Search Documents

By R. Ruka, E. A. Gulbransen

ONE of the interesting questions in the understanding of the reaction of iron with oxygen is the kinetics and the mechanism of the crystal structure changes occurring in the formation and breakdown of the oxide film. In a recent work' the electron diffraction method was applied to the study of the solid phase reactions occurring internally in the oxide film on iron above 570°C and under vacuum conditions. The higher oxides which form under oxidizing conditions are reduced internally by the diffusion of iron into the oxide leaving the bulk of the oxide FeO (wüstite). This paper will ask and consider three questions. These are: (1) What is the nature of the depressed transformation temperature for the Fe3O4 + Fe ? 4Fe0 reaction in very thin oxide films?; (2) What is the mechanism of the forward transformation of Fe3O4 to FeO at or near 570°C?; and (3) What is the nature and mechanism of the slow reverse transformation of FeO to Fe3O4 and Fe below 570°C?. The composition of the oxide as well as its electrical, magnetic, mechanical, and chemical properties depends upon the kinetics of these reactions. Literature Survey The composition of the oxide film on pure iron at temperatures up to 570°C has been studied extensively by the electron diffraction method. Nelson,' Jackson and Quarrell,3 and Gulbransen and Hick-man4 have shown that Fe3O4 and a-Fe2O8 are formed in the temperature range of 225" to 570°C, while y-Fe,O, is most likely formed below 225°C for long oxidation times. In very thin films FeO (wüstite) is found to form at temperatures as low as 400°C, and its existence depends essentially upon the extent of initial oxidation. FeO is not found in the formation of thick films below 570°C. On the other hand X-ray5 and micrographic8 studies show that Fe3O4 may exist as the main com-ponent in thick films up to 650°C, well above the equilibrium temperature for the reaction Fe3O4 + Fe ? 4FeO. The kinetics of the forward and reverse trans-formations of the reaction Fe3O4 + Fe ? 4FeO have not been studied in oxide films. However, analysis of the data of Gulbransen and Hickman4 on the heat-ing and cooling of iron oxide films of known thick-nesses in high vacua shows that the forward reac-tion proceeds rapidly even for a 4000 A film at temperatures of 575" to 600°C. The reverse reaction or decomposition of wüstite (FeO) occurs at tem-peratures below 450°C. Thus, there appears to be a slow process in the decomposition which is in marked contrast to the rapid forward reaction. The decomposition of a bulk sample of FeO free from the metal has been studied extensively by Chaudron, Benard and coworkers using the micro-graphic, X-ray diffraction, and thermomagnetic methods. Chaudron7,8 first observed that the de-composition of FeO (wüstite) below 570°C occurs by the reaction 4FeO ? Fe3O4 + Fe. Later work by Chaudron and Forestier5 showed that the rate of de-

Jan 1, 1951

By Y. C. Liu, H. Margolin

Investigation of martensite habit plane in water-quenched Ti-Mn alloys was carried out in the range of manganese contents between 4.35 and 5.25 pct. On the basis of 22 measurements, the poles were observed to fall into two groups, indicating the existence of two habit planes. The Miller indices of the poles close to these two groups were found to be <334>ß and <344>ß. TITANIUM has an allotropic transformation at 882.1° ± 0.5C1 by which the high temperature ß (body-centered cubic) phase changes to a (hexagonal close-packed) phase. It is well known, as in the case of low carbon steel, that the unalloyed high temperature ß phase cannot be retained no matter how rapid the cooling rate. However, the addition of alloying elements usually lowers the transformation temperature continuously and stabilizes the ß phase to a temperature much lower than the allotropic transformation temperature in pure titanium. A typical example of this behavior is found with manganese-alloying of titanium. Fig. 1 shows the titanium-rich Ti-Mn equilibrium diagram as established by Battelle Memorial Institute.&apos; The addition of manganese lowers the ß transus line and the eutectoid reaction takes place at 550°C, the eutectoid composition being 20 wt pct Mn. However, upon quenching to room temperature from the ß field, the ß phase can be completely retained with much less manganese, see Fig. 2. If the composition is less than that required to stabilize the ß phase completely, a plate-like structure, similar to that of martensite in other alloy systems, appears as shown in Fig. 3. Much lower alloying content merely intensifies the amounts of these transformed structures, as shown in Fig. 4. This paper presents the results of an investigation of the habit plane of these martensitic structures in Ti-Mn alloys. Experimental Procedure Investigation of the pole of a given platelet was made using the two-surface method of analysis." In order that a given martensite trace on two surfaces be readily recognized both at low and high magnifications, it is desirable that only a small amount of martensite be present. From a review of the data obtained at Battelle Memorial Institute4 on quench hardening in Ti-Mn alloys and the results of Duwez" on transformation in Ti-MO alloys, it was decided that the most appropriate Ti-Mn composition for this study would be about 6 pct Mn. A group of alloys containing from 3 to 10 pct Mn was made to bracket this composition. The choice of the 6 pct alloy was apparently proper, since it was later learned that approximately 5.5 to 6 pct Mn is required to stabilize the ß phase on water quenching.

