Search Documents

CSA mine, which is a deep level copper operation, located 12 km north of Cobar, NSW, currently uses a top down stoping method, utilising cemented hydraulic backfill (CHF) to fill and stabilise the stoping void thus assisting the extraction sequence. The stope sequence then requires development back through the CHF stope so that the necessary infrastructure for the subsequent stoping, such as raise bore pads can be sited. The primary and secondary support installed in the CHF consisted of 100 mm thick fibrecrete from floor to floor with 7 + 2.4 m long resin support tendons installed at 1.5 m ring spacing. This support system relied on the resin achieving a quality bond with the CHF, and also the fibrecrete developing early structural strength due to the use of an accelerator. In addition to the delays in the excavation turn around time, it was felt that a superior support system could be designed. Such a system was designed; risk assessed, tested underground, and trialled in selective CHF digouts, and eventually signed off as the chosen support method in CHF digouts. This paper discusses the change from a passive support system used in CHF digouts to an active support system using Swellex bolts and weld mesh, which has provided an active support system, that is superior, faster to install, reduced the excavation turn around time and is overall a cheaper support system.

Nov 25, 2010

By Joseph B. Cummings

"Occurrences of fluorite on the Packard property were first examined by an engineer3/ of the Bureau of Mines in July 1943 as the result of receipt of an application for an access road. In August of the same year the showings were examined by a geologist4/ of the Federal Geological Survey. The property was again examined by an engineer5/ of the Bureau of Mines in March 1944. This last examination resulted in a proposal that access be gained by construction of a truck trail and that the Bureau of Mines undertake to explore the fluorite showings.The truck trail was constructed by the Public Roads Administration, which began the work on February 17, 1945, and completed it 8 days later.The Bureau of Mines exploratory program was completed on May 16, 1945. It consisted of stripping overburden, trenching, test pitting, tunneling, sampling, and topographic mapping.In addition to being described in some detail, the extent of the work as well as results are shown in accompanying tables and figures.Mrs. Rhoda A. Packard, Mrs. Nora 1. Cline, and C. B. Pettingill, all of Tonto Basin, Ariz., own the property, which comprises four contiguous, unpatented lode mining claims recorded at Globe, Ariz., as the Walnut and the Bluebird 2, 3, and 4. The claims are situated in T. 6 N., R. 11 E., Gila County. David L. Roscoe of Tombstone, Ariz., holds a lease and option to purchase.Access to the property is by Highway 88 from Globe, 34 miles to Roosevelt, thence 24 miles by a graded county road along the west side of Roosevelt Lake to Tonto Basin. Here the Greenback Ranch road, constructed by the Forest Service and maintained by the county, crosses Tonto Creek and continues easterly to the foothills. The truck trail leaves the road 8.5 miles east of Tonto Basin and runs 2.5 miles in a southerly direction to the property. (Fig. 1.)The fluorite deposits lie in and along a small canyon in a rough, rocky area at an altitude of about 3,400 feet, Vegetation is scant and of the usual desert variety. The summer climate is dry and hot and the winter climate moderate. Rainfall at the Forest Service Station in Tonto Basin was 11.4 inches from May 1944 through March 1945."

May 1, 1946

By Fumito Tanaka

The Mitsubishi process is the sole pyrometallurgical process for the continuous production of blister copper from Copper concentrates and has been successfully operated around the world. The development of calcium ferrite slag (CaO-FeOx-Cu10), the so-called "C-slag", has enabled continuous converting from matte to blister copper in the commercial scale operations. Commercial interests in the slag led to many papers over the CaO-FeOx slag. However, Cu2O bearing slag has not been studied well due to experimental difficulties. The authors have quantified the thermodynamic properties of the CaO-FeOX-Cu2O system. The results have been utilized to analyze various issues related to the converting furnace, such as the magnetite precipitation from the slag or from blister copper and to develop better controlling criteria for the continuous converting operation. -

Jan 1, 2003

By L. A. Stinnett

An investigation of hazardous surface openings of abandoned and inactive underground mines in the Black Hills area of South Dakota has revealed: (1) tracing legal ownership of mineral claims via county courthouses is confusing, complex, and oftentimes misleading, (2) in general, the selected mine openings in this investigation are to be considered relatively high in risks and hazard potential which poses a threat to the general public, (3) mine closure procedures and designs can generally be categorically implemented depending on the overall situation of the particular mine opening with subsequent unit costs estimates, (4) few preventive state or federal legal measures exist to date concerning mine closures, and (5) liability damages relating to mine opening accidents usually involve expensive and complex common law cases.

