrographic analyses will increase confidence in choosing coals for coking, provided the coals are well known. Such analyses offer the possibility of greater flexibility in coal purchases and the possibility of producing a marketable blend from coals, which have limited market potential. Critical base coals for blends can be conserved.Significantly more work is required before coal reserves can be utilized to optimum advantage. This work would require extension of the studies discussed in this paper and, in particular, the testing of a wider range of rank.

Jan 1, 1971

The proposed classification scheme is based on two primary parameters, one for petrographic composition and the other for rank, both being determined with microscopic techniques. The scheme has been applied to a wide range of Australian coals and found to provide a useful means of relating their inherent properties to properties such as volatile-matter yield, crucible swelling number, and calorific value, which will determine how these coals might be used commercially.

Jan 1, 1970

By J. Sandford, S. Hennings

EXECUTIVE SUMMARY An approach borrowed from the petroleum industry was applied to the gas development evaluation for the Bulga underground coal mine in New South Wales, Australia. The results enabled the coal mine operator, Xstrata Coal, to systematically plan the extraction of gas in harmony with mine production planning of multiple coal seams. This has allowed for a more proactive approach in preparing the resources and infrastructure needed to capture the gas and accelerate coal mining while maintaining their high level of commitment to safety. Norwest has for decades used gas recovery simulation models to assist the petroleum industry and the coal bed methane (CBM) industry in understanding and forecasting fluid saturations and flow behavior. Norwest developed a similar process with Xstrata to migrate existing mine data at Bulga into reservoir simulation models to study various drainage alternatives. An interesting feature to the evaluation was also developing an understanding of test procedures and nomenclature from the mining industry to properly translate the data for input in simulators developed for the petroleum and CBM industries. The model was then calibrated to actual field data collected from drainage pilot tests that Norwest helped design and monitor at Bulga. The resulting calibrated predictions were then used to develop budgets, schedules, resource requirements, and alternatives for capturing the gas and delivering it to market ahead of mining. Increasing revenue, reducing emissions, improving schedules and cutting costs for the mining operations have all contributed to justifying this advanced approach at Bulga. It has also allowed Xstrata to expand their focus to the sizable gas reserves in seams not currently planned for mining. Several of these seams would be economic gas development targets once the gas recovery infrastructure is installed for the mine. The evaluation process was refined throughout this project and the resulting approach will benefit Xstrata with their broader strategic development of resources in the Hunter Valley and beyond to their worldwide operations.

Jan 1, 2007

By J. Labuschagne

There are a number of factors that contribute to the profitability of a mine and its associated concentrator. Chief among these is the time taken from the first hoist of material from underground to the first batch of concentrate shipped. The main aim of this project was to integrate the mining model with a concentrator production schedule to minimize the time it would take to produce concentrate (without the concentrator having to stop because of a lack of feed material) in the most capital-effective manner. A secondary goal was to ensure detailed stockpiling requirements, as the concentrator is in an area where 'visual pollution' is to be avoided. To achieve these two goals a dynamic stockpile model was created by utilizing the mine production schedule and breaking it down to a daily production figure. Four different concentrator development models were then proposed. The difference between the mine production and concentrator consumption was integrated over the life of the mine to provide the accumulated stockpile tonnages for both Merensky and UG2 ore. To prevent a situation where the concentrator was operational without any feed, the stockpile levels were never allowed to fall below zero. When a development option was selected, the standard metallurgical performance calculations were used to derive a concentrate production schedule, which was used as a basis for commercial negotiations for the sale of concentrate.

Jan 1, 2013

By M. Noaparast, N. Nickoletopoulos, André R. Laplante

"This paper presents an application of the use of synthetic ores to study gold recovery by gravity. Three case studies are presented: the first focuses on the use of tungsten to study applications of Knelson Concentrators for upgrading gravity concentrates; the second on tungsten again, in this case to study the performance of a 86 Falcon Concentrator; and the third on lead to mimic gold's grinding behaviour.It is shown that the use of synthetic ores with metallic substitute for gold is not only expedient, but it can also lead to an increased understanding of separation and grinding mechanisms, because of the more accurate results and controlled particle shapes. The case studies highlight the problems associated with gold particle flakiness and gangue density. The grinding behaviour of malleable materials is shown to be complex, as particles can migrate to coarser size classes by flattening and cold welding, and to finer size classes by folding and actual breakage.IntroductionThe title of this contribution is not entirely misleading. Mineral processing has much to do with philosophy, rather Philosophy, as described by Georgius Agricola:""Furthermore, there are many arts and sciences of which the miner should not be ignorant. First there is Philosophy, that he may discern the origin, cause, and nature of subterranean things; for then he will be able to dig out the veins easily and advantageously, and to obtain more abundant results from his mining. ""1"