Jan 1, 1954

By J. C. Fisher

Nucleation theory is applied to martensite nucleation in substitutional iron alloys. Composition fluctuations are neglected, and a steady rate of nucleation is predicted for any composition and temperature. The maximum rate of nucleation (as a function of temperature) is shown to be measurable only for on extremely narrow composition range, being too great or too small outside this range. A number of experimental observations, including completely isothermal transformation in some alloys and composition-dependence of M. temperature in others, are compared with the calculated behavior. IN a previous report,¹ nucleation theory was applied to the formation of isothermal martensite in an Fe-Ni-Mn alloy. The experimental observations of Cech and Hollomon² were accounted for quantitatively. It now is of interest to examine the predictions of nucleation theory with respect to martensite transformation in substitutional iron alloys of other compositions. Since Fe-Ni alloys have received considerable attention, both as to their transformation kinetics and their free energies, they will be treated in detail, although the results apply with equal validity to other substitutional alloys. In substitutional alloys, where composition fluctuations can be neglected in volumes of critical nuclear size, the rate of nucleation of martensite in subcooled austenite is¹ n - Nv exp (—W*/kT) [I] where the free energy of formation of the critical size nucleus is W* = 8192 p (?² s³) [2] In the expressions for n and W*, the symbols have the following meanings: N is the number of atoms per unit volume; v, the atomic vibration frequency; 8, a function of the elastic constants of austenite and the shear angle of martensite; , the austenite/mar-tensite inter facial free energy; and ?fc is the free energy change per unit volume accompanying the transformation. Jones and Pumphrey² have determined the austenite to martensite free energy change as a function of nickel content and temperature for Fe-Ni alloys. Their expression is ?F = 2500 C + 1.25 (1 —C)?FFc cal per mol [3] where C is the atom fraction of nickel, and ?Ffe is the free energy change per unit volume for pure iron as tabulated by Zener4 (or, equivalently, Fisher"). From Eqs. 1 to 3, it is possible to calculate isothermal nucleation rates as a function of temperature and composition for Fe-Ni alloys. The only unknown parameter is (?² s³). The best value of this parameter for Fe-Ni alloys, determined from M. temperatures in a manner to be described shortly, is (?² s³)= 9.92 (10)21 cgs units [4] Taking this value of (?² s³), C-curves for isothermal nucleation were calculated for Fe-Ni alloys of several compositions, and are plotted in Fig. 1. It is evident from Fig. 1 that completely isothermal nucleation of martensite in Fe-Ni alloys can be observed experimentally for only a very narrow range of compositions. Cech and Hollomon find that a nucleation rate of about 10&apos; nuclei per cc per sec is as fast as they can follow dilatometrically, and a rate of about 10-1 nucleus per cc per sec is about the slowest that can be measured conveniently. If the nucleation rate is to lie between the limits 10-1 10 the nickel content of an Fe-Ni alloy must fall in the atomic fraction range 0.299 5 C 5 0.302. Nickel contents lower than 0.299 correspond to nucleation rates too great to follow, and those higher than 0.302 to nucleation rates too slow to measure in a reasonable time.* In view of the narrow corn- position range in which successful isothermal measurements can be made, it is not surprising that only one substitutional alloy has been described&apos; that comes close to being in the proper range.

Jan 1, 1954

By Y. C. Liu

Both the habit plane of martensite and the orientation relationship between the matrix and martensite platelets of different habit planes have been investigated in binary titanium alloys with molybdenum, chromium, and iron. The effect of the mode of deformation on the martensite habit plane was studied. A micrograph of an exposed mar-tensite platelet is presented. IN the study of martensitic transformation in Ti-Mn alloys,&apos; two martensite habit planes—{334), and {344)8—were reported. The {334), habit was also observed in unalloyed titanium upon transformation,&apos; although there is disagreement with respect to the exact indices. The other habit plane, {344),, has not been reported in martensitic transformation in any other alloys. The present investigation was made to determine whether other binary titanium alloys with P-stabil-izing elements would exhibit a crystallography of transformation similar to that of Ti-Mn alloys. Furthermore, since martensite platelets can be induced by deformation under certain conditions, it was of interest to investigate whether the mode of deformation, compressive or tensile, would influence the formation of martensite platelets on a specific plane in an alloy system which possesses two martensite habit planes. Experimental Procedure The material used for the preparation of the binary alloys of iodide titanium with molybdenum, chromium, and iron had the following purities: 99.99 pct iodide titanium, 99.9 pct molybdenum, 99.423 pct chromium, and 99.9 pct iron. The compositions of alloys listed in this paper are in nominal weight percentage. All specimens used were prepared and treated according to the procedure described in reference 1, unless stated. For the subzero temperature treat,ment the following experimental schedule was followed. After specimens had undergone the grain-growth treatment, they were quenched into an ice-water bath and were then metallographically examined. In specimens of higher alloy content, no martensitic transformation was observed. In those in which mar-tensitic transformation did occur, only specimens in which the martensite platelets existed as fine needles in localized regions were used. All specimens were reannealed 17 hr at 1200°C, quenched into ice water. and the capsule was broken. They were held in the ice water for from 5 to 10 sec, then transferred to a liquid-argon bath. This stepped quenching procedure was found to be more efficient than direct quenching into liquid argon. In the latter case, as soon as the hot specimen was immersed in the liquid argon, a protective, insulating layer of argon gas formed, and the specimen continued to glow vividly in the bath for some time. In the study of the habit behavior of martensite produced by deformation, specimens were deformed at room temperature either by compression, tension, or rolling. Martensite habit planes were determined by the two-surface analysis procedure described in reference 1. A stereographic net of 153/4 in. diam was used throughout the investigation. The method for determining the orlentation relationship between martensite and the matrix follows that used by Greninger and Troiano.&apos; A diamond-polishing table with its auxiliaries was used in order

Jan 1, 1957

By H. Reiss

The zone-melting process in which redistribution of solute in a solid bar is effected by the passage of a molten zone is considered mathematically. Simple approximate techniques are developed for computing the manner in which redistribution occurs as molten zones continue to pass. The introduction of the "zone-melting flux" provides valuable insight into the nature of the phenomenon, as well as a central mathematical theme in terms of which the process can be discussed. Curves are presented for typical and general cases. AN extremely efficient purification technique was described recently by Pfann.1 Known as zone refining, it consisted of the slow passage of a series of molten zones, produced by external heaters, through a long solid ingot of the substance to be purified. Equations were given for the maximum separation attainable, and a numerical computation method was described for obtaining the concentration in the ingot after a given number of zone passes. The present paper offers an interpretation of the physical nature of zone melting in terms of a transport process in which formal diffusive and convec-tive flows occur. This interpretation, in addition to providing insight into the physical nature of the process, also provides a basis for its mathematical treatment. From this basis, useful equations are developed for the solute concentration in the ingot as a function of the number of zone passes. These are applicable particularly where large numbers of passes are necessary and where numerical computational methods might be laborious. All considerations will deal with the limiting form of the process, described by Pfann,&apos; in which: 1—Diffusion in the solid is considered negligible. 2—Mixing in the liquid is supposed, complete. 3—The distribution coefficient, k, measuring the ratio (at equilibrium) of solute concentration in the solid to that in the liquid is supposed, independent of composition. In general, this paper will be concerned with a bar of uniform (actually unit) cross section, ex- tending in the x-direction from x = 0 to x = L, where L may be infinite. Zone melting is a transport process, and as such must admit of interpretation in terms of a flux of transported quantity. However, the progress of operation is not measured in units of time but in terms of the number of completed zone passes. Consequently, the zone-melting flux will be a rate, per unit pass, rather than per unit time. The description of this flux and the examination of its properties is given below. Zone-Melting Flux Fig. 1 represents an intermediate stage of the nth pass. Concentration C is plotted against distance, x. The molten zone with its back at the point x and front at x + I moves in the direction indicated by the arrow. As it moves, it leaves behind the nth

