Search Documents

By Lev Filippov, Vyacheslav Severov, Inna Filippova

"Reverse cationic flotation is a very efficient method of beneficiation of oxidized iron ores when you need to separate hematite and quartz. This method can be also applied to reduce silica content in the magnetite concentrates obtained by wet low-intensity magnetic separation. However, cationic flotation in this case is less effective due to the presence of Fe-Mg-Al-bearing silicates as amphiboles in magnetite ores. These silicates are concentrated in magnetic products and determine the difficulties of their separation from iron oxides when amines and starches are used as collectors and depressants, respectively. The recalculation of the results of the electron microprobe analysis of three calcic Fe-Mg-Al-bearing amphiboles used to characterize cation distributions in structural units and to obtain structural formulas in accord with stoichiometric limits was conducted. The Mössbauer spectroscopy was used to examine the validity of the empirical estimation of cation distributions in amphiboles. The studied samples are metamorphic pargasite and ferrotschermakite and volcanic magnesiohornblende. The crystallographic analyses of the amphibole samples exhibited their heterogeneous surfaces explaining worse floatability of amphiboles with dodecylamine at pH 10. The electrokinetic measurements showed that the position of the isoelectric point of amphiboles is related to a substitution of Al3+ for Si4+ in tetrahedral sites and to an amount of Mg2+ cations in octahedral sites. Thus, the dodecylamine adsorption onto amphiboles through electrostatic interactions is mainly affected by a distribution of these cations in tetrahedral and octahedral sites of amphiboles. In addition, the effect of starch on the depression of Fe-Mg-Al-bearing amphiboles during flotation can be attributed to the presence of metal ions on the amphibole surface, which are capable of forming strong chemical complexes with starch molecules."

Jan 1, 2014

By Ray Schmahl

The Glenwood Canyon is a 13 mile long river gorge formed by the Colorado River approximately 2 miles East of Glenwood Springs, Colorado and approximately 150 miles West of Denver Colorado, (See Drawing #1). The canyon walls rise some 800 feet from the river elevation on either side of the river. The South-side river bank is occupied by the Denver and Rio Grande Western Railroad. The Northside is currently occupied by completed sections of Interstate 70 and US Highway 6. The railroad was built in the late 1800's and a hydroelectric power generating station was built in about the center of the canyon in the early 1900's. The Highway 6 platform was completed in the 1930's. The design and alignment for Interstate 70 thru Glenwood Canyon began in the early 1970's. The Highway thru Glenwood Canyon was designated a scenic Highway by the United States Congress, thereby allowing certain deviations from standard Interstate requirements. Environmentalists objections to the construction of Interstate Highways thru Glenwood Canyon resulted in especially careful design to avoid adverse environmental impacts. As a result, in many areas the new Highways will have restored the canyon to its more native configuration than what was the case in the building of the US 6 Highway platform.

Jan 1, 1990

By S. Akhtar

Interstitial compounds of iron, cobalt, and nickel, and their binary and ternary mixtures with silver, gold, palladium, and platinum were prepared and tested as fuel cell catalysts. The first step in the preparation of the interstitial compounds consisted of preparing finely divided metals. This was done either by the Raney method or by reduction of precipitated hydroxides of the metals. The finely divided reduced metals were then treated with carbon-and/or nitrogen-containing gases to prepare their carbides, nitrides, and nitrocarbides. The materials were tested for cathodic activity towards O2 and for anodic activity towards H2, C3H8, NH3, CO, and N2H4 in acid and alkaline electrolytes at 25° to 90° C in half-cell assemblies. Samples of carbided and nitrocarbided INi-lAg-1Au were about one fifth as active as Pt-black in the reduction of O2 in 35 percent KOH solution, whereas the activities of several interstitial preparations exceeded the activity of Pt-black in the reduction of O2 in 12M KOH containing N2H4. Nitrocarbides of x-Fe2C, 3Ni-1Au, and 1Ni-3Au were effective catalysts for oxidizing N2H4 in liquid NH3 containing NH4SCN. Corrosion of the catalysts by electrolytes was severe in many cases.

