Search Documents

By M. Schmidt, P. Nord, M. Larinkari

Cathode stripping machine technology has been developed significantly both in electrorefining (ER) and electrowinning (EW) applications in the last ten years. The main driver has been robotic cathode handling, which has enabled increased flexibility to meet different layout and material handling requirements for both ER and EW processes. Additionally, cathode stripping stations have been continuously developed to optimize speed and to reduce mechanical stress of permanent cathodes. 'taco' type cathodes have been proven as beneficial approach for high capacity operations (particularly in Cu ER), where over 600 cathodes per hour continuous throughput has been achieved. However, the latest developments also apply to split type cathode stripping. Besides material handling, the modern cathode stripping machine has also an important role to provide information for production and quality monitoring. This paper describes the latest developments from the field of copper cathode stripping based on several different projects implemented in the recent years. INTRODUCTION After introduction of the permanent cathode technology in the late 1970s, it became the prevailing technology in copper refineries over the traditional starting sheet process by the end of 1980s. The main driver was less labour-intensive production due to fewer processing steps required along with more automated electrode handling equipment (cathode stripping machine, anode preparation machine, anode scrap washing machine and tankhouse cranes). Since then the design of the cathode stripping machine has followed the development of permanent cathode technology. The main development steps so far can be summarized as follows: Full Deposit Stripping Machine (FDSM) based on waxed permanent cathodes or cathodes with bottom edge strips resulting in split cathodes (copper sheets separated, see Figure 1) Wax less cathode stripping based on V-groove on bottom of the edge strip resulting in either ‘taco’ cathodes (enveloped copper sheets, see Figure 1) or split cathodes Full Deposit Robotic Stripping Machines (FDRSM) using 1–5 robots for permanent cathode handling and cathode stacking.

Jan 1, 2019

By Yasushi Ishikawa

The fact that the degree of granulation and the state of granulated particles of sinter raw mixtures are the influential factors in ensuring coke combustibility and permeability during sintering has been clarified. Based on this knowledge, Nippon Steel developed the divided coke-addition process and the technology to utilize binder, and applied them on a commercial scale. Productivity and sinter quality are thereby greatly improved with a significant reduction in fuel consumption.

Jan 1, 1977

Although cyclones have been around in their current form since the early-1890s, there have been some exciting new developments, which have extended their efficiency/operation. These developments have taken place with both dense medium and classification cyclones. The more noteworthy developments are:Inlet designInlet design is the determining factor in classification cyclone capacity and efficiency. The recently developed ribbon inlet with patented pressure bulge has not only resulted in unbelievable increases in capacity, but also in efficiency. Sharpness of separation corresponding to an alpha value of greater than four has been achieved! Secondary offtakeOne of the factors leading to reduced cyclone efficiency is the presence of coarse particles in the cyclone overflow. The secondary offtake has been developed specifically to scavenge these particles from the cyclone overflow with great success. Water injectorThe other major factor resulting in reduced cyclone efficiency is the presence of misplaced fine particles in the cyclone underflow. The water injector, which has been around for many years in various forms, can reduce this short circuit fraction by up to 50 per cent. 3-in-1 cycloneThe 3-in-1 cyclone combines the inlet design, secondary off take and water injector into a single unit resulting in the most efficient classification cyclone available in the market. The RejectorTMIron ore has a high yield to underflow and traditional dense medium cyclones have always been spigot constrained. The Rejector TM is an exciting new development whereby the spigot capacity has been increased substantially. The application of the Rejector TM will result in fewer/smaller cyclones being required for a given duty resulting in efficiency gains and reductions in both operating and maintenance costs.