Jan 1, 1955

By R. W. Hertzberg, F. D. Lemkey, J. A. Ford

The technique of unidirectional solidification has been applied to the A1-AI3Ni and A1-CuAl2 ezltectic alloy systems; the controlled microstructure of A1-A3Ni consists of parallel A13Ni whiskers emhedded in an aluminum matrix while the Al-CuAl2, system solidifies as parallel alternate lamellae of aluminm and CuAl2. Mechanical tests (tension and flexure) have shown that the particle-matrix interface bond formed during unidirectional solidification allowes for efficient load transfer from the matrix to the reinforcing phase. Strength and fracture characterstics of the alloys were studied as a function of phase orientation; the tensile strength of controlled Al-Al3Ni samples was 43,000 psi (three times greater than that of as-cast specime~s). The strength of the Al-CIA2, cutectic was studied as a function of lamellae-flexure stress-axis orientation using a microbend apparatus. A twofold increase in outer fiber stress was observed as the lamellae were rotated from a position of no reinforcing (perpendicular to the stress axis) to one of maximum reinforcing (parallel to the stress axis), The brittle reinforcing constituent in each alloy (A13Ni and CuAl2) was observed to he the nucleating phase for fracture. It is to be concluded from this investigation that unidirectionally solidified eutectic alloys have a potential use as reinforcing coniposite) materials. In a recent review article, Chadwick1 has described the work of many investigators in the area of controlled solidification of binary eutectic alloys. Thus far, more than twenty eutectic alloys have been unidirectionally solidified to produce structures consisting of two phases in the form of alternating lamellae or as whiskers embedded within a continuous matrix; in either case, the phases are aligned parallel to the growth direction. In particular, Kraft and Albright2 have shown that the Al-CuA1, eutectic alloy exhibits a lamellar microstruc- ture as a result of unidirectional solidification while Lemkey, Hertzberg, and Ford3 have studied the A13Ni whisker-aluminum matrix morphology in the A1-A13Ni system. Whether these alloys could exhibit reinforcing behavior would have to depend upon the strength and volume fraction of the reinforcing phase (AI3Ni and CuA12) and the nature of the bond between the reinforcing phase and the matrix. Hertzberg and Kraft4 have shown that the interface bond between chromium whiskers and a copper matrix in unidirectionally solidified Cu-Cr is particularly good while Lemkey and Kraft5 have reported chromium-whisker tensile strengths in excess of 1,000,000 psi. However, with the chromium volume fraction being less than 2 pct, no reinforcing behavior was displayed by the Cu-Cr alloy.6 In view of the encouraging results concerning the good interfacial bond and high strength of the reinforcing phase in the Cu-Cr system and preliminary mechanical test data reported by Lemkey et al.3 for the A1-A13Ni system, the A1-CuA1, and A1-A13Ni eutectic alloys containing 50 and 10 vol pct, respectively, of the reinforcing phase give promise of possessing mechanical reinforcing behavior. Based on this premise, the objective of the investigation was to study the strength and fracture behavior exhibited by these anisotropic microstructures. EXPERIMENTAL PROCEDURE Controlled Solidification Procedure. An extensive description of the technique of unidirectional solidification has been presented elsewhere.&apos; However, the pertinent details for each eutectic system studied are discussed below. Al-A13Ni System. Several master heats of this alloy were prepared by vacuum-induction melting in an A12O3crucible and casting in SiO2 mold or by induction melting in alumina crucibles under argon. The initial heats were prepared from 99.99 pct A1 and 99.99+ pct Ni, while later heats used 99.999+ pct A1 and 99.99+ pct Ni. Specimens of these master heats were unidirectionally solidified using induction and resistance heating sources and argon atmospheres at growth rates from 1.1 to 28.7 cm per hr. The thermal gradients in the liquid were controlled in the range of 26" to 36°C per cm for these runs. Al-CuA12 System. The master heat and controlled

Jan 1, 1965

By J. B. Morgan

The mechanical behavior of MgCu2 from 20 o to 725°C has been determined by "brittle-ring" tensite-test techniques, axial compression, and bending experiments. Compressive ductility begins at 450°C (0.65 T/Tm) and slowly increases with increasing temperature white the tensile ductility is characterized by an abrupt brittle-ductile transition at 600°C (0.8T/Tm). The compressive strength increases eightfold from room temperature to 400°C with a "normal" decrease as the temperature is further increased. The tensile strength goes through a rather abrupt threefold increase above 600°C with a subsequent decrease at higher temperatures. The slip system is (111)[110] and the twinning system is (111)[112]. At high temperatures MgCu2 is quite rate-sensitive, and dynamic yield points are observed that are extremely orientation-dependent. The high-temperature creep behavior under constant load is characterized by an increasing strain-rate with time. The general characteristics of the mechanical behavior make it possible to classify MgCu2 with those materials in which initial mobile dislocation density and the dislocation velocity-stress dependence are significant in determining mechanical response. Mgcu2 is the C15 prototype of the cubic Laves phase. Its range of homogeneity extends from 32.8 to 35.5 at. pct Mg at 500°C and narrows at lower temperatures. The lattice parameter is reported to vary from 7.02 to 7.05A,1 and the compound is completely ordered to the melting point of 819°C. MgCu2 has a brassy metallic appearance, is extremely brittle, and many of its physical properties are intermediate between those of the constituent elements: the electrical resistivity is 3.5 x 10-6 ohm-cm, Young&apos;s modulus is 10x 106 psi, the shear modulus is 6 x l06 psi, and the thermal coefficient of expansion is 18.7 x 10-6 cm per cm per "C from 20" to 250°C. Usually, properties of intermetallic compounds as functions of temperature have been determined by hardness, compression, or impact behavior, and almost all of these experiments have been performed on polycrystalline materials. Tammann and Dahl,2 for instance, determined the onset of ductility in a series of binary intermetallics by ball-hardness measurements and found the onset to range between 0.71 and 0.96 T/T,. Lowrie&apos;s3 investigations included some tensile properties, and he found ductility beginning around 0.65 T/Tm for most materials examined. His work did include some data on polycrystalline, nonstoichiometric MgCu2, however. The present work is an attempt to extend the examination of the particular compound MgCu2 in single-crystal form in order to aid the formation of general concepts about mechanical be-

