Search Documents

By John Kostuik

AT the Sladen-Malartic mine, a number of orebodies have been mined, some by shrinkage and others by open sub-level scopes, from which the ore is handled either through a grizzly system or by mechanical loaders. This paper deals with the comparative costs and relative merits of the two handling arrangements. The facts brought out in this comparison have a bearing on the selection of a proper handling method. The mine is in Fourniere township, northwestern Quebec, about forty miles east of the town of Rouyn. It is served by the Rouyn-Senneterre branch of the Canadian National railways. Two vertical three-compartment shafts give access to the present workings. No. 1 shaft, at which the plant is centralized, is the main hoisting shaft, with five levels to 950 feet. No. 2 shaft, 2,400 feet east of No. 1, is under development, with four levels to 725 feet. At the main shaft, the ore is hand-trammed in 1 1/2 tons cars from the scopes to the stations o:i each level and hoisted in cages to surface at a rope speed of 900 feet per minute. Air-operated tipples are used to dump the ore through grizzlies of 14-inch openings into a surface bin of 150 tons capacity. The ore hoisted at No. 2 shaft is trucked from the headframe bin to the mill. Milling commenced in January, 1938, ar a daily rate of 250 tons. Within two months this rate was increased to the unit's maximum capacity of 325 tons. A second unit to treat a further 325 tons daily was installed in April, 1939. The orebodies mined at No. 1 shaft are parts of a silicified zone at the contact between syenite porphyry and greywacke. The zone is ten co sixty feet wide, strikes easterly, and dips to the south at 55 to 85 degrees. The hanging-wall of the zone is marked, though not precisely, by a strong gouge fault. Locally, the boundary of silicification may be as much as twenty feet either above or below the fault, but for practical mining purposes the fault is the hanging-wall of the ore-zone. The footwall roughly parallels the fault, but as an assay wall it is usually irregular in detail. The ore is dense and hard, a siliceous replacement of both porphyry and greywacke, mineralized with fine disseminated pyrite.

Jan 1, 1941

By R. J. Robbins

The mechanization of hard rock underground mines offers a large potential for reducing cost, improving efficiency, and increasing profitability. However, in spite of serious efforts by quite a number of equipment developers and mining company initiatives, the industry has achieved little real progress. The task is difficult and the blasting alternative to mechanical excavation is an effective and well-developed method, which continues to improve in spite of its inherent limitations. A large number of machines have been built and tried. Only a few developments have succeeded to make a major impact on underground hard rock mining. It is certain that hard rock mines would be laid out and designed quite differently if the mining engineers knew they had available continuous mechanical excavation machines. In the absence of the machines, mines will be designed for excavation by traditional methods. It is not easy to utilize mechanical excavation in a mine which is designed to operate with normal drill and blast excavation. This is certainly an impediment to machine development. But what if an ore body cannot be mined conventionally, simply because the mining company cannot get permits to satisfy the ever increasing strict EIS requirements of the general public and governmental agencies? This may provide the incentive necessary to develop the equipment that will be needed by a new mining method that will have almost no impact on the environment.

Jan 1, 2001

By Herbert Kynor

BY THE term mechanical mining is meant that operation, or series of operations, that replace the hand methods of mining. The first undercutting machine to operate in anthracite was placed in the Butler mine of the Hillside Coal & Iron Co., Dec. 23, 1910, by the Sullivan Machinery Co. The first Jackhamer used in the anthracite field was installed at the Wadesville colliery of the Philadelphia & Reading Coal & Iron Co. in Oct., 1912, by the Ingersoll-Rand Co. The first longwall conveyor was installed at the Dodge mines of the Delaware, Lackawanna, & Western Coal Co. in March, 1912. The first mechanical scraper equipment was installed in the Seneca mines of the Lehigh Valley Coal Co. in January, 1914. The amount of anthracite mechanically mined since the first mining machine was installed in 1910a is as follows: PENNA. COAL Co. D. L. & W., SCRANTON TEMPLE HUDSON YEAR AND HILL- TONS COAL Co., COAL CO., COAL CO., TOTAL. SIDE COAL TONS TONS TONS TONS AND IRON, TONS 1920 372,737b 367,000d 322,892 74,127 371,878 1,508,634 1919 950,786 no record 306,616 81,575 319,356 1,658,333c 1918 917,778 744,966 24,880 44,756 288,781 2,021,161 1917 757,940 838,800 5,050 57,279 164,180 1,823,249 1916 286,780 860,663 13,960 114,173 101,475 1,377,051 1915 428,819 592,169 8,253 1,029,241 1914 219,188 153,896 373,084 1913 171,505 171,505 1912 124,267 124,267 1911 40,319 40,319 1910 1,184 1,184 a. A slightly greater production than shown was obtained as the tonnage from individual operations is not shown. b. Decrease due to strike conditions in 1920. c. Does not include tonnage of D., L., & W. d. D., L., & W. decrease in 1920 due to having less mining machines in operation. There are about 150 undercutters in use in the anthracite region, 80 mechanical loaders, and 10 longwall conveyors.

