Search Documents

By Irwan S. Halim

For tunnels in horizontally bedded rock, geologic factors affect the selection and design of the initial supports, including the rock propensity toward parting along bedding and the resulting high potential for rock slabbing during excavation. To evaluate this ground behavior, numerical analyses and results with Mohr-Coulomb, Hoek-Brown, and Ubiquitous Joint constitutive models were used, using the Upper Rouge CSO tunnel in Detroit, Michigan as an example. The different rock models and other geologic considerations are shown to impact the selection of the tunnel initial support and design. This paper emphasizes the appropriate selection of an analytical model based on the site specific geology to achieve an optimum initial support design.

Jan 1, 2008

The rapid industrialisation of the world was driven by an improved ability to utilise chemical energy. Unfortunately harnessing explosive energy did not come cheaply given the hundreds of lost lives. However, the modem explosives industry has made significant technological achievements, for explosives are now considered to be both safe and extremely effective. Upon closer inspection, it would appear the key to this achievement has been the development of initiation systems. While the focus may have been originally on safety, modem developments have concentrated upon harnessing the benefits of initiation control. Before attempting to gaze into the future, it is worth reviewing some of the significant advances that have occurred.

Jan 1, 1990

By Erik Olsson, Gunilla Hyllander, Stefan Schuster, Lena Sundqvist Ökvist, Maria Lundgren, Michael Hensmann, Olavi Antila

"Residual materials from the integrated steel plant itself or other sources often contain valuable compounds of e.g. C and Fe. Dust and sludge have to be agglomerated to be able to recycle to the blast furnace (BF) via top-charging. By injection of the materials, preparation methods in terms of e.g. drying and/or screening only, can be used. Alternative carbon materials (ACM) in terms of BF dust and sludge have been successfully injected up to levels of 60 kg/tHM in the LK.AB Experimental Blast Furnace (LKAB EBF®). Efficiency in recovery of valuable compounds as well as the behavior of undesired elements have been evaluated and are discussed.IntroductionTraditionally, recycling of steel in-plant fines is made via the sinter plant and blast furnace route. Steel plants operating with 100% pellet as ferrous burden and have no sinter plant. There are limited areas for land fill and costs are caused for preparation of landfills and deposit fees. Very fine paniculate dusts or sludges cause decreased productivity and increased coke rate in the sinter plant, and therefore other ways for recycling must be considered. Injecting them into the BF could be an economically and technically feasible alternative. Additionally, as the materials contain valuable compounds of e.g. C and Fe."

Jan 1, 2012

By Robert F. Randolph

Introduction This paper is a descriptive analysis of injuries and fatalities at small surface bituminous coalmining companies in Pennsylvania. The purpose of analyzing a specific industry sector and location is to identify issues that might be missed in a wider analysis. Other studies of small mine safety (e.g., Peters and Fotta, 1994, Randolph and Boldt, 1997) have shown that the relationship between safety and mine size is not a simple one. Some injury types occur at higher rates at small mines, while others occur at lower rates. Consequently, an analysis limited to a specific type of mining can help identify hazards and issues specific to that sector. The results of this analysis will be useful for directing training, intervention, and research efforts towards the most prevalent causal factors and incident types. Procedures and Definitions Data sources The primary sources of data for this analysis were files provided by MSHA containing information collected under Title 30 Code of Federal Regulations, Part 50. These files, commonly referred to as “Part 50 data”, are provided though MSHA’s Program Evaluation and Information Resources directorate. Two primary types of injuries were selected from the Part 50data: Fatalities (MSHA “degree of injury” code 1) and lost-time injuries, otherwise known as nonfatal with days lost (MSHA “degree of injury” codes 2 through 5). Lost-time injuries involve either actual days away from work or days of restricted activity or both. Fatality and lost-time injury incidence rates were calculated using the standard MSHA formula: Number of injuries per 200,000 employee-hours. Additional information on company sizes and mine ownership was provided by the Pennsylvania State University College of Earth and Mineral Sciences. Time span A five-year time span was selected for this study. More than a single year of safety experience is usually needed to capture a broad range of incident types. Many types of injuries, especially fatal injuries, can be extremely rare, and may be missed if too short a time span is selected. However, a time span that extends too far back may begin to suffer historical threats to validity. That is, incidents that occurred several years ago may be caused by hazards that have since been remedied or may be related to mining practices and conditions that no longer exist. A five-year span offers a practical compromise between these two concerns. Consequently, the MSHA Part 50 data files from 1993 through 1997 were used. The 1997 file was in “preliminary” form at the time of the study, so small variations from the final 1997 “close out” file can be expected. Based on past experience, we do not expect the close-out variations to have a significant impact on the findings.