Jan 1, 2002

By Henk van der Bijl, Sean Rogers, Eugene Sidorski, Alan Carpenter

The electrode column is the heart of the submerged arc furnace. Superior electrode performance provides improved furnace performance. This paper describes the main features of the electrode column that delivers superior performance in furnaces worldwide, developed by Pyromet. Pyromet?s electrode comprises the compact slipping device, lower electrode assembly, upper and lower mantles, self-adjusting electrode seal, paste heaters, and Pyromet?s patented innovative electrode breakage detection and length determination system. Pyromet?s slipping device features compact interlocking clamping rings, incorporating fail-safe spring-loaded design. The interlocked clamping rings distribute the clamping force over a larger area of the electrode casing, preventing damage. The slipping device assembly features a low maintenance modular design that allows rapid slipping cycle times, back slipping, and compatibility with Pyromet?s electrode breakage detection and length determination system. Pyromet?s lower electrode assembly consists of the contact shoes, pressure bellows, pressure ring and heat shields. The contact shoes and pressure ring are designed for long, trouble free operation whilst the pressure bellow configuration equalise contact pressure and current distribution. Furthermore, the contact shoes incorporate a self cleaning feature, ensuring optimum electrical contact. The segmented design offers easy maintenance. Pyromet?s clients experience less down time due to longer component life. Pyromet?s remote adjusted electrode seal assembly reduces the rope seal working temperature, increasing rope life. The self compensating rope seal clamping force ensures an effective seal as the rope wears. Pyromet?s electrode breakage detection and length determination system detects electrode breaks utilising Pyromet?s electrode holder and data processing system. The length measurement system controls electrode length, eliminating the occurrence of short electrodes. The length measurement system furthermore eliminates the need for manual electrode length measurement, reducing associated production losses during furnace burn downs.

Jan 1, 2007

By Don A. Toth

Until recently, the fire protection systems used to protect mining equipment were based on generically designed, off the- shelf concepts. These systems were reliant on single agent approaches and were generally comprised of a series of small twenty or thirty pound chemical canisters that would discharge their contents when triggered by thermal detection means. As the equipment grew in capacity, the logic used to increase the protection was to add more chemical canisters to the system. Hydraulic excavators and large-scale mining trucks grew dramatically in size into the 1990?s and beyond; with this growth came the increase in major losses due to fire. This was evidenced throughout this period, and continues to be of great concern today. During this presentation you will learn of the significant changes that have come about as a result of this history. Today, dual-agent products, infrared detection and unit-specific, engineered systems are the primary phrases used when discussing how to best protect this equipment from fire loss. This session is a must for anybody looking to optimally protect their equipment assets and for those looking to renew and/or secure new insurance for high value equipment in the future.

Apr 1, 2005

By William R. Yernberg

The 2006 North American Tunneling (NAT) Conference was held June 10-15, 2006, in Chicago, IL. The biennial conference was the first NAT conference by the newly formed Underground Construction Association of SME (UCA of SME). The UCA of SME was formed earlier this year at the request of members of the American Underground Association (AUA) (ME, April 2006, page 75). The conference included a keynote session, technical programs, workshops, a trade show and social activities. The conference exceeded expectations with 570 attendees. They included engineers, equipment manufacturers, representatives from government agencies and other interested individuals in the underground construction industry. The trade show was also a success with more than 86 booth spaces sold. Vendors included the biggest names in the underground construction and tunneling industry and included equipment manufactures, construction contractors and engineering companies. The trade exhibition provided a forum for interested parties in the tunneling industry to meet and discuss services, equipment and techniques.

Jan 1, 2006

By O. G. Lellep

IN every country economic circumstances prescribe the method used to produce a commodity at lowest cost. In Pennsylvania a man's wages for working 4 hr buys a ton of coal wholesale; in Germany a laborer must work 40 hr, or ten times as long. In western Europe, therefore, conservation of fuel is of primary importance, and recent practices of burning lime and cement differ from those employed in the United States. This paper presents data collected during a trip through western Europe in 1953. Considered uneconomical, shaft kilns for burning cement disappeared in the United States two generations ago. But because required capital investment is low and operation greatly improved, shaft kilns are still used to some extent in Europe, where fuel costs are high, and are even included in designs for plants under construction. During the last 50 years shaft kilns have been maintained at the same physical size, while their output has been increased at least four times.

Jan 7, 1954

Optical sensors have emerged during the telecom boom in the late 1900s, due to the availability to low-cost telecom-grade optical components. It's only after the telecom industry's fall in 2004 that optical sensors became sufficiently developed to be a viable technology for real-world applications. Geotechnical applications have long relied on electrical sensors such as thermocouples, strain, and the venerable vibrating wire to measure physical phenomena. Although these are well suited for a large variety of applications, electrical sensors cannot be used for all applications: these are vulnerable to noise, hazardous voltages and corrosion, limiting the environments in which they can be used. In addition, electrical wires can also become an issue when sensors require external excitation or are distant from the measurement system. Finally, changes in physical properties of electrical sensors and systems over time makes regular calibration a necessity - not easy to do when these are permanently mounted on structures. Optical sensing systems are non-conducting and use light to perform various measurements. There are several optical sensor technologies available, each with different strengths and weaknesses. In addition, there are different methods of interrogating optical sensors, each of which also present different strengths and weaknesses. To make matters worse, configuring the interrogation and scaling to physical units can also be challenging to the unprepared engineer. This paper will present a holistic view of optical sensing, presenting the different optical sensor technologies and interrogation techniques. Sample optical sensing systems will be revealed and top considerations for optical sensing will be presented.