Jan 9, 1921

By Richard E. Gertsch

Mechanical mining holds great promise for the mining industry. Realizing this promise depends on developing the tools needed to mechanize a mining operation with a reasonable expectation of success. Mechanical mining entered the 1990s with new machines, new operating methods and new ideas for the future. Mechanical mining can provide higher production, increase safety, reduce roof support requirements, create smoother openings for better ventilation, substitute continuous production for cyclical drill-and-blast procedures, and create opportunities for automatic and teleoperated control. The full promise of this important technology still lies ahead. Obstacles include: • Long-term production prediction: Mechanical systems have a high capital cost. Although recouped by lower operating costs, the tradeoffs are not always clear to mine operators. • Cutting tools for hard rock: Rock of more than 103.4 MPa (15,000 psi) cannot be cut by flexible mining machines. • Machine designs: Many machines cannot convert the required power into rock cutting capability. • Engineering: Better use of the machines in the mine is needed.

Jan 1, 1994

By L. Gertsch, R. Gertsch

Mechanical mining is steadily gaining usage in the mining industry. A variety of machines currently finds employment: tunnel boring machines, roadheaders, continuous miners, surface miners, and augers. These machines have advantages compared to drill and blast mining methods, including increased safety, lower cost, uniform muck size, and accurately sized openings. A century of experience with mechanical methods has already paid dividends to the coal industry. Current trends guarantee eventual development of true general-purpose hardrock mechanical mining machines. Mechanical miners will become integrated mining systems and will determine the design of mines, when several significant challenges have been met.

Jan 1, 2001

By Y. Rao, Y. Huang, G. Wang, W. Liu

The properties and deterioration in strength of cemented tailings backfill (CTB )in the underground acidic environment under oxidizing conditions were studied. X-ray diffraction analysis and scanning electron microscopy of the surface of the CTB was carried out, and the sulphuric acid corrosion mechanism elucidated. The properties tested included compressive strength, elastic modulus, cohesion, internal friction angle, variation in the hydrogen ion concentration, and stress-strain relationship in different corrosion periods. The damage model of the CTB was established considering the effects of parameters such as corrosion time and strain on the damage evolution. It was found that the compressive strength, elastic modulus, cohesion (binder effect), and internal friction angle increased at first and then decreased with exposure time. In the long term, the peak stress decreased with corrosion time while the peak strain increased; elastic modulus, and deformation modulus also decreased. The damage caused by corrosion and by load were related by means of a mathematical model, which revealed the relationships between sulphuric attack, load, and damage to backfill in complex underground environments. During corrosion, the expansion of gypsum and ettringite caused microfractures in the CTB. With increasing corrosion time, micro-cracks developed and proliferated. The mechanism of corrosion damage was found to be the dissolution of hydrogen ions and a sulphate ion reaction that produces an expansive substance, resulting in deterioration of the strength of CTB.

Jun 1, 2021

By J. P. Sancho, J. M. Duart, J. I. Verdeja, J. O. García

Following a short review of the history of rails used in the transport of passengers and goods, this paper describes the process for rail fabrication, rail structure, and properties, and summarizes the fatigue test curves carried out on rails used today. Also reported is the process for “continuous rail” production using aluminothermic welding via the introduction of weld metal in onsite casting, as a homogeneous melt. Weld characteristics of aluminothermic welding using different preheating procedures—fusion zone, heat-affected zone, microstructure, hardness, slow bend test, and fatigue test resistance (Wöhler curves)—are related to preheating and welding procedures of 700, 900, and 1,100 MPA rail grades. The Locati method is preferred over the staircase method for ascertaining the fatigue limit due to its simplicity. Macrographic and metallographic inspection of broken specimens reveals the reliability of welding techniques and the good metallurgical quality of welds.