Jan 1, 1970

By D. Tesh

The mining industry worldwide is facing a tremendous shortage of minerals engineers in all fields of specialization. For instance, in Australia the skills shortage in the mining industry has been identified as one of the top risks facing the mining industry. In Namibia most minerals engineers employed are expatriates, with some being Namibians who studied abroad. The minerals engineering programmes at the Polytechnic of Namibia are still in their infancy. These programmes were designed to meet the mining industry skills needs. Being young has its advantages in that lessons can be learnt from older minerals education institutions that went through similar challenges. However, this does not imply just copying and implementing their approaches, since the context differs and, to ensure sustainability of the minerals education programmes, curricula have to be customized to the local context. This paper reviews the interventions made by the Polytechnic of Namibia in order to ensure the sustainability of its minerals education programmes. The methodology consisted of an extensive literature review, a status quo analysis of the mining and process engineering department, identifying the gaps between the current state and desired state, and mapping the goals and strategic actions required to progress to the desired state. The following factors were identified as major threats to the sustainability of minerals education at the Polytechnic of Namibia: the quality of students, low student enrolment rates, low pass rates in science and mathematics, shortage of academic staff, dwindling government funding, and limited involvement of the mining industry. The major outcomes of this research comprise the detailed strategic actions employed by the Polytechnic of Namibia to address the threats to sustainability of its minerals education programmes.

Jan 1, 2014

By Tim O’Neil

What prompted the merger of the two long-established American Mining Congress/National Coal Association (AMC/NCA) groups that combine the coal, hard-rock, industrial- and agricultural-minerals sectors of mining? Both associations have been facing similar stresses for several years - structural changes in their respective industries, the changing personality and role of government and well-financed and organized opposition groups. In 1993, the AMC board of directors undertook efforts at reorganizing the association. One board member, who serves on both boards, suggested it might be time to give serious consideration to merging the organizations. This is an idea that had been discussed more or less informally at least three times during my tenure at NCA. Negotiations toward a merger began after that and were consummated in February of this year.

Jan 1, 1995

The Oregon-Idaho graben evolved after widespread tholeiitic flood basalt volcanism associated with the arrival of the plume head of the Yellowstone hotspot beneath southeastern Oregon approximately 17 - 16 Ma. The north- to north-northeast-trending, 50 km-wide graben evolved between 15.5 and 10.5 Ma during east-west extension. The graben is part of a middle Miocene back-arc rift (1100 km long) that includes the northern Nevada rift, the Baker and LaGrande grabens, and the Chief Joseph dike swarm of the Columbia River Basalt Group. The graben ceased to be a volcanotectonic depression as the cross-cutting western Snake River plain began to evolve at approximately 10.5 Ma. At about 14.3 Ma and continuing to approximately 12.6 Ma the Oregon-Idaho graben began to break up into subbasins that were bounded by intragraben fault zones. The break up was accompanied by a change to calc-alkaline volcanism that persisted within the Oregon-Idaho graben until 8.1 Ma, approximately 2.5 million years after subsidence within the graben ceased. Three intragraben fault zones have been identified and a fourth is inferred. The easternmost, the Devils Gate fault zone, coincides with the magmatic axis of the graben at approximately 14.3 Ma. By approximately 13.5 Ma the magmatic axis had shifted to the west along the Dry Creek Buttes and Wall Rock Ridge fault zones. A diffuse magmatic axis developed at approximately 12 Ma farther to the west where the fourth intragraben fault zone is inferred. In addition to serving as conduits for the ascent of basalt, basaltic andesite, rhyodacite, and rhyolite magmas, the zones focused the discharge of large geothermal systems. The intragraben fault zones display a common evolutionary pattern. The 2 to 3 km-wide zones initially control the distribution of facies in volcaniclastic sediments and the location of basalt hydrovolcanic vents. During this stage, the fault zones may have had no surface expression other than a low elevation change on a relatively low-relief landscape. As relief developed by continued deformation along the fault zones, strike-length of individual faults increased and weakly consolidated volcaniclastic sediments, silicified sediments and hot-spring sinter, and palagonite were eroded from the uplifted blocks and deposited in neighboring subbasins. It is during this stage that the large hot-spring precious-metals bearing prospects evolved. Displacements of over 150 m on a few faults within the zones and possible reversal of the sense of displacement along the zones occurred in this final stage of development. Locally, the fault zones were remobilised during the subsidence of the cross-cutting western Snake River plain. The intragraben fault zones within the Oregon-Idaho graben illustrate the relations among syntectonic volcanism and sedimentation and the evolution of geothermal systems within continental rift systems.