Jan 1, 1979

By Charles B. Manula

Judging from the rapid pace of increased demands for mineral products, technological forecasting will become an increasingly necessary tool in mining. Even though the mining industry in 1966 produced more are than ever before, current extraction rates are only a fraction of what is expected in the later years of the twentieth century. If metal and mineral commodities continue to hold their respective and present share of markets, the prospect of coping with demands from a population that will double in the next thirty years can become an impossible task when viewed outside the limits of technological advance and change. Those mining companies that are doing little to develop new and expanding horizons for their operations cannot expect to survive. Nearly 90% of all metals and mineral products consumed last year was recovered by open-pit mining. This has placed great pressure on this segment of the industry which, consequently, has resulted in some spectacular developments. Already production rates at many places are dwarfing those of the Panama Canal and other well-known earth moving projects which are frequently identified as massive undertakings. With projects of this scale, the need for increased sophistication of engineering, planning, management and administration of modern mining installations has never become more apparent. The design of complete systems for the mine and plant that fit the mould of today's business and social environments is undergoing an evolutionary process.

Jan 1, 1968

By Serhan Guner, Sundar Chiluwal

Although significant research has been conducted on helical piles, there is a lack of research and official design provisions on the helical pile-to-pile cap connections. These connections may govern the global response of pile cap systems—especially in tall and light structures where uplift forces dominate the response. To improve future industry practice, the objective of this study is to understand the influence of pile-to-pile cap connections on the global behavior of concrete pile caps and develop recommendations for their efficient design. For this purpose, 108 high- fidelity nonlinear finite element simulations are conducted to quantify the influences of bracket type, embedment depths, longitudinal reinforcement percentages, shear span-to-depth ratios, and loading conditions on the load, deformation, cracking, and failure behavior of concrete pile caps. The results indicate that the design configurations involving single bracket type may result in premature concrete cracking around the anchorage zones with a 25% reduction in the uplift load capacity. The investigations also confirm that high reinforcement percentages and low shear span-to-depth ratios result in higher load resistance in all bracket types, and that the load capacities of the double and studded bracket types are similar. For applications requiring the use of lower embedment depths, it is recommended that either double or studded bracket types be used. The research findings have applicability to both helical and micro piles given that both include similar connection types. INTRODUCTION Tall and light structures may experience significant uplift forces at their foundations due to large overturning moments from wind or other lateral loads. Helical piles (e.g., Fig. 1a) can provide a cost- effective, practical, and resilient solution for resisting significant uplift forces. In order to realize the full potential of helical piles, it is imperative that the helical pile-to-pile cap connections (see Figs. 1b, c and d for examples) are properly designed to resist the applied forces. However, there is a lack of research and associated knowledge on the influence of pile-to-pile cap connection detailing on the global response of pile caps.