Jan 1, 1995

Physical testing of rock support for rockbursting conditions has been carried out for over 40 years. A review of this testing shows that it has been mostly component?based, rather than actually testing support systems. Further, it is concluded that none of the testing is truly representative of rockburst loading in a similitude sense. Similitude conditions are not achievable, mainly because the real conditions in a rockburst event, such as seismic source location and magnitude, wave frequencies, amplitudes, and interactions, are not all known. Because such information is not available, and because the results of all testing carried out to date have not been able to define, for support design purposes, the capacity of support systems, ongoing physical testing of rockburst support systems is essential. It is essential that the test should simulate, or actually take place in, a supported rock excavation. A rock support system is a combination of individual support components that work together to retain and contain the rock. In doing this, the components are subjected to loading by the rock and to interactive loading between one component and another. It is necessary to prove the capacity of such rockburst support systems by subjecting them to severe loading, as in direct blasting. The direct blasting approach, pioneered more than 40 years ago, probably still provides the greatest validity as a significant test of rockburst support capabilities, even though it does not simulate a rockburst. Direct blast testing of rockburst support systems in a surface environment, such as in a quarry or on exposed rock cutting surfaces, could represent a practical development of the approach, facilitating the execution and monitoring of tests.

Jan 1, 2012

By Alan B. Wagner

The River Tower is a proposed 27-story condominium building in the heart of downtown Milwaukee, Wisconsin (USA). The tower will be over 100 m tall, and will have a ground area measuring 15 m by 40 m. The structure will be constructed of cast-in-place reinforced concrete. Certain transfer girders and stabilizing diagonals will be constructed of post-tensioned concrete. Vertical loads will be transmitted through an arrangement of columns, bearing walls, and elevator and stair cores. A mat foundation will be used to connect and integrate these load-carrying elements. The site's geologic profile includes 8.4 m of compressible estuarine (organic) deposits. To control settlement, the mat will be pile-supported. These deposits are underlain by moderate-strength inorganic deposits that extend to bedrock at 32 m.

Jan 1, 2002

By Ren G. Dong, Kristine M. Krajnak, Dan Welcome

Continual occupational exposure to vibrating hand tools can damage the neural, vascular and other soft tissues of the fingers. Rat tail models have been developed to investigate the biological responses of the tissues to vibration.1-2 However, the biodynamic response of the tail relative to that of the human fingers has not been characterized. The objective of this pilot study was to compare the transmissibilities of rat tails measured via a scanning laser vibrometer to those of human fingers gripping a handle. Methods In Part I of this experiment, four male Sprague Dawley rats (6 weeks old) were exposed to discrete 5g-rms sinusoids of 32, 63, 125, 160, 250, and 500 Hz. The rats were restrained in Broome-style restrainers with their tails constrained without compression to an exposure platform via elastic straps as shown in Figure 1. The platform was attached to a vertically vibrating shaker. The vibration was measured for the array of points shown in Figure 1 using a scanning laser vibrometer (Polytec) and the transmissibility calculated for each point on the tail relative to the reference points on the platform. In Part II, three male human subjects were exposed at the frequencies specified in Part I - with the addition of 1000 Hz - at a magnitude at the ANSI <0.5-hr limit up to 63 Hz, after which the acceleration was held constant at 5g-rms. The subjects gripped an instrumented handle at 20 N as shown in Figure 2. The transmissibility was calculated relative to the reference points on the handle. [ ]