Jan 1, 1995

The Oregon-Idaho graben evolved after widespread Uwleiitic flood basalt volcanism associated with the arrival of the plume head of the Yellowstone hotspot beneath southeastern Oregon approximately 17-16 Ma. The north- to north- northeast-trending, 50 km-wide graben evolved between 15.5 and 10.5 Ma during east-west extension. The graben is part of a middle Miocene back-arc rift (1,100 km long) that includes the northern Nevada rift, the Baker and LaGrande grabens, and the Chief Joseph dike swarm of the Columbia River Basalt Group. The graben ceased to be a volcano- tectonic depression as the cross-cutting western Snake River plain began to evolve at approximately 10.5 Ma.

Jan 1, 1995

By D. Su

This paper presents the details and results of a preliminary investigation into the response of borehole pressure cells (BPCs) in soft coal. Two parallel approaches, laboratory calibration and nonlinear finite element simulation, were adopted for deter- mining the BPC K-factor, which was defined as the ratio of cell pressure change to the corresponding change in external pressure. Results from both the laboratory calibration and the nonlinear finite element simulation revealed a nonlinear response of cell internal fluid pressure to external loading. The K-fact& also is shown to increase with increasing setting pressure and decreasing medium modulus. -Depending on the setting pressure, the K-factor for coal having a Young's modulus of 1.6 x lo5 psi ranges from nearly 1.2 at 2,000 psi of external pressure to 1.485 at 8,400 psi of external pressure. The improved under- standing of BPC behavior leads to the more accurate calculation of BPC K-factor in coal which significantly improves the correlation between pillar pressures measured in underground coal mines and those predicted by nonlinear finite element simulations of these pillars.

Jan 1, 1990

By H Phillips, A Spaeth, B Belle

There are several well-known, extensively researched and tested methods of suppressing a coalmine methane and coal dust explosion. The choice of method used is dependent on the legislative requirements of each country, which in turn are influenced by mining conditions in that jurisdiction. For example, seam gas content and the dustiness of the coal will combine to create the hazard, while the physical and chemical properties of the seam might influence the possibility of ignition sources such as frictional ignitions. The mining method and layout will also influence the choice of preventative or proactive suppression devices. The decision as to which method is approved and adopted should be based on currently tested and available technology and the latest research outcomes, and should be subjected to a rigorous risk assessment, since a methane explosion propagating into a coal dust explosion cannot be countenanced.Every new technology must undergo stringent tests and these tests must be certified by accredited research facilities or laboratories. Upon approval, an explosion suppression system or the critical components of such a system should be tested in a more realistic environment. This environment can ideally be found in an operating underground mining section for evaluation purposes. Based on the insight gathered in such an environment, a realistic evaluation of the effectiveness of a potential system can be carried out. The explosion suppression system described in this paper has been tested on numerous occasions at accredited test facilities. The technology described in this paper has been used in various applications in underground coalmines and has been adapted to fulfil and exceed the requirements set out for methods currently in use. This paper describes the underground evaluation results of the latest technology in active suppression systems as used on continuous miners was adopted to perform as a roadway explosion barrier.CITATION:Spaeth, A, Belle, B and Phillips, H, 2017. Underground bulk sampling, uniform conditioning and conditional simulation – unrealistic expectations?, in Proceedings Australian Mine Vent Conference 2017, pp 197–202 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

By None None

Life as a mining/mineral professional doesn’t leave much time for perusing 20-page technical papers. Yet, being technologically savvy is part and parcel of a successful career in this industry. What’s an intelligent, well-informed person to do?

Mr G H Park was born and brought up in Zimbabwe, in mining from the University of the Witwatersrand. Starting as a Learner Official at Rand Mines, he went Mr D J van Niekerk was educated at Helpmekaar Boys' High School in Johannesburg and the University of Pretoria. Mr C J C Janse van Vuuren was educated at Klerksdorp High School, Pretoria Technical Colege, the University of Pretoria, and Unisa. He holds the folowing degrees: BSc (I&S), BSc Hons (Met Pta), ND (Met Tech), AEP (Unisa). Prof. R F Sandenbergh was educated at the Afrikaanse Hoerskool Germiston and the University of Pretoria. He holds the degrees of B Ing (Chem), M Ing (Chem), and D Ing (Metal). President's Award Professor Jannie van Deventer, Head of the Department of Metalurgical Engineering at the University of Stelenbosch, has been honoured with one of the five President's Awards for 1990. These awards are made by the CSIR's Foundation for Research Development. G R Bozzoli Awards* Prof. Alan Kemp, Dean of the Faculty of Engineering at the University of the Witwatersrand, has appealed to industry not to cut bursary funding during recessionary times.