Jan 1, 2019

By Verya Nasri, Mehdi Bakhshi

"Fiber reinforcement has emerged as an alternative to steel bars in precast concrete segments due to advantages such as saving cost and reducing production time while developing a more robust product with improved handling and long-term durability. ACI recently drafted a new report as the first design guideline on FRC tunnel segments to provide specific guidance for this emerging technology. ACI document offers general information on the history of FRC precast segments from tunneling projects throughout the world; a procedure for structural analysis and design based on governing load cases, and a description of the material parameters, tests and analyses required to complete the design. This paper summarizes the design considerations in this ACI guideline prepared by the authors of this paper as the main contributors. Application of this guideline to design of a tunnel with an internal diameter of 5.5 m (18 ft) results in elimination of steel bars.INTRODUCTIONPrecast concrete segments are installed to support the tunnel excavation behind the Tunnel Boring Machine (TBM) in soft ground and weak rock applications. The TBM advances by thrusting off the completed rings of precast concrete segments that provide both the initial and final ground support as part of a one-pass lining system. These segments are typically designed to resist the permanent loads from the ground and groundwater as well as the temporary loads from production, transportation and construction. Tunnel segments are generally reinforced to resist the tensile stresses at both the Serviceability (SLS) and the Ultimate Limit States (ULS). With traditional rebar, a significant amount of labor is needed to assemble the cages and place the rebar, which results in higher production costs.Fiber Reinforced Concrete (FRC) can be used to enhance the production, handling, and placement of precast concrete segments. This is because of the uniform dispersion of fibers throughout the segment to include the concrete cover, which is very advantageous for resisting the bursting and spalling stresses. These stresses develop as a result of the high loads induced on the segments during the TBM jacking process. The presence of fiber in the concrete matrix helps mitigate against unintentional impact loads during segment handling and tunnel construction operations."

Jan 1, 2016

By Leonardo de Oliveira Turani

A energia eólica, fonte de energia renovável e de baixo impacto ambiental, vem crescendo rapidamente na última década, em especial no Brasil. A conversão da energia cinética dos ventos em energia elétrica é realizada por aerogeradores, que são acopladas em torres, que na sua maioria são constituídas de anéis sobrepostos de aço, os quais são fabricados e montados com o emprego de várias etapas de soldagem. Em função disso, o conhecimento da soldabilidade dos aços estruturais é um fator importante para indústria eólica, dando subsídios para a elaboração de procedimentos que permitam a redução dos custos de soldagem e a seleção adequada dos aços empregados. Este trabalho objetivou a avaliação da soldabilidade do aço estrutural EN 10025-4 S355M através de ensaios mecânicos e metalográficos de juntas soldadas pelo processo de arco submerso (SAW) em duas diferentes técnicas: Single Arc e Tandem Arc. Os resultados mostraram que o aço S355M apresentou excelente soldabilidade, com destaque para o processo SAW Tandem Arc, o que possibilita a maior exploração desta técnica como uma excelente alternativa para a redução do tempo de soldagem durante a fabricação de torres eólicas.

Aug 8, 2018

By Frank R. Field, Randolph E. Kirchain, Elisa Alonso

"There are a number of environmental incentives for increasing recycling, including the reduction of waste, energy and resource use. Recycling can also be advantageous for manufacturing firms in both the short and long term. Secondary material can substitute for primary material, potentially dampening primary material price increases and reducing the pressure for greater primary extraction. This paper examines the potential for and dynamics of recycling for the case of platinum using a dynamic, behavioral simulation model of the primary and secondary markets. Since the secondary supply of platinum depends on a supply chain separate from primary extraction, recycling can diversify the risks of primary supply instabilities. Over time, recycling can cut primary consumption, reduce overall costs to firms, and possibly reduce the impact of price fluctuations upon firms.IntroductionThe benefits of recycling, from the perspective of the environment, are many, and the environmental benefits of increased recycling are considered a step towards increased sustainability [1, 2]. Life cycle assessments indicate that obtaining materials from secondary sources generally requires less energy and has fewer environmental impacts than extraction and refining of primary materials [3]. Analyses of materials flows show that, in addition to landfill volume reduction, recycling reduces primary material consumption, affecting long term materials scarcity [4, 5].The benefits of recycling are not limited to the environmental. Firms can benefit from the lower energy costs of recycling, especially that of metals whose primary extraction and refining are particularly energy-intensive (e.g., aluminum). The routine participation by firms in secondary materials markets (e.g., www.recycle.net) shows that this advantage has not gone unnoticed.Recycling can also benefit firms whose costs can be significantly affected by changes in material prices resulting from material shortages and material scarcity, with potentially permanent effects upon firms [6-8]. This paper focuses on the impact of recycling in the face of platinum scarcity for supply chain downstream firms."

