Search Documents

By E. Topuz, C. Patrick

Longwall face-to-face transfers can cost more than $100 per minute in lost production potential and $100,000 for personnel and supplies. Such high costs make extensive planning and control of the transfer process a critical necessity for the economic feasibility of longwall operations. Operations research techniques are used for the analysis and modeling of longwall face-to-face transfers. Transfer data has been collected from companies who operate, over 35%, of the total US longwall faces. Comprehensive sequence networks of existing longwall transfers were developed; simulation was used to generate models of transfers under Carving conditions; and the economic feasibility of tine-cost tradeoffs in the transfer procedure was investigated.

Jan 1, 1994

By Douglas E. Pollock

Recent NIOSH published information has shown an increase of rapidly progressive coal workers? pneumoconiosis (CWP) in the southern Appalachian coal region (SAR) of the U.S., despite the fact that compliance data indicates that most coal miners have been exposed to coal mine dust concentrations below the statutory limit of 2 mg/m³. While the exact cause of these elevated CWP levels in the SAR has not been established, several factors may be contributing to the increase in occupational lung disease among coal miners. The mining of high rank coal is known to lead to higher CWP rates, and this type of coal is mined in a portion of this region. Also, a high percentage of the mines in the region are on reduced dust standards because of the high silica content of the airborne dust resulting in miners possibly being exposed to excessive amounts of respirable silica dust. Exposure to excessive amounts of respirable silica dust can lead to silicosis, a disabling and potentially fatal lung disease. NIOSH?s Respiratory Hazards Control Branch has been investigating the possible causes that would account for the observed higher trends in disease progression through literature review, data analysis and in-mine surveying. The investigation to date has revealed that underground mines are faced with cutting large amounts of rock in order to maintain haulage clearances. Cutting rock not only increases the potential for silica exposure, it increases the requirement for machine maintenance, which was a concern observed during dust surveys conducted by NIOSH. Over half of the mines operating in the SAR are on reduced standards due to high silica content. Adequate face ventilation of the continuous miner and roof bolter and limited down-wind operations from the miner are also issues of concern and items that require the constant attention of miners operating in these conditions.

Jan 2, 2010

By D. E. Pollock

Recent NIOSH published information has shown an increase of rapidly progressive coal workers? pneumoconiosis (CWP) in the southern Appalachian coal region (SAR) of the U.S., despite the fact that compliance data indicates that most coal miners have been exposed to coal mine dust concentrations below the statutory limit of 2.0 mg/m³. While the exact cause of these elevated CWP levels in the SAR has not been established, several factors may be contributing to the increase in occupational lung disease among coal miners. The mining of high rank coal is known to lead to higher CWP rates, and this type of coal is mined in a portion of this region. Also, a high percentage of the mines in the region are on reduced dust standards because of the high silica content of the airborne dust resulting in miners possibly being exposed to excessive amounts of respirable silica dust. Exposure to excessive amounts of respirable silica dust can lead to silicosis, a disabling and potentially fatal lung disease. NIOSH's Respiratory Hazards Control Branch has been investigating the possible causes that would account for the observed higher trends in disease progression through literature review, data analysis, and in-mine surveying. The investigation to date has revealed that underground mines are faced with cutting large amounts of rock in order to maintain haulage clearances. Cutting rock not only increases the potential for silica exposure, it increases the requirement for machine maintenance which was a concern observed during dust surveys conducted by NIOSH. Over half of the mines operating in the SAR are on reduced standards due to high silica content. Adequate face ventilation of the continuous miner and roof bolter and limited down-wind operations from the miner are also issues of concern and items which require the constant attention of miners operating in these conditions. Disclaimer: Mention of any company or product does not constitute endorsement by the National Institute for Occupational Safety and Health.

Jan 1, 2009

The influence of varying amounts of magnesia, silica, and alumina in iron ore sinter on its mineralogy, reducibility index (RI), reduction disintegration index (RDI), physical breakdown (AI and TI), and production properties (coke breeze rate) were examined. It was found that the mineralogy of iron sinter can more easily be predicted from its chemical composition than from the RI, RDI, AI or TI. Anticipating the consequence that varying amounts of MgO and SiO2would have on sinter properties is complex, and not necessarily predictable. High concentrations of Al2O3in the sinter result in high concentrations of the SFCA phase, but with drastically deteriorated properties. This study also confirmed that the form in which fluxes are added to the raw material sinter mixture affects the mineralogy and properties of the produced sinter.

