Search Documents

By W. R. Bendy

GRINDING is a large and costly part of Portland cement manufacture. Prior to clinkering in the rotary kiln, raw materials are ground to a fineness of 80 to 90 pct passing 200 mesh. Then, after burning and cooling, the resulting clinker is ground to about 92 pct passing 325 mesh. In the cement industry the most favored method of grinding has always been by impact and attrition of a ball charge in a rotating mill. Other types of mills, in which materials are ground between die rings and rollers, or between die rings and large balls, are sometimes used for single-stage grinding and often for preliminary grinding followed by grinding in ball-type mills. Their efficiency is usually high, but maintenance and repair costs are high also, and the ball-type mill continues to be the most widely used. Together with 4 pct gypsum to retard setting time, the kiln run clinker—consisting of hard, semi-fused lumps that may have been crushed to — 1/2 in.—is ground to a Blaine surface area of 3000 sq cm per gram and about 92 pct passing 325 mesh. Approximately 32 kw-hr per ton, or 6 kw-hr per 376-1b barrel, are consumed in the grinding mills alone, not counting auxiliaries. Open Circuit Clinker Grinding: Many early clinker grinding plants employed two-stage, open circuit grinding. Comparatively short mills of large diameter, loaded with balls 4 in. and smaller, first reduced the clinker to 95 pct passing 14 mesh. Tube mills of smaller diameter and greater length, loaded with balls 11/4 in. and smaller, carried out the fine grinding operation. An early development was to assemble two or more stages of grinding in a single mill having two, three, or four compartments separated by division heads. There were difficulties in balancing the compartments, but compartment mills were popular in the 1920's because the layout was simple and there were no elevators and conveyors. Oversize Particles: Open circuit mills, whether separate ball and tube mills or compartment mills, always encountered the problem of tramp oversize in the product. A small percentage of clinker survived passage through the first grinding stage as particles—perhaps 1/16 in. diam—that were too large for the smaller balls in the following stages to reduce to —200 mesh. When the feed rate was lowered to reduce tramp oversize, there were serious losses in grinding efficiency. Many ingenious designs were perfected to incorporate perforated screen plates or wire mesh screens in the ball mills or in the first compartments of compartment mills. Their purpose was to prevent mate: rial passing out of the first stage until it was small

Jan 1, 1958

By W. F. Mullen, C. W. Stickler

WITH few exceptions, unit operations in the Pennsylvania slate industry in 1950 did not differ appreciably from production methods described by Behrel and Bowles2-4 several decades ago. Many traditionally picturesque but relatively inefficient hand operations continued to contribute to high operating costs in an industry in which the margin of profit, for various reasons, was admittedly low. As part of a general program in which the Pennsylvania State College has been assisting the slate industry to solve some of its problems, time and method studies were used in an effort to determine the bottlenecks of production flow. The results are as applicable to other stone industries as they are to slate. A study of the basic elements in the production of roofing slate, structural slate, and slate blackboards among selected slate producers revealed comparatively few refinements. Any marked difference in operating method was characterized largely by the available equipment, a noticeable difference in the working properties of the rock quarried by a particular company, and by either the habit thinking or ingenuity of the individual operators. With the hope that significant economies in manufacture might result, all the unit operations were broken down into elements for study and analysis. The greater part of the study encompassed those operations from the quarry rim to the finished product; however, to obtain a reasonable synthesis of time allotments per operation, several analyses of quarrying from the finish of the wire saw cut are included for reference. The complete study of quarrying made by Bowles several years ago resulted in the introduction of the wire saw into the operation; there appears to be a need for as fundamental a change in the processing of finished slate as the wire saw was in the quarrying process. Fig. 1 illustrates the flowsheet of quarried rock from the parent bed to the quarry rim with the basic elements which contribute to the difficulty of removing slate from the ground. In Pennsylvania roofing slate is produced by one of three procedures, many operations of which are quite similar. In the traditional or classical method the quarried rock is reduced by sculping and auxiliary manual treatment to workable size and then is split and dressed (trimmed to size) in the conventional shanty. Archaic as this method might appear, there are several elements that result in substantial savings over more mechanized operations. In a modified version of this method, the block is reduced by sawing and gouging preparatory to splitting and dressing in indoor stations. This method is particularly adaptable to rock which fractures unevenly by conventional sculping methods. In the third and more modern method, reduced block received from the block maker is diamond-sawed to length and finished on a production line. Fig. 2 illustrates the flow pattern in each case. In the modified and more modern plans, dressing is done on mechanically-operated trimming machines, which appreciably reduce the fatigue factor of the operator. However, it should be noted that it is advantageous for the operator to be able to control the speed of the knife to prevent breakage of certain classes of stock. In the classical plan the splitter and dresser normally act as blockmakers also and carry their eighter slabs (equivalent in thickness to eight shingles) into the shanties themselves, all of which adds to fatigue and reduced efficiency. The extremely low investment and operating expense of the classical method has undoubtedly been of paramount importance in its continuation. Production of Mill Stock The production of mill stock is accomplished by less picturesque methods than enter into the production of roofing slate but it is, in the main, relatively more efficient because of the increased use of machinery for handling and for finishing. Mill stock can be classified into two categories as far as difference in production method is concerned: structural slate and blackboards. The significant difference in operation is caused largely by the nature of the rock used for each product with the best and easiest cleaved rock being reserved for blackboards to permit the splitting of large slabs to as little as 1/2 in. in thickness. Structural stock, on the other hand, is split into panels no thinner than 11/2 in. and