By S. T. Reese

STATISTICS of injuries in the quarrying and related industries in the United States first became available when the Bureau of Mines collected reports from the operating companies for the calendar year 1911. Since then reports have been collected annually. The present bulletin, covering the calendar year 1952, is the 33d publication containing statistical data on injuries at quarries and related plants, and it is the first to be published since 1944. The last publication was Bulletin 458, Quarry Accidents in the United States during the Calendar Year 1942. The unpublished statistics for 1942-51 may be found in the Appendix of this bulletin. The Bureau of Mines is authorized to collect data on injuries at quarries, but there is no Federal law that compels operators to supply such data, and the reports received from operators are voluntary responses to the Bureau's requests for information. Although the figures presented herein may not be complete for the entire industry, every effort has been exerted to make them so, and the figures given are believed to be thoroughly representative of the hazards to which quarry workers are exposed. Moreover, the figures are com¬parable as between States -which is significant in view of the lack of uniformity among the States as regards classes of plants covered by State laws, classes of injuries covered by State reports, and other factors that tend to make it impracticable or impossible to compare the injury experience of one State with that of another or to comprehend the relative importance of the various causes of injuries in the industry as a whole.

Jan 1, 1955

By D. E. Poole

Injury Prevention: Dependent, Independent and Interdependent In recent years, management-directed (dependent)safety programs have lost ground to the more successful self-directed (independent) programs, where employees take responsibility for their own safety. Today, with the growth of the team concept in industry, a mutual-caring (interdependent) approach to workplace safety is gaining wide acceptance. This presentation compares characteristics and results of the three progressive levels of safety responsibility and explains how to develop a successful interdependent program. The presentation will also detail the common principals that are necessary for safety excellence under any of the management styles.

Jan 1, 2000

By Samuel A. Reipas

Introduction The ore mining industry has been successful because of technological progress and huge sums of capital investment. But new technology and plants have not come cheap. The problem now is companies will run out of money before they run out of ideas. Survival Strategies Industry survival strategies demand restructuring and new plans. Inland's prescription for the future includes: • Continued emphasis on technological improvements to upgrade pellet quality and lower costs; • Effective use of human resources resulting in employee satisfaction and improved planning and productivity; • Deliberate, well planned, and documented cost-control programs for the short- and long-term; and • Capital investments to support the first three initiatives. Technology Technological changes are not only required by the need for operational improvements, but by product quality improvement dictated by the user - usually the blast furnace operator. Established ambient measurements of pellet quality, such as tumble index, compression strength, porosity, size distribution, and chemical composition, are no longer considered meaningful in predicting pellet performance in a blast furnace. New specifications, called low temperature and intermediate temperature properties, have been recently introduced. Low temperature specifications are characterized by disintegration of pellets in the 500°C (930°F) range in the upper portion of the granular zone during the hematite-to-magnetite transformation in blast furnace stack. Intermediate temperature properties (measured by 1000°C or 1800°F) are characterized by swelling, reducibility, and compression strength after reduction, reflecting conditions in the lower portion of the granular zone of the furnace. These new parameters are being used for pellet quality evaluation at Inland, and will be introduced at its Minorca mine for more routine analysis and correlation with the pellet furnace operation. With increased emphasis on quality, effective communication between the blast furnace operator, research, and the pellet plant operator is critical. At Inland, this is accomplished through technical meetings where the opportunity is provided to solve problems, establish a common understanding on the value of quality, and develop future quality standards and programs. With the degree of sophistication in determining pellet quality as it affects blast furnace operation, the future pellet plant operator will actually be producing a custom pellet. Human Resources Technological change has been a strong point at Inland, and will continue to be. However, human resource management is equally important. Is management giving sufficient attention to employee motivation and involvement? It is a way to improve productivity, reduce costs, and enhance employee job satisfaction. The industry is beginning to understand the principles and the potential for tapping employee brainpower. The payoff can be handsome. Management has to be willing to share both information and power if participative management is to live up to its potential. It has to become more flexible and be willing to adapt to change on the human side. Management should embrace rather than fear employee involvement. Given time, joint problem solving will replace adversarial attitudes and pay dividends for both sides. Productivity and product quality will improve and new dimensions of employee job satisfaction will be achieved. But, it will not happen overnight. Attitudinal change must permeate the organization from top to bottom. This change is needed to support the working relationships and give everyone a sense of direct and meaningful involvement.