Jan 1, 2007

By Meghan McGrath

Third generation advance high strength steels with microstructures of acicular ferrite and retained austenite were investigated and meet mechanical property goals. A good combination of strength and ductility were achieved with duplex ferrite and austenite microstructures where cementite formation was suppressed. Transformation induced plasticity (TRIP) behavior produced rapid work hardening. The mechanical properties of two hot-rolled steels with duplex microstructures were compared and had the following compositions: (1) Fe-0.14C-13.87Mn-1.42Si-3.51Al; and (2) Fe-0.06C-14.2Mn-1.85Si-2.38Al. These steels were cast, homogenized, and hot rolled at 900ºC to obtain a refined microstructure with ultimate tensile strengths and elongations to failure of 865 MPa and 39% and 1,217 MPa and 28%, respectively. The amount of metastable austenite in both compositions decreased after tensile testing from 58% and 28% to 6% and 0%, respectively. Microstructures were characterized using optical microscopy, scanning electron microscopy (SEM), and x-ray diffraction.

Jan 1, 2010

By Alfred Annor

Deep mining requires innovative approaches in ground control technology and the search for new ground support materials including backfill. There is a need to look at mine waste materials that may be available in deep mines to assess their suitability for use as composite backfill. Composite materials are widely used in all areas of engineering because of their unique and often superior structural properties compared to those of the singular constituent materials. Over the past few years, there has been a growing interest towards the investigation and use of various types of composite backfill materials as special applications fill in mines. A research project is being conducted at CANMET- Mining and Mineral Sciences Laboratories, Natural Resources Canada, to investigate the properties of potential ground support materials for use in deep mines. As part of this investigation, composite backfill materials were prepared by combining waste rock aggregates and mill tailings in various ratios, to determine their optimal mix proportions for strength development. A few cemented rockfill and straight tailings paste backfill samples were also prepared and were used as controls for the study. Two sample sizes were used for the investigation in order to evaluate the scale effects on the material behaviour. A set of samples were cured at 44 EC to simulate the anticipated temperature conditions in deep mines. A second set of samples were cured at 23 EC to provide engineering reference data. The test results show that compared to either the cemented rockfill or the straight tailings pastefill material, the composite backfill samples were the strongest and stiffest of all the test materials investigated in this study. The composite backfill samples also produced the lowest void ratio and porosity values compared to the cemented rockfill and the straight tailings backfill material. This paper will present the results of the laboratory investigations to date. It will also outline the on-going work at CANMET - Mining and Mineral Sciences Laboratories to further assess the ground support potential and viability of using composite fills in deep mines.

May 1, 2003

By Hidefusa Takahara, Koichi Miyake, Dierk Raabe

"Mechanical properties of copper wires were examined. The copper wires containing 5-10 mass % chromium and 1-3 mass % silver were produced through heavily cold deformation. It was expected that the copper wire was easily fractured during cold deformation because of the existence of brittle chromium phase in the alloy. In fact, the copper wire was fractured due to large work hardening, when the true strain [n] exceeded 5. However, the copper wire annealed at 1273K for 6 ks ·in the middle of deformation process could be smoothly drawn to 11=8. After precipitation treatment for silver phase at 473k for 1.8 ks, the wire was able to further drawn to n=8.4. The final deformed wire showed tensile strength higher than 1200MPa.IntroductionDownsizing of electronic devices has led to the demand of finer and higher strength materials for cables. Conventional copper alloys have about 800MPa in ultimate tensile strength. These strength are mainly obtained by precipitation hardening. Nowadays, a process for higher strength wire has been developed, where dual phase copper alloy is used. When it is drawn heavily, the' second phase is elongated along drawing direction and the wire gets high strength due to fiber reinforcement (1). That alloy is so called in-situ formed fiber reinforced ·alloy. Cu-Ag(2), Cu-Nb(3) and Cu-Cr(4) systems are well known as such alloys. It is also well known that chromium is brittle material except single crystal and high purity of chromium. However, Mihara et al. C5l have achieved 1 GPa in ultimate tensile strength in the Cu-Cr-Zr and Cu-Cr-Ti alloys by appropriate thermo-mechanical processing.In this study, the Cu-Cr-Ag systems were investigated: The alloys contained 10 or 5% chromium and 3 or 1 % silver. It was demonstrated that silver precipitated in copper matrix contributed on further hardening."

