Search Documents

By D T. Froedge

With successive generations of the Iso-Seismic System, we are acquiring more and more information about the actual behavior of blast induced ground, and airborne vibration, as it propagates through the environment. Some of the original “truths” that have been long accepted may have to be \revised.

Jan 1, 1995

A glance at the following chart reveals that because of the continued poor economy, the slump in industrial mineral production continued into 1980. Gypsum was down 17% from 1979; cement down 9%, sand and gravel, 17%, and crushed stone, 11%. All these downward trends reflect the high interest rates and high costs that slowed construction starts. Domestic fluorspar was down 21% and imports off 14% due to the steel iudustry slump. However, potash production was up 8% and phosphate, 5%. Increased drilling activity spurred au increase in barite production of 25%. Most other industrial minerals posted losses with only a few insignificant increases. As expected, prices were higher, reflecting increases due to high costs for labor, supplies, and above all, energy. Increasing energy and transportation costs also had their effect on industrial mineral production. Railroad freight rates increased 16-22% including fuel surcharge; truck rates increased 11-14%a; and ocean freight rates increased 20% for finished goods. The 1979 shortage of boa and hopper cars did not continue into 1980-most likely due to low production of many of the hulk industrial mineral commodities. All in all, 1980 was not a good Year for industrial minerals.

Jan 5, 1981

When I reached Warren after the "de luxe" South American expedition I had little idea what was in store for me. From the large check Thayer had handed me just before I left New York I was pretty sure the future would be good, and that before long it would involve Anaconda. Evidently, Mr. Thayer had left it to Dr. Ricketts and John Greenway to work out the details The next morning Greenway asked me to come to his office and told me that he and Dr. Ricketts had discussed the question and that Anaconda would make me an offer I could not refuse. They proposed to pay me almost $1000 a month, more than twice my current salary. They had agreed that I should stay with Calumet and Arizona for the rest of the year to help with Bisbee development and anything I could to assist with the New Cornelia plans and construction Of course I could not turn down such a flattering offer, as I had about reached the limit of advancement with a much smaller company in anything save a high executive job, and it would be a long time before I could be ready to change from exploration and geology to operating. Greenway and I agreed that I would stay with him for the remaining eight months of 1916 without any particular title but helping in any way I thought would be most useful. Bisbee and Ajo Study It turned out to be a busy half year, in addition to many good times with my Bisbee friends. The Uplift Club did not meet as regularly as in earlier years, but Mason Ross, Jim Lewis, Bill Gohring, Roy Mitchell, Hubert d'Autremont, Arthur Notman, and I did have many "bull sessions" and poker games. I saw much more of Greenway than before and made many trips with him to Ajo and later to the new

Jan 1, 1976

By Fredrick D. Palmer

The World is Turning to Coal Peabody?s View ?We believe the world is increasingly energy-short, led by unprecedented demand from population centers and economic hubs in Asia, the Middle East and South America ?This occurs as:?Traditional energy sources are clearly constrained, requiring coal-based alternatives?Energy-rich nations leverage political gain from their assets, and nations urgently look to improve energy security ?In this environment:?Oil, coal and gas face a greater long-term convergence, ?Coal?s traditional regionalized nature becomes global, and ?Coal?s compact energy form becomes an attractive source for liquids and substitute natural gas ?The world is blessed with an abundance of coal to help meet all human energy needs

Jan 1, 2008

By Steven D. Botts

The paper point out the Antamina's social policies with Huascarán National Park. The project had required the mine engage with the communities most affected by the mine development, its operation, and closure. In this sense, operating within this social context has required Antamina to first be effective in understanding who the affected people are –at the local, regional, national and international levels. This understanding is also a process that requires time. Through the HWG, the company has achieved engagement, as well as an understanding an appreciation of viewpoints and perspective that has resulted in the protection of HNP, as well as the timely development of the project, with support of stakeholders. Therefore, the experience of the HWG was become for other natural resource projects in complex settings, involving national and international stakeholders and protected or sensitive areas.