Jan 11, 1983

By M P. Cipold, J F. Bachmann, C C. Bachmann, J Ha, H B. Wurst

In washability, the objective is to establish the set of maximum possible separation performance criteria for a given mineral feed. The method of choice for this has been the conventional sink–?float analysis. Using traditional sink–float method it is not possible to sample and automatically measure. This fact, as well as time, cost and safety aspects, as well as required and manageable sample size of the sink–float method have prompted the search for a new approach for establishing separation performance criteria. This is especially important as performance levels of separator plants can be maximised if reliable information based on an analysis of washability in conjunction with particle size distribution, elemental constituency becomes available in time. The new method to establish washability and associated performance information utilises at least two measurement technologies concurrently: single energy X-ray transmission and image processing. For porous or very inhomogeneous materials the results can be refined further by using dual energy X-ray transmission and image processing.If used as a standard laboratory device the continuous build-up of the washability curve allows to evaluate the statistical significance of the sample size during measurement.The measuring method can even be improved if it is combined with an automatic sampling system that feeds a continuous and representative particle stream to the analyser. Then the value of the collected data increases considerably since the washability data are additionally available in time to be considered in the control of the process plant. The washability curve can be derived and is continuously updated based on the particles measured during the past time interval. Older curves and results are stored in a database and can be retrieved for later reference. This technology now enables automated sampling and integrated automated measurement, which was previously not possible.This incorporation of an automated washability monitor at a representative sample gives near real-time data that would impinge positively on the profitability of the plant operation. The method was extensively tested using a range of samples with different densities, varying from 1 g/cm3 (coal) to 5 g/cm3 (iron ore).CITATION:Bachmann, C C, Bachmann, J F, Cipold, M P, Wurst, H B and Ha, J, 2017. Inline analysis of washability parameters for process control, in Proceedings Eighth World Conference on Sampling and Blending , pp 213–218 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

By Klaus Rieker

North of Antwerp central train station, two single-track tunnels for the high-speed train line between Brussels and Amsterdam were constructed. At the same time, the central train station was modified to a through station. Both 1.23 km tunnels are situated in the Antwerp sands and were constructed using a slurry shield machine. Due to the inner city location, the tunnels run over their entire length underneath structures, in some cases with only minimal clearance. The paper deals with these challenging situations. In addition, the tunnel boring machine, the tunnel lining and measures to limit settlements will be introduced.

Jan 1, 2007

By Gualberto Salas Torrelly

El avance tecnológico en los sistemas de iniciación en voladura abarca desde el sistema convencional (Mecha de Seguridad y Fulminantes hasta el sistema de iniciación electrónica, donde a través de un control de vibraciones se controla la energía liberada en un disparo, optimizando la fragmentación y disminuyendo el daño a las paredes del pit. En ese sentido, el sistema de iniciación con detonadores electrónicos, fija con claridad los conceptos de precisión, flexibilidad y seguridad. Por ello, el presente trabajo señala el uso de detonadores electrónicos por la Sociedad Minera Cerro Verde con la finalidad de evaluar sus resultados en seguridad, precisión, fragmentación, vibraciones, y control de daño a las paredes de la mina. Los resultados fueron óptimos -en tanto mejoró la fragmentación, el proceso de carguío y se incrementó el flujo en chancado primario.