Jan 6, 2006

By Trevor Harris, Martin Harris

"This paper evaluates the effect of grind size on the flotation performance of a platinum ore from the UG2 reef of the Bushveld Igneous Complex, in South Africa. The study was conducted on the Mintek Flotation Pilot Plant Facility, located in Johannesburg, and represented a thorough evaluation of the application of the flotation modelling methodology developed jointly by the University of Cape Town and the Julius Kruttschnitt Mineral Research Centre at the University of Queensland through the AMIRA P9 Project. A simulation model of the pilot plant data was successfully implemented, providing a set of circuit modelling parameters that appeared to be both consistent and well correlated to measurable characteristics of the ore and the pilot circuit operating conditions. The findings indicate that the methodology that was used could well provide a useful framework for developing optimisation criteria for industrial flotation circuits in combination with appropriate feed grind size and regrind size targets.INTRODUCTIONIt has long been recognised that the size distribution of an ore is one of the most important factors in the determination of the performance of a flotation process. It therefore follows that the optimisation of a flotation plant cannot be considered without due recognition of the interdependence of this process with the process of comminution. There are numerous qualitative guidelines for the selection of an optimum grind target for a particular operation. Mineralogical analysis can readily provide information on liberation as a function of grind, and the desirable particle size range for optimum mineral flotation is well established in both theory and practice (see for example Trahar, 198 1). For some operations, meeting these two criteria simultaneously is relatively simple. For the majority of operations, such mineralogically “easy” deposits, if they ever existed, have long been exhausted, and the optimum grind represents a highly complex compromise between liberation and overgrinding of both desirable minerals and gangue. This is particularly true for circuits that include regrind stages, where both primary and secondary (and sometime even tertiary) grind targets must be specified. As has been pointed out in a recent paper by Bazin and Hodouin (2001), there is little or no information in the literature to assist plant engineers in the selection of optimum grind targets for complex ore deposits, so current practice is primarily based on rules-of-thumb and experience. This problem is further compounded by the fact that once grind targets have been selected for a particular operation, the assessment and adjustment of these targets based on plant surveys is extremely difficult, time consuming and expensive, and is often not attempted unless the plant significantly underperforms relative to expectation. It is therefore clear that the development of a practical quantitative approach to this problem is a high priority for flotation research and development studies."

Jan 1, 2002

The construction, commissioning and operation of a continuous pilot-scale selective agglomeration (oil agglomeration) unit are described. This plant has been used to recover fine coal from an effluent stream that is produced by a jig plant which scalps the coal from a New South Wales (Australia) colliery. The reject slurry is extremely fine (66.5% minus 53 um) and has an ash content of approximately 40%. The pilot plant can treat up to 0.3 tonne/h of this slurry, producing average product ashes as low as 9.1% and tailings ashes greater than 80%. The average yield observed was62%, which corresponded to a recovery of coal material of 88%. The operation of this pilot plant yielded data that enabled an economic assessment of this type of processing to be carried out. This study showed that selective agglomeration is an economically viable process for eliminating the substantial losses of coal to tailings ponds and minimizing consequent disposal and environmental problems. A commercial plant has been constructed and commissioned on the basis of the data obtained from this pilot-scale operation.

Jan 1, 1979

By Robert B. Francini

Longwall mining and pipelines have coexisted since longwall mining was introduced into the United States. How the pipeline operator reacts to longwall mining under their line depends on many factors. This paper outlines the process the pipeline operator goes through to determine the appropriate response when their pipeline is being undermined. Typical mitigation procedures are reviewed. Finally, the paper looks at current design practices for new pipelines that are expected to be undermined during their lifetime.

Jan 1, 2011

By D. G. Hulbert, J. H. Schubert, R. G. D. Henning

"Froth depth, along with reagent addition and aeration rate, is one of the crucial factors that can be used to control a flotation circuit. Sub-optimal setpoints and disruptions in levels have a severe adverse influence on grades and recoveries. A novel control strategy has been developed which provides exceptionally tight regulation of pulp levels. The controller observes and acts on all the flotation levels simultaneously. This provides a clear improvement over the standard approach, which is to use a set of Pl controllers. The system has been run on several industrial plants and has resulted in reduced fluctuations in level; fast responses to setpoint changes, and fast settling times after start-ups or disturbances. Testwork has shown that the improvements in level stabilisation translate into improvements in recovery and grades.IntroductionProcess control and optimization have an important influence on the economic efficiency of flotation plants. Inefficient operation can allow the wrong balance between grades and recoveries, and can also lead to adverse shifts in the grade-recovery relationship. Of all metallurgical operations, flotation loses the largest proportion of valuable material. Better operation can reduce these losses.An essential requirement of a good controller is that it should be able to stabilize and regulate the plant. Stable operation allows the performance of the plant to be observed without being obscured by the effects of disturbances and fluctuations. The optimum conditions can then be detected more easily. Good regulation can maintain operation at the optimum with proper neutralization of disturbances. Only when good stabilization and regulation are achieved can an optimizing strategy be properly applied.Froth depth, aeration rate and reagent addition are the three means by which a flotation plant is generally controlled. These control actions are effective on different time scales. Reagent addition is slower in its effect as some conditioning time is required. Since reagents are only added at the head of the circuit and at a few selected points within the banks, time is required for the effect of reagent changes to move through the circuit. Because of this slower time constant, reagent addition is more suited to process optimization and to dealing with slower changes in the process. An example of these slower changes is variation in the feed."