Jan 1, 2010

By T. Holmes, D. C. Russell, G. Jolly

"The AMEC Oakville office is involved in the design and construction of an iron ore concentrator located in Liberia. Currently, the site ships Direct Shipped Ore (DSO) to overseas customers. The DSO mine-site and port can experience heavy annual rainfalls. The IMSBC Code requires that cargoes are only accepted for loading when the moisture content of the cargo is less than its Transportable Moisture Limit (TML). The moisture content of the DSO has, on occasions, risen to near or above its TML. AMEC was asked to advise whether the concentrate produced from the new concentrator would or would not have the same problems with moisture content and ship loading as the DSO.INTRODUCTION Liberia was, at one time, the world’s sixth largest exporter of iron ore and used some of the most modern mining operations of their time. However, the country has not produced iron ore over the past seventeen years because of civil unrest. The return of stability to the country has allowed the redevelopment of the iron ore industry. ArcelorMittal Liberia (AML) obtained a concession for mining in the Nimba County area of Liberia (Figure 1) in December, 2004 and has studied the known iron ore deposits and former mining operations in this area. It began phase 1 operations in June 2011 with the direct shipping of high grade ore at a rate of up to 4Mtpa. The processing of the lower grade ore in phase 2 of the project requires additional processing capability to produce at the design rate of 15Mtpa. DSO and Concentrate The DSO in the first phase is selectively mined at an average grade of 60% Fe, and then crushed and screened to -10 mm with no washing or concentration. Testing of samples has indicated a size distribution that is finer than typical sinter feed material, although critical material below 0.10 mm is low in most cases, and overall the ore is coarser than typical concentrates or ultrafine products (Feasibility study report, 2011). The phase 1 DSO facility will cease operation after the phase 2 concentrator comes into operation."

Jan 1, 2014

By Charles Deacon

The mining industry is constantly taking greater cognisance of their operating costs as a strategy to counter the effects of falling commodity prices. As a result, optimal operating efficiency is more important than ever. One such operation is that of blasting. Considering the relative increasing costs of explosives and accessories it is desirable to optimise the number of blast-holes fired by maximising their individual output. This achievement may now only be possible following the advent of higher technologies in the form of modified explosives and electronic detonators. This paper reviews and introduces some techniques of blast monitoring, types of operations where each is most suited, resulting modifications to blast designs, and identifies some pitfalls to watch out for when analysing the results.

Jan 1, 2000

By Zhigang Liang

Investigation into the mixing of 150t ladle furnace by two-nozzle jetting was performed by a water model simulation of 1:4. The effects of nozzle arrangements including separation angle, radial position and asymmetry as well as tracer adding position on the mixing time were studied. The most favorable mixing is achieved when the two nozzles are symmetrically arranged at half radii in the ladle, with 45o separation angle. The empirical relationship between the mixing time and stirring power intensity has been established for two-nozzle jetting based on the present experimental results. In addition, the swelling above bath surface is also investigated with two-nozzle jetting.

Jan 1, 2009

By R. B. Krog

The use of belt air as an intake source at longwall operations has greatly changed over the past decades. The practical considerations for the use of belt air are controlled by a variety of factors including airflow quantity and velocity, coal methane content, methane desorption rates, coal mining rate, belt length, stopping leakage, and the number of gateroad entries. At longwall operations, the advantages and disadvantages of belt air are different for gateroad development and longwall panel extraction. During gateroad development, the use of belt air to ventilate the working section will reduce the leakage from the intake to the belt compared to the belt air being ventilated outby the working sections because of lower pressure differentials. A greater quantity of airflow will reach the last open crosscut with belt on intake than outby, given the same amount of pressure and airflow available at the mouth of the section. This paper will investigate the current ventilation practices regarding the use of belt air during gateroad development and longwall panel extraction. Operating considerations regarding air quantities and pressures to deliver the required airflow will be investigated using ventilation network modeling.

Jan 1, 2009

By Yunsheng Yao, P. Golledge, A. D. S. Gillies

In order to investigate the explosibility of sulphide mineral dusts, sulphide ore samples were collected from five underground metalliferous mines in Australia. The mineralogical and chemical composition of the dust samples was analysed by X-Ray Powder Diffraction and Atomic Absorption techniques. Simulated post detonation fumes were produced and used in dust explosibility tests to examine the influence of the fumes on sulphide dust ex- plosions. These tests were conducted in a 20 Litre Siwek Explosion Chamber with measurement and control system that is regarded as a standard testing system worldwide for dust explosion studies. The dust mineralogical composition and dust explosibility tests indicated that the content of sulphur can not accurately predict the explosibity of the sulphide dust. The percentage content of pyrite in the sulphide dust can be a relatively reliable diagnostic criterion in evaluating the risk of sulphide dust explosions in the mining of a massive sulphide orebody. The hybrid explosion tests demonstrated that the post detonation fumes from ANFO not only decrease the lower explosion limit of the sulphide dusts, but also increase the severity of the dust explosions. The explosion pressure reaches its peak value when the fumes content in the explosion chamber is about 20 per cent by volume

