Search Documents

By B. Unver

Effective strata control is a prerequisite for maintaining an efficient mining operation. If the strata in the vicinity of an opening are not controlled effectively, it is impossible to perform a safe, efficient and economical operation. In this paper, the reasons and outcome of instability problems observed in roadways opened in clay and marl at the Bolu Colliery of Yeni Çeltek Establishment are investigated. Roadways under examination were located in a syncline causing high residual tectonic stresses. Factors affecting the instability have been studied thoroughly by examining geology and tectonics of the area, establishing convergence measuring stations to understand in situ behaviour of supports and laboratory tests to determine engineering properties of samples taken from nearby convergence measurement stations. As a conclusion, a new production strategy and a new support system are recommended to maintain stability.

Jan 1, 1999

By Murat Baydogan

Effect of retrogression and reaging treatment on hardness and stress corrosion cracking resistance of 7075 aluminum alloy was investigated. As received 7075 alloys in T6 temper condition were retrogressed at 170, 220, 240 and 380°C for different durations between 15 s and 60 min. Subsequent reaging was made at the T6 aging condition. Treated materials exhibited higher hardness and better stress corrosion cracking resistance than T6 temper in a wide range of retrogression temperature and time. The highest hardness was obtained after retrogression at 170°C for 210 s followed by reaging, corresponding to 20% hardness improvement. Improvement in stress corrosion cracking resistance of the alloy by as much as 85% was also observed. In this paper, improvements in hardness and stress corrosion cracking resistance are discussed on the basis of the microstructural changes during retrogression and reaging treatment.

Jan 1, 2006

By Rajagopala Reddy Kallu

After the Sago and Darby No. 1 mine incidents, the new regulatory standards for the design of mine seals in underground coal mines of the United States require the mine seals to withstand higher explosion standards. This necessitated for the development of new design approaches and standards. For development of any new design standards or approaches a detailed understanding of effect of key influencing parameters on the stability of mine seal is a must. This paper attempts to address one of the factors, i.e. roof convergence, that play an important role in the stability of mine seal under explosion loading. Initially a couple of three dimensional numerical models were built and tested for different levels of roof convergence. These models confirmed that roof convergence has great influence on seal stability. A detailed study is undertaken, with some simple assumptions, to establish typical influence of roof convergence on the stability of mine seal under different levels of static explosion pressures. Three dimensional distinct element code 3DEC is used for this purpose.

Jan 1, 2007

By J. E. Chilton

The National Institute for Occupational Safety and Health (NIOSH) has conducted research to determine the influence of mining machine-mounted scrubbers on airflows and methane concentrations at the face when blowing ventilation systems are used. Tests were conducted in a full-scale ventilation gallery with a model mining machine that simulated airflow created by a dust scrubber. During the tests, ultrasonic anemometers were used to measure airflow speed and direction at several locations near the face. For the same test conditions, methane was released from the face and gas concentrations were measured at 21 locations above the machine using fixed point methanometers. Changes in airflow speed and direction are correlated with scrubber airflow and the measured methane distribution above the mining machine. The research results showed that operation of machine-mounted scrubbers improved face ventilation when blowing ventilation is used by increasing both the intake flow and the quantity of air reaching the face.