Jan 1, 1965

By George A. Roberts, Arthur H. Grobe

H. H. Hausner (Sylvania Electric Products Inc., Bayside, N. Y.)—I tested the 18-8 stainless steel powder described by Grobe and Roberts and the results were excellent. The powder was compacted and sintered in purified hydrogen to a very low density (approximately 20 pct and more porosity). Where the other powders show very little ductility when sintered to such a low density, the described stainless steel was surprisingly high in ductility. I would appreciate it if the authors could give us some data on a similar powder but without silicon and also data on 430 stainless steel powder. H. S. Kalish (Sylvania Electric Products lnc., Bay-side, N. Y.)—I should like to verify the excellent results obtained by Grobe and Roberts with their pre-alloyed stainless steel powder. It seems to me, however, that their data are conservative and that even better densities and higher tensile strength can be obtained with these powders by the selection of proper particle size fractions. The accompanying data were obtained by sintering compacts pressed from the powder made by Vanadium-Alloys Steel Co. to 0.8 in. in diam about % in. high in a cylindrical double action die without the use of lubricant. The compacts were sintered for 1 hr at 2370°F in hydrogen purified by passing it through a Deoxo unit (palladium catalyst) and a Lectrodryer. Even the density obtained using the as-received (—100 mesh) compacted at 40 tsi was quite high as was the hardness. This indicates that by increasing the sintering temperature slightly above 2350°F the coining and subsequent secondary sintering operation can be avoided. With the — 325 mesh fraction, however, very much higher density can be obtained and a high hardness. I have no tensile data to present, but I feel that it is not too optimistic to expect. that unusually high tensile strengths and good ductility can be obtained in this sintered material on the basis of the density and hardness data. The sintered stainless steel made by the above-described methods came out of the furnace very bright and clean. The purified hydrogen atmosphere is important in sintering stainless steel to reduce the oxide present in the powder. The result of such a sintering is good densification and good ductility of the sintered product. G. A. Roberts (authors&apos; reply)—We are greatly indebted to Messrs. Hausner and Kalish for their discussions of our paper. Their encouraging remarks are greatly appreciated and their confirmatory data will do much to add to the value of the paper. At the present time it is impossible to provide complete data on a similar stainless steel powder without silicon, but we do know that, in general, the properties are slightly inferior. Data on such a powder and on other stainless steel types are to be published in the near future.

Jan 1, 1952

By Bernhard Blumenthal

A melting process was developed by which high purity electrolytic uranium crystals can be converted into sound ingots without serious contamination. Careful preparation of the crystals, melting in a high vacuum, and directional solidification led to a metal of better than 99.993 wt pct purity. The metallographic examination showed a substantially clean metal with only residual amounts of a second phase which responded to heat treatment. The density of high purity uranium is 19.05 g per cu cm. FOR the study of the fundamental properties of uranium and its alloys, a base metal of high purity is needed, and an investigation was started at Argonne several years ago to examine various methods of preparing high purity uranium. Early success was achieved by the fused salt electrolysis process in preparing high purity metal in crystal form,&apos; and the problem became that of melting the crystals into ingots without contamination. The electrolytic crystals contained a few ppm of heavy metals, less than 15 ppm C, and large quantities of potassium and lithium in the form of trapped fused salt electrolyte. On melting in vacuo in magnesia or urania crucibles, the metal picked up considerable quantities of carbon and some iron, copper, and silicon but lost most of the potassium and lithium. It was not metallographically clean, and much research work was necessary to determine the optimum melting conditions for minimum contamination. This work has resulted in the development of a melting procedure by which sound ingots can be prepared with only a limited contamination by carbon. In the section entitled "Melting of the Electrolytic Metal," the equipment and processes that have been developed for melting the electrolytic crystals are described in detail. The "Metallography" section is devoted to the metallography of high purity uranium, and the section "Density of High Purity Uranium" contains the first property measurement on high purity uranium—a density determination. Melting of the Electrolytic Metal Apparatus—Melting and Vacuum Equipment: Uranium may be melted in either resistance or induction-type electric furnaces. Resistance heating was found to be preferable to induction heating for melting down the electrolytic crystals, for several reasons: Although induction heating permits fast heating, this advantage cannot be utilized when crucibles with limited thermal shock resistance are used. Temperature control of induction-heated melts is poor, and the stirring effect increases the rate of contamination of the melt from the crucible, slag, or the furnace atmosphere; liquation and controlled solidification are difficult to carry out. Because of these objections, resistance heating was chosen. A 10 kw Globar resistance furnace of low heat capacity permitted uniform heating of a uranium charge to its melting point in 45 min. The furnace was insulated with a removable aluminum shield so that, after melting and removal of the shield, the furnace could be quickly cooled to room temperature. The furnace was equipped with an apparatus for directional solidification; see Fig. la. The crucible was suspended in the center of the furnace; and when the melting was complete, the crucible was slowly lowered into the cold end of the furnace tube. Solidification took place upward from the bottom; and when the rate of lowering was small, a sound ingot free from sink holes and shrinkage cavities was produced. To remove the large quantities of gas contained in the electrolytic crystals, melting in a high vacuum is mandatory. While, from the standpoint of contamination, melting in a highly purified argon atmosphere appeared feasible, lithium and potassium removal proved less efficient under such conditions. Also, a vacuum-melted ingot has a cleaner surface than one melted in an inert atmosphere. The vacuum system must be of very high pumping speed and leak tight so that a vacuum of less than 2x10-7 mm Hg is attainable when the system is pumped down cold. The system must have a high pumping speed, so that the pressure maximum which may rise to 1x10-4 mm during heating can be quickly reduced