Sep 13, 2001

By Carlos León, David Estrella, Javier Linares

"Recently, Antamina has completed an expansion program of its operations which increased the thoughput in grinding from acapacity of 109 to 130 ktpd. After commissioning, throughput could be exceeded in grinding and downstream processes but primary crushing became a major bottleneck to the overall production process.With an objective to increase the processing capacity of the primary crusher system, a multidisciplinary team was formed with members of Mine, Concentrator and Maintenance departments, who analyzed the overall context of this process restriction. The main implementations developed were: automatic discharge systems of trucks, logic to count trucks and elaboration of a daily performance report. Following implementation of developed improvements, the numbers of discharged trucks to crusher were increased from 449 to 614 units per day. As a result, the expansion target of 130 ktpd was exceeded and processing capacity was increased from 109 ktpd to 145 ktpd. This improvement adds very significant economical value for Antamina.INTRODUCTIONAntamina is a copper-zinc mine located in the Peruvian Andes. Compañía Minera Antamina is owned by BHP Billiton (33.75%), Xstrata (33.75%), Teck Cominco (22.5%), and Mitsubishi (10%). The mine was commissioned in 2001 with a capital investment of US$2.3 billion, and had a nominal 77,000 ktpd mill capacity. Mining, milling, flotation, and tailings impoundment take place at the mine site, which sits at an altitude of 4,300 m above sea level. The deposit is a polymetallic skarn ore body with intrusive phases of quartz-monzonite porphyry into Cretaceous aged limestone. Copper is present mainly as chalcopyrite with a minor bornite component. Zinc is present as sphalerite. Molybdenum is present as molybdenite. Some lead, bismuth, and silver are associated with the sulphides. The deposit is currently classified into six main ore types [Dechert, 2006], grouped into two categories: copper and copper-zinc. The mill produces four concentrate types: copper, molybdenum, zinc, and lead-bismuth. Copper and zinc, concentrates are transported by pipeline down to the port of Huarmey. Molybdenum and lead-bismuth concentrates are bagged and trucked to port."

Jan 1, 2013

By Dave Gilbert

The Antamina tailings beach is considered a fundamental design component, as well as a predictive control for phreatic surface control. In this sense, the paper point out the development and purpose of the tailings beach , as well as what future opportunities may exist. These present and future opportunities, include implications of the beach as an evaporative surface control thus reducing pond volume. These desireable outcomes include better control of the phreatic surface in a rockfill dam, and reduction of pond water volume.

Sep 21, 2013

By Douglas Beahm

Energy Metals Corp. (EMC) holds numerous mineral properties in the northern portion of the Great Divide Basin. The JAB property is one of several potential properties being planned for development as a satellite facility to the greater Antelope uranium project. A National Instrument 43-101 Technical Report was completed for the JAB property. This report estimated total measured and indicated mineral resources on the property totaling 1.6 kt (3,555,022 lbs) U3O8 contained in 2.2 Mt (2.4 million st) at an average grade of 0.073 percent U3O8 at a 0.25 grade times thickness (GT) cutoff in accordance with CIM Standards on Mineral Resources and Reserves. The JAB property is located in Sections 13, 14, 15, 16, 21, 22 and 23, Township 26 North, Range 94 West, approximately Latitude 42° 14’ North and Longitude 108° 00’ West (Fig. 1). This property consists of unpatented mining lode claims and Wyoming state mineral leases com-prising approximately 850 hm2 (2,100 acres).

Jan 1, 2007

By Terry S. Cory

This report covers antenna design, analysis, and development work suited for use with a wireless radio communication system operating at medium frequency. The work includes the test and evaluation of prototype vehicular antennas developed during the program.

Jan 12, 1978

Jan 1, 1965

By G. S. Scott

Mine fires have occurred since the mining of coal was begun, and they are still occurring. The resulting economic waste may become considerable (219),3 especially if a fire is allowed to assume major proportions or to get beyond control temporarily. It is important, therefore, to act promptly whenever a fire is suspected and to have every action count. To do this effectively, it is necessary to know at the earliest possible moment and thereafter what is happening in a remote or inaccessible area. It is equally important to know before¬hand what may be expected as a result of any proposed combative measure. The logical method of combatting a fire demands the cooperation of both mining engineer and chemist. They should decide the course of action to be taken, drawing upon the mining engineer's intimate knowledge of the physical structure of the fire area, the cost and time required for proposed operations, and the probable efficiency with which they could be carried out, and upon the chemist's knowledge of the results to be expected therefrom.

Jan 1, 1944

By S. A. Sanderson

The last two decades have witnessed the resurgence in popularity of a century old tool for shaping laws and public policy – the ballot initiative. In recent years, anti-mining special interests have used the initiative process to secure voter approval of measures to ban modern surface mining for gold and silver. In November 1998, voters in Montana approved such a measure1 – the effects of which have been devastating to the mining industry in that state. In November 1999, anti-mining groups sought to place a nearly identical provision on the general election ballot in Colorado. They did not succeed, but the battle over mining’s future continues in the most important forum of all – the court of public opinion. The Colorado measure failed, in large part, because its proponents failed to convey a positive environmental theme. The mining industry also exercised early-on the rights available under state law for administrative and judicial review of the initiative, instead of relying upon the limited relief that would have been available had it waited until after the secretary of state approved the measure for the November election ballot. This article will summarize the ballot initiative process in Colorado and the proceedings that took place over Initiative No. 215.