Jan 1, 1952

By M. L. Brashears

IN the last 15 years industrial use of ground water has more than doubled, and in 1951 amounted to 5 billion gallons per day. A similar sharp increase in the utilization of ground water for irrigation and public-water supply occurred in the same period. In many areas rapid increase in withdrawal from wells has taken place almost entirely unhampered by regulatory control and with little or no integration of effort. As might be expected, the chief interest in many regions has been maximum production rather than sustained perennial yield. As a result, widespread depletion of underground reservoirs and deterioration of the quality of the water stored in them has taken place in many areas, even though total pumpage in the United States is far below ultimate potential. Of even more concern is the fact that excessive withdrawal has drawn salt water into the reservoirs beneath many heavily populated centers along the Atlantic, Gulf, and Pacific coasts, causing costly abandonment of pumping plants.' Many hydrologists expect that consumption of water will rise rapidly in the near future, and some predict that industrial requirements will more than double in the next decade.2,3 Thus it appears likely that the draft on many already heavily pumped underground reservoirs will be greatly increased and the search for additional sources of usable ground water intensified in years to come. In view of this, industry as a whole will be forced more and more to recognize the potentialities and limitations of ground-water reservoirs and to utilize them more effectively to prevent costly water shortages and disruption of production. Through painful experience, some industries are already well aware of the need for effective water utilization, and have managed individually or through joint effort to check trends threatening to deplete underground reservoirs completely or to impair the quality of the water. Various remedial measures have been used to bring about successful management of local or regional ground-water resources. Of these, replen-ishment of aquifers by recharge wells or basins has played an important role in overcoming some ground water problems. Artificial recharge of underground reservoirs by water spreading has been practiced successfully in the United States for many years. In the West it has become an important method of salvaging flood run-off for irrigation of crops and maintenance of public water-supply reserves, and it is used to some extent in parts of the East. Artificial recharge by means of wells, on the other hand, is a relatively new development. Until recently it was employed in only a few areas, principally along the East coast. For the last few years, in the ever increasing search for additional water supplies, industry has had greater recourse to this method. Utilization of recharge wells to control the temperature and quality of underground water supplies is also being considered seriously. Operation of recharge wells, like water spreading, is governed largely by local conditions. It requires water relatively low in turbidity, whereas in some areas water spreading has been used successfully with water of high turbidity and silt content. However, water spreading must be employed in large areas and can be carried on effectively only where aquifers crop out at the surface. Recharge wells can be used in limited space. Recharge wells are similar to production wells except that the water flows in the opposite direction. Thus any water-bearing bed that will yield water to wells may be recharged by wells. Often, however, the water available for recharge is of a different character and temperature from that existing in the ground-water reservoir and if transmitted directly underground from a recharge well to a production well might require expensive or difficult treatment before it could be used. Fortunately the physical characteristics of reservoir beds, which control the movement and behavior of ground water, are generally not homogeneous. Moreover, the movement of ground water is very slow because of the frictional resistance of the reservoir beds. By taking full advantage of hydrologic and geologic conditions, it is therefore possible in many instances to bring about favorable changes of temperature and dilution as the water moves from the recharge wells underground to the production wells. Furthermore, if the natural quality or temperature of ground water is unfavorable for industrial purposes, recharge wells may be used to introduce water of more favorable quality or temperature into the ground-water reservoir. When water is discharged into a recharge well, the head in the well is increased. Because of this, a cone of elevation is produced on the water table or the artesian pressure surface in the area surrounding the well. The cone of elevation is similar to the cone of depression produced around a pumping well except that the apex of the cone is above the water table or artesian pressure surface. Thus if a recharge well and a production well tapping the same water-bearing bed are close together, as would be the case at many industrial plants, some of the water discharged from the recharge well would be drawn into the production well within a short time. Under such conditions it is apparent that water of unfavorable temperature and chemical characteristics should not be used for recharging. The more important ground-water reservoirs in the United States often consist of alternating layers of impermeable beds and porous material that will yield water readily to wells. Physical characteristics of individual beds in a ground-water reservoir may not persist over great distances, the impermeable layers grading into beds that will yield large quantities of water. Thus the water-yielding material in underground reservoirs, whether large or small,

Jan 1, 1954

By F. R. Hutto Jr., F. L. Kady Jr., L. E. Weymouth

The behavior of particulate non-metallic materials in moving contact with smooth surfaces is of interest and concern to manufacturers and users of abrasives, of fillers, and of pigments alike. The theoretical aspects of the subject have been treated to considerable extent in the literature, and correlatic,ns are available that attempt to relate various methods of hardness determination." 2 The particle size and friability are characteristics of the abrasive that are not related to the smooth surface. The hardness, on the other hand, may be visualized as relative to that of the smooth surface. In a study of abrasive action, the role that hardness, per se, plays is a complicated one. For it is necessary to compare the "hardness" of the abrasive, usually a non-metallic, with that of the smooth surface, generally a metal. Hardness of non-metallics is defined as resistance to scratch and is almost universally described with respect to the Mohs scale.3 Minerals have been rated by Mohs numerically from the softest (talc = 1) to the hardest (diamond = 10). By definition, a mineral has a designated hardness when it is scratched by the standard that is numerically just above it on the scale; and conversely, when it scratches the standard that is just below it. Hardness of metals. however.. implies resistance to indentation, a property that has been measured by a number of methods. In fact, the indentation hardnesses of the standard minerals on the hlohs scale have been determined by the Rockwell tester. Reproduced below are two versions of this correlation. 'A conversion chart, prepared by Wilson Mechanical Instruments Division of American Chain and Cable Co., merely gives the conversion from Rockwell to Knoop hardness. The relation between Knoop indentation hardness and Mohs scale has been reported by G. S. Smith — A New Scale of Hardness, The Engineer, Aug. 26. 1949. G. F. Kinney in Engineerin Properties and Aplications of Plastics reports the Rockwell hardness of the minerals directly in the Mohs scale. The question immediately arises as to whether this relation is valid when applied in reverse; namely,

Jan 1, 1961

By Jasper L. Stuckey

PYROPHYLLITE, first identified as soapstone,' later as agalmatolite,2 and finally as pyrophyl-lite, has been known to occur in North Carolina for more than 130 years and has been produced intermittently in commercial amounts for the past 100 years. Pyrophyllite mining, however, has become a major industry in North Carolina only during the past 25 years. North Carolina and California are the chief producing states. Current annual production averages 125,000 tons, of which slightly more than 90 pct comes from North Carolina. Distribution and Geologic Setting: All known pyrophyllite deposits in North Carolina are associated with rocks of the Carolina Slate Belt,' which is composed of a vast series of metamorphosed volcanic and sedimentary materials, occurring as two zones extending in a northeast-southwest direction across the state. The larger of these zones, lying in the central Piedmont region, varies from 8 to 50 miles wide. The smaller zone lies along the eastern edge of the Piedmont region and is partly covered by coastal plain sediments. The rocks in both zones consist of a great volcanic-sedimentary series, composed of air-laid and water-laid tuffs and breccias, lava flows, and slates. On the basis of composition, they may be classed into three groups: 1) tuffs, breccias, and lava flows of acid or rhyolitic composition; 2) tuffs, breccias, and lava flows of a basic or andesitic composition; and 3) water-laid slates composed of fine grained materials derived chiefly from the acid tuffs and breccias and