Jan 1, 1956

By H. D. Mellom

The direction of the optic or "C" axis of a uniaxial metal crystal can be found with the metallurgical polarizing microscope by examining two planes of section on the crystal. Complete orientation of the crystal can be determined if a twin crystal is common to both surfaces of section. Examination of Uniaxial Metals in Polarized Light-Rotation of a uniaxial crystal surface, properly prepared,&apos; shows four extinction positions 90 deg apart, provided that the surface is not close to a basal section. One of these two extinction directions corresponds with the projection of the optic axis on the surface of section. This direction can be found if the &apos;sign of the rotationr2 for the metal is known. To find the direction of the optic axis, the crystal is rotated on the stage 45 deg from an extinction position. With a crystal of negative sign, to produce extinction the analyser must be rotated towards the optic axial direction and vice versa. All sections, other than basal, of a uniaxial crystal have the same sign of rotation and, since there is no change in sign with wave length, white light can be used for these measurements. U the sign of the rotation is not known the presumed direction of the optic axis can be determined assuming a positive sign. A third section cut normal to the presumed optic axis will show basal extinction if the assumption is correct. It is convenient to use the edge between the two planes of section as a fiducial direction common to both surfaces. The optic axis can be related to this direction. If the above measurements are repeated on the other plane of section and the angle between the two section planes measured, stereographic projection can be used to determine the orientation of the crystal optic axis. Determination of Complete Orientation—The complete orientation of a uniaxial crystal can be determined provided that a twin crystal is common to both surfaces of section, and the twin law is known. The orientation of the twin crystal optic axis can be determined in the same way as for the main crystal

Jan 1, 1962

By E. E. Schumacher

IN a laboratory devoted to the furtherance of the science of communication, the breadth and variety of the problems encountered are challenging to a metallurgist. In my own long association with the Bell Telephone Laboratories, our metallurgical group has dealt with a vast number of alloys, both ferrous and nonferrous, and with many materials in the border range of metallic properties., The objectives of our design engineers embrace every phase of telephony, and the properties they desire in metals are generally unusual, frequently unique, and often conflicting. Commercial alloys have not always been available with properties to meet a special requirement in the telephone plant, and many alloys have had, therefore, to be custom-made. Anyone who has had the opportunity to observe the results of tests of all types on numerous such alloys, both commercially and specially produced, or who has taken part in the development of an alloy of some necessary, but new or unusual combination of properties, could not fail to be impressed by the frequency with which a desired goal has been reached or adequately approached through the presence of decimal quantities of alloying elements. Nor could One fail to be struck by the occasions when, conversely, of a minute amount Of impurity element has rendered an alloy useful. It is no exaggeration to state that the content be- hind the decimal point often spells success or fail-ure, and the critical content is sometimes far to the right of the decimal point as I shall later illustrate. The great effects of small additions have long been recognized and have, in fact, been described by many investigators. The importance of the minute, however, cannot be overemphasized. Therefore, in this discussion, I propose to illustrate for you some of the startling instances, drawn primarily from our own experiences, wherein small, even vanishingly small, proportions of stranger elements in otherwise common aggregates have com-pletely changed the customary pattern of behavior. No one property has a monopoly as to being dis-proportionately affected by minor elements. Nearly all properties are affected, but there is time here to include only a selected few. I have chosen, there-fore, three of general interest: strength, magnetic, and electrical properties. I shall inquire into both the mechanisms and consequences of these disproportionate effects and try to share with you the fascination and challenge of this field. Strength Properties of Lead and Lead Alloys To illustrate the effect of the minute on strength properties I have selected lead and its alloys, with which we have worked extensively for many years. Lead has the advantages of being available in quantity in a state of high purity and of being fairly easy to melt and fabricate without contamination to any extent detectable by the spectrograph. It has the interesting disadvantages of recovery and recrystallization at room temperature. Whether I

Jan 1, 1951

By H. L. Luo, P. Duwez, C. C. Chao

BY rapidly cooling alloys from the liquid state, it is possible to obtain solid solutions beyond the equilibrium concentrations, provided that the components are miscible in the liquid state. Typical such cases include CU-Ag,1 Pt-Ag,2 CU-Rh,3 nickel-base alloys with silicon, germanium, and tin,4 and cobalt-base alloys with silicon, germanium, tin, aluminum, and gallium.5 In the present note it is shown that terminal solid solutions can be appreciably extended in A1-Mg alloys. The alloys whose compositions are given in Table I were prepared by induction melting in tantalum crucibles under an argon atmosphere. Both aluminum and magnesium were 99.99 pct pure. Weight losses after melting were less than 0.2 pct for the aluminum-rich alloys and less than 0.4 pct for the magnesium-rich alloys. From these weight losses it was estimated that the compositions of the ingots after melting were accurate within 0.3 at. pct for aluminum-rich alloys and within 0.5 at. pct for magnesium-rich alloys. As indicated in Table I, the compound AuCd10 in which there is an ionic contribution to the bonding. The authors thank Dr. J. H. Westbrook of the Research Laboratory, General Electric Co., for arranging the supply of materials and for his interest. This investigation was supported by the U.S. Atomic Energy Commission under Contract AT(30-1)-1002, Scope I. some of the alloys were also chemically analyzed and the results confirmed the limits of uncertainty based on weight losses. Rapid quenching from the liquid state was achieved by techniques previously described.8,7 The principle of these techniques consists of propelling a small globule of liquid alloy (about 20 mg) onto a copper substrate. The thin foils easily detached from the copper substrate were analyzed by X-ray diffraction using a Debye-Scherrer camera 114.6 mm in diameter and either nickel-filtered copper Ka or iron-filtered cobalt Ka radiation. Since the back-reflection doublets were resolved, the wavelengths used in the computatioas were CuKal = 1.54050A and CoKa1= 1.78892A. Lattice parameters were obtained by extrapolation of the Nelson-Riley function, and the tables compiled

