Search Documents

By Gilbert Santoro

In this study tantalum carbide filaments of various compositions in the fcc region were prepared by heating a tantalum wire in a measured amount of hydrocarbon vapor. Such properties as tensile strength, transverse-rupture strength, microhard-ness, lattice parameter, electrical resistivity, and magnetic susceptibility were measured as a function of carbon content. Some of these properties showed a maximum or a minimum between a carbon-to-tantalum molar ratio of 0.80 and 0.85, the composition range at which the color changes from metallic gray to gold. The recent literature has shown that in the large homogeneity range for the fcc phase of the Ta-C system there is a marked variation for such properties as microhardness,' electrical resistivity, ' thermodynamic properties,z'3 lattice parameter and superconductivity. In addition to the technological interest of these variations within a single phase, important theoretical benefits may ensue from a continuous investigation of properties vs stoichiometry in tantalum carbide and other refractory defect compounds, for example the effect of the metal-metal distance and crystal structure upon bond formation and electronic structure. Whether there is a similar variation of the tensile strength is of practical importance. Of theoretical interest would be the knowledge of how the magnetic susceptibility varies with carbon composition. Both of these properties, as well as the transverse-rupture strength, were determined for tantalum carbide filaments in the fcc phase region. The lattice parameter, the electrical resistivity, and the microhardness were also investigated and compared with values appearing in the literature. EXPERIMENTAL PROCEDURE Material Preparation. Tantalum carbide specimens of various carbon content were prepared by statically carburizing high-purity tantalum filaments in measured quantities of pure hydrocarbon gas. The filaments, which were 10 mil in diameter and 20 or 40 cm long, were heated by their own resistance at temperatures from 1800" to 2200°C using alternating current in some cases and direct current in others. Tantalum wire from two sources was used. One had a reported purity of 99.96 wt pct Ta. The ingot from which this wire was drawn had been electron beam-melted as the final step in its purification. The reported purity of the other wire, which was prepared by a powder metallurgical process, was 99.88 wt pct Ta. The impurities of both tantalum sources are listed in Table I. Spec-trographic-grade toluene or research-grade propane was used as the source of carbon. The apparatus for the carburization of the filaments is shown schematically in Fig. 1. The system was evacuated to 1 x l0-' mm of Hg when using the electron beam-melted tantalum and to less than 1 p when using the less-pure tantalum. Neither the difference in the base vacuum, nor in the hydrocarbon gas, nor in the tantalum filaments resulted in any detectable difference in the properties studied in this work. However, only the carbides prepared from the higher-purity tantalum were used in the magnetic-susceptibility determinations. Once the base vacuum had been reached, the system was flushed with the hydrocarbon and re-evacuated. For any desired composition of the carbide, hydrocarbon gas was allowed to leak into a constant-volume flask to a predetermined pressure. These pressures were measured by a Cartesian diver-type mercury gage with a range from 0 to 20 mm and with a scale expanded to nine times. The hydrocarbon gas was allowed into the reaction tube and the filament was quickly raised to the reaction temperature. The slack in the filament due to thermal expansion was taken up by drawing out the movable electrode with a screw mechanism. The filaments were kept at temperature from a few minutes to 200 hr. In the majority of cases the heating time was 6 hr. The reaction tube was cooled by cascading water on its outer surface. By means of an ammeter and a voltmeter the electrical resistance at the reaction

Jan 1, 1963

By F. H. Buttner, E. R. Funk, H. Udin

A. P. Greenough (University College, swansea, Great Britain)—I have recently made some experiments on the deformation of silver wire at high temperature in an atmosphere of oxygen-free nitrogen. The observa-tions which 1 made confirm the main conclusion of this paper, that the most satisfactory mechanism so far suggested to explain the deformation which takes place