Jan 1, 1995

In the early stages of opening up a mine, when there is some uncertainty as to its future career, necessitating caution in laying out works of a permanent character, the want is often felt of an assay furnace, easily built and easy of transportation, should the&quot; mine &quot; prove to be &quot; no mine.&quot; Again, cases occur in which parties buy the right to treat comparatively small heaps of tailings, and then shift their plant to other localities. Under these circumstances it is necessary to restrict the plant to the barest necessaries, to suit, so to speak, the nomadic character of the work.An assay furnace that is really portable, easily transported, erected, taken down, of little weight, always ready for action on short notice, is indeed in these cases a desideratum which has long been wished for. The gasoline furnaces introduced intothe Australian market some time since practically fulfil these conditions; but they have the fatal drawback of being dependent on a constant supply of the liquid fuel, gasoline, which is seldom, if ever, obtainable locally in&apos; any wayback mining township...

Jan 1, 1904

By P. Lopez, E. Wellman, N. Risso, A. Anani

Current machine learning models used for roof fall hazard prediction are mounted on expensive sensors, computationally expensive, or lack the robustness for accurate prediction in the underground mining environment. This research aims to provide a design methodology for a robust, low-cost, deep learning-based algorithm for underground mine roof fall hazard prediction. A data sampling plan is developed to ensure the replicability and robustness of the developed model. In addition, feature engineering and transformation methods are described to identify relevant features for hazard identification. The methodology described here will be used in model development, tested, and implemented as a real-time mobile device application. The new tool will be expected to detect roof fall hazards in real-time and contribute to a crowdsourcing approach for underground hazard detection.

Feb 1, 2023

By Bahram Sameit

Blast engineers have been taking advantage of image-based rock fragmentation analysis methods for the past three decades to estimate rock size distributions. These methods utilize a range of image segmentation techniques, from manual to fully-automated, to delineate the edges of rocks in images. Rock delineation results are then converted to physical rock sizes (and percentage passing curves) by scaling the image pixels to correspond to physical measurements. The size scaling process is critical for acquiring physical measurements, but specifc to the limitations of different applications. This article starts by presenting a shovel bucket-based fragmentation analysis system, where scaling is done using the known width of the shovel bucket within the image. It will then describe methods that use pictures captured by digital cameras with scaling reference objects in the view. Finally, the article presents a method that uses three-dimensional imaging to capture images without the need for scaling reference objects.

By Jim Ploger, Peter W. Johnson

Bus drivers represent a large segment of the US transportation industry and research has shown an association between exposure to Whole Body Vibration (WBV) and the high rates of low back disorders. Impulsive WBV exposures have been recognized as a risk factor for low back injury and new guidelines exist for their measurement and assessment (ISO 2631, Part 5). Methods to accurately and better characterize the impulsiveness of WBV along with the temporal patterns of the exposures are needed. The development of a hardware and software system to measure continuous TWA and raw, impulsive WBV exposures and the design of a subsequent study are presented. Methods Using two Larson Davis HVM 100 as accelerometer amplifiers, small external batteries, and a Pocket-PC (PDA) with 1 Gb of compact flash memory, we can collect up to 16 channels of data for a full day 600 Hz. Tri-axial WBV exposures will be measured and characterized at the frame of the bus and at the driver/seat interface (seatpad accelerometer). Using a repeated measures design, 20 bus drivers will drive on selected routes which include both city streets and highways, and within and between subject components of variability and exposure determinants related to the bus, bus seat, the bus driver, and the route will be identified. Global Positioning System (GPS) data will also be collected and integrated with the WBV exposure data to facilitate the identification of the location, velocity and type of road associated with high average TWA and impulsive WBV exposures. This system may be used to develop administrative (alter speed and/or route of bus, systematically vary type of routes) and/or engineering controls (identify and trigger the need for street repair) to reduce high WBV exposures. Results Our portable Pocket-PC based data acquisition system is up and running and we can collect seven channels of WBV data (seat pan tri-axial accelerometer, bus frame tri-axial accelerometer and GPS data) continuously for a full shift. The software analysis of the data is complex but nearing completion. We have incorporated the vibration dose calculations from ISO 5321, Part 5 and have obtained a Matlab-based routine to appropriately weight the continuous signals. Discussion In summary, the measurement of WBV is complex but new technologies open avenues of collecting and assessing WBV exposures that were previously not possible. The standardization of impulsive WBV exposure assessment methods is needed to further the discipline and better enable comparisons across studies.