Nov 25, 2010

By Orlando Martino

This regional report covers the mineral industries of Canada and 40 countries and areas in Latin America and the Caribbean Basin. Also included is a brief description of the mineral potential of Antarctica. The Latin American region encompasses an area twice that of the United States. Latin America and Canada have a rich and diversified endowment of mineral fuels, metals, and industrial minerals. Tables 2 and 3 provide a summary view of the importance of Latin America and Canada's output of its major mineral commodities in world mineral supply in 1989 and 1990.

Jan 1, 1993

By Barry Olson

The Peñasquito deposit in Mexico is one of the largest grassroots precious metal discoveries to be developed in recent years. Goldcorp Inc. acquired the gold-silver-lead-zinc property with the acquisition of Glamis in 2006. The company has since committed US$1.5 billion to construct the mine, mill and associated facilities. The first of two 50-kt/d (55,000-stpd) mill and flotation lines is currently being commissioned while engineering and construction continues on the second line. A high-pressure grinding roll (HPGR) will ultimately take total throughput to 130 kt/d (142,000 stpd). The Peñasquito property is located in the northeast corner of Zacatecas state, Mexico. The elevation of the property averages 1,900 m (6,200 ft) above sea level and it is situated in a wide east-west valley. Except for one small outcrop (Peñasquito), the area is covered by up to 30 m (98 ft) of alluvium.

Jan 1, 2009

By Kira Mizell, James R. Hein, Tracy Conrad

"The Ninetyeast Ridge (NER) extends roughly N-S as a topographic feature for 5000 km, from 31° south to 10° north (Fig. 1) where it becomes buried beneath the Bengal Fan at its northern end. These two geographic characteristics make the NER an ideal natural laboratory for determining the influence of latitude and terrestrial input to ferromanganese (Fe-Mn) crust formation and composition. In addition to study of geographic controls on crust composition, the NER is the largest feature in the Indian Ocean that may host crusts of economic interest.Crusts were collected from 9 of 33 dredge sites from 1.4° north to 26° south latitudes during the 2007 R.V. Roger Revelle Knox06 cruise. Nineteen samples were analyzed for 69 elements each. Nine bulk crusts and 10 layers from four crusts were analyzed. Three of the crusts sub-sampled for layers did not have the bulk crust analyzed and the weighted means for those layers were calculated to obtain bulk compositions. One sample was left out of the statistical analyses because it is phosphatized and chemically quite different from the other samples (Table 1).In order to determine changes in composition with latitude, Pearson product-moment correlation coefficients were calculated for the chemical dataset and latitude of dredge sites, as well as water depth. At the 95-99% confidence level, the following elements increase in crusts moving north along the NER: Mg, Ti, S, Cd, Ni, Tl, Mn, Ba, Co, Cu, In, Li, and Zn; and the following elements decrease northward: Fe, Fe/Mn, P, As, Sc, the rare earth elements plus yttrium (REY), Bi, Ge, and Pb. These correlations indicate that the iron oxyhydroxide component and its associated elements are more prevalent to the south, and the manganese-oxide phase and associated elements increase toward the north end of the NER. This change occurs between dredges D20 and D14 (Fig. 1), with crusts from D20 and south having Fe/Mn !1.0 and those north of D20 ""1.2, with the exception of the phosphatized crust. Crust composition also changes with water depth: Th, Ge, Pb, and the middle rare earth elements (REEs) increase with increasing water depth. Thorium commonly increases in deeper water crusts, which explains the higher Th concentrations in Atlantic and Indian ocean crusts in general compared with Pacific crusts (Fig. 2 and Hein et al., 2012), including the samples analyzed here with a mean water depth of 3584 m. However, water depth does not explain the latitudinal changes because the mean water depths of samples along the northern and southern segments of the NER are roughly comparable. Surprisingly, Si and Al, representing the aluminosilicate/detrital phase, do not correlate with latitude; that is as the ridge approaches and is buried by the Bengal Fan the Si and Al contents do not increase. However, overall, Si and Al have higher concentrations in NER crusts than in central Pacific crusts. Ba can be used as a proxy for primary productivity and statistically does increase to the north along the ridge in the direction of the equatorial zone of high biological productivity. Correlations of Mg, Li, and Zn with latitude may also reflect increased primary productivity at lower latitudes."