Sep 12, 2005

By Luis Orna

El trabajo que se ha desarrollado en Minera Yanacocha, conjuntamente con las áreas de Mantenimiento Mina y Operaciones Mina, es realizar una solución integral en línea y tiempo real de la programación de las actividades de mantenimiento preventivo y correctivo de los equipos pesados en el taller de mantenimiento. La idea con esta solución fue que los planeadores, programen los trabajos desde su inicio a finalización, de modo que se visualiza el avance en diferentes dispositivos (monitores, dispositivos móviles, etc). Los técnicos del taller de mantenimiento, como valor agregado pueden monitorear sus actividades, cerrar las órdenes de trabajo si es necesario, todos estos trabajos son realizados con información mediante interfaz a ERP.

Sep 1, 2017

By J. Dienenthal

Automatic Charging and Stoking Machines for use at ferroalloy furnaces are in operation for more than 20years. Dango & Dienenthal Maschinenbau GmbH (short: DDS) has developed several machine generations. Today advanced solutions help to achieve better charging and stoking results to minimize cost and to improve the working environment around the furnaces. Three different alternatives can be considered: Rail-mounted solution The machine(s) travel(s) on an overhead monorail to one or several furnaces and is locked in the desired working position from where charging and stoking is performed. Mobile solution This machine travels on the charging platform and is also locked at the respective working position to perform charging and stoking. Automation of a standard mobile charging and stoking machine A standard charging and stoking machine can be adapted for automation. A reliable navigation system is included. Charging and stoking is performed with the moving machine. Advantage versus other solutions: considerable lower investment cost and possibility to upgrade the mobile charging and stoking machine for later automation. Overall, automatic charging and stoking can save up to 10 per cent of the specific smelting energy. A better and more consistent furnace operation can be achieved. Different programs are used to cope with different furnace conditions and changing raw materials. All machine movements can be recorded and correlated to other furnace parameters. Working environment on the charging platform is greatly improved.

Jan 1, 2007

As Pliny commented two millennia ago, The only certainty is that nothing is certain. Despite the many breakthroughs, advances and promises, the way we each live and work remains awash with technological, economic and political uncertainty. The resources sector is no exception in this regard. Mining itself is much more than a complicated process or recipe; it is a complex adaptive system. The way we adopt and adapt new technologies, the way we evolve data into corporate wisdom, the way we make decisions and even the way we view our concept of rationality should each be the subject of intense review. Translating these sentiments into sustainable company growth is indeed the challenge. This is unlikely to be achieved within convention, but through innovation. The game is changing!

May 1, 2010

By F. N. Voskoboyev

The suggested new method for control of geomechanical state of undermined rock mass ensures, as a safety measure for the earth surface protection, the decrease of deformations by 2,5 - 10 times in mining the single seam, and by 1,5 - 5 times - in mining bed series, i. e. approximately within the seam ranges as in the application of full packing with various compressive properties or partial extraction of resources over the area with different coefficients of extraction. It should be noted that this new method has the following advantages o\w rhr. conventional methods: a) the decrease of the packing area and packing works volume by 2 - 4 fold including the operating and productive expenses; b) the elimination of mineral losses due to the increase of extraction coefficient up to 100 5%; c) rock utilization from workings drivage by its placing in the mined - out space. Perspective field of application of this method: disconservation of mineral resources in the left protective pillars of various designation.

Jan 1, 1996

By Andrew P. Schissler

The Citronen Zinc-Lead Project is one of the world?s largest undeveloped zinc-lead resources, containing more than 13 billion pounds of zinc and lead metal. The project is located in northern Greenland, a self-governed region of the Kingdom of Denmark (Figure 1). Citronen is the northern-most mine in the world, operating at a latitude of 83o 3? N. In excess of 67,000 meters of diamond drilling have been completed to delineate the resource. As of January 2012, the measured, indicated, and inferred reserves for the Citronen project totaled 70.8 million tonnes, consisting of 5.7% zinc + lead (3.5% zinc cut-off) (Ironbark, 2012). For the underground mine plan, room-and-pillar and long holestoping mining methods were selected. The beneficial application of structural fill was considered for increased recovery, efficient tailings disposal, and ground control. Three types of fill were compared - paste fill, cemented rock fill, and iced tailings. An environmental and economic feasibility study concluded that iced tailings was the preferred alternative provided it met the ground control requirements. The purpose of this paper is to explain the investigatory steps that led to the possibility for the use of iced tailings as structural fi