Jan 1, 1959

By J. K. Brooke, F. A. Renninger

During 1966, crushed stone production in the United States totaled just over 811 million tons valued at almost $1.2 billion. This represented in- creases of 4 % in tonnage and 5 % in value over that for 1965. Excluding the crushed stone used for agricultural and certain industrial purposes (cement, lime and flux), crushed stone mineral aggregate production totaled 616.3 million tons valued at almost $910 million, also up roughly 4% in tonnage and 5% in value over the 1965 figures. Limestone was by far the most widely used rock variety, followed by basalt, granite and sandstone in that order. Concrete aggregate and roadstone continued as the main uses for stone, accounting for 63% of all tonnage produced in 1966 and 60% of total stone value. Sand and gravel production in 1966 increased 3% over that for 1965. Total 1966 output was just in excess of 934 million tons valued at almost $985 million as compared with 908 million tons at $957 million for the previous year. Excluding the higher valued industrial sands, 903.2 million tons of sand and gravel valued at $891.6 million were used directly as mineral aggregates, representing a 2.9% increase in tonnage and a 2.4% increase in value over 1965.

Jan 2, 1968

By W. C. Peters, M. W. Pullen, C. A. Bays

During the past three and a half years considerable improvement in the techniques of solution extraction of salt has been made by the use of wells which are cross-connected by hydraulic fracture at the base of the salt. Fracture is initiated by the application of hydraulic pressure. Underreaming and perforating techniques are used to control initiation. The fracture is then extended by continuous pumping until a pressure communication is obtained. Pressure communication is followed by washing-through to obtain a low-pressure connection. Well construction using non-shrinking cements that will bond with the salt and with associated strata is essential to the process. The connecting procedure described permits solution to attack the salt deposit from its base upward, thereby permitting greater recovery, fewer well repairs, better saturation of brine, and overall economy of development and operation. The fracture method of cross-connection requires special pumping of the fluid and is limited by present experience to initial well spacings up to about 1200 feet. The method has been used in bedded salts and is applicable for wells in salt domes. Since spring of 1956, new developnents in salt extraction wells have followed procedures substantially different from those in prior use. Although multiple well systems, connected either by the natural consequence of the solution process or by undercutting under protective pads, have been used previously, the past three and a half years have brought about new designs and new operation procedures based on cross-connection of the wells using hydraulic fracture. To date these techniques have been applied largely in the bedded salt deposits of Michigan, Ontario, Ohio, West Virginia, and New York. To the writers' knowledge they have not been used in salt dome wells. The methods have not yet been in use for a sufficient period to permit any statistical comparison with the older methods. It is evident from experience to date that the methods result in higher recoveries, lower capital and operating costs, better saturation of produced brine, reduced well maintenance and repair, and in considerably fewer production units to insure

Jan 1, 1961

By S. Brunauer

The hydration of portland cement is treated as a chemical reaction and the changes in matter, in energy and the rate of change of the process are discussed, Portland cement is a mixture of four major and at least as many important minor constituents. In the hydration process, the four major compounds (trical-cium silicate, dicalcium silicate, tricalcium alumi-nate and tetracalcium aluminoferrite), plus gypsum and water form five or six new compounds. In spite o the great complexity of the reaction, considerable progress has been made in its understanding, primarily with the help of such research tools as X-ray diffraction and electron microscopy. The rate of the reaction can be followed by direct and indirect methods of measurements. The effects o composition, particle size (or specific surface), temperature and water-cement ratio on the rates of hydration are discussed. The hydration of portland cement is a chemical reaction accompanied by such highly important physical phenomena as heat evolution, setting and hardening. It is a vast and complex subject, on which hundreds of papers have been published. At the time of the writing of this paper, in October 1962, a two-volume book, which alone contains dozens of papers pertaining to cement hydration appeared in print.' The present paper deals with a few aspects of this vast subject, and the selection was not easy. The work reported here deals with some of the most recent investigations in the field. In any chemical reaction, the physical chemist is primarily interested in three things: changes in matter, changes in energy and the rate of change of the process or the speed of the reaction. This is true also of the chemical reaction between portland cement and water, and all three aspects of the reaction will be discussed. These three aspects are of vital interest to the engineer as well. Portland cement is not a cementing material — the hydration products, the new materials which form in the reaction, have the cementing action. The energy changes manifest themselves in a considerable evolution of heat, which may be useful or harmful. It is useful, for example, in winter concreting, but in very large concrete structures like dams, a large evolution of heat, which cannot be easily dissipated, may produce distress in the structure. Primarily for such a purpose was the Type IV or low heat portland cement developed. The speed of the chemical reaction is important because it determines the time of setting and hardening. The initial reaction must be slow enough to permit placing of the concrete before setting occurs. On the other hand, after the placing of concrete it is often highly desirable to obtain as rapid chemical reaction as possible. For this purpose the Type 111 or high early strength portland cement was developed. CHANGES IN MATTER Portland Cement: In a basic investigation, before one begins to study a reaction, one either knows the quantities and compositions of the starting materials, the reactants, or one determines them. This is obvious; the chemist expresses the changes in matter that occur in a reaction by a chemical equation, which has the quantities and compositions of the reactants on the left side of the equation and the quantities and compositions of the reaction products on the right side. The first question is then what to put on the left side of the equation in the reaction between portland cement and water? It is not very easy to answer this question. Portland cement is not a single chemical compound but a mixture of many compounds. Four of these are considered the major compounds, and at least four of the minor compounds also play important roles in the hydration reaction. In order to avoid complicating matters, the present discussion will be restricted primarily to the four major compounds, which constitute usually more than 90% of a portland cement. The relative amounts of these compounds vary from cement to cement. Actually not only the amounts but the compositions of these constituents also vary to some extent, but the variation in composition of the individual components will be neglected for simplicity.