By F. Chiesa, Jeremy Carignan, B. Duchesne, D. Levasseur

"Aluminium A206 (AlCu4) is one of the strongest aluminium casting alloys with tensile properties approaching those of ferritic ductile iron. If the specification on the silicon content (< 0.05%) is easy to achieve during alloy ingot production, it is not the case in a foundry, where returns are used which are not perfectly cleaned from the silicate containing molding sand (Olivine). In alloy A206, the Si content is controlled in order to avoid the formation of a low melting point intermetallic phase (such as phase Q Al5Cu2Si6Mg2); these phases will melt during the solutionizing heat treatment to which alloy A206 must be subjected to develop its outstanding mechanical properties. This incipient melting may deteriorate the mechanical properties of Alloy A206 if the solutionizing treatment is applied at the standard temperature of 530°C.In the present study, a lower temperature solutionizing (520°C) was applied to a high Si content 206 alloy in order to reduce or eliminate the possible incipient melting. This was carried out on a complex shape industrial casting weighing 14 kg (31 lb) and 560x410x250 mm (22x16x10”) in size poured in aluminum 206 with a high silicon content (0.22% vs 0.05% max for alloy A206). Twenty ASTM E8 subsize tensile specimens were excised from two locations in the casting in order to compare the tensile properties for the two solutionizing temperature used (530 and 520°C). Optical and SEM microscopy allowed to investigate the causes of the differences in the properties observed between the 2 zones of the casting studied for 3 different heat treatments. INTRODUCTIONIn spite of their “textbook” outstanding mechanical properties (Up to twice the strength and elongation of the widely used A356 alloy), aluminum-copper alloys of the 2xx series are seldom used because of their propensity for hot tearing [Li, 2011], the segregation of copper [Cho, 2003], and their sensitivity to stress corrosion cracking [Jean, 2009, p. 113)]. Also, because of their wide freezing range and high thermal conductivity, a wide mushy zone makes feeding difficult, unless strong temperature gradients are created by liberal use of chills and risers in the critical zones of the part. Because they are prone to hot tearing, grain refining of Al-Cu alloys is particularly important, titanium playing a major role in the process [Sigworth, 2003]; grain refining has also been shown to be beneficial to fatigue strength [Jean, 2009, p. 103]. The practical basis of foundry practices pertaining to these alloys is outlined in an AFS webinar [Weiss, 2014]."

Jan 1, 2016

By Robert H. Hafner, Irvin R. Kramer, Stewart L. Toleman

IN his paper on the calculation of hardenability from chemical composition, Grossmann1 discussed the effect of most of the alloying elements used commercially. The purpose of the work reported in this paper was to determine the effect of several other elements on hardenability-arsenic, antimony, beryllium, cobalt, columbium, germanium, tellurium, tin, aluminum, and titanium-and to extend the range of composition of some of the elements studied by , Grossmann-chromium, copper, manganese, molybdenum, nickel and silicon. EXPERIMENTAL METHODS To determine the effect on hardenability, suitable amounts of the alloying elements were added to experimental heats and the hardenability determined by means of end-quenched hardenability specimens. The steels were melted in a high-frequency induction furnace with a basic crucible, using ingot iron as a base for some of the heats and S.A.E. 1015 for others. The alloying additions were made as ferroalloys or as metal, depending on the &apos; alloying element. Hundred-pound heats were split and poured into square, tapered, cast-iron ingot molds with hot tops. Aluminum was not used as a deoxidizer in most of the heats. The ingots were homogenized for 12 hr. at 1260°C. (2300°F.) , and forged into rounds of 1 ½ in. diameter. These bars were normalized twice from 840°C. (1550°F.) before machining into Jominy bars. The composition of the steels was deter- [ ] mined in most cases by samples taken from the end-quench hardenability specimen. As suggested by crafts,2acid-soluble

Jan 1, 1943

By K. [Muthukkumaran

An extensive program of laboratory model tests was undertaken to study the effect of slope on p-y curves under passive loading in dry sand. The paper concerns the method developed in a series of laboratory model tests to experimentally determine p-y curves. Bending moment curves are differentiated by using curve fitting method of cubic polynomial function. The study includes effect of slope angle and relative density on bending moment and non-dimensional p-y curves. The non-dimensional p-y curves for piles on sloping ground under passive load are developed modifying API method by including a Reduction Factor (R) using the experimental results.

Jan 1, 2006

By Larry M. Southwick

Extraction of gold and other metals from ores suspended in liquid slurries often involves gases (such as oxygen) as a participant in the reaction. An important factor then in setting the rate of extraction can be mass transfer of the gas into the liquid and/or solids. A number of recent studies have indicated that as solids loadings increase, mass transfer rates of gas into solid-liquid mixtures decreases. This would seem to imply that lower solids loadings would be beneficial to increased reaction rates. However, since it is the solids which are being reacted, a most intriguing paradox is created. More solids should lead to more surface area to react, but it seemingly also provides less gas to react. So is the reaction faster or slower as solids loadings increases? The creation of this paradox is imbedded in how mass transfer and reaction data is collected and measured, how it is analyzed and correlated, and finally on the rate controlling steps in the reaction. An alternative analysis of these studies is presented which clarifies and eliminates the paradox. The analysis applies to water slurries as used in gold or other metal leaching processes or in bio-hydrometallurgy, as well as to molten metal/solid/gas mixtures such as might be encountered in submerged gas injection.