Jan 1, 1997

By Chi-Mun Song, Seok-Hyun Choi, Seok-In Hong, Han-Kee Jang

Accurate measurement and evaluation of hand-transmitted vibration from a power tool is an important issue for tool manufacturers, because they are obliged to develop low-hazard power tools for workers. The International Standard ISO 5349(1) dictates a systematic procedure for the measurement and evaluation of hand-transmitted vibration. However, the uncertainty in this measurement is too large for manufacturers to apply such data to the design and modification of power tools. There can be several sources of this uncertainty in such measurements; e.g., operator-dependent, power tool-dependent, and operational conditions (see Table 1). For a manufacturer to characterize the exposure of a power tool’s use to a given level of vibration, the relationship between these uncertainty factors and the measured vibration must be elucidated. In this study, we investigated the effect of several factors on the uncertainty in measurements. [ ] Methods In this study, some of the factors in Table 1 were selected for examination, and their effect on the measured variation was quantitatively investigated. Three tools from the same manufacturer were sampled at random in our experiments, and each of five of the same type of insert (disks or tips) was installed into each tool. Although each of the tools and inserts were of the same design and were made by the same production process, they differed from one to another, which can be a source of the variation in the measured vibration. Three human subjects participated in our experiments, which were carried out as stated in ISO 5349. The subjects were asked to maintain their posture, and the applied force was kept as constant as possible. The applied force was monitored using an indirect method, where vibration energy was displayed in real time during the experiment using a three-axis accelerometer attached to the work piece at a specified point. The appropriate range of the applied force was predetermined to cover the range of real work operations. The engineering tolerance between the inner diameter of a grit disk and the outer diameter of the tool shaft leads to an eccentricity of the mass at the center of the disk. The degree of eccentricity varies with installation, and this is another source of uncertainty. In our study, the effect of this eccentricity was investigated by carrying out repeated assembly and disassembly of an insert.

Jan 6, 2006

By O. Dojcar

The results of a laboratory investigation of rock fragmentation conducted with a model material were partially verified under field conditions. The object of the investigation was to study the qualitative and quantitative relations between the parameters of the primary blast and fragmentation to enable the planning of an economically efficient degree of disintegration with optimum utilisation of the blast energy. The three blast parameters that were considered were burden, specific charge and the ratio of spacing to burden

Jan 1, 1991

By N. Coli

The exhausted Santa Barbara open pit mine (Tuscany, Italy), owned by the main electric power company in Italy (ENEL S.p.A,) extracted lignite as a fuel for the Santa Barbara thermoelectric power plant. The mining activity led to the excavation of a wide slope (with maximum height of 200 m and a planar extension of about 1300 m x 500 m) in the Shale Limestone Chaotic Complex (SLCC) (Figure 1). Since the beginning of its excavation the slope underwent rotational landslides and diffuse instability phenomena. From a geotechnical point of view the SLCC represents a typical bimrock (block-in-matrix rock) (Medley 1994, Medley 2002, Medley 2007) characterized by a mixture of a highly sheared, scaly-fabric, clayey matrix and calcareous blocks ranging from a few millimetres to tens of metres in size. Since the geometrical properties of blocks (grain-size distribution, shape, orientation and volumetric proportion) have been proved to influence the mechanical behaviour of bimrocks (Lindquist & Goodman 1994, Goodman & Ahlgren 2000, Kim et al. 2004, Sonmez et al. 2006), the aim of the present study is to investigate the geometrical properties of calcareous blocks in order to properly characterize the mechanical behaviour of the SLCC bimrock and to further assess the stability of the slope. Block size-distribution and shape were investigated by means of advanced image analysis techniques of SLCC pictures taken in the field. Geostatistical semivariograms and variographic maps were also used in order to investigate the anisotropy of block spatial distribution. Finally, in-situ large sized sieving tests were carried out to investigate the volumetric block proportion within the clayey matrix.