Jan 1, 1963

By Leslie C. Richards

The competitive position of producers of industrial minerals depends upon the delivered price of their product. Freight charges are a major factor in the sales to consumers. A comparison of freight rates on movements of limestone and silica rock in the Pacific Northwest shows a wide variance in mills per ton mile for like hauls, thereby favoring some localities over others. Introduction: Sooner or later the potential miner of industrial minerals reaches the conclusion that of the various factors he must consider, the marketing of his product is. the most important. The sooner he realizes this the better, as successful industrial mineral producers .will confirm. Herein lies a difference between i.ndustria1 mineral mining and metal mining. Often in the latter, technical problems of mining or concentrating are equal to or even surpass those of marketing. This is not meant to imply that there are no problems in mining and beneficiation of industrial minerals, but these usually are outweighed by the problem of marketing. Recentlv. an official of a nationally known corporation :i the elecl.ro-metallurgical industry made an industrial mineral survey in the Pacific Northwest. In the course of his investigation he interviewed producers and potential producers of the various industrial minerals scheduled for use in the plant now being constructed in this area. He stated that he was interested in only three factors: namely, (1) Can your product meet our specifications? (2) Are you able to supply our tonnage requirements? and (3) What will be the delivered price? If there are several sources of supply of sufficient grade and tonnage, as is often the case in the Northwest, then the third factor becomes the important and deciding one. While industrial minerals are usually sold f.0.b. cars with the freight being paid by the buyer, it is the delivered and riot the f.0.b. price that determines the competitive position of the producer and his industrial mineral product. Unfortunately for both the consumers and producers of industrial minerals in the Northwest, the sources are generally a considerable distance from the markets. This necessitates long rail hauls, for which transportation charges make up the largest share of the delivered cost and the delivered price of the product. Is it any wonder then, that rail rates play such an important part in the marketing of industrial minerals? In order to sell his product, the producer must be able to deliver to the market at a competitive price. It must be remembered that his largest cost factor is rail transportation, and that he is limited to markets that he can reach competitively. Since the cost of rail transportation is so important, let us compare various freight rates in the Northwest and attempt to determine their influence on marketing. A study of all rates on all industrial minerals transported in this area, is beyond the scope of this paper. For the purposes of comparison, let us consider limestone (broken, crushed, or ground), and silica rock. These are widely used industrial minerals, and are carried by several different rail routes from.the sources of supply to the centers of consumption in the Pacific Northwest. Markets and Sources of Supply: Limestone has a number of uses in western Oregon and Washington. Among them are agricultural lime for the soils of the Willamette Valley and southwestern Washington; paper rock for the mills in such cities as West Linn, Oregon City, Newberg, St. Helens, and Salem, Oregon, and Camas and Everett, Wash.; chemical and metallurgical-grade limestone for the metallurgical plants centering around Portland, and the Tacoma-Seattle areas'; and sugar rock for the sugar refineries at Toppenish, Wash., and Nyssa, Oregon. Since limestone for cement manufacture is generally processed near the quarry, transportation

Jan 1, 1951

By Leslie C. Richards

Sooner or later the potential miner of industrial minerals reaches the conclusion that of the various factors he must consider, the marketing of his product is. the most important. The sooner he realizes this the better, as successful industrial mineral producers .will confirm. Herein lies a difference between i.ndustria1 mineral mining and metal mining. Often in the latter, technical problems of mining or concentrating are equal to or even surpass those of marketing. This is not meant to imply that there are no problems in mining and beneficiation of industrial minerals, but these usually are outweighed by the problem of marketing. Recentlv. an official of a nationally known corporation :i the elecl.ro-metallurgical industry made an industrial mineral survey in the Pacific Northwest. In the course of his investigation he interviewed producers and potential producers of the various industrial minerals scheduled for use in the plant now being constructed in this area. He stated that he was interested in only three factors: namely, (1) Can your product meet our specifications? (2) Are you able to supply our tonnage requirements? and (3) What will be the delivered price? If there are several sources of supply of sufficient grade and tonnage, as is often the case in the Northwest, then the third factor becomes the important and deciding one. While industrial minerals are usually sold f.0.b. cars with the freight being paid by the buyer, it is the delivered and riot the f.0.b. price that determines the competitive position of the producer and his industrial mineral product. Unfortunately for both the consumers and producers of industrial minerals in the Northwest, the sources are generally a considerable distance from the markets. This necessitates long rail hauls, for which transportation charges make up the largest share of the delivered cost and the delivered price of the product. Is it any wonder then, that rail rates play such an important part in the marketing of industrial minerals? In order to sell his product, the producer must be able to deliver to the market at a competitive price. It must be remembered that his largest cost factor is rail transportation, and that he is limited to markets that he can reach competitively. Since the cost of rail transportation is so important, let us compare various freight rates in the Northwest and attempt to determine their influence on marketing. A study of all rates on all industrial minerals transported in this area, is beyond the scope of this paper. For the purposes of comparison, let us consider limestone (broken, crushed, or ground), and silica rock. These are widely used industrial minerals, and are carried by several different rail routes from.the sources of supply to the centers of consumption in the Pacific Northwest. Markets and Sources of Supply: Limestone has a number of uses in western Oregon and Washington. Among them are agricultural lime for the soils of the Willamette Valley and southwestern Washington; paper rock for the mills in such cities as West Linn, Oregon City, Newberg, St. Helens, and Salem, Oregon, and Camas and Everett, Wash.; chemical and metallurgical-grade limestone for the metallurgical plants centering around Portland, and the Tacoma-Seattle areas'; and sugar rock for the sugar refineries at Toppenish, Wash., and Nyssa, Oregon. Since limestone for cement manufacture is generally processed near the quarry, transportation

Jan 1, 1951

By A. E. Chute

The shortage of sulfur is not only continuing but appears to be worsening, attended by steadily rising prices. At the same time emphasis on air-pollution abatement is also increasing. These two factors, a rising market and the growth of environmental attention, have encouraged producers to carefully review all possible sulfur sources. As a result, production of sulfur from hydrogen sulfide occurring in petroleum is receiving greater attention than ever before. Until about a decade ago, the practice of recovering sulfur from hydrogen sulfide separated from gases (either found naturally or generated in desulfurization of liquid petroleum) was wide1y recognized but contributed little to total free-world sulfur production. However, during the past ten years, the production of sulfur from this source has increased so rapidly that it now accounts for a substantial portion of total production. This trend shows no signs of slackening, and current forecasts predict that recovered sulfur may become the dominant source of supply within ten years, exceeding mined sulfur production. This paper is intended to list sulfur sources and relationships, and to discuss the potential of producing sulfur from petroleum. The processing involved, in addition to product storage and transportation will also be discussed along with important economic aspects of sulfur recovered from hydrogen sulfide. For many years, most of the world's elemental sulfur has been produced from salt domes, predominantly by the Frasch process. During the past decade, however, another production source has developed so quickly that it is expected to surpass the Frasch production sources within a short time. This new source lies in the petroleum gases and liquids from which dramatically increasing quantities of elemental sulfur are being recovered. In the phraseology of the trade, the sulfur so obtained is know as "recovered sulfur," a term which does not, as one might expect, include sulfur recovered from other sources such as smelter gases. The growth rate of recovered sulfur compared to that of Frasch sulfur, total elemental sulfur, and total Free World sulfur in all forms is shown in Fig. 1 Since 1963, sulfur consumption has exceeded production,with the natural result that the price of sulfurhas continually increased. The posted price reported for f.o.b. Port Sulphur, La., has risen from as low as $18 per ton in 1962 to $32.50 per ton in mid-1967. With freight and other charges, delivered prices have of course run much higher, amounting to $45 or $46 per ton on the east and west coasts. In some cases, spot sales for as much as $60 have been reported. Although it is playing an ever-increasing role in the sulfur market, recovered sulfur was originally a by-product of the removal of hydrogen sulfide from natural and petroleum refinery gases. Today, however, it is often the most valuable product of a multi-product processing facility. Since there are two major sources of recovered sulfur—production and refining processes —natural gas is included with liquid petroleum for purposes of this discussion. Sulfur from these sources is produced in the form of gaseous hydrogen sulfide which is removed from a gas stream and converted to elemental sulfur. Gases in which hydrogen sulfide occurs naturally are natural gas and the gas produced from a high=pres-sure crude=oil or condensate field.