Jan 1, 1999

By B. Kahraman

About 70% of the world?s total boron reserves are located in Turkey. Boron minerals are typically concentrated by attrition scrubbing followed by screening and classification to remove clay minerals and other impurities. These wet concentration methods, however, result in a considerable amount of accumulated tailings in large tailings dams. The tailings are approximately 28% solids and contain 14% B2O3. Problems caused by these tailings can be minimized by employing dry beneficiation techniques involving heat treatment. This method has been successfully tested on laboratory and pilot scales. During heat treatment, borax undergoes expansion in volume. The amount of expansion is dependent on the particle size, temperature and duration of heat treatment. Because the optimum temperature and the duration of the heat treatment are not well defined, the boron ore acts as a calcined clay mineral and is discarded along with the gangue. It is important to predict such parameters using mathematical formulations. Thus, a mathematical model is used to predict the required temperature and duration period prior to heat treatment. In the experimental study presented here, a series of systematic thermal tests was carried out in a muffle furnace. Two variables, temperature and time, were studied in a response surface design. A quadratic regression model was chosen and regression coefficients were calculated. Using a regression equation, the volume expansion of the particles in various circumstances can be predicted. The mathematical test results are then correlated with the experimental results to relate the optimum expansion of borax with heating time and temperature and with borax grades and recoveries.

Jan 1, 2008

By H. A. Bilgin, G. G. U. Aldas

"Ground vibration is the natural result of the blasting process. Many empirical formulae and methodologies including analysis of travel path effects have been developed. The scaled distance, which is the most popular approach for the calculation of the attenuation of particle velocity in the ground, has led to significant advances in the prediction of particle velocity when both explosive charge and distance vary. However, this approach does not consider the effect of ground anisotropy and existence of structural geological features on ground vibration. Therefore, in this study, the effects of these rock mass properties on types, amplitudes, and frequencies of ground vibration waves at four surface mines are examined. The results, which were implemented at Kangal coal mine, Bastas quarry and Kíbrís quarry, provided guidance for the extensive study at Orhaneli surface coal mine.As a result of the study, the authors came to the conclusion that vibration amplitudes change depending on the ground on which sensors were deployed and the conditions depending on whether measurements were done near major structural geological features. It was determined that the vibration amplitudes, measured at equal distances from the source but in different directions, change because of the propagation velocity anisotropy. Besides the change of wave type due to the kind of ground at the measurement location, it was determined that vibration anomolies were due to structural features."

Jan 1, 2004

Effect of Spacer Chain Length on the Flotation of Kaolinite and Quartz by Using Gemini Surfactants as Collector

Sep 13, 2010

By A. W. Khair

Laboratory studies indicate that the specimen size influences the compressive strength of coal significantly. In the past, the diameter/height ratio of coal and rock specimens with different geometry and its influence on failure characteristics was discussed (Khair, 1993; Khair, 1994; Khair and Xu, 1994). In the current attempt, tests are designed and carried out under uniaxial condition in the laboratory to investigate the influence of specimen size. Cubical specimens of coal with edge dimension ranging from 5 cm (2 in.) through 20 cm (8 in.) were prepared according to the standards and tested uniaxially. Results show that compressive strength of coal is dependent on specimen size until certain level and later the change in specimen size would not yield significant change in compressive strength. Cubical specimens were chosen for testing because they are not only in close resemblance to underground pillars, but they are also the most stable shape under loading. The failure characteristics of these specimens were analyzed and their applicability to pillar design aspects in coal mines is studied. A detailed analysis of the physical and mechanical properties of the tested coal seam is also presented.