Jan 1, 2000

By M. V. Swain, N. Bristow, R. D. Dukino

During mining, crushing and handling the size of iron ore lumps decreases. Key factors in determining the amount and size of fines that are produced are the mechanical properties of the ore. In a continuation of earlier work on the same ores the mechanical properties of three Australian iron ores from Yandi, Koolan and Mt. Whaleback were determined. In particular, fracture toughness was investigated in greater detail by examining its relationship to crack length using the compact tension test. The elastic modulus and strength of the ores were also determined in flexure and compression. The results were interpreted using Weibull statistics, enabling the ores to be ranked according to strength and elastic modulus. These results, together with data on the mechanical response of the ores to stress and observations concerning the effect of mineralogy on cracking, provide a coherent understanding of the mechanisms involved when the ores fracture

Jun 18, 1905

In 1997, the Australian coal industry through Standards Australia committee MN-001 Coal and Coke recognised the need to produce a Standard giving some instruction on how to inspect and audit mechanical sampling systems. A Guide was developed by sampling subcommittee MN-001-04 and in 1999 the Standard was released as AS4264.5 æGuide to the Inspection of mechanical sampling systemsÆ Coal and Coke. Since that time the author has assisted with other committees in developing the Guide for other commodities such as concentrates and a generic standard for particulate materials. (AS4433.6 released 2000). The Coal and Coke guide is also currently a work item for ISO Standards. This paper is focused primarily on auditing and inspection procedures for coal mechanical sampling systems. It highlights the need for at least a three level inspection protocol where the operators manning the system maintain operational checks, the operators are regularly supervised by the company managing the system and once per year an independent auditor inspects the whole system to ensure compliance with design and standards. It does not cover short- and long-term maintenance of individual systems. With companies already certified to the ISO9000 series, this guide forms the framework to bring the operation and inspection of their mechanical sampling systems into line with these principles.

Jan 1, 2005

By Diogo Tenório dos Santos

This property has been studied to characterize the strength a metallic material exhibits when it is machined so it can be regarded as its typical behaviour. As such, it may even be considered as an intrinsic material property. It is usually measured by an index called Coppini index, which is expressed by the ratio between the removed mass of a cutting tool caused by wear when it is used for machining and its initial one for a certain set of machining parameters. In this investigation, the tests were therefore conducted by an established set of parameters, namely feed rate, cutting and depth rates, in which the same wear mechanism took place in both ferrous alloys: AISI 4140 and AISI 316 steels. They were chosen based upon their increasing ordinary machinability indexes. The initial and final mass of the cutting tool were measured by an analytical scale with 0.01 mg precision. Cylindrical rods of 50-mm diameter were machined and the CI indexes showed a remarkable difference between them: 0.080 for the first steel and 0.049 for the second one, i.e., AISI 316 steel presented better machinability than the first one. It was then possible to conclude that this method presents good results in terms of both reproducibility and adequacy for machine shop conditions and it may be applied in a foreseeable future, mainly for metallic materials that have rather low machinability indices.

Jul 31, 2018

By Mathieu Dubé

Good mechanical strength of green iron ore pellets is required to avoid breakage and excessive deformation during their handling and further processing. However, green balls with good resistance to handling are often too plastic, which impacts the bed permeability in induration furnaces. Measurements of plasticity, bed void fraction and green ball sphericity as well as bed permeability were carried out on various samples of green iron ore pellets having different mechanical strength. Results show that bed void fraction, sphericity and permeability all depend, to some extent, upon green ball mechanical strength (plasticity). Understanding and controlling the mechanical strength of green iron ore pellets would then help to maximize both the productivity of the induration process as well as the quality of fired pellets through a more stable firing process. Results of research work carried out at COREM, with the objective of improving green ball characterization methods, are presented in this paper.