Jan 1, 2008

By H. Haselhuhn

Filtration of hematite ore slurries can be a bottleneck in some hematite processing plants due to inadequate filtration rates caused by the dispersion of fine particles. Flocculation of fine particles in the slurry decreases the specific cake resistance of the filter cake allowing for increased filtration rates. CO2 sparging of hematite slurry was shown to increase the filtration rate by altering the pH and the surface chemistry of the particles. It was shown that an increase in filtration rate of 278% can be accomplished by lowering the pH from 11 to 6.5 using CO2. This was attributed to increased flocculation of hematite and silica particles in the ore.

Jan 1, 2012

By A. Lyndon

Combined loading tests are described to three 1.2m diameter cast-in-place bored piles, 12m long, formed through cohesionless material into stiff sandy clay. The maximum loading conditions imposed at the pile head were 2400 kN vertical, 160 kN lateral and 3120 kNm in bending, corresponding to twice the working load. Settlements, deflections and rotations of the piles were measured during the tests. An interesting finding which the test results suggest is that, in the short term, vertical movement had apparently no marked effect on lateral performance for piles working at design loadings.

Jan 1, 1989

By Thomas V. Falkie, Howard L. Hartman, Bruce R. Palmer, Donald W. Gentry, John E. Frost, Peter T. Luckie, Michael K. McCarter, Lee W. Saperstein

Education in the mineral engineering professions is in the same flux and turmoil as is the entire minerals industry. Overcapacity in some areas, undercapacity in others, and the constant fear of substitution plague education as well as industry. The exercise in long-range planning that The Society of Mining Engineers has undertaken gives an excellent opportunity to examine the problems and the opportunities in minerals engineering education. Charge to the Committee The Educational Activities Committee was asked by the Long-Range Planning Commission (LRPC) to examine SME's future role with respect to "education policy, role and organization, education department, education board, continuing education, short courses, and extension courses." This examination is timely. It follows a reorganization of SME's Education Board designed to make the Board more efficient in its operation, more responsive to the needs of education, and more active in the setting of Society policy on education. In addition, the roller-coaster cycle of boom and bust experienced by the mineral industry in the last decade has been shared by the minerals schools and has created enrollment problems that need to be addressed promptly. Within SME there is much experience on educational issues to draw from and many problems to solve. Major Premise The committee is emphatic in espousing the philosophy that SME should support, in word and in deed, the highest possible standards that can be maintained by the minerals schools. As guardians of the various mineral engineering and scientific professions (geological engineering, geophysical engineering, mineral engineering, mineral processing engineering, and mining engineering), it is appropriate for the Society to be a watchdog for academic standards. One member of the committee put it succinctly, "We need to educate engineers and technologists, not muckers." A vital and profitable minerals industry needs professionals educated by good teachers, equipped with the most modern available methods, techniques, and knowledge, and challenged by their education to be innovative contributors to their chosen profession. Such education occurs only if it takes place in an institution that is vital and challenging. SME can enhance the quality of its membership if it works to maintain the standards of the schools that graduate new members. Education does not end with the award of a degree. It is appropriate for SME to strive for continued technical quality of its membership. To this goal, SME should maintain its attention to the process of licensing professional engineers, and it must continue and expand its efforts in continuing education for the membership. Recommendations for Action The following recommendations were submitted by the committee and then amended slightly by the full commission. The recommendations have support from the SME Board. • SME Education Coordinator and Staff Department of Education - Staff support for education should be provided by someone with experience in engineering education who would be appointed as SME Education Coordinator for all educational activities: accreditation, continuing education, student affairs, and liaison with mineral schools. The Board has approved an Education Coordinator and the position has been filled. • Advisory Committee on Education - SME should recognize, by amending its committee structure, that functions important to education are filled by SME-appointed representatives to the Accreditation Board for Engineering and Technology (ABET), its Engineering Accreditation Commission (EAC), and Technology Accreditation Commission (TAC). It is suggested that these persons, plus the chairman of the Education Council, plus two other persons appointed by the SME Board, form an advisory committee on education. The Board has approved this. • Education Council - The recently organized Education Board, having full agendas for its committee meetings and having