Jan 1, 1996

By S. F. Fu

The Charkhan Salt Lake area of the Chaidamu Basin in West China is characterized by soft super-saline soils with very high contents of soluble salts. From the engineering point of view, these saline soils are saturated, liquid-plastic and moderately to highly compressible lean silty clay and clayey silt. In the natural state, their allowable bearing capacity is only 60-80 kPa. As to the saturated lean silty clay, liquifaction in case of an earthquake of intensity 7 on the Modified Mercalli scale is considered likely. In order to improve the geotechnicai properties of the saline soils, stone colomn stabilization by means of vibroflotation was performed. As the geotechnicai properties of the soils are closely linked with the amount and composition of the soluble salt content, saline water with chemical content similar to that of the saline soils was used as flush fluid in the course of hole-making and column-forming, with a view to keeping unaltered the amount and composition of the salts in the soils and thereby precluding reduction in or loss of their strength. Systematic monitoring on the behavior of the foundation soils before and after the treatment and comparison of the numerical data thus acquired have shown good technical results, testifying to the effectiveness of stabilization of soft superealine soils by vibroflotation. As a result of the treatment, the allowable bearing capacity was increased one to two fold, accompanied by elimination of the liquefaction potential.

Jan 1, 2010

By Xiaodong Ma, Marek Pawlik

Introduction Guar gum is a natural nonionic polysaccharide. Guaran, the functional polysaccharide in guar gum is a chain of (1?4)-linked ß-D-mannopyranose units with a-D-galactopyranose units connected to the mannose backbone through (1?6) glycosidic linkages. The poly-mannose chain is randomly substituted with galactose units at a mannose-to-galactose ratio of 1.8-1.0 [1]. Cheng et al. reported that the molecular weight of natural guar gum is 1.935 • 106 [2]. Robinson et al. found that the molecular weights of five grades of commercial guar gums ranged from 4.4 • 105 to 16.5 • 105 [3]. Guar gum is frequently used as a depressant of naturally hydrophobic gangue minerals (e.g. talc) in the flotation of PGM-bearing ores, and according to Harris et al. a wide variety of modified guar gums are available for this application [4]. The Canadian potash industry utilizes natural guar gum as a blinder of water-insoluble slimes in the flotation of potash (sylvinite) ores, a process that is carried out in a saturated KCl/NaCl brine. The role of the polysaccharide is to prevent a primary amine collector from adsorbing onto these unwanted fine minerals. Hydrophobic interactions between basal cleavage planes and the polymer appear to be involved in guar gum adsorption on talc [5,6]. Liu and Laskowski stressed the importance of metal impurities on mineral surfaces that can serve as the active sites for polysaccharide adsorption [7]. This postulate was consistent with the later observation that, in addition to hydrogen bonding, the adsorption of guar gum onto talc was strongly dependent on the surface concentration of magnesium sites [8,9]. In this case the adsorption process was visualized as metal-polysaccharide complexation facilitated by the cis-configuration of the hydroxyl groups of mannose monomers. Hydrogen bonding and chemical interactions with metal sites were also suggested by Rath and Subramanian in their studies on guar gum adsorption on biotite mica [10]. In a recent study, Wang et al. demonstrated that hydrogen bonding is the main driving force behind guar gum adsorption onto talc [11]. Their data also show that the adsorption density of guar gum on alumina is about five times lower than the adsorption density on talc. Pawlik and Laskowski reported that the amount of guar gum adsorbed on illite was independent of ionic strength over a wide range of salt concentrations [12]. The adsorption density of the polysaccharide on illite did not measurably change with ionic strength from that of distilled water to about 50%-saturated KCl/NaCl potash brine (~3N KCl/NaCl). However, guar gum adsorption on dolomite dramatically decreased over the same range of ionic strengths, and no reliable explanation of that phenomenon was proposed [12]. The water structure-breaking or structure-making capabilities of background ions are usually ignored when discussing adsorption mechanisms of polymers. The concept of “structure breakers” and “structure makers” was first introduced by Gurney, and Frank and Wen who postulated that each ion is surrounded by three distinct regions of water structure [13,14]. In the first layer, water molecules are tightly bound to the ion. The second region extends farther away from the ion and is referred to as the region of structure breaking. Only at larger distances, where the ionic field is weak, water molecules form the “normal” ice-like structure. It is also now recognized that the first layer can be further divided into the primary and secondary hydration shells. Small, strongly hydrated ions reinforce the “normal” structure of water and the region of structure breaking disappears. In contrast, large less-hydrated ions disturb the ice-like structure and generate an extensive region of structure breaking. Experimentally, these two effects can readily be distinguished through viscosity measurements. Increasing concentrations of structure-breaking ions result in a decrease of the viscosity of aqueous solutions. On the other hand, increasing amounts of structure-makers significantly reduce the viscosity of water. Alkali metal cations form a sequence known as the Hofmeister series. The Hofmeister series - Cs+, K+, Na+, Li+ - orders the cations from the least hydrated to the most hydrated. Based on literature viscosity data for aqueous