May 1, 2009

By Simon Lekakh, Von Richards, C. Hank Rawlins, Kent Peaslee

"Batch aqueous leaching and carbonation tests were conducted using industrial steelmaking slags to determine the effect of carbonic anhydrase enzyme as a catalyst. Calcium leaching is a strong function of particle surface area, and the extent can be expressed as a function of time and particle size. Carbonic anhydrase did not affect the calcium-leaching rate, however, it did catalyze calcium carbonate formation to achieve a neutralization time near the theoretical rate. Additionally, carbonic anhydrase modified the precipitate morphology due to accelerated particle nucleation. Time controlled tests in which the pH dropped to ~6 decreased the amount of carbonate produced, and this effect was exaggerated by carbonic anhydrase, while pH controlled tests (>8.5) exhibited the highest rate of carbonation. Because the leaching rate was ~50% faster than the carbonation rate, a further increase in the amount of carbonation may be realized by using carbonic anhydrase however pH must be >10.3.IntroductionSteelmaking slag contains high fractions of alkaline earth oxide based phases (i.e., CaO and MgO) that exothermically form carbonates. Thus, it is being considered as a means of permanent carbon dioxide sequestration. At current U.S. steel production rates, approximately 13-17 million tons/year of slag are generated from basic oxygen furnace (BOF), electric arc furnace (EAF), and ladle metallurgy furnace (LMF) processes [1]. BOF and EAF slag is used as high quality mineral aggregate or cement clinker, while LMF slag, produced at ~15% the rate of BOF and EAF slags, has limited use as blast furnace flux or acid mine neutralization with the majority going to landfill [2]. Based on slag’s chemical nature and immediate availability as a co-product from steel production, the steel industry initiated a project to investigate hydrous carbonate formation in steelmaking slag as a method of sequestering carbon dioxide emitted in steelmaking offgas [3]. The goal of this project is to determine the reactor parameters suitable for the design of an industrial system for treating steelmaking offgas with raw or minimally processed slag."

Jan 1, 2009

By İbrahim Çınar, Hakan Özşen

Mine workers in heavy and dangerous work are under several physical risk factors, for example temperature, humidity, noise, vibration, lighting and air velocity. Thermal comfort includes parameters such as air temperature, air humidity, air flow rate, radiant heat, metabolic rate and garment insulation. In this study, thermal comfort conditions were evaluated using thermal comfort indices defined as predicted mean vote (PMV) and predicted percentage dissatisfied (PPD) which were determined by measurements taken from an underground coal mine for approximately 100 days. Although the metabolic rate (light work) was kept at 2 met, it was found that predicted mean vote ranged between − 2.58 and 1.68. The predicted percentage dissatisfied index was found to reach 95%. According to the results, it can be seen that thermal comfort may have negative effects on occupational health and safety. The change in thermal comfort index values in the Soma Underground Coal Mine was investigated in detail and the reasons for the changes were determined. Furthermore, determining the optimal working environment for the mine workers was also an aim of this study.

By Steven J. Knoll, Theodore J. Williams, Douglas F. Scott

Highly stressed rock in stopes continues to be a primary safety risk for miners in underground mines because it can result in failures of ground that lead to both injuries and death. Spokane Research Laboratory personnel investigated electromagnetic (EM) emissions in a deep underground mine in an effort to determine if these emissions could be used as indicators of impending catastrophic ground failure. Results suggest that (1) there is no increase in the number of EM emissions prior to recorded seismic activity, (2) some EM signals are generated during blasting, (3) interference from mine electrical sources mask seismic-generated EM signals, (4) EM emissions do not give enough warning (compared to seismic monitoring) to permit miners to leave a stope, (5) the distance an EM signal can travel in the rock is between 18 and 40 m, and (6) current data acquisition systems do not differentiate between EM signals generated from seismic activity and random mine electrical noise. These results preclude monitoring EM emissions as precursors of impending catastrophic ground failure.

By A. Juganda, F. WILSON, H. PINHEIRO, N. SANDOVAL, J. F. Brune, G. E. Bogin Jr.

To evaluate methane explosion hazards in longwall coal mines, a CFD model was developed along with a 1/40th-scale, optically accessible model of an underground longwall coal mining section. In this project, CFD models assisted in the design of the physical model to ensure specifications were met for accurately representing the scaling physics as well as to assist in narrowing the experimental matrix and identifying key locations for sensor placement to measure velocity, pressure, and gas concentrations. This research will help develop strategies for methane monitoring that prevent methane ignitions and explosions in longwall coal operations.

Aug 15, 2022

By A. Juganda, F. WILSON, G.E. BOGIN, H. PINHEIRO, N. SANDOVAL, J.F. BRUNE

To evaluate methane explosion hazards in underground longwall coal mines, researchers at the Colorado School of Mines developed a computational fluid dynamics (CFD) model along with a 1/40th-scale, optically accessible, physical model of a longwall mining section. In this project, CFD models assisted in the design of the physical model to ensure specifications were met to accurately represent the scaling physics as well as to assist in narrowing the experimental matrix and identifying key locations for sensor placement to measure velocity, pressure and gas concentrations. This research will help develop strategies for methane monitoring to prevent methane ignitions and explosions in longwall coal operations.