Jan 1, 2001

By Ronald E. Heuer, Debra L. Virgens

INTRODUCTION Behavior of clay soils in response to tunneling is reasonably well understood by reference to the tunnel stability factor NT = Pz/su (Peck, 1969; Heuer, 1974). With this analysis tool, care must be taken to use a value of clay shear strength which represents the actual mass strength, considering such factors as slickensided fissures often found in stiff and hard clays. Behavior of clean sand and gravel soils is also reasonably well understood. Above the water table these soils must be assumed to act as running ground unless they are known to have significant cementation or have a very dense and angular interlocked grain structure. Below the water table they must be tunneled using some form of groundwater control such as dewatering, grouting, freezing, or internal fluid pressure in the tunnel such as compressed air or a slurry tunneling machine. The internal fluid pressure must approximately balance the external water head. Without such precautions these soils behave as flowing ground and may yield large volumes of water flow into the tunnel. A wide range of very fine sand, silty sand, cohesionless silt, and clayey sand soils exist in nature in a variety of geologic environments. The behavior of these soils in response to tunneling, and guidelines for anticipating their behavior, are not well described in the literature. Because of their content of fine particles, these materials may behave as if they initially have appreciable cohesion and moderate to low permeability. They may exhibit significant standup time, and require tunnel internal fluid pressure (compressed air or slurry pressure) less than the full external water head. It is important to be able to estimate the behavior of these soils when planning construction methods. For example, if the external water pressure is 140 kPa (20 psi), but soil stability at the tunnel face can be achieved as a compressed air pressure of 80 kPa (12 psi), a large cost savings may result.

Jan 1, 1987

By B. St. Pierre

"The alchemists' symbol for antimony is a diamond with a dot in the centre. The latin name ''stibium'' gives this mineral its chemical symbol ""Sb"" and the name to the principal ore containing antimony. This is Stibnite, a sulphide of antimony, and the valuable mineral at the Consolidated Durham operations. Stibnite chemically pure contains 71.69% antimony metal.Antimony is used in many forms, as an alloy in the production of metal products and as chemical compounds of oxides and sulphides. In Biblical times, antimony was used as a medicine and as eyebrow makeup.Today, the largest single use of the metal is as a hardener and strengthener of lead, and corrosion inhibitor in storage batteries. New applications for antimony in its oxide form as fire retardants are broadening the overall demand especially in the chemical, plastic and fabric industries. Other users include the Military for such things as tracer bullets, shrapnel, smoke screens and flame throwers. An unusual property of the metal is that it contracts when heated which has made it a valuable alloying metal in the printing industry, for heat shields on re-entry vehicles used in the space programmes, and also for the manufacture of bearings."

Jan 1, 1977

By M. L. Leblanc, J. F. Burzynski, D. J. Mossman

A strong heterogeneity in the distribution of Sb+/-Au deposits exists within the North Atlantic Acadian-Hercynian domain. This is reflected in the regional disparity in Sb production among the various producing countries. This work focuses on the nature and distribution of Sb+/-Au occurrences in the Acadian-Hercynian domain. A summary listing of the general features of Sb-Au deposits found in this area is given

Dec 1, 1991

By C. S. Simons

Manufacturers of filtering, thickening or clarifying equipment, have been active in developing machines to meet increasingly rigid operator requirements, and the innovations resulting from this effort are moving into commercial applications. In general, the results of these applications are reported to be good. Little has been reported on progress in theory. The growing insistence on the part of pollution control agencies that waste water discharged into streams contain less and less suspended solids is being felt by a broad cross section of industry. A new clarifier, based on the often rediscovered fact that suspended solids settle more rapidly in inclined channels, is being marketed by Neptune MicroFLOC of Corvallis, Ore. This unit employs modules of inclined tubes, mounted in the upper zone of the clarifier, which carry the water flow. These were developed for light solids, such as those encountered in domestic water treatment and in paper mill waste water. In these applications, flow rates up to about three times those permissible in conventional clarifiers are reported to give comparable overflow turbidity. By combining these units with mixed media filters, high clarity may be obtained with minimum capital. Use of such units in the metallurgical industry, particularly where water reuse or effluent quality is important, should grow.