Jan 1, 1964

By S. A. Mersol, C. T. Lynch, F. W. Vahldiek

The room-temperature Knoop hardness of single -crystal titanium diboride has been determined. Variations in microhardness have been correlated with orientation and structural imperfections in the crystals. Maximum differences in hardness values of 750 kg per sq mm with respect to orientation and 450 kg per sq mm with respect to substructure were found. The effects of etchants, load on indenter, and degvee of cracking of indentation were studied. The average hardness was determined as 2800 kg per sq mm on the as-grown crystals. Annealing increased the average hardness to 3375 kg per sq mm. ThE microhardness of polycrystalline titanium diboride approximating the stoichiometric composition TiB, has been studied by several investigators. The values for the Knoop hardness number range from 2710 kg per sq mm (Khn = 2710 kg per sq mm) to 3400 kg per sq mm.&apos;-4 Samsonov et al.&apos; reported a Vickers hardness number of 3400 kg per sq mm (Vhn = 3400 kg per sq mm) at 120-g loads for a 98 pct Ti + B material of 96 pct theoretical density. Recently Dunegan measured the Vickers hardness and obtained 2060 kg per sq mm with a 10-g load (Vhnlo = 2060 kg per sq mm), 1425 kg per sq mm for Vhnloo, and 1320 kg per sq mm for Vhnlooo. We have obtained a Khnloo = 3000 * 350 kg per sq mm for hot-pressed polycrystalline TiB2 that was 99.1 pct Ti + B and 96.6 pct of theoretical density. The present investigation has been made on single-crystal titanium diboride boules, and is believed to be the first such study on TiB, crystals of known orientation. EXPERIMENTAL The single crystals were prepared by a Verneuil-type process using an electric arc by the Linde Division of Union Carbide Corp. The largest specimens were 6 mm in diameter by 12 mm long. The crystals were of theoretical density (4.50 g per cm3) with a Ti + B content of 99.8 pct. The major impurities present were: 0.03 pct (by weight) 0, 0.06 pct C, 0.01 pct Si, 0.05 pct Fe, 0.01 pct Cr, and 0.01 pct Ni. The crystals were boron-rich, the average boron content being 31.S7 wt pct (stoichiometric value is 31.12 wt pct), and titanium-poor, the average titanium content being 68.2 wt pct (stoichiometric value is 68.88 wt pct). Titanium was determined gravimetrically by cupferron precipitation and boron by titration of H3B03 from a NaOH-fused specimen after removal of titanium with BaC03. The outer edge of the boule accounted for some of the excess boron. An electron-microprobe analysis showed that the titanium content increased from 60.0 wt pct at the edge to 68.5 wt pct at D, ~ 1000 p, where D, = distance from outer edge (see Fig. 5). X-ray measurements indicate that the boules are single crystals with considerable substructure. Upon etching this structure is seen in the form of a Widmanstatten-type rhombohedral line pattern in the basal (c) plane and a parallel "lines" pattern in the prism (a) planes. A typical WidmanstHtten-type pattern is seen in in Fig. 1. Electron microscopy reveals that the lines are less than 1 p across, which does not allow direct electron probe or microfocus X-ray determination of their composition. The identity of the second phase has not been established. It might be a higher boride or a nonstoichiometric TiB2. On annealing above 2200°C the precipitate is dispersed and dissolves in the matrix. The best etchants found were HF/HNO/HO, KF(CN)$NOH/HO (Murakami&apos;s Etch), and A large number of other etchants were previously Studied. The acidic etchant produced an acicular or "needles" pattern in the (a) planes which is an etchant effect on the "lines" pattern.

Jan 1, 1965

By Lawrence H. Van Vlack, Alfred S. Keh

The distribution of sulfur in iron was found to be dependent upon the time and temperature of the treatment as well as the chemical composition of the sulfide. With higher temperatures, the sulfide phase spreads more extensively between the iron grains. A complete network, however, does not form until approximately 1300°C (2372°F), ot which temperature the dihedral angle approaches zero. Silicon has little effect on this change. Aluminum, oxygen, and manganese all modify the temperature of sulfide network formation to a higher value. The microstructures which result and have significance in relation to hot-shortness are discussed. SULFIDE inclusions in steel were recognized by metallurgists before the turn of the century. Considerable attention has been paid to them, and numerous studies have been made on the working properties of steel as affected by them. It has been suggested that ho t-shortness of steel is due to the presence of an enveloping liquid sulfide film at the grain boundaries of the steel in the range of the hot-working temperatures. However, several facts have been observed in commercial steels which do not seem to be completely consistent with this explanation: 1) the frequent absence of continuous films of sulfide as observed under the microscope, 2) the absence of hot-shortness in some high sulfur and resulfurized steels, and 3) the limitation of hot-shortness to a definite temperature range. The role that manganese plays in steel to eliminate hot-shortness is well known, but the theory behind it is still under question. Moreover, the effect of de-oxidizers such as aluminum and silicon, and the effect of oxygen are still not clearly known. In this study, the effect of heat treatments and of additions of manganese, aluminum, silicon, and oxygen upon the distribution of sulfide inclusions in iron was investigated. Both the as-cast and the heat treated structures were studied, using microscopic and autoradiographic techniques. Part of the results were interpreted in terms of Smith&apos;s&apos; concept of microstructure. Review of Literature Metallurgists used to consider sulfide inclusions as suspended particles. It was Wohrman&apos; who first pointed out that sulfide inclusions are soluble in liquid iron. Many observed facts may be understood on the basis of this concept of solubility. Wohrman found that small castings contain small inclusions. and larger castings contain larger ones. Also, inclusion sizes are smaller near the chilled surface. For the same size ingot, the average inclusion size in a given heat of steel depends upon the rate of solidification. That is, with slow solidification, enough time for precipitation and agglomeration of these