Jan 6, 1984

By W. J. Birch, R. Farnfield

The use of electronic detonators to control blast vibrations has been previously established by many authors. This is performed by determining the optimum delay period between the blast holes for a particular pattern that can accurately control the firing frequency of the blast, which in turn has a direct bearing on the frequency composition of the ground vibrations recorded at a particular location. This was established by Pedgen, Birch, Hosein & Farnfield (2006) whereby like-for-like comparison tests between non-electric and electronic blasts were carried out in a limestone quarry in northern England. They demonstrated that resulting peak particle velocity values recorded at near and mid-field distances were primarily a product of the firing frequency of the electronically initiated blasts.

Jan 1, 2009

By S. K. R. Iyengar

This report presents the results of a study to develop optimal designs for light-weight mine roof supports for use in underground coal mines. A load capacity of 196 kN (22 tons) and a height adjustable between 1.829 m (72 inches) and 2.438 m (96 inches) were taken as the design parameters and the design goal was a unit weighing less than 22.3 kg (50 lbs). Three alternative design concepts were explored, viz. mechanical, hydraulic, and hydro-mechanical and a total of 13 designs analyzed in detail. Steel, aluminum alloy and composites were the main potential construction materials investigated for suitability from structural, life, and safety and other considerations. The designs considered most promising for development were: (i) the mechanical screw-pin type using telescopic tubes and a fine adjustment screw thread section (ii) the all-hydraulic type, of steel, aluminum alloy or aramid graphite construction (iii) the hydro-mechanical design using telescopic tubes and a short stroke hydraulic cylinder for fine adjustment It is shown that by using realistic mathematical models for stress and deflection calculations, it is possible to reduce prop weight to the design goal. The analysis presented for all-hydraulic props is applicable to hydraulic cylinders on all mining equipment and similar machinery. This report includes the computer program and user's guide for analyzing hydraulic cylinders as well as a cross-indexed bibliography on structural composites.

Jan 1, 1978

By David A. Andrews

Coal occurs at many scattered localities in Arizona, California, Idaho, Nevada, and Oregon, but in most of the known occurrences thick coal beds are of small extent and the coal generally contains a high percentage of impurities. The coal beds occur at many different horizons in strata of Cretaceous and Tertiary age. Bituminous coal has been found in several areas, the most extensive of which is the Eden Ridge field of Oregon. Lignite also occurs in many places, but the only extensive deposit is in the Goose Creek field of Idaho, Nevada, and "Utah. The coal reserves of the region are largely of subbituminous rank; most of the subbituminous coal is in the Black Mesa field of northeastern Arizona and the Coos Bay field of Oregon. The Black Mesa field contains more than 80 percent of the coal reserves of all ranks but is remote from both transportation facilities and centers of consumption. Substantial reserves ill the Coos Bay field are favorably situated with respect to transportation and markets. ARIZONA Subbituminous coal occurs in the Black Mesa, Pinedale, and Gallup coal fields in Apache, Navajo, and Coconino Counties, Ariz. (fig. 1). Bituminous coal occurs in the Deer Creek field in Pinal and Graham Counties and in a small area in Apache County at the north-east corner of the State. All the coal beds are in strata of Cretaceous age. The coal in the Gallup field and at the northeast corner of the State lies in the Western edge of the San Juan structural basin. "Vest and south of this basin the coal-bearing strata have been removed by erosion except in high mesas.