May 1, 2007

By Jiongtian Liu, Jianjun Wu, Yongzhou Wan, Li Feng

"Mechanical Thermal Expression (MTE) is a developing non-evaporative lignite dewatering technology. It has been shown to effectively dewater high moisture content in low rank coals via the application of mechanical force and thermal energy at elevated temperatures. In this paper, the dewatering behavior of Yunnan Xiaolongtang lignite during the MTE-process was studied. Furthermore, how variations in temperature and pressure during the MTE process affect the surface oxygen functional groups and pore structure were also discussed using Fourier transform infrared spectrometer (FTIR) and mercury intrusion porosimetry (MIP). Increases in MTE temperature and pressure resulted in significant reductions in residual moisture content and moisture holding capacity, along with the increase of fixed carbon content and reductions of other elements content, especially oxygen content, which have been largely attributed to the destruction of the surface oxygen functional groups and porosity in lignite. The optimized technology conditions are temperature 150~220°C and pressure 7~10MPa. The residual moisture content of the lignite treated by MTE under the conditions of 200°C and 10MPa is decreased to 8%, while the dewatering rate exceeds 76 % and the calorific value approaches 22 MJ/kg. The experimental results offer a deeper understanding of the influence of process parameters on the lignite stuctures and properties. The reduction in residual moisture content, surface oxygen functional groups and pore volume under increasingly severe MTE conditions are suggestive of the structure changes that accompany increased coalification (rank) within the lignitic range."

Jan 1, 2014

By M. Ghoreychi, X. Daupley

ABSTRACT: The paper is devoted to two major aspects related to the abandonment of salt mines: 1)- Long-term risk associated with the mechanical instability of surface and its consequences for public security and properties. 2)- Long term dissolution and transport of salt resulting from its communication with groundwater. Basic characteristic features of salt deposits and mining methods are presented through the studies already undertaken on French mines. This analysis allows to identify major hazards encountered in different traditional salt mines and solution-mining cavities. In particular, the role of overburden (presence and thickness of salt layer in exploitation roof, presence of clayey rocks or hard rocks e.g. dolomite or anhydrite), presence of water-bearing strata and possibly natural brine levels, discontinuities, etc. are discussed. In the second part, the main features of mechanical behaviour of salt (creep, damage) as well as transfer processes of this material are presented. The influence of these aspects on the long term evolution of abandoned salt mines is then analysed. KEY WORDS: exploitation, abandonment, salt, mechanical, stability, transport, solution, brine. ZUSAMMENFASSUNG: Der Artikel bezieht sich auf zwei bedeutende Aspekte beim Salzabbau: 1)-Das langsfristige Risiko zur Bodenoberflächeunbeständigkeit und sein Einfluss über Mensch= und Gütersicherheit. 2)-Die langsfristige Auflösung und Beförderung des Salz beruhen sich auf Studien über französiche Bergbauen. Diese Analyse emöglicht es, die bedeutendesten Risiken in verschiedenen Salzgruben zu identifizieren, bzw. Traditionellen oder durch Auflösung abgebauten. Insbesondere wird die Rolle des Deckgebirges (Vorhandensein und Dicke von Salzschicht am Dach des Grube, Beisein von Tanlager oder hartem Gestein wie Bitterkalk oder Anhydrid), Beisein von wasserhaltigem Boden und/oder gesalzenen Wasserflächen, Trennflächen, usw… erötert. Im zweiten Teil werden die haupsächlichen Eigenschaften des Salzverhaltens (Kriechen und Beschädigung) beschrieben. Ihr Einfluss über das Verhalten von stillgelegten Bergwerken lässt sich analysieren. SCHLÜSSELWÖRTER: Bergwerksbetrieb, Stilllegung, Mechanik, Beständigkeit, Ausbreitung, Aussolung, Solewasser. RESUME: L’article est consacré à deux aspects majeurs liés à l’abandon d’exploitations de sel : 1)- Le risque d’une instabilité à long terme de la surface du sol et son incidence sur la sécurité des personnes et des biens. 2)- La dissolution à long terme et le transport de sel sous l’effet d’une communication avec des eaux souterraines. Les principales caractéristiques de gisements et d’exploitations de sel sont présentées en s’appuyant sur les études antérieures réalisées sur les exploitations en France. Cette analyse permet d’identifier les risques majeurs rencontrés dans différentes mines de sel traditionnelles ou exploitées par dissolution. En particulier, le rôle du recouvrement (présence et épaisseur d’un banc de sel au toit de l’exploitation, présence de terrains argileux ou de roches dures telles que la dolomie ou de l’anhydrite), présence de terrains aquifères ou de nappes salées éventuelles, discontinuités, etc. sont discutées. Dans la deuxième partie, les principaux traits du comportement mécanique du sel (fluage, endommagement) ainsi que les processus de transport de ce matériau sont présentés. L’influence de ces aspects sur le comportement à long terme d’exploitations abandonnées de sel est ensuite analysée. MOTS CLES: exploitation, abandon, mécanique, sel, stabilité, transport, dissolution, saumure.