Jan 1, 1953

By E. J. Dulis, A. Kasak, R. C. Westgren

The potential of uirought tungsten- and tantaluw-rich alloys of the W-Ta-Mo-Cb system was investigated for high-strength structural applications above 2500° F. Appreciable strengthening of tung-sten and tantalum—essentially attributable to solid-solzction effects—was obtained with binary, ternary, and quaternary alloys. Tensile strengths as high as 67,000 psi were achieved at 3000 OF. ThE quest for wrought structural materials which possess good strength properties at temperatures above 2000°F has led to a considerable research effort during the past decade. In addition to exploring the potential of various high-melting-point refractory metals (such as molybdenum, columbium, tantalum, and tungsten) for very high-temperature structural applications, alloy-development programs have been undertaken to achieve greater strengths than could be achieved with unalloyed refractory metals. The methods of strengthening refractory metal alloys have included both solid-solution and dispersion strengthening. General relationships among the relevant properties (melting point, recrystallization temperature, and high-temperature strength) of refractory metals indicate that the highest strengths at temperatures of 2500°F or higher would be obtained with tungsten-or tantalum-base alloys. Therefore, the present investigation was undertaken to determine the high-temperature strength potential of solid-solution strengthened alloys based on the binary system W-Ta; to effect further strengthening, minor additions of molybdenum and columbium (at the 6 and 12 pct levels) were made. The portion of the W-Ta-Mo-Cb quaternary alloy system of interest is shown schematically in Fig. 1. The component metals—W, Ta, Mo, and Cb—have a bcc structure at all temperatures, and their binary systems are mutually completely soluble.' Complete solid solubility in the W-Ta-Mo and W-Ta-Cb alloy systems has been demonstrated,' and, therefore, it was expected that the quarternary alloys of the system would also exhibit complete solid solubility at all temperatures. In the virtual absence of contamination by interstitial elements, all the alloys would be truly solid-solution strengthened. Twenty specific compositions of this investigation included binary, ternary, and quaternary alloys of the W-Ta-Mo-Cb system as well as unalloyed tungsten and tantalum. The compositions are shown in Table I. EXPERIMENTAL PROCEDURE Consumable-electrode vacuum-arc melting with ac power was used to produce small laboratory-sized, cylindrically shaped ingots (1-1/4 in. in diameter and 2 to 3-1/2 in. long) of the twenty compositions. A furnace was specially constructed to melt as many as four electrode rods simultaneously into molds lined with tungsten or tantalum sheet. High-purity rods of tungsten, tantalum, molybdenum, and columbium were used for consumable electrodes; the diameter of each rod was determined by the desired weight percentage of the component metal in a given alloy. The details of the construction and operation of the melting furnace will be discussed in another p~blication.

Jan 1, 1964

By J. A. Berger, R. J. Towner

The pjPocesses of polygonization and subgrain growth were followed in slightly stretched 99.99 pct A1 single crystals heated for cumulative times at 400°, 500°, and 600°C. Changes in sub-grain size and boundary angle were determined from measurements on X-ray micrographs. CAHN1, 2 studied polygonization in stretched and heated aluminum single crystals of 99.99 pct A1 using various techniques, including etch pits, Laue patterns, and a slight restretching of heated specimens to reveal small changes in lattice orientation by the direction of new slip lines. He found that kink bands, which had well-defined boundaries lying in a plane perpendicular to the slip direction (at least in the early stages of deformation), formed during stretching. Also, he noted that bending occurred about the <211> axis lying in the (111) slip plane perpendicular to the <110> slip direction. His studies of polygonization were largely confined to the kink bands rather than to the weakly bent matrix regions between bands. The minimum temperature required to bring about polygonization was established at about 450 "C. Guinier and Tenevin used a focusing Laue X-ray diffraction technique to study polygonization in aluminum single-crystal specimens of 99.99 pct purity. Stretching the crystals 5 pct in tension caused a widening of the focused Laue spots. After heating for 4 hr at 450°C, their method revealed no change in the specimen. Above 450°C polygonization was detected and further annealing near 600°C led to subgrain growth. They concluded that the orientation of the crystal relative to the axis of deformation had no marked effect on polygonization. Gay and Honey-combe4 using an X-ray microbeam technique found that polygonization did not occur in a stretched aluminum crystal heated at 250oC, although some decrease in the yield strength occurred. When the temperature was raised to 475oC, the asterism became broken up as a result of polygonization. Honeycombe5 noted that reflections on X-ray mi-