Jan 1, 1969

By C. O. Lee, Z. W. Bartlett, R. H. Feierabend

The Grand Isle sulfur mine is located in the Gulf of Mexico, approximately seven miles off the coast of Grand Isle, Jefferson Parish, La. The deposit is on acreage covered by oil, gas, and mineral leases originally issued in favor of Humble Oil & Refining Co. by the State of Louisiana which were continued, maintained, and redesignated by the U.S. Department of the Interior after passage of the Outer Continental Shelf Lands Act. The sulfur deposit was discovered in 1949 when Humble Oil & Refining Co. penetrated more than 200 ft of sulfur-bearing limestone in a zone between 1813 and 2075 ft below sea level. In 1954, Humble drilled ten more sulfur prospect holes, eight of which encountered sulfur ore. On September 19, 1956, Freeport Sulphur Co. acquired from Humble Oil & Refining Co, the sulfur rights underlying the tracts, and the actual design of the installation began the same month. The first structural contract was awarded in December 1957 and offshore erection began in June 1958. The initial phase of construction has been completed and production by the Frasch process commenced in April 1960. The estimated total cost of the project is $30 million, of which $8 million is the extra cost incurred by the necessity of offshore operations. More than $22 million was expended before production was started. GEOLOGY OF DEPOSIT Grand Isle is the third largest sulfur deposit in the U.S. The orebody embraces several hundred acres, but its outer limits are yet to be defined to the northeast, east, and south. Most Gulf Coast sulfur deposits occur in a caprock mantle of calcite (referred to as limestone), anhydrite, and occasionally gypsum, which covers the apex of an intrusive mass of salt. Commercial quantities of sulfur are usually confined to the calcite or limestone member. Most often such limestone is completely enclosed by dense anhydrite below and impervious sediments above, which effectively form a closed reservoir. The depth of the Grand Isle orebody ranges from 1800 ft to 2500 ft below sea level. Within the present boundary, the sulfur-bearing limestone varies in thickness from 220 ft to 425 ft, while the sulfur content varies an average of about 15 pct in the leanest hole to an average of about 30 pct in the richest. Rock containing less than 5 pct sulfur is not classed as ore, and holes assaying less than 20,-000 long tons per acre of sulfur in place are not considered commercial offshore. The sulfur enrich-

Jan 1, 1961

By W. A. Hutchins

Water laws important to the mining industry are those which govern or affect the right to use water, to dispose of water after using it in mining or milling, and to discharge waste material into watercourses. They include statutes and court decisions having general applicability, as well as others that pertain specifically to mining. THE INDUSTRY'S CONTRIBUTION TO WESTERN WATER LAW Despite sharp differences of opinion, the water law the Spaniards brought to the Southwest appears to have included some form of appropriation of water. The Mormons, who settled in Utah in the mid-nineteenth century, also developed a system of appro-priative water titles. But by far the most profound impact on western water law was made by the gold-seekers who flocked to the Sierra Nevada foothills of California after the discovery of gold in 1848. Much of the gold was extracted from the ground by hydraulic or placer mining, and so the miners' rights to the use of water became fundamentally important. Since there was no organized government in the foothills and no laws other than those made by the miners, they helped themselves to the land, the gold, and the water needed to work their claims.1 They established and enforced regulations governing the acquirement and holding of mining claims and their rights to the water they needed.' In 1879 Justice Field, former Chief Justice of the California Supreme Court, spoke for the U. S. Supreme Court in saying that the miners were "emphatically the law-makers, as respects mining, upon the public lands in the State."" Rules of the California mining camps were based on two essential principles: 1) priority in discovering claims and appropriating water by diverting it from streams and putting it to use, and 2) diligence in working claims and applying water in mining. The customs so developed, which were copied in mining areas of other states and territories, were enacted into law in one western jurisdiction after another. They form the basis of what is called the arid-region doctrine of prior appropriation of water, which received the attention of Congress in legislation recognizing and protecting appropriations of water for mining, agriculture, and other purposes on the public domain.' In several western states a great number of water cases decided in the early years involved relative rights to the use of water for mining purposes or for milling connected with mining." The miner's inch, the customary unit for measuring water in the mining camps, is still used in various western communities, although its relation to the cubic foot per second varies from one area to another. Undoubtedly, the miners of a century ago made the major contribution to the appropriation doctrine as it is now recognized and applied throughout the West. What inspired the California gold-seekers to develop these principles? Thoughtful writers have pointed out that their regulations and customs were strikingly characteristic of much earlier mining enterprises in the Old World.D It is said that the right of free mining and free use of flowing water therefor —so similar to the California conditions and practices—-was a part of the customs of Germanic miners in the Middle Ages, that it spread from middle Europe to other countries and colonies, and that the doctrine of prior appropriation was widespread in the important mining regions of the world. Certainly the Forty-niners came to California from many countries. It does not tax the imagination to consider that they may have brought with them some knowledge of the old Germanic customs and applied this knowledge in their new environment. RIGHTS TO USE OF WATER IN GENERAL In the West, rights to the use of water of watercourses fall into two categories—appropriative and riparian. The doctrine of prior appropriation is recognized in each of the 17 western states. The riparian doctrine is recognized concurrently with the appropriation doctrine in some of these states but has been abrogated in the others. The riparian doctrine prevails generally throughout the East, although there is now considerable interest in developing something else. Generally speaking, the appropriation doctrine has been highly developed in the West, whereas the principles of riparian doctrine have been comprehensively established in only a few states throughout the country. The subject of water rights is a big one. Space permits no more than a brief discussion of aspects that bear upon the title of this article. RIGHTS OF PRIOR APPROPRIATION Fundamental to the doctrine of prior appropriation is the principle first in time, first in right. Although in some states there are statutory exceptions. the original and still generally prevailing rule is that the first one who initiates a right to divert and use water of a stream, and who completes his undertaking with reasonable diligence, acquires thereby the first right of appropriation of the specific quantity of water involved. Each succeeding right in point of time is junior to all earlier rights but senior to all later ones. The practical effect of this priority system is that when the water supply is not enough for all, the earliest rights must be fully satisfied before any water may be taken by those later in time. Acquirement of Appropriative Rights: Each of the 17 western states has a statute under which water may be appropriated pursuant to a prescribed procedure. Generally, the first step to be taken by the intending appropriator is to file application in the office of the State Engineer for a permit to make the appropriation. In most but not a11 states, valid ap-