Jan 1, 2005

By Darrell Wilder

When designing excavation support systems in urban environments, it is often necessary to consider the effect of vertical surcharge loads from adjacent structures. Several methods are used in practice to establish the horizontal surcharge-induce pressure on the excavation support. According to the experience of the authors, these methods often seem to overestimate the effect of the surcharge and may have significant impact on the construction costs. This paper explores several of these procedures and provides a discussion as to the reasons for the differences in surcharge effect predictions between different procedures. It also provides practical recommendations for designers dealing with excavation support design.

Jan 1, 2006

By Fumihiko Sumiya, Kunihisa Katsuyama, Yuji Ogata, Yuji Wada, Yukio Katoh, Yoshikazu Hirosaki

In our previous work, the results of photographic observation using a high speed framing camera showed that the difference between precursor air shock wave velocity and detonation velocity was primary factor for the channel effect. It is assumed that the decreasing precursor air shock wave velocity can prevent the channel effect in charge hole.

Jan 1, 1996

By L. M. Demers, D. C. Kuhn

"Kuhn, Douglas C., and Laurence M. Demers. Effect of surfactant on basal and silica-induced eicosanoid production by the alveolar macrophage. Am. J . Physiol. 269 (Lung Cell. Mol. Physiol. 13): L165-Ll 70, 1995.-Infiammation and fibrosis subsequent to the inhalation of certain mineral dust particles has been suggested to result from the activation of eicosanoid synthesis by the alveolar macrophage (AM). To determine if surfactant modifies dust-induced generation of eicosanoids by the AM, we evaluated the effect of the surfactant lipid dipalmitoyl lecithin (DPL) on the production of eicosanoids by rat AM exposed to respirable silica dust in vitro. During the first 24-h exposure period, DPL alone significantly increased basal production of eicosanoids but completely inhibited silica-induced thromboxane A2 synthesis. In contrast, leukotriene B4 (LTB4 ) production was only partially reduced by DPL. During a second 24-h exposure period, LTB4 production in response to the highest dose of silica remained significantly elevated in the presence of DPL. Similar results were obtained when the surfactant preparation Survanta was evaluated. These results suggest that 1 ) DPL and Survanta independently activate AM eicosanoid production, 2) DPL and Survanta modulate the response of the AM to silica dust, and 3) L TB4 may be the most important eicosanoid mediator of the long-term effects of silica dust exposure on lung pathophysiology. THE OXYGENATED METABOLITES of arachidonic acid (AA) (here collectively termed eicosanoids) have been implicated as important regulators of lung physiology and are thought to be involved in pathophysiological sequelae such as acute respiratory distress syndrome, asthma, and the pulmonary complications of sepsis (20). This role is manifested through both direct effects on lung physiology as well as through an indirect modulatory effect on the release of other mediators of lung injury, in particular profibrotic cytokines such as the interleukins and tumor necrosis factor (15). Recently, exaggerated eicosanoid production by both the alveolar macrophage (AM) and the type II epithelial cell has been demonstrated to result from the exposure of these cells to several particulates, including crystalline silica (quartz) dust (5, 9, 17). These observations have led to the suggestion that eicosanoids play a major role in the etiology of pneumoconioses.Another secretory component of the pulmonary environment, surfactant, has been shown to modulate crucial AM functions, such as bactericidal activity and the recruitment of circulating immune cells (25). Indeed, an important feature of the lung's reaction to inhaled mineral dust is an increase in surfactant production, perhaps as a compensatory or protective response (1, 16). In addition, the alteration of the surface properties of mineral dust by surfactant or its components has been shown to influence the biochemical response of the AM to the dust, perhaps by altering the surface charge of the dust particle (11, 29, 32). And recently, Wallace et al. (28) have shown that the coating of mineral dust with surfactant, and its subsequent removal by lysosomal phospholipase, unmasks differences in dust cytotoxicity that are not apparent when AM are exposed to uncoated dust. Thus it appears that the inclusion of surfactant in in vitro exposure studies may be important in evaluating both the absolute levels of eicosanoid production by the normal and dust-exposed AM and the temporal relationship between dust exposure and the production of inflammatory mediators by the AM. Therefore, we characterized the effects of the surfactants dipalmitoyl lecithin (DPL; the primary lipid component of natural surfactant) and Survanta (a commercially available surfactant derived from bovine lung) on basal and silica-induced AM eicosanoid production during two 24-h periods after exposure to dust particles to both allow the enzymatic removal of surfactant from the particle surface and evaluate the k"