Jan 1, 1961

Jan 1, 1941

Jan 1, 1933

GENTLEMEN Herewith are transmitted reports from the Treasurer and of the principal standing committees of the Institute. To these special reports members are referred for details as to the year&apos;s work. Despite the unfavorable business conditions obtaining throughout the year, the Institute was able to carry on its various activities without curtailment and without drawing on the surplus accumulated through previous years. In fact, small additions were made to the Life, Member¬ship and various other funds. It is highly desirable that such additions should continue to be made, especially to the Life Membership fund, for reasons reported last year. At present, money must be used from current receipts in order to enable the Institute to fulfill its obligations to those who on joining the organization commuted their dues by a single payment. In addition, with the passage of years the number increases of those who have paid dues forty years or more and who, by reason of age or dis¬ability, are unable longer to practise their profession. These men have supported the Institute through their active professional life and it would be a pity to lose them as members through resignation or for failure to keep up their dues. In accordance with the By-laws the Board has authority to advance such members, on application, to the Honor Roll of Senior Members and to relieve them from further payment of dues. It has been the policy of the Board to do this liberally, but to keep up this, as well as to meet other obligations, it is necessary for money to be provided. It has been estimated by the Treasurer that nearly $50,000 additional should be placed in the Life Membership fund as soon as possi¬ble to meet these obligations without using current income and to that end it is necessary, not only to avoid running behind currently but to earn, if possible, some surplus each year. The small amount transferred to the Life Membership fund from surplus this year was, as a matter of fact, made possible by certain members paying personally bills that were properly chargeable to the Treasury. Such generosity is common among those active in Institute work and probably no year would have closed with a surplus except for it.

Jan 1, 1923

United Engineering Trustees, Inc. W. D. B. MOTTER, JR., &apos;40 A. L. QUENEAU, &apos;41 ALBERT ROBERTS, &apos;39 The Engineering Foundation GEORGE D. BARRON, &apos;40 F. F. COLCORD. &apos;42 A. L. QUENEAU, &apos;41

Jan 1, 1939

United Engineering Trustees, Inc. GEORGE D. BARRON ARTHUR S. DWIGHT R. M. ROOSEVELT The Engineering Foundation H. C. BELLINGER E. DEGOLYER J. V. N. DORR

Jan 1, 1932

United Engineering Trustees, Inc. ARTHUR S. DWIGHT GEORGE D BARRON J V. N DORR Engineering Societies Library Board ROBERT PEELE PHILIP W. HENRY GEORGE C STONE JOSEPH E. POGUE The Engineering Foundation H C BELLINGER GALEN H CLEVENGER J V N DORR

Jan 1, 1923

United Engineering Trustees, Inc Engineering Foundation Engineering Societies Research Board Other Committees United Engineering Trustees, Inc. ARTHUR S. DWIGHT GEORGE D. BARRON J. V. N. DOER Engineering Societies Library Board ROBERT PEELS PHILIP W. HENRY GEORGE C. STONE JOSEPH E. POGUE The Engineering Foundation H. C. BELLINGER GALEN H. CLEVENGER J. V. N. DORR

Jan 1, 1929

By Roxanne Scott

Outline ? Overview of Community Investment in the Mining Sector ? Emerging Good Practice: ?Strategic Integrated Community Investment? ? Assessing Local Context: ? Institutional Assessment ? Partnership Assessment Approaches to Community Investment Isolation: No proactive engagement in community development Ad hoc philanthropy: small infrastructure, sponsorships, donations Strategic philanthropy: Community proposes options for development Company decides what to do and carries it out, e.g. building schools, health posts, roads Strategic integrated community investment: ? Aligned with government/community development goals and priorities ? Communities and government involved in decisions and execution ? Focused on training and capacity building ? Partnerships ? Continuation in absence of company support Measured returns on investment

May 1, 2010

By Charles H. Wells

This paper presents a review of the state of the art in coal preparation plant instrumentation and a discussion of automation practice that could be applied based on current mineral beneficiation experience and demonstrated foreign technology in coal washing plants. Specific e-mules of applications of remotely controlled slurry values, pneumatic and electronic field transmitters, computers for control and data logging, and on-line analytical instrumentation are given. A program, to demonstrate this technology is described.

Jan 1, 1980

By Swapan Ghosh, Amitava Sengupta, Proloy Das

Ferro-alloys are very important ingredients used for making of quality steel with desired composition. In view of high demand in various types of ferro-alloys, it has become necessary to produce the same efficiently, safely and cost-effectively with consistent quality maintaining the anti-pollution norms. To achieve this goal, it is necessary to adopt latest process/equipment with the state-of-the-art instrumentation and automation system. A Programmable Logic Controller (PLC) based automation system with suitable Human Machine Interface(HMI) terminals along with intelligent field mounted sensing/control devices allows to monitor and control the complete plant effectively with optimum deployment of man-power. In association with this, use of process optimization controllers enables to achieve specialised functionalities of the submerged arc furnaces like material management, lining management, electrode management, power management, overall production management etc.