Jan 1, 1990

Mr K.R. Beard was born on 19th December, 1958. He attended Marist Brothers College, Observatory, and Marist Brothers College, Linmeyer. He was awarded a bursary by SEIFSA (Steel and Engineering Industries Federation of South Africa) and gained the degree of B.Sc. Eng. metallurgy at the University of the Witwatersrand in 1982. He is a member of the Engineers' Society of South Africa. Mr G.A. Brown was born on 27th June, 1934, and matriculated at St John's College. He obtained the degrees of RSc. Eng. (Met.) at the University of the Witwatersrand in 1957, and M. Met. at Sheffield University in 1959. He is a member of the Institution of Mining and Metallurgy (UK) and the Society of Mining Engineers (USA). Or LA. Cramer was born in the USA and, having received a B.Sc. degree in metallurgical engineering from the Colorado School of Mines, he emigrated to South Africa in 1971. He enrolled as a graduate student at the University of Natal and successfully completed both an M.Sc. and a Ph.D. degree in chemical engineering.

Jan 1, 1989

Mr D. Twigg graduated in Metallurgy at the Sheffield Polytechnic, and later obtained a Master of Science degree at the University of Bradford. Mr I.D. Matthews matriculated at Roosevelt High School and joined the No. 1 Parachute Battalion in 1968. He worked in Zimbabwe for 31 years in geological prospecting, civil engineering, and open-pit mining.

Jan 1, 1985

Mr D. Wilson was born in Vereeniging, where he also completed his schooling, matriculating from General Smuts High School in 1977. Mr K.A. van Gessel was born in 1937. His final studies were conducted at Delft University, where he graduated with an M.Sc. degree in mining engineering. Mr J.G. McCaUum was born in 1938 and matriculated at Jeppe Boys' High School, Johannesburg. Mr H. Scot RusseU started his mining career at Randfontein Estates Gold Mining Co. Witwatersrand, Limited, where he served as temporary Geological Assistant, Sampler, Surveyor, Shift Boss, and Mine Overseer. Mr A.M.P. Henderson was born in 1950, in Kiel, West Germany. Mr J.L. Nel matriculated in 1957. This was folowed by his atainment ofthe folowing degrees: B.Sc. (Chemistry, Physics) in 1961, B.Sc. Hons. (Metalurgy) in 1965, M.Sc. (Metalurgy) in 1967, and MDD (student of the year) in 1981

Jan 1, 1989

Mr G. Maude was educated at Huish's Grammar School (Taunton) and Leeds University. He graduated in 1961 with a B.Sc. degree in Mining. Mr E.B. Crocker was educated at Florida Park High School, Witwatersrand Technical College, and the University of the Witwatersrand.

Jan 1, 1985

Dr R. E. Robinson, Pr. Eng., obtained a B.sc. (Chem. Eng.) cum laude from the University of the Witwatersrand in 1950 and a Ph.D. (Eng.) from the same University in 1953, where he was awarded the Haikes Memorial Medal for Industrial Chemistry. Professor G. G. Garrett was appointed Professor of Physical and :Fabrication Metallurgy in the Department of Metallurgy at the University of the Witwatersrand in June 1980, and in January 1984 he became Head of the Department. Mr P. A. van Wielligh, Pr. Eng., climbed the mining ladder in the hard way, starting as a Mine Surveyor in 1936 and working his way up as Chief Surveyor, Underground Manager, Mine Manager, and Consulting Engineer, to Executive Director, including the intermediate steps. Mr H. E. James, Pr. Eng., is a graduate in Chemical Engineering from the University of the Witwatersrand. Both his B.sc. degree (1961) and his M.sc. degree (1964) were obtained on bursaries, the former from Gold Fields of South Africa and the latter from the Atomic Energy Board. Mr G. Pienaar, Pr. Eng., obtained a B.Eng. (Met) in 1967 and an M.Eng. in 1973, both from the University of Pretoria. Dr A. K. Haines, Pr. Eng., obtained all his degrees from the University of Natal, finishing with a. Ph.D. in 1971. Mr B. C. Alberts, Pr. Eng., obtained his academic training at the University of Pretoria, where he was awarded B.sc. degrees in both agricultural engineering (1963) and mining engineering (1965). Mr H. C. van Zyl, Pr. Eng., holds B.sc. degrees in mining engineering (1968) and civil engineering (1972), both from the University of Pretoria.