Dec 1, 2022

By Wendy M. Brunner

A 70% excess of mesothelioma, an asbestos-related cancer, has been reported among men in northeastern Minnesota, where iron mining has been the major industry. The Minnesota Department of Health has studied iron miners who developed mesothelioma to identify possible sources of asbestos exposure. A database of all Minnesota residents diagnosed with mesothelioma between 1988 and 1996 was linked to a database of approximately 72,000 current and former Minnesota iron-mining employees to identify cases who had ever worked in the mining industry. The job histories of the cases were examined to determine if any of their jobs could have involved exposure to commercial asbestos. Seventeen individuals diagnosed with mesothelioma in Minnesota between 1988 and 1996 were found to have worked in the iron mining industry. Of the 15 for whom adequate work histories were available, 14 had identifiable sources of exposure to commercial asbestos in jobs held both inside and outside of the mining industry. The time between employment in these asbestosexposed occupations and the diagnosis of mesothelioma is consistent with the 20 or more year latency period that has been observed in other studies of this cancer. © 2007 Elsevier Inc. All rights reserved. Keywords: Mesothelioma; Asbestos; Iron miners; Taconite; Epidemiology; Case series

Jan 1, 2007

By S-J. Park

When evaluating mining investment opportunities, one should consider the risks associated with mineral exploration and development. These are commonly classified as technical, economic, and political risks, and are accounted for in the investment decision by changing the discount rate. Thus, a company may use different discount rates associated with varying risks in order to compensate for the variability of success. The discount rate has a tremendous effect on the economic evaluation of mineral projects. Even when all other factors used as inputs for calculating the NPV (net present value) are equal, the project under consideration may be accepted or rejected depending upon the discount rate. Determining a realistic discount rate for a given project is therefore the most difficult and important aspect of cash flow analysis. It should be determined with the consideration of proper technical, economic, and political conditions surrounding the specific project undergoing economic evaluation. One key problem for determining the appropriate discount rate is that it typically depends more on subjective perception of the degree of risk or other experience factors than on a systematic approach. Thus, this study aims to identify, analyse, and document the type, role, and impact of risk factors influencing the determination of discount rates, and then to determine discount rate by using the aforementioned factors.

Jan 1, 2011

By David Oyler, Craig Compton

The The National Institute for Occupational Safety and Health (NIOSH) Pittsburgh Research Laboratory (PRL) is continuing to investigate the behavior of fully grouted roof bolts in the weak roof rock of the Safety Research Coal Mine (SRCM). This paper describes the results of three studies: • A series of 24 pull tests of bolts installed fully grouted and overcored to leave 12 inches of grouted bolt. The tests compared the pull-out performance of offset-head roof bolts with that of standard 5/8-inch bolts; • A second series of 24 tests that compared the pull-out loads obtained by bolts installed with 1 ft of resin (a Short Encapsulation Pull Test or SEPT) to that of fully grouted bolts overcored to leave only 12 inches of grouted bolt, and; • An investigation into the pressures generated during the installation of fully grouted resin bolts. All of the bolts installed and pulled were overcored and removed from the roof after the pull tests to allow inspection of the resin. The first study found that there was no significant difference in pullout load between the offset-head bolts and the standard bolts. The second study, comparing the SEPT bolts and the partially-overcored fully grouted bolts, indicated that SEPT can significantly underestimate bolt anchorage grip factor, suggesting that the SEPT is a conservative measure of actual bolt performance. Significant loss of resin to cracks in the roof was observed in the bolts overcored in the SRCM. The third study explored one possible explanation for the resin loss, high pressures generated during bolt installation. These tests employed bolts installed in strain gauged steel tubes. The results confirmed that significant pressures (greater than 4,000 psi) can be generated during bolt installation. The results of the pressure tests, combined with the observations of resin loss in bolts installed in the SRCM, suggest that under some circumstances resin loss and under-encapsulation could take place and lead to degraded bolt performance. Glove fingering was observed in all recovered bolts to various degrees. The limited comparative data suggested that the effect of glove fingering ranged from slight to moderate. Complete mixing of the resin was observed on all of the 40 bolts recovered (28 fully grouted and 12 SEPT). Australian and U.S. resins were compared and the Australian resins were observed to have much smaller catalyst compartment areas and lower resin viscosities. These differences are suggested as potential explanations for occasional resin mixing problems noted in Australian resin bolt installations.