Jan 1, 1961

By K. N. Weaver

In the early 1950's the cement industry began putting a new emphasis on geology. This article points up some of the industry's raw materials problems that geologists are uniquely qualified to handle. Portland cement can be made from relatively abundant industrial minerals and rocks, and this may explain why cement producers placed little emphasis on geology during the early days of the industry. After World War 11, however, the industry began to recognize the need for geological exploration and some of the larger companies began to build a permanent geological staff. This development has its roots in: 1) The rapid expansion of the industry. After World War II and continuing into the early 1950's the demand for cement far exceeded the production capacity. This placed a great deal of pressure on the producers to enlarge capacity at their plants and to develop new sites. 2) The closing of many cement plants due to inadequate raw materials. Producers feared lack of raw materials due to inadequate exploration and evaluation. 3) An ever increasing pressure for upgrading of the quality of portland cement, necessitated upgrading the quality of raw materials. 4) The increasingly large capital investment needed to build new cement plants required a higher degree of accuracy in reserve calculation. These reasons are more or less self explanatory and will not be elaborated on. They are outlined to illustrate the probable evolution of thought among cement management to justify the development of a geological staff. In the author's personal experience the geologist must continually readjust to changing conditions within the industry. For example, cement production capacity grew so rapidly that today production is only about 70% to 75% of rated capacity (73.8% in 1963). Therefore, whereas the geologist's function during the active expansion of capacity was primarily one of exploration, one of his major functions today is the development of existing reserves. This assumes of course that reserves at existing plants have been proven to be adequate in terms of the company's reserve policy. Through the proper development of raw materials, the geologist can markedly influence quality control, production and long range planning. Examples of several of the operations of Medusa Portland Cement Co. will illustrate how proper attention to geologic detail pays off in the above areas. Because limestone is the major raw material of port-land cement, the examples will be concerned with it. DEVELOPMENT OF GEOLOGIC DETAIL One of the prime objectives of an exploration or development project should be the establishment of the stratigraphy and structure of the deposit. The basic tool for exploration and development is still the core drill, and the geologist must gain a maximum amount of information from a minimum amount of drilling. In order to obtain this objective the following is essential: 1) Adequate detailed geologic logging of cores. The core is first logged and separated into lithologically distinct units. In order to make the lithologic breaks as meaningful as possible, representative pieces of core (not all) are etched in dilute HCI. This removes the "drill polish", brings out the structure of the rock and indicates the proportion of dolomite and argillaceous material because dolomite and argillaceous material etch in relief. In this way the lithologic breaks become clearer and one gains a general idea of the chemical makeup before analysis. This method of logging lessens the probability of including two types of stone, e.g. limestone and dolomite into the same sample for chemical analysis. 2) Representative sampling for chemical analysis. After logging, the lithologic units are sampled for chemical analysis. A representative analysis can be obtained by extracting a 1-in. sample for every foot of core. For example, a lithologic interval of 10 ft to 20 ft would yield ten 1-in. samples taken at 11 ft, 12 ft, 13 ft... and 20 ft. These samples are then crushed, pulverized and split into a sample for chemical analysis. This sampling method represents a significant saving of time over splitting the entire core. 3) Preparing the core as a record. Because of the expense of storage and the difficulty of handling large amounts of core, only representative samples of each lithologic unit are saved for reference. An

Jan 1, 1965

By R. J. Anderson, A. V. Castelli

In 1986, United States' barite production fell 48.9%, consumption - sold or used by grinding plants - was off 47.3%, and imports were down 63.8%. Meanwhile, world mine production decreased 29.6%, according to the US Bureau of Mines. However, value of US-produced barite FOB mine increased 46.51%, according to USBM figures. The declared value CIF US port of all imported unground barite decreased from $41.94/t ($46.23 per st) to $39.02/t ($43.01 per st). Nevada continued to be the leading US producer of barite with 69% of the total. It is followed by Georgia, Missouri, Tennessee, and California. The USBM estimates that 65% of the barite mined was used as a weighting agent in drilling fluids. The remaining 35% was used in the production of barium chemicals and as a filler. Most of the production from Missouri, Georgia, and Tennessee was used in the non-oilfield sector. This sector made up a larger percentage of the US produced barite in 1987 than it did in 1986, increasing the overall value per ton of barite. Barite consumption was at its lowest since 1963. It is estimated that 80% of the barite was consumed in the drilling fluid market. The remaining 20% was used in barium chemicals, glass, and as filler in plastics and paper. The decline of barite used in drilling fluid followed the decline in the average number rotary rigs operating - 964 versus 1968 in 1985. This was the lowest average number of rotary rigs operating since 1971. The non-oilfield market was up 5.3% in 1986. This increase can be attributed to the increased use as a filler in plastics. Imports of crude barite, though down nearly two-thirds, still made up 65% of the barite consumed in the US. China was the leading exporter to the US with 58%, followed by India, 15.4%; Morocco, 11%; Thailand, 5.4%; Mexico, 4.6%; Chile, 3.9%; and Ireland, 1.7%. Less than 1% of the imported ore was used in the nonoilfield sector. Imports of ground barite dropped from 64.4 kt (71,000 st) to 19.8 kt (21,800 st) in 1986. Of this amount, 14.1 kt (15,500 st) were used in drilling fluids in 1986 and the remainder for non-oilfield use. During 1986, more of the grinding plants supplying the drilling fluid market were closed. Dresser Magcobar and IMCO Services, a Halliburton company, formed M-I Drilling Fluids Co. Mine production in the US will probably decrease in 1987 due to the lower cost of imported ore. No significant change is expected in the drilling fluid market. The average number of operating rotary rigs is estimated at 950 in 1987 versus 965 in 1986. The nondrilling fluid markets (chemicals, glass, and filler) will follow the overall US economy. Bauxite and alumina R. J. Anderson, Ohio State University US bauxite production in 1986 dropped to a pre-World War II level, continuing a decline that began a decade ago. 1986 production totaled 450 kt (496,000 st), compared to 674 kt (743,000 st) in 1985. World production of bauxite also decreased in 1986. This reflected the soft market in alumina, aluminum, and related products. Total mine production worldwide came to 79 Mt (87 million st), down from 85 Mt (94 million st) in 1985. For the sixteenth consecutive year, Australian production of bauxite led all other sources. No other country approached the 28 Mt (31 million st) mined in Australia in 1986, despite a 4.4-Mt (4.9-million st) drop in its output from 1985. Other major producers in 1986 were: Guinea 11 Mt (12 million st), Brazil, 6.5 Mt (7 million st), Jamaica, 6.5 Mt (7 million st), and Suriname 2.8 Mt (3 million st). Despite weakness in world demand for bauxite, Venezuela, heretofore an alumina producer, is now pushing development of a new mining venture near the western border of the state of Bolivar. Plans call for barging bauxite down the Orinoco River to the Ciudad Guyana alumina plant, a distance of 650 km (400 miles).