Jan 1, 2007

By H. Mori

The session chairman, Dr. H. Mori, welcomed the delegates to Discussion Session 8. AUTHORS PRESENTATIONS 1 . G. Price, Building Research Establishment. UK Mr. Price expanded on the content of his paper and presented elements of various case histories of bored piles instrumented by the Building Research Establishment. In particular, the interpretation of data from instrumented piles is critically related to: (i) the construction process (ii) concrete stiffness and variability (iii) the effects on the pile due to installing instruments The main role of the instrumentation in the examples presented was to establish pile performance under service loading conditions. Of particular interest is the mobilisation of skin friction and soil shear modulus.

Jan 1, 1991

By Francis Otuonye

Rock fragmentation by blasting still remains the most common and cost-effective method of excavating hard rock in mining and tunneling operations. During blasting, the dynamic stresses induced by the detonation of the explosive, in addition to fragmenting the rock in the vicinity of the blast, may fracture the rock at considerable distances from the point of detonation of the explosive. The fractures can result in reduced mine safety, increased costs to support the opening, low productivity and perhaps high ore dilution. Besides the dynamic stresses produced in the rock, air blast overpressure pulses are generated and propagate through the network of underground mine openings. The waves, unable to spread out spherically or hemispherically like blast waves from surface blasting, are forced to propagate by reflection from the roof, ribs and floor down the drift. Blast wave focusing can occur and produce intense shock waves that could damage ventilation barriers such as cement block stoppings.

Jan 1, 1992

By J. D. Noll, S. E. Mischler

Measurement and sampling of diesel particulate matter in mine air presents a challenge due to the complexity of the diesel aerosol. The results of a series of tests carried out by the National Institute for Occupation Safety and Health, Pittsburgh Research Laboratory, in an underground mine were used to evaluate several measurement methods that are currently used to characterize particulate matter emitted by diesel-powered equipment. This paper presents an overview of these techniques and examples of the results along with a discussion of the advantages and information gained by each technique. The measurement methods discussed include particle size measurements using a scanning mobility particle sizer, total particulate matter measurements using a tapered elemental oscillating microbalance, a size selective sampling method for workplace and personal exposure assessment and a size-selective high volume sampling method for carbon analysis.

By Robert F. Droullard

The U. S. Bureau of Mines (USBM) has investigated instrumentation and methods for measuring exposure to radon daughters in underground mine atmospheres. Both personal and area monitors have been studied through in-house and contract research. A field study in uranium mines identified some reliability problems that required additional work for the personal dosimeter systems. Improved versions of continuous working level detectors have been developed and tested for use as area monitors in underground mines. Test results for the personal and area monitors were satisfactory for underground mine applications.

Jan 1, 1981

By T. A. Marcotte, D. J. Bobrow, S. Vaghar

This paper discusses the geotechnical instrumentation program on the Central Artery/Tunnel Project, in Boston, Massachusetts. Particular attention is given to a state of the art Graphic Information System (GIS) application which has been developed for rapid analyses and reporting of data. This application will see extensive use during the ongoing complex downtown tunnel construction. The excavations in soft ground require cuts of up to 120 feet deep and 250 feet wide. Deformation and groundwater monitoring instruments have been installed to monitor the stability of the excavation support systems and the abutting buildings. The use of this application is illustrated with an example from an ongoing contract.

Jan 1, 1997

The #3 Shaft at Brunswick Mine, Bathurst, New Brunswick, Canada, intersects a soft graphite zone just below the 3400 Level. Ground movement within this zone causes the concrete liner of the shaft to be deflected towards the shaft?s interior, affecting the steel framework of the conveyance. In some areas, the clearance between the cage and the liner has been reduced to less than 2 cm, which is a concern. An innovative surface-mounted extensometer was designed in 2008 to monitor potential movements of the shaft?s liner. Four such novel extensometers were installed in the shaft for the surveillance of a particularly critical 3.0m by 5.5m area. This article describes the approach taken to instrument the shaft, the principle of the new extensometer, as well as the performance of the instrumentation following its installation.

May 1, 2009