Jan 1, 1957

By N. Brown, R. Kossowsky

Plain carbon steels with 0.48 and 0.95 pct C were quenched and tempered at 705°C to produce carbide dispersions with spacings on the order of 1 p. The morphology of the structure consisted of a carbide-dislocation network. The strengthening due to the dispersion was found to vary linearly with M-½ where M is the mean free-ferrite path determined by the entire network. No preyield microstrain preceded the upper yield point. After prestraining, the lowest stress at which dislocation movement could be detected was 104 psi; this frictional stress was independent of the dispersion and prestrains up to 6.5 pct. The Cottrell-Petch equation for grain-size strengthening was used to discuss the dispersion strengthening in this investigation. The results support an impurity mechanism for the upper yield point rather than one based on the Johns ton- Gilman theory. IT was pointed out by Gensamerl that the mean free path in the matrix is the important variable which controls the degree of dispersion strengthening. Gensamer&apos;s data on steels showed a linear relationship between the yield point and the logarithm of the mean free-ferrite path. The first theory was by Orowan,2 who suggested the mechanism of dislocations bowing between particles, with the resulting relationship that where a is the yield point, P is the distance between particles, and G is the shear modulus. The Orowan equation applies to that range of dispersion where P is large compared to the particle size and the particles are not coherent, so that the matrix is essentially free of internal stresses. As was pointed out by Orowan, there are different degrees of dispersion which, in turn, will influence the strength-controlling mechanism. However, in this investigation, we wish to confine ourselves to the region of coarse dispersion, where the Orowan mechanism should, intuitively, be applicable. It was soon evident that the data, which existed at about the time that the Orowan theory was proposed, did not agree with the Orowan equation in that the actual strengthening was always greater than the theoretical predictions. Thus, Fisher, Hart, and pry3 modified the Orowan theory by suggesting that the Orowan process took place in the microstrain region preceding macroscopic yielding and the subsequent, rapid work hardening in the form of residual dislocation loops around the particles largely determined the observed macroscopic yield point. The F-H-P theory stated that the increment of strengthening due to the work-hardening mechanism was proportional to f3/2 where f is the volume fraction of the precipitate. F-H-P used data by Shaw, Shepard, Starr, and Dorn4 on A1 3-5 pct Cu to support their theory. Roberts, Carruthers, and Averbach5 were the first to make a microstrain study of dispersion strengthening, and they found that for steel the Gensamer relationship was obeyed. Hayman and Nutting6 suggested that in the case of tempered steel 1) the ferrite grain boundary was the primary obstacle and 2) the carbide particles simply formed part of the grain boundary obstacles. They found that the strength varied as G"" where G is the ferrite grain size. Turkalo and LOW&apos; determined the structure of quenched and tempered plain carbon steel using a replica technique; they concluded that the carbide particles did not necessarily lie in the ferrite grain boundaries. When they defined the mean free-ferrite path as being determined by both particles and the ferrite path boundaries, their data obeyed the Gensamer relationship. Meiklejohn and skoda8 showed that the strengthening from iron particles in mercury was a function of the particle size and the distance between particles. Dew-Hughes9 explained the Meiklejohn and Skoda results by the following theory: 1) grown-in dislocations which surrounded the particles were produced by the thermal stresses during the time the material was cooled to the testing temperature, and 2) the observed strengthening was associated with the cutting of the grown-in dislocations by the glide dislocations. Ansell and Lenel10 proposed a theory in which the glide dislocations pile-up or surround the particle until the number of dislocations in the pile-up is sufficient to yield or fracture the particle. The resulting theory says that the yield point varies as p-1/2, where P is the distance between particles. The Ansell-Lenel theory is almost identical to the

Jan 1, 1965

By J. H. Smith, H. W. Paxton

X HE recent investigation of Butler, McCabe, and paxton&apos; on the vapor pressure of manganese gas in equilibrium with Mn-Fe alloys has been extended to include the iron-rich solutions and alloys in the two phase equilibrium region. The study of the phase equilibrium by Kurnakov and Troneva2 and the extensive reviews of the Mn-Fe system by Hansen,3 and Hellawe114 are not in agreement with regard to the location and extent of the equilibrium between the solid phases of fcc y and complex P in the temperature range above the eutectoid temperature of approximately 975Kwhere 0 decomposes to y and bcc a. An evaluation of the existing equilibrium data is confronted with the conflicting results presented by various investigators who used techniques requiring a quenching treatment to retain the high-temperature equilibrium or encountered temperature hysteresis during thermal analyses. The difficulty of suppressing the transformation of the manganese-rich concentrations of the y-solid solution during quenching has been well etablished.&apos; To avoid this uncertainty the phase equilibrium was investigated at temperature by measuring the partial pressure of manganese gas in equilibrium

Jan 1, 1962

By R. A. Swalin, A. H. Geisler

THIS study represents an investigation of the effect of annealing temperature on the texture of drawn molybdenum, iron, and an iron alloy containing 14 pct Al. The effect of temperature on annealing textures has not been widely investigated in the past. One of the obstacles in making such a study using usual X-ray diffraction techniques results from the

Jan 1, 1957

By J. S. Kirkaldy, D. G. Fedak

The extra degree of freedonz introduced by a second independetzt concentration in a tenzary system gives rise to the possibility of unstable planar phase interfaces in semi-infinite diffision layer couples. Diffusion paths which pass continuously in and out of too-phase regions of the phase diagram but which are not coincident with tie-lines give rise to super saturated zones which may be either adjacent to or isolated from planar phase interfaces, with corresponding nonisolated or isolated precipitates. Nonisolated precipitates are equivalent to morphological development of the interface. Selected couples in the ternary systems Fe-Ni-Cr and Cu-Zn-Sn have been examined nzetallographically and ifz the latter case both isolated and uo~zisolated precipitates have been observed. The diffusion path in one of the couples showing interface morphological developtnent has been examitled using electron probe microanalysis. IGNORING the spurious effects of preferential grain boundary diffusion and anisotropic crystal growth7 it can be unequivocally stated that it is impossible for a binary isothermal diffusion couple constructed of two unsaturated phases to sustain a nonplanar phase interface. Consider for demonstrative purposes the schematic phase diagram of Fig. l(a). Given an initial flat phase interface, semi-infinite boundary conditions and the internal boundary condition fixed by the constitution diagram, xB = xB(T), the unique solution of the diffusion equation requires a persistent flat interface. No other solution is possible. If, however, we anticipate the involvement of surface tension, then the internal boundary condition must be written xB = xB (T,Y) where r is the radius of curvature of a hypothetical nonplanar interface. The introduction of a new parameter such as r can be equivalent to the release of an internal constraint, so that a stable nonplanar interface may be possible after all. Consider a perturbation to the interface as indicated in Fig. 1(b). According to the Ostwald-Freundlich equation: which is applicable to a system of this constitution, the solubility of A in the matrix ß ,xB (Y), at a point of curvature r is given by where Va is the molar volume of the a-phase, R is the gas constant, and a is the interfacial tension. Since the right hand side is positive, xB(r) >xB cm, as indicated in Figs. 1(a) and 1(c). Accordingly, the perturbation will carry the interface concentration in a direction which is opposite to that which would sustain local equilibrium. Such a perturbation is necessarily moderated and the system is returned to its initial condition. This result is general for all binary couples since we can regard an interfacial perturbation as an attempt to precipitate within un-