Jan 5, 1987

By G. Coombs, L. Meade, J. Welshimer

Industrial Minerals commodity profiles are continued from May's Annual Review issue. Diatomite G. Coombs, Manville Sales Corp. Growth in US diatomite production continued to lag in 1986. The US Bureau of Mines estimated that 580 kt (640,000 st) were produced last year. This is a 1%0 growth over 1985. The cumulative growth from the 1982 low point is 4.4%. Present production, though, is still only 90% of the high tonnage of 1979. The industry will see increased competitive activity with the start-ups of two new mines and production facilities in California and Oregon. US production has come primarily from Lompoc, CA, Bassalt, Clark Station, and Lovelock, NV, and Quincy, WA. New production, probably with capacities of 45 kt/a (50,000 stpy) each, have started near Burney, CA, and Vale, OR. Eagle Picher's new, full-line filter aid and filler plant at Celatom, Vale, OR, was dedicated in August. The plant uses diatomite from the Celatom mining district in Juntura, OR. Grefco's new filter aid and filler plant near Burney, CA, was ready in July. It produced flux calcined products through a single kiln and can handle both bag and bulk shipments. The operations are in Shata County with the plant and mine at the same site. Manville Specialties Group is moving its Filtration and Minerals Division headquarters and research staffs to Lompoc, CA. The move is intended to strengthen response and performance by locating research, marketing, and production close together. Diatomite is processed in three methods: natural, calcined, and flux calcined. The natural is dried to remove water and is particle size classified. Calcined or straight calcined products have been sintered to modify particle size or permeability. Flux calcination, or flux sintering, has a stronger influence on permeability and also benefits color. The unique structure of diatomite is used in a range of particle sizes from fine paint fillers, to coarser filter aids, to granular aggregates. Dimension stone L. Meade, Geomapping Associates Ltd. 1986 was another good year for dimension stone production. The trend toward using marble, granite, limestone, sandstone, and slate has created an increasing demand. According to US Bureau of Mines 1986 estimates, 1.1 Mt (1.2 million st) of dimension stone, with a value of $173 million, was produced by 200 companies. This is an increase from 1985, where 220 companies produced 1 Mt (1.12 million st) valued at $172 million. The increased production volume and decreased unit value is due to the competition from imports. The net import reliance in 1986 was 68% compared to 62% in 1985. The value of imports was $374 million in 1986 versus $295 million the year before. In an effort to maintain their market share, domestic finishers, particularly in the granite industry, continued to upgrade plants and machinery during 1986. In addition, offshore dollars have financed a number of fabricating facilities in North America that will finish imported rough stock. It is hoped that this increased domestic production capability will capitalize on a devalued US dollar. The trend has been for growth in stone usage and market. This trend is continuing with increased public awareness and desire for natural stone in buildings. The area of greatest market growth is expected to be in residential and interior decorative stone usage. Use of sophisticated, automated equipment has made the cost more affordable. Now lobbies, foyers, and specialty rooms are being clad in stone. Dolomite J. Welshimer, National Lime & Stone Co. About three-quarters of dolomite production is used as construction aggregates and 10% to 20% is sold or used as an industrial mineral. Total limestone and dolomite consumed for chemical and metallurgical purposes is about 136 Mt/a (150 million stpy). Sales of industrial dolomitic products were somewhat stronger in 1986 than levels recorded in the early 1980s. Some of the sales' strength, however, can be attributed to reductions in the number of active mining and processing operations. The industry will probably undergo further consolidation by the end of this decade. This will be due primarily to the continued softening in demand by the steel industry. Dolomitic limestone deposits being mined for raw materials for the steel, glass, and refractory in¬dustries are generally 54% calcium carbonate and 45% magnesium carbonate by weight. Impurities composed of silicon, aluminum, iron, sulfur, and phosphorous, represent less than 1%. The heaviest concentration of high purity, surface mineable dolomite in the US is in northwestern Ohio. Crushed and sized dolomitic limestone is a basic raw material for the iron and steel industry. It is also used as feed stone or lime kilns. Soft-burned lime is a popular raw material for BOF steel production. It is also used extensively in insulating glass fiber manufacturing. A related material, hydrated