Jan 1, 1947

By A. D. Davis, C. J. Webb, C. S. Johnson

The Belle Eldridge Mine is an inactive lead-zinc mine in Spruce Gulch south of Deadwood, South Dakota. Acidic mine drainage (AMD) produced at the site drains into Spruce Creek, a tributary of Whitewood Creek. The site is on U.S. Bureau of Land Management (BLM) property. Extensive fieldwork was done at the Belle Eldridge Mine through the cooperation of the BLM and the South Dakota School of Mines and Technology. The site was extensively mapped to identify physical and environmental hazards such as tailings, waste rock, collapsed buildings, adits and workings. An exhaustive search of the historical records of the Belle Eldridge Mine was conducted. Maps of the under-ground workings of the Belle Eldridge dating from the 1930’s and 1940’s were found. The maps were used to correlate currently collapsed features to old adits and tunnels. Using hand corers and a portable drill rig, waste rock, tailings and soil core samples were collected and depth to bedrock was determined and the total volume of waste and tailings pile were determined. Related work examined the hydrology of the site. The site is very complex hydrogeologically. Numerous underground and surface workings and tunnels add to the complexity. Several seeps are located at the site, one of which is producing AMD. Recharge to the site was studied, and a 100-year flood plain map was produced.

Jan 1, 2000

By Elli Nurminen

In this work the thermodynamics of the metallic sulphate decomposition reactions were studied through thermodynamical calculations and thermogravimetric methods. The decomposition temperatures and mechanisms were determined for cupric sulphate, ferric sulphate and also for industrial flue dust from a copper flash smelting process. The aim was to determine the thermodynamic conditions for sulphate decomposition and to estimate whether the reactions are kinetically likely to take place in the flash smelting process heat recovery equipment. The information is essential in CFD-modelling of the reactions taking place in the boiler and for optimising the process.

Jan 1, 2006

By W. O. Vanderburg

The leasing or tribute system has been an important factor in the development of our metal-mining industry, particularly in the gold and silver mines of the Western States. It has received its widest application in. the early history of many camps and in the last stages of many mines. The system is especially adapted to mining where the ore's occur in narrow veins or are erratically distributed in small bunches or pockets so that selective mining, hand sorting, screening, or hand cobbing is required to produce shipping or milling-grade ore. The leasing system is also applicable to the development of prospects where the owners are unable or unwilling to assume the risks of searching for ore. The virtue of the system lies in the opportunity it affords miners with little capital to get started; at the same time, it rives owners an opportunity to have their property developed at small cost.

Jan 1, 1934

By H. E. Harris

An extensive experimental program was carried out to determine the variability of respirable dust samplers and to determine whether area dust sampling is feasible in coal mines. For sampler variability, it was found under laboratory conditions, that a single dust measurement could be as much as 0.30 mg/M3 from the true value at the 95% confidence level. Under actual underground mining operations, this difference could be as much as 0.52 mg/M3 in the 0 -5.0 mg/M3 range. The results from dust sampling on 175 production shifts involving over 2,500 on-man and area dust samples showed that area sampling is viable, but the field investigation did not establish necessarily where the best area locations were.

Jan 1, 1976

By X. Gu

Mining operations, especially surface coal mines, have great impacts on the local ecosystem and the environment. However, it has been a common practice in mine design that the economic evaluation considers only the operating and capital costs, while the costs incurred due to ecological damage are left out. Such practice underestimates the total cost of mining and ignores the difference in ecological impacts between different mine design alternatives. With growing interest in sustainable development, the mining industry is under increasing pressure to operate not only based on economic and engineering principles but also on principles of sustainability. Therefore, estimating ecological costs of mining and considering such costs in the mine design process is an important step towards reducing ecological impacts at the design stage. The objective of this paper is to quantify the ecological costs of open pit coal mining and to demonstrate the influence of such costs on the ultimate pit design. The ecological costs of mining are estimated based on the areas and types of land damaged by mining activities and the carbon emission from energy consumption. Four major components of ecological cost are identified, namely, lost value of direct eco-services, lost value of indirect eco-services, prevention and restoration costs, and the cost of carbon emission from energy consumption. Necessary equations are given for estimating these costs. An algorithm is described for ultimate pit optimization in coal deposits with near-horizontal coal seams. A case study is presented in which the ultimate pits with and without ecological costs are optimized and compared to show the influence of ecological costs on the pit design outcome.

Aug 1, 2013