Jan 1, 1984

Professor R.P. King holds a Ph.D. degree in chemical engineering, which he obtained at the University of Manchester in 1963. After that he lectured in the Departments of Chemical Engineering at the Universities of the Witwatersrand and Natal. From 1968 to 1973, he was Leader of the Chemical Engineering Research Group of the National Institute for Metallurgy at the latter University. Mr C.E. Fivaz, Pr. Eng., is Chief Consulting Metallurgist of Rand Mines (Mining & Services) Limited, and is responsible for the metallurgical activities of the Gold and Uranium Division and the Coal and Base Minerals Division of the Group.

Jan 1, 1984

Introducing your Council. Mr J. S. Freer, Pr. Eng., after matriculating at Michaelhouse in 1944, obtained a B.8c. degree in chemistry and biology (1948) and a B.Sc. (Hons.) in chemistry (1949) from the University of the Witwatersrand. Mr G. C. Thompson matriculated at Dale College in 1951. He then attended the University of the Witwatersrand, where he obtained a B.8c. (Min. Eng.) in 1959. Mr P. T. Fewell was born and educated in the United Kingdom. After obtaining the degree of Bachelor of Engineering (Mining) in 1958 at Sheffield University, he emigrated to South Africa. DtP. R. Jochens, Pr. Eng., has been a member of Council since 1974, serving as President in 1980-1981.

Jan 1, 1984

Professor N. S. Budavari holds a Dip!. Min. Eng. from the Technical University of Sopr on, Hungary, and a Ph.D. degree from the University of Newcastle-upon-Tyne, U.K. Mr J. J. Geldenhuys, Pr. Eng., is Divisional Manager Mining of Anglovaal Limited, being in charge of Prieska Copper Mines (Pty) Limited, Loraine Gold Mines, Limited, and Village Main Reef Gold Mining Company Limited.

Jan 1, 1983

Humankind's interest in measurement of human physical strength probably dates to the first humans. At that time, life was truly a struggle in which the fittest survived. To a great extent, fittest meant strongest. Interestingly, current interest in human physical strength in the workplace stems from 1970-1980s vintage research demonstrating that persons with adequate physical strength are less likely to be injured on physically demanding jobs. Survival in many modem workplaces may still be a case of survival of the strongest. There is, however, a flip side to this issue - that persons with limited strength are more likely to be injured on "hard" jobs. To address this problem, we can apply what we know about physical strength to job design. "Hard" jobs can be redesigned to be within the physical strength capability of most people. Since physical strength is important to these jobs, we must find ways to quantify it through testing. This publication concerns human physical strength testing. Its purpose is not to recommend any particular type of testing, but rather to describe the types of testing available and their uses. It is up to each individual user of strength testing to decide which testing technique is most appropriate for his or her particular application. This booklet discusses four types of strength testing: isometric, isoinertial, psychophysical, and isokinetic. Human Strength Before describing the different types of strength measurement, we must define the term "strength" and explain the concept of strength measurement. Strength is defined as the capacity to produce force or torque with voluntary muscle contraction. Maximum strength is defined as the capacity to produce force or torque with a maximum voluntary muscle contraction.(1,2) These definitions include some key words that must be explained. A voluntary muscle contraction is "voluntary." When a person's physical strength is measured, only the effort the person willingly puts forth at the time is measured. Thus, when we test a person's "maximum strength," we are not measuring his or her actual maximum, but some lesser value representing what he or she is comfortable expressing at the time with the existing equipment and environmental conditions. Interestingly, when researchers startled persons being tested (e.g., by setting off a starter's pistol behind them), they have found significant increases in measured strength.(3) It has been hypothesized that the lower strength displayed during normal testing provides a margin of safety against overloading and damaging muscle tissue. The test equipment and the tested person's familiarity with the process also influence the "voluntary" strength output. The interface between the tested person and the test equipment is particularly important. A poorly designed interface induces localized tissue pressures that vary from uncomfortable to painful. In this situation, testers are measuring voluntary discomfort tolerance - not strength. It is important for strength researchers to keep the "voluntary" nature of their data in mind when they are designing their equipment and protocols.

Jan 1, 1998