Jan 1, 1962

By J. E. Harris

By elimination of other possible nucleation processes, it has been demonstrated, for commercially pure magnesium and a Mg-Al alloy, that at stresses less than that necessary for triple-point cracking creep cavities are most probably nucleated heterogeneously at second-phase particles. Evidence for the existence of such particles is presented and the role of grain boundary sliding in the nucleation process is examined quantitatively. DURING creep deformation of polycrystalline magnesium and its dilute alloys in the temperature range 0.45 to 0.7 Tm (Tm = absolute melting temperature) cavities form mainly along grain boundaries oriented normal to the stress axis and failure eventually occurs by their growth and impingement.&apos; The possibility of low-ductility creep failure of magnesium-alloy reactor cans during service has prompted a number of studies of cavity formation in these materials.2-5 In this paper divergent theories of cavity nucleation6-10 are examined critically and conclusions drawn regarding the most probable mechanism of formation of cavities in magnesium. The paper is divided into two parts. The first section consists of the review and quantitative assessment of the possible role of grain boundary sliding in the nucleation process. In the second part an experimental program is described where an electron-microscope technique has been used to determine if second-phase particles exist in as-received commercially pure magnesium and in a magnesium alloy 1) THEORETICAL REVIEW Possible nucleation sites for creep cavities are: a) high-angle grain boundary triple points,11-14 b) subboundary/grain boundary intersections,15-18 c) ledges in the grain boundary, 19-25 d) second-phase particles. 9,26-30 Each of these possibilities is now considered with special reference to deformation of magnesium. 1.1) Triple-Point Cracking. The stroh31 condition to nucleate fracture is: " > vr [1] where ss = applied shear stress, ? = surface energy, C = shear modulus, L = length of sliding interface. This relationship is independent of the nature of the interface and it is possible to calculate the stress concentration at the end of a sliding high-angle grain boundary and thus deduce, approximately,* the minimum applied stress necessary to nucleate triple-point cracking. Such theoretical predictions for Nimonic alloys have been made by McLean13 and found to agree quite closely with the minimum stress determined by experiment. Stresses capable of nucleating triple-point cracking should also be sufficient to nucleate fracture at a grain boundary due to intragranular slip, for the lengths of sliding interface in the two cases are approximately equal. Thus the minimum stress for triple-point cracking should represent a demarcation between failure due to general "cracking" and that due to cavitation. Hauser, Landon, and Dorn32 have demonstrated that for polycrystalline magnesium in the temperature range 78° to 298°K the fracture stress is inversely proportional to the square root of the mean grain diameter. As pointed out by stroh31 this result indicates that Eq. [I] describes the fracture characteristics of magnesium at low temperatures. Heal3 has reported that for rapid deformation (112 pct hr-1) of polycrystalline magnesium the transition from cracking to cavitation occurs in the temperature range 175" to 275°C. He also presented the fracture-stress values for the same material tested under similar conditions. From Eq. [I] taking G = 1.3 x 10" dynes , ? = 600 ergs . cm-2,33 and L = 0.017 cm, a Stroh-McLean13,31 tensile stress of -266 kg. cm-2 is calculated, corresponding to a transition temperature of -190°C; this is in

Jan 1, 1965

By E. Hornbogen

The deformation mechanisms of a iron-phosphorus alloys were compared at 20oand —196°C. Alloying with phosphorus increases the resistance to slip, but has little effect on the resistance to twinning. The stress for onset of twinning is nearly independent of temperature, but there is an increasing tendency for cleavage along (112) twin boundaries with decreasing temperature and increasing phosphorus content. FIVE iron-phosphorus alloys and one high-purity iron (0.004 pct C, 0.004 pct N, 0.05 pct O) were vacuum melted and cast, then homogenized for 6 hr at 1100oC and water-quenched. Single crystals were cleaved from the coarse grains produced in this manner. The hardness was measured* on polished (100) surfaces of the crystals at 20" and -196°C. Laue back-reflection patterns indicated a deviation of not more than 3 deg from coincidence of the {100} plane with the surface. The deformation mechanisms were studied by relief effects on the polished surfaces. Yield points in compression (0.5 pct offset) were measured with polycrystalline material. At 20°C the addition of phosphorus to a iron leads to a change from slip to twinning as the main deformation mechanism, Figs. 1(a), (b). Between 2 and 4 at. pct P slip and twinning occur simultaneously. In alloys with more than 4 at. pct P twinning is the main deformation mechanism and slip was observed only in the neighborhood of twin intersections. All cracks at 20oC were on (100) planes, some initiated by twins.&apos; From measurements made at-196oC, hardness and yield points of all the alloys were nearly constant and the same as the hardness of high phosphorus alloys that deformed by twinning at 20°C, Figs. 2 and 3. In the high-purity iron, plastic deformation at -196°C occurred by both slip and twinning, but deformation in the iron-phosphorus alloys appeared to be entirely by twinning. In the high phosphorus alloys a large number of cracks formed along the (112) twin boundaries and at intersections of twins, in addition to the (100) cleavage, Fig. 1(c). DISCUSSION In , iron, plastic deformation can occur either by slip or by twinning, depending upon composition,

Jan 1, 1961