Jan 1, 1970

By Brad Wells, Wayne Bull, Wayne Dickinson

"Antiscalants were evaluated for control of calcium carbonate (CaCO3) in gold processing applications. Under severely supersaturated conditions, 100 percent inhibition was achieved with 30 ppm antiscalant. Laboratory and field testing established that an antiscalant could both inhibit scale buildup and remove an estimated 0.5 kg/m2 per annum of pre-existing scale. A program was developed to control CaCO3 at a gold mill experiencing severe scale buildup. Annual accumulation of as much as 3 cm of scale in process piping was reduced to unmeasureable levels when 10 ppm antiscalant was applied. No scale-related upsets in mill operation occurred during a five-month trial period.INTRODUCTION Inorganic mineral scale is a crystalline deposit that forms when dissolved mineral constituents exceed the solubility of the respective mineral phase. Formation of mineral scale adversely affects a wide range of industries and is of particular interest in mining and metals processing. Scale affects numerous stages of metal extraction processes. Restricted flow in piping, nozzles, valves, screens, pumps and other components used to transport mineral slurries, metal concentrates, and tailings as well as scale in millwater and thickener overflow circuits are primary concerns (Alfano & Boffardi, 1994). Heap leaching, comminuation, flotation, vat leaching, carbon adsorption, and heat exchangers as well as oxidation steps used in processing sulfidic ores are among key unit operations that may be adversely affected (Simmons & Gathje, 2003). Antiscalant chemicals are designed to prevent formation and growth of mineral scales such as CaCO3. These chemicals, which include two primary classes – phosphonates and anionic carboxylate polymers and copolymers - are added to the gold processing stream at low parts-per-million (ppm) concentrations to interfere with nucleation and growth of scale forming crystals and to disperse fine particulate material. Application points may be located throughout the gold extraction process. Evaluation of the performance of antiscalants plays a critical role in determining the best product for a specific application. Performance evaluations include laboratory testing, pilot scale studies, in-plant trials, and ongoing performance monitoring during mill operation."

Jan 1, 2014

By W. H. Dickinson

The performance of seven antiscalants spanning a range of chemistries was evaluated for control of calcium carbonate (CaCO3) formation in gold processing applications. Three preferred chemistries were identified which provided up to 100 percent inhibition in static jar tests when applied at 30 ppm dosage. The three products were further evaluated using a model carbon extraction circuit developed for this application. The test circuit enabled direct measurement of calcium carbonate formed on the carbon from a supersaturated solution under dynamic conditions. The antiscalants lowered CaCO3 buildup on the columns by 15 - 26 percent compared to untreated controls. Impact of the antiscalants on the rate and extent of gold loading onto a carbon adsorbent was evaluated in laboratory carbon-in-pulp (CIP) studies. The antiscalants generated a 25 - 35% increase in gold loading at gold extraction efficiencies up to 65%. On-site testing at a gold processing facility demonstrated that 10 ppm of the preferred antiscalant was able to fully suppressCaCO3formation in thickener overflow water.

Feb 27, 2013

By Davi Alves Marques

Este trabalho visa analisar a temperabilidade dos aços ABNT 1045 e ABNT 4140 através do ensaio Jominy e correlacionar suas propriedades com a variação microestrutural devido ao gradiente de transferência de calor através dos corpos de prova, também como analisar o efeito dos elementos de liga presentes. O ensaio Jominy foi realizado segundo a norma ABNT A255-10. Foi observado que o aço ABNT 4140 apresenta maior temperabilidade que o ABNT 1045 devido à maior profundidade de têmpera e, por conseguinte, apresentou produtos de transformação martensítica em profundidades maiores do corpo de prova. Visto que o teor de carbono em ambos os aços é aproximadamente igual, a maior temperabilidade do ABNT 4140 se dá devido aos elementos de liga presentes. Os elementos de liga do ABNT 4140 contribuem para uma maior percentagem de carbono equivalente, quando comparado ao ABNT 1045, deslocando assim o diagrama de transformação isotérmica para a direita, reduzindo então a taxa de resfriamento crítico.

Oct 30, 2017

By Vicente Palacios

Southern Perú es el productor de cobre más grande del país y una de las 10 principales empresas cupríferas del mundo que mantiene un complejo minero-metalúrgico en el sur del país (Tacna y Moquegua). Sus principales instalaciones son las minas de cobre con sus respectivas concentradoras en Toquepala y Cuajone, las instalaciones de lixiviación, extracción por solvente y electrodeposición en Toquepala, fundición y una refinería en Ilo. En ese sentido, el presente texto señala el análisis del cobre a través del método secuencial como una herramienta que define el modelo minero y mejora los parámetros de extracción de cobre lixiviable de acuerdo con la clase mineral. Asimismo, mejora del diseño mineralógico y geológico, sobre la base de lo cual se planea desarrollar pruebas de lixiviación de acuerdo con las características del mineral y su relación con el IS, como herramienta para estimar las recuperaciones a escala industrial.

Sep 13, 2001