Jan 6, 2006

Collecting the clay fraction of active stream sediment from a flowing stream for geochemical analysis i a difficult process. One either takes a sample of dry fine-grained sediment from the stream bank (dry weather and dry sample are uncommon in parts of New Zealand and Tasmania), or dredges up a sample of sand and mud out of the stream.The latter method produces a soggy ample bag full of mud and sand, with varying amounts of gravel, depending on the size of the stream. The water can be filtered from such a sample by means of a Buchner filter funnel, but is difficult to obtain a vacuum in the bush. This problem can be solved by using a small hand- queeze bellows such as used in priming petrol pumps on outboard petrol motors. The common laboratory hand bellows is not powerful enough.A 70 mm diameter two-piece polythene Buchner filter funnel (Fig. 1) can be used. A length of rubber tubing is fitted around the inlet valve of the hand bellows and this valve is then jammed into the pipe at the bottom of the filter funnel (the polythene pipe may be trimmed with a knife to fit over the inlet valve of the bellows). The vacuum is generated and maintained by squeezing the hand bellows.The technique of collecting a sample of the clay fraction is to dredge a sample of the fine-grained active stream sediment out of the stream with a container, such as a plastic mug. The sample is agitated to get the clay fraction into suspension and the muddy suspension is then decanted into the Buchner funnel. The desired clay fraction is obtained as a thin film on the filter paper.If the &quot;fines&quot; are also required, a filter of nylon bolting cloth (stretched across the mouth of a short length of 80 mm diameter polythene pipe and attached by rubber bands or a concentric polythene pipe) can be placed over the mouth of the Buchner funnel and the whole sample of stream sediment...

Jan 1, 1969

By Thompson D, Somerville JM, Brock DA

The development of a softwood alternative to the hardwood chockpiece used to build the waste-edge breakers commonly incorporated in gateroad packs is described. The results of laboratory tests on softwood prototypes and two underground trials are presented. The results of the last trial suggest that a viable alternative chockpiece has been designed, offering advantages over availability of wood, weight and given reduced wood content, price.

Jan 1, 1992

Rockbursts continue to be a scourge in the mining industry, being responsible for accidents and damage to mining excavations. Although the problem has been present for more than a century, and although much research has been carried out, a solution is still elusive. Determination of, firstly, the demand on the support system imposed in the rockburst and, secondly, the capacity of the support system, cannot be carried out with any confidence, and therefore rockburst support cannot be designed using a conventional design approach. In contrast with the conventional approach, observations of rockburst damage in a mine have revealed a possible alternative approach to rockburst support ? sacrificial support. It was observed, in rockburst events, that a support system consisting of concrete panels restrained by grouted cables was destroyed, and the concrete panels were ejected. However, the rock behind the panels remained apparently undamaged and in place. This behaviour reignited the concept of sacrificial support, conceived more than 20 years ago, and which is described in this paper. The remedial solution implemented on the mine, involving cables wrapped over the panels and retained by grouting into boreholes, has been subjected to rockburst loading and has confirmed the validity of the sacrificial support concept. The concept of sacrificial support may be controversial, but is deliberately presented here with the aim of generating discussions and contributions, and with the ultimate aim of improving safety and reducing rockburst damage in mines. Keywords rockburst, seismicity, seismic waves, rock support, support design.

Jul 1, 2013