Jan 6, 1987

By L Baumgardner, A. V. Castelli

Barite In 1987, United States mine production of barite increased 15.870, consumption (sold or used by grinding plants) increased by 6.97, and imports are estimated to have fallen by 19.57. World mine production decreased by 137, according to the US Bureau of Mines. The value of US produced barite, fob mine, decreased 1.4%, according to the Bureau. The declared value for cif US port of all imported unground barite during the first 10 months of 1987 decreased from $39.02/t ($35.40 per st) to $37.16/t ($33.71 per st), the Bureau stated. Nevada continued to be the leading US producer of' barite with 637r of the total. It is followed by Georgia, Missouri, California, Tennessee, and Montana. The Bureau of Mines estimates 657 of the US mine production was used as a weighting agent in drilling fluids. The remaining 35°/r was used in barium chemicals, glass or as a filler. Most of the production from Missouri, Georgia, and Tennessee was used in the non-oilfield sector. This sector continued to increase. Of the total consumption (used by grinding plants and chemical manufacturers), it is estimated that 8070 was used in drilling fluids and 2017( in the non-oilfield sector - barium chemicals and fillers in paper, plastics, and glass. The tonnage consumed in the drilling fluids market increased slightly. But the average number of rotary rigs operating decreased from 964 in 1986 to 936 in 1987. This is the lowest number of operating rigs reported since 1949. The increase in consumption in this sector is due to an increase of rigs operating in the US Gulf and other higher consumption areas over 1986. Crude barite imports were estimated to be down by 19.5% in 1987. Still, they accounted for 637 of the barite consumed in the US. During the first 10 months, China continued to be the leading exporter to the US with 86.970, followed by Mexico with 10.997, and Morocco 2.107(. About 5Y of the imported ore was used in the nonoilfield sector. Ground barite imports dropped from 19.8 kt to 8.8 kt (21,800 st to 9800 st) in 1987. Of this amount, 1.4 kt (1598 st) was used in drilling muds and the remainder of the non-oilfield use. During 1987, a few more grinding plants that supplied the drilling fluid market were closed. Along the US Gulf Coast, there are 13 operating plants versus a high of 31 in 1981. Cameron Offshore reopened its grinding plant at Cameron, LA. New Riverside Ochre Co. of Cartersville, GA, purchased a jigging-washing plant in Missouri and plans to place it in operation this year on a new deposit near Cartersville, GA. Milpark purchased Hughes Drilling Fluid in 1987 and operates under Milpark. US mine production will probably stay about the same as 1987. Price increases in the 10 % range for imported ore are expected due to water freight and the weak dollar. Baker Hughes estimates the average number of operating rotary rigs at 1070. A slight increase is expected in the non-drilling fluid market (chemicals, glass, and filler). Bauxite and alumina L. Baumgardner, US Bureau of Mines Domestic bauxite production in 1987, expressed as dried equivalent, was 581 kt (640,400 st), a 14% increase over 1986. US mine production amounted to less than 170 of total world production. Virtually none of the domestic bauxite was consumed in the production of primary alumina metal. About 30% of the bauxite produced by US mines was calcined to produce 117 kt (128,970 st) for use in abrasives, catalysts, chemicals, proppants, and refractories. Most of the uncalcined bauxite was refined to specialty aluminum oxide (alumina) forms. Metallurgical grade bauxite was imported from 10 countries in 1987. Principal suppliers of the 9.8 Mt (10.8 million st) were Guinea (4270), Jamaica (3501,), Australia (127), and Brazil (57). The average value, delivered U.S. ports, cif, as reported to US Customs Service, was $29.50/t ($26.76 per st). Calcined refractory grade baux-

Jan 6, 1988

In 1992, United States mine production of barite decreased 8.5%. Barite consumption, sold or used by grinding plants, decreased by 36.9% and imports decreased by 61.6% vs. 1991. World mine production decreased 1.5%, according to the US Bureau of Mines. The value of domestically produced barite, f.o.b. mine, decreased 11.9% according to the Bureau. The declared value, c.i.f. United States port, of all imported crude barite during 1992 decreased from $42.35/t ($38.42/st) in 1991 to $40.09/t ($36.37/st). Nevada continued to be the leading producer of barite with 88% of the total, followed by Georgia and Missouri. It is estimated that 80% of the domestically mined barite was used as a weighting agent in drilling fluids. The remaining 20% was used in barium chemicals, glass or as a filler. Most of the production from Missouri, Georgia and Ten¬nessee was used in the non-oilfield sector. Of the total barite used by grinding plants and chemical manufacturers, it is estimated that 90% was used in drilling fluids and 10% in the non-oilfield sector. This included barium chemicals and fillers in paper, plastics and glass. The tonnage consumed in the drilling fluids market decreased due to the lower average rig count during 1992. The average number of rotary rigs operating (717) was 16.6% less than the 1991 average of 860 in the United States. Crude barite imports were 518 kt (571,000 st), 61.6% less than in 1991. Imports accounted for 44.7% of the barite consumed (apparent) in the United States. During the year, China continued to be the leading exporter of crude barite ore to the United States with 67.2% of total crude ore imports. India followed with 31 %, and others with 1.8%. About 90% of the imported barite ore was used in the oilfield sector. Ground barite imports decreased from 46.3 kt (51,000 st) to 30.9 kt (34,100

Jan 1, 1993

The United States continued to depend on imported bauxite during 1995. Domestic bauxite mine production remained at about the same level as in 1994. It amounted to less than 1% of total world production. All of it was used for nonmetallurgical products, such as abrasives, chemicals, proppants and refractories. Metallurgical grade bauxite was imported from 12 countries. Principal suppliers for this 10 Mt (11.1 million st) of ore were Guinea (39%), Jamaica (35%), Brazil (17%) and Guyana (8%). The average value of imports, c.i.f. US ports, was $31/t ($28/st). Calcined refractory-grade bauxite imports totaled235 kt (259,000 st). It had an average value of $112/t($102/st) c.i.f. US ports. China supplied 61%, Guyana30%, Hong Kong 4% and France 3%. Imports of other grades of calcined bauxite, primarily for the abrasives market, totaled 259 kt (286,000 st).They were supplied by China (59%), Greece (20%), Brazil (14%) and Australia (6%). The average value was$74/t ($67/st) c.i.f. US ports.

Jan 1, 1996

Editor’s note: As usual, the June issue features an industrial minerals review. And some thanks are in order. Thank you to the industrial minerals annual-review editor, to the technical committees chair and vice chairs and to the authors of the individual commodity profiles. Jim Norman of GeoTrans Inc. is the industrial minerals annual-review editor. Lucy McCartan, US Geological Survey, was the chair of the SME industrial minerals technical committees. She also served as the vice chair for agricultural minerals. Other technical committee vice chairs were: •Gary Tomaino, Specialty Minerals Inc., ceramics and refractory materials. •Srinivas (Vas) Veeramasuneni, US Gypsum, chemical raw materials. •William Langer, US Geological Survey, construction materials. •Vanessa Santos, Independent, fillers and pigments. •Richard Berg, Montana College of Mineral Science and Technology, specialty minerals. Their help makes possible this June industrial minerals issue. On behalf of the readers, the editors thank them.

Jan 1, 2002