Sep 1, 2014

[ ]

Jan 1, 1938

By Wen-Ming Chien

Keywords: AN-KN Phase Transition, Lattice Parameters of AN-KN, X-ray Diffraction The lattice parameters of the low and high temperature phase of KNO3-rich (in NH4NO3) solid solutions have been determined by the X-ray diffraction method. The low temperature single KNO3 phase (KN II) are from 92%-100% KNO3 in NH4NO3 composition range and from room temperature to 393 K showing in X-ray diffraction patterns. The high temperature KNO3 phase (KN I) showed very broad composition range between 20% to 100% KNO3. The lattice parameters of KNO3-rich (KN II and KN I) solid solutions have been calculated at different temperature range. The volumes of orthorhombic KN II phase decrease from 0.3208(3) to 0.3195(3) nm³ at the room temperature as the compositions increase from 95% to 100% KNO3. The lattice constants of the hexagonal KN I phase show that there is no significant change in a-direction when the temperature increases. Details X-ray results and lattice expansion equations during heating will be presented.

Jan 1, 2005

By R. F. Mehl, G. V. Smith

THE decomposition of austenite in steels, because of its immense practical importance, has been subjected to extensive study in recent years from the point of view of the mechanism of the process.1-3 Although much information has been acquired a number of questions, principally of theoretical interest, remain. One is that of the atomic-crystallographic mechanism by which each of the various reaction products forms. The isothermal reaction products of the eutectoid decomposition in plain carbon steels (to which this study is restricted) have conveniently been classified in three general groupings-pearlite, bainite, and martensite. Of these several products, pearlite and martensite have been studied extensively, but bainite has received only scant attention. As a result, the mechanism of the formation of pearlite and that of martensite are now fairly well understood while a great deal of uncertainty exists regarding bainite. PEARLITE Pearlite forms from austenite by the precipitation of alternate platelets of cementite and ferrite, which grow into the austenite matrix.2-5 The rate of reaction may be described in terms of a rate of nucleation and a rate of growth 2 3 Mehl and Smiths have attempted to determine the lattice relationships existing between the ferrite in pearlite and the parent austenite. Using a pole-figure method of analysis, it was found that a limited number of ferrite orientations resulted from the decomposition of a single grain of austenite; it was not possible,[ ]decide between two assumed ideal relationships, both of which appeared to account for the experimentally determined pole figure. It was definitely shown, however, that the relationship obtaining was quite different from that determined for the proeutectoid separation of ferrite.7 No attempt was made to determine the habit plane (matrix plane to which the precipitate lies parallel) of the pearlite lamellae. Belaiew8 earlier had stated that the number of directions assumed by the pearlite lamellae in a single grain of austenite was 12 (no details were given) and concluded wrongly, as Mehl and Smith' have pointed out, that the lamellae delineate the {210} planes of ferrite.* MARTENSITE It is known that martensite is a transitional constituent of body-centered tetrag-

Jan 1, 1942

By J Hadijigeorgiou, R. W. Lawrence, R Pouling

The layered co-mingling method involves the disposal of waste rock with the addition, at predefined construction stages, of layers of dewatered mine tailings. The resulting waste structure displays bulk properties that are more favourable to acid rock drainage (ARD) control than the constituent materials alone. A laboratory test programme was conducted to examine the potential of this method. Columns containing different configurations of waste rock and tailings were percolation leached for 40 weeks and the leachates examined for various parameters. In the short term the chemical reactions that result from the introduction of dewatered tailings into rock waste can significantly improve the quality of the drainage. Columns with co-mingled material produced leachate with pH levels of 8, whereas leachate from the control column containing waste rock alone had a pH of 4. Larger-scale field tests are planned to determine the effect of the disposal method over the longer term

Apr 1, 1996

By S. Bargigli, S. Ulgiati, M. Raugei, F. Cherubini

Metallic magnesium is mostly used in lightweight alloys in order to decrease fuel consumption in automotive applications. Several different production processes are currently used worldwide, and the magnesium production scenario is changing rapidly, with Chinese production increasingly dominating the world market. For the purpose of this paper, a novel approach to Life Cycle Assessment was applied, in which Material Flow Accounting and energy-based methods (Embodied Energy, Exergy and Emergy Analyses) are integrated and complemented, with a detailed description of the environmental hazards associated with emissions from all the different processes.