Jan 1, 2012

By K. Nielsen

The Norwegian tunnelling industry has made remarkable improvements both with regard to productivity and cost efficiency over the last 30-40 years. This development has been made possible by continuous improvement driven by innovation. Based on a generic description of the innovation process and the innovation system, the paper has used the development of modern tunnel drilling in the Norwegian tunnelling industry to discuss the characteristics of its innovation system with a focus on human capital issues and knowledge management.

Jan 1, 2006

By Martin Herenknecht, Michael Knabe, Ulrich Rehm

In Switzerland at present, the longest railway tunnels in the world, the Gotthard(57 km) and the Loetschberg base tunnel (34km) are under construction. For thischallenge six high-tech HERRENKNECHT Hard Rock Tunnel Boring Machines (TBM)are applied, which have to excavate approx. 80 km at the Gotthard and 20 km at the Loetschberg Tunnels. The machines being used are of a single Gripper-TBM type, which are equipped with the latest rock support techniques, in order to optimize the quality of the working conditions for the personnel which have direct impact on the quality of the tunnels. The different requirements of the projects based on different speci?cations within the tender documents led to completely different TBM concepts which will be reviewed in detail in this paper.

Jan 1, 2003

By Zajber A, Kulchen R, Letzel D, Weyer A, Schwellenbach J

The search for modem casting plant concepts today focuses more and more on the harmonisation and optimisation of overall concept lines to obtain a continuous quality control and reduce the cost of production (Figure 1). Fin I As far as continuous casting plant concepts are concerned, this specifically requires an optimal adaptation and flexible operation when converting liquid steel into a directly processable product without any in-between treatment. Continuous casters need to fully satisfy the requirements of both the upstream steelmaking facilities as well as the downstream rolling facilities.

Jan 1, 1999

By Doug Halbe

A number of CIP plants have been built in Western Australia in the past two years. The authors have surveyed several of these new plants and present drawings, data and discussion of operating and design innovations and areas of interest.

Jan 1, 1982

By C. N. Harman

Steel is the most versatile material which has made the progress in every aspect on this earth possible. There are hundreds of varieties of steel because for each application it has to be made with specific properties to get the most optimum usage. It is well known that the basic constituent of steel is iron. But it is the proportion of other elements in it, which give each type of steel certain specific properties. These elements are added in liquid iron inform of Ferro alloys to get the desired composition and properties. Thus, Ferro alloys are important additives in the production of steel. It can be said that no steel can be made without use of one or more of the several Ferro alloys. They form the backbone of steel. Thus, the Ferro alloys industry is vitally linked for its growth and development to that of the steel industry. Ferro alloys industry in India has never been globally competitive, despite its rich ore deposits and low-cost manpower, essentially due to a) Insufficient availability and high cost of electric power b) Increasing ores and reductants cost c) Non-availability of low ash, low phos. coking coal in the country for the production of desired coke with low ash, and low phos. contents, making import of such coke at a high cost imperative d) High-cost and insufficient infrastructural facilities (both road and rail) for rapid transportation of ore from mines to plants e)Stiff competition from producers and exporters of Ferro alloys in other countries like South Africa, Kazakhstan, China, Russia, Australia etc. due to global trade agreement which has made drastic reduction in customs duty on imports necessary. f) Wide fluctuations in the International price of Ferro alloys depending on demand versus supply. To over come these challenges plus adhering to stringent pollution control norms innovations are inevitable in the process technology, and plant equipment design, along with frequent changes in product mix, to be more cost-effective. An attempt is made in this paper to address the innovations that took place in the past and those that further need to be made, considering the future of this industry.

Jan 1, 2007