Dec 1, 1996

By H. Polat, Q. Hu, S. Chander

"The collection efficiency of dust particles was determined in a laboratory dust chamber equipped with a water spray. Measurements were made in the presence of selected nonionic, cationic and anionic surfactants. For the nonionic and the anionic reagents, efficiency was maximum in a narrow range of concentration. The surfactant concentration corresponding to high collection efficiency was usually much below the commonly used concentration of l "", however. In comparison, much higher collection efficiency was observed for a cationic surfactant at extremely low concentrations. For delineating the mechanism of capture of dust particles, surface tension and contact angle results were used to obtain a correlation between the work of adhesion and the efficiency of collection. Such a correlation was reasonable for the nonionic surfactants but not for charged surfactants. In the latter case, electrostatic interactions between charged droplets and particles were more important, especially for the cationic reagent. INTRODUCTIONSeveral methods are used to control dust in mines. These include: ventilation, foam, scrubbers and sprays. This article is concerned with improving the effectiveness of water sprays, which are widely used to remove dust particles during continuous mining, by adding small quantities of surfactants. Water sprays produce small droplets which act as collectors of dust particles suspended in air. Sprays directed at the actual source of dust have the additional property of wetting the coal before the ·particles become airborne (Hamilton, 1974). Wetting agents, also called surfactants, arc known to play an important role in many applications where dust is a problem. However, conflicting reports exist in the literature with regard to the effectiveness of surfactants in water sprays (for a review, see Chander et al., 1988). In spite of the conflicting reports, the use of surfactants for dust control has increased over the years. In a recent study by the Bureau of Mines, a 27'6 reduction in respirable dust levels was observed in a mine test when surfactants were added to sprays (Foley, 1991)."

Mar 1, 1992

By H. Polat, Q. Hu, S. Chander

The collection efficiency of dust particles was determined in a laboratory dust chamber equipped with a water spray. Measurements were made in the presence of selected nonionic, cationic and anionic surfactants. For the nonionic and the anionic reagents, efficiency was maximum in a narrow range of concentration. The surfactant concentration corresponding to high collection efficiency was usually much below the commonly used concentration of l%, however. In comparison, much higher collection efficiency was observed for a cationic surfactant at extremely low concentrations. For delineating the mechanism of capture of dust particles, surface tension and contact angle results were used to obtain a correlation between the work of adhesion and the efficiency of collection. Such a correlation was reasonable for the nonionic surfactants but not for charged surfactants. In the latter case, electrostatic interactions between charged droplets and particles were more important, especially for the cationic reagent.

Jan 1, 1992

By Wu Y. H, Lu J. P

Slope stability has now become a practical tool in the design and oper- ation of open pits. The stability of rock slope depends on many factors, including not only structural geology, the existence of weak layers, ground- water, blasting and weathering, but also the virgin stress field. This paper presents an application of a numerical method to investigate the effect of the virgin stress on slope stability. The finite element method is employed to simulate the excavation of open pits. Redistributed stress fields in the slope of open pit are computed for several different virgin stress fields. Based on the redistributed stress fields, the shear force which tends to produce sliding of a rock mass and the frictional resistance to sliding are evaluated. The possibility of potential failure is assessed by the limit equilibrium method. The combination of the finite element method with the equilibrium method provides a powerful analytical tool for slope stability. The significant effect of virgin stress on the stability of slopes is shown by studying a typical case.

Jan 1, 1989