Jan 1, 2003

By A. P. E. Dirige

The stability design of cemented backfills is normally conducted using conventional approaches. Analytical or numerical models, backed by trial-and-error methods, are the primary means used to describe or predict the support performance of backfills during mining. The stability of paste backfill free-standing faces is a major concern due to potential consequences to production, ore dilution and safety. Available analytical or mathematical models are developed based on assumptions of the failure modes that may occur when vertical fill faces are exposed during adjacent mining. Numerical modeling serves to provide an understanding of backfill strength and deformation behaviour. Such approaches offer inherent limitations and generally result in conservative designs. In this paper, centrifuge physical modeling was conducted not only for performance evaluation studies, including stability analysis, but to develop an understanding of the strength and deformation behaviour of paste backfill exposed faces when the adjacent ore zone is removed. The failure mode and mechanics of failure observed in the centrifuge model of a given prototype situation are discussed in detail. Centrifuge model results were compared to numerical modeling and it was concluded that a sliding block failure mechanism that resembles a circular slip appears to be the predominant failure mode.

Aug 1, 2013

By Aziz NI, Guo H

Most of the existing models of the mechanisms of drilling and cutting processes are oversimplified in both stress state and failure criterion. On the other hand numerical modelling techniques are a more versatile method with great potential for development. In reviewing drillability and predicting performance of excavation machines the empirical tests, which simulate the physical breakage action in excavating processes are seen to be the best in terms of penetration rate predictability. Future methods of determination of drillability should concern the breakage characteristics and rock abrasivity involved in the two basic types of attack, i.e., percussive and rotary drilling.

Jan 1, 1988

By S. P. Singh

The purpose of the cut is to provide a free face to which the remainder of a development or breasting round can break. The results of field testing in drifts and at a quarry face were used as a basis for a description of the rock breakage and flushing mechanism in the cut. It was concluded that the important features of a cut design are proper hole spacing, sufficient relief volume, drilling accuracy and relief holes slightly longer than the planned length of the round. The void space provided by the relief holes should be about 15% of the cut volume, with more required in weak, highly fissured rocks. The importance of drilling accuracy increases with round length, an error being magnified by the small blasthole spacing. The first hole pulls only about 20% of the round length, 4-6 holes having to be fired before the cut is pulled close to its design depth. The first four blastholes should be fired with a minimum inter-hole delay of 100 ms to provide progressive relief of burden and avoid the superimposition of ground vibrations. The earliest-firing charge should be closest to the relief area and act laterally, while the first of the vertically-fired charges to be detonated should be the uppermost. Problems during cut-pulling include sympathetic detonation, dynamic pressure desensitisation, charge disruption and freezing of the cut

Dec 1, 1995

By Guanghui Li

In the paper, the recovery technology of gallium from zinc-leaching residue by cold-bonded coal-based direct reduction process following magnetic separation was developed. The results show that the scattered metal Ga can be concentrated obviously after the reduction of zinc-leaching residue briquette and magnetic separation of reduced product. At the same time, the volatilization of Zn in the residue is enhanced during the reduction. When the residue, bear¬ing 18.60% Zu.21.18% Fe and 527 g/t Ga, was reduced with coal at 1100°C for 150 min, the results of Zn volatilization of 9842% and Ga recovery of 89. 10% were obtained in reduction. After magnetic separation of the reduced product, the concentration of Ga in sponge iron is 2164 g/t, and the separation recovery of Ga reaches 92.42%. The enriched mechanism of Ga during reduction -separation process was studied by using electron microscope, scanning elec¬tron microscope, energy spectrum and mineralogical analysis. The investigations show that there is no formation of independent phase of Ga during reduction process. The Ga occurs mainly in metallic iron phase (the concentration of Ga in metallic iron phase is 0.04%-0,4%), in addition, there exists a little Ga in poorly crystalline sulphide (o.08%-0./5Y& Ow). But Go does not exist in most of glass and silicate phase. The affinity of Ga for metallic iron is the enrichment basis of Go in reduction, and it is also in favor of recovering Go during magnetic separation. Key Words: Gallium Zinc-leaching Residue Cold- Bonded Direct Reduction

Jan 1, 2003