Jan 1, 2005

By Viviane Tavares

The liquid crystal display (LCD) are currently known by its vast application in electro ? electronic devices, amongst them can be detached the devices of TV, laptops, electronic date, calculators and even though the mobile telephones (mobiles). The mobiles are changed more frequent of the TV for example, this happens due to the technology advance. With the constantly mobile exchange, the batteries, printed circuit board and liquid crystal display accumulation its become an environmental problem. To minimize the environmental impacts caused by mobile telephones residues are considered the segregation process of the LCDs main components, to goal to recover the recycle material. This process involves the use of treatment ore techniques with disc, hammers and balls mills. The process with best efficiency (about 98%) of LCD glass release was the hammers mill. The glass recovered can be used in the glass recycling and the sand substitution in the production of concrete blocks.

Jan 1, 2009

By K. Clifton, K. Kar, M. Gautam, J. T. Jurewicz

"This paper describes the history of LDV measurements employed in research involving gas-solid flows. Much of the discussion deals with measurement techniques employed to obtain separate and simultaneous solid and gas phase velocities. Also, LDV based measurement techniques that arc used to obtain particle size and concentration information in conjunction with the velocity measurements arc presented.INTRODUCTIONThere are numerous examples of industrial processes in which the motion of a solid or droplet dispersed phase in a suspending gas phase is critically important. The applications range from spray droplets injected into combustion chambers to the understanding of the time release mechanisms of particles generated by dissolving pharmaceutical tablets. In many of these processes, the heat, mass, and/or momentum transfer between the dispersed phase and the suspending fluid arc the items of interest. In the past, much of the phenomena were characterized by empirical models derived from flow averaged measurements. Gradual developments in laser Doppler velocimetry (LDV), have provided researchers with an unobtrusive measurement technique capable of obtaining the particle size velocity and concentration with good spatial resolution.In the two decades that LDV instrumentation has been available, most of the uses have concentrated on single phase fluid flow measurements. The light scattered from seed particles small enough to follow complex fluid motions, including turbulence, is converted into velocity information. While the utility of this instrument in single phase flows has been demonstrated beyond question, the use of LDV in gas-solid multiphase flows has had a more gradual development. The measurements ·of interest in these flow regimes are usually the velocity of the suspending fluid as well as that of the dispersed particulate phase. Early investigators were quick to see the potential of this instrument for measurements in gas-solid flows. The interest soon expanded to the development of instruments that could also simultaneously measure particle size and concentration within a two-phase flow field.This paper tracks the historical development of LDV technology as applied to gas-solid flows. The techniques to measure particle velocity, size, and concentration arc treated in separate sections although much of the development occurred simultaneously. Finally, some unique applications conducted at West Virginia University and other locations will be discussed in the application section."

Nov 1, 1995

By Mark E. Smith

Oxide ores can consume enormous amounts of expensive sulfuric acid. The problem is amplified with increasing heap heights. One solution is to provide a thin liner and drainage system between each lift of ore, thereby intercepting the pregnant leach leach solution (PLS) after it exits the active lift. However, these liner systems require special attention to hydraulics, slope stability and geomembrane design criteria. Inadequate attention to the first two can result in reduced recoveries, increased acid consumption andsystem failures. The geomembrane selection criteria are different from the base liner, and optimizing its selection can have significant effects on the operation’s bottom line.

Jan 1, 1996

By J. J. Swanepoel

Titanium nitride in upgraded nitrided ilmenite (bulk of iron removed) can selectively be chlorinated to produce titanium tetrachloride. Except for iron, most other components present during this low temperature (ca. 200°C) chlorination reaction will not react with chlorine. It is therefore necessary to remove as much iron as possible from the nitrided ilmenite. Hydrochloric acid leaching is a possible process route to remove metallic iron from nitrided ilmenite without excessive dissolution of species like titanium nitride and calcium oxide. Calcium oxide dissolution results in unrecoverable acid consumption. The leachability of nitrided ilmenite in hydrochloric acid was evaluated by determining the dissolution of species like aluminium, calcium, titanium and magnesium in a batch leach reactor for 60 minutes at 90°C under reflux conditions. The hydrochloric acid concentration (11%, 18% and 25%), initial acid-to-iron mole ratio (2:1, 2.5:1 and 3.3:1), and solid-to-liquid mass ratio (1:8.33 to 1:2.13) were varied. The results indicate that a hydrochloric acid concentration of 25 wt% supplied in a 2:1 acid-to-iron mole ratio would produce the most favourable upgraded nitrided ilmenite product. The dissolution of iron in this solution reached 97 per cent after only 60 minutes. The total dissolution of calcium and titanium species was 0.01 and 0.11 wt% respectively. Hydrochloric acid can therefore be used as lixiviant to remove metallic iron from nitrided ilmenite. Keywords Titanium nitride, upgraded nitrided ilmenite, hydrochloric acid leaching, metallic iron dissolution.

Jan 1, 2011