Search Documents

With the ever increasing problems of narrowing profit margins, and increased liability, a solution/option to SEE members is needed. It is essential that all members understand the benefits of utilizing explosives in combination with other methods of achieving the required result on difficult rock or concrete removal projects.

Jan 1, 1995

By R. J. Reynik, F. R. Meeks

IN the classical paper1 of Mehl and Rhines entitled "The Rates of Diffusion in the Alpha Solid Solutions of Copper", the authors state: "It has been mathematically demonstrated that the treatment of the data as though the diffusion were taking place between two flat plates instead of radially in a cylinder has no appreciable effect upon the results. Were the bars of a much smaller diameter, a modification of the analytical treatment would have been required." Unfortunately, the errors in the reported concentrations are much too large to neglect, as shown in the results below. A planar treatment of diffusion data assumes that the reference planes separated by a nominal distance (AX) have identical areas. An adjustment must be made on the concentration data should the successive diffusion planes differ in area. The Mehl-Rhines' diffusion samples were cylindrical with copper electroplated onto copper-based alloys. Successive surface areas through which diffusion occurs are in the ratio ri/r1, where ri is the radial distance between the center of the sample and the center of the i th shell to which the host (alloy) atoms diffuse, and r1 is the radial distance between the center of the sample and the center of the innermost (i = 1) experimentally reported shell from which the alloy atoms diffuse. Hence, ri/r1 (i = 1, ..., n layers) is a dimensionless correction factor to be multiplied by the reported concentration data before planar-data analysis is attempted. In the forty-seven samples reported, the original interface between the copper alloys and the electroplated copper was located at a mean distance of 8.255 mm from the center of the samples. The successive layers, machined off the samples, were approximately 0.0762 mm thick. The distance (xi) at which concentration (ci) was reported was always a distance measured with respect to the original interface, that is, with respect to the fixed distance of 8.255 mm. Hence, the as yet undiscovered Kirkendall Effect was precompensated. The values of ri and r1 are therefore given by ri = 8.255 + xi and Y, = 8.255 + x,. The illustrative table below lists the position xi (mm), ri (mm), the value of ri/r1, the reported concentration (ci) in weight percent (only valid for radial analysis of data), and the corrected concentration [c'i = (ri/r1)ci] in weight percent (only valid for planar analysis of data). Similar tables can be constructed for the remaining forty-six samples. The corrected data can be used to re-evaluate the diffusion coefficients for the reported systems.

Jan 1, 1965

By F. A. Patty

[Health and safety hazards from contamination of the atmosphere in places frequented by persons depend to a considerable extent on whether the contaminating agent possesses sense-perceptive properties which will give warning of its presence before it '.an create harmful conditions. If a distinct and easily recognized warning is given in advance of harmful conditions, hazards ace mitigated, but if warning properties are inadequate or absent, the hazards are augmented. When evaluating the hazard presented by a potentially harmful substance used under conditions of possible escape into the air of places frequented by persons, it is therefore necessary to consider the warning properties of the substance along with ether pertinent information such as toxicity, inflammability, physical properties, and mode of use. If the contaminating agent inherently lacks warning; properties it may be possible to impart them by adding to the hazardous substance a small quantity of a relatively harmless substance which has a high warning intensity.]

Jan 1, 1929

By R. K. Wharton

The paper reviews the development of European harmonised standards for fireworks, recent major incidents involving the bulk storage of fireworks which led to research funded by the European Commission, progress with the forthcoming European Regulation on pyrotechnics and potential issues relating to the certification of products within the scope of the new Regulation.

Jan 1, 2005

By F. Heivilin

If the past is the key to the future, we will have ?tough? times maintaining Industrial Mineral reserves we have and proving new reserves around our plants and in new locations. The tough times will come from resources being more difficult to find, more hoops to go thru to make them Proven or Probable reserves. As always, Industrial Minerals require competitive quality, location, and costs. Since in most cases the market has suppliers, you will have to take away customers from their present supplier. This may take years or not happen even with lower cost higher quality raw materials. To determine the finished cost for a new deposit you need to design, determine capital costs, and operating costs for a new plant . Stripping, mining, hauling, processing, and transportation costs are part of the equation. After satisfying that your costs are in line you will need to do production tests to make sure the process works on the ore. You may want to complete permitting before purchasing the property. If you are new in the business you will have to prove you can deliver the right quality, the right quantity, on time consistently year after year at lower cost to take away a customer. Without being in the market this will be hard. The cut off grades to enter a market may be much lower than sale indicates because a competitor often lowers the price to keep you out of the market. We have many more items to check before the new deposits can be put on reserves. Our old reserves will require drilling to check for new products and prove that they do not contain items that would make them unusable for our product line or cause permitting problems. Archeological checks, wetlands, more water discharge testing, county zoning, and endangered species are among many items that have been added to mine permits. There will be more. A 4-6 page mining permit becomes 30-300 pages and consists of 5-15 permits, any of which might be a fatal stumbling block. It is not guaranteed that we can mine what we have on reserves. We may fight and lose. Oil-Dri?s loss in Reno and LaPort?s in England are examples where permitting failed. The NOx, sulfur, and carbon problems are just starting. Dioxin is in the background requiring monitoring on food products to Europe. What other anions, cations, endangered species, and land types are going to be problems in the future are guesses now. What new products are we going to have to test for and cause out of balance reserves? If there are none we probably won?t be here. We are competing for land use with ?Endangered Species?, wetlands, farming, forestry, cities, roads, and hunting. We?ve mined the best quality, low overburden, easiest to mine and process raw materials. The price of land and taxes are increasing. Old royalties are 2-3 times the present acre value instead of 8-10 times the property value when leased. Land taxes are up. It was and is best that we get the land in Fee Simple Title. This isn?t always possible. However, plants are closing and people have overlooked, made mistakes in drilling or interpretation of deposits. These may be opportunities. China is eating up high quality ?Industrial Minerals ?which have caused prices to rise. We may need to change our cutoffs? in terms of smaller pit sizes and higher overburden ratios. This is money in the bank. Overburden ratios and other items increasing cutoff costs need to be rethought. Suddenly doubling cutoff ratios for overburden and decreasing pit sizes are good alternatives to looking elsewhere where we might not be able to mine for a number of reasons. The higher prices make them competitive, especially when a competitor goes out of business. However, our low overburden ratios and short hauls around our plants are not safe from new roads, condemnation by county or city governments (N. J.), zoning changes (Reno, FL., CA, and environmental regulation changes (Buffers GA, MS). New roads ?Interstates? can take reserves, increase hauling distances and reduce tons per load. Let?s combine the Refractories, fullers earth, and bentonite industries and use the last 40 years as a guide to the future looking for problems and opportunities. Some or most of the following will apply to other minerals. WHERE DO WE LOOK? First, on our own properties, those next to our properties and on properties near our competitor?s plants. Where the profit margin has increased, the distance from the plant and thickness of overburden we can use is increased. The thickness of clay is decreased. For new locations we pick the ideal location and look at deposits and closed or open operations in ever increasing distances away from that location. We need to be aware of: 1. Increased transportation costs a. Access to Roads -Backhauls b. Haul with doubles and triples c. Railroads - Loading on sidings - Ability to get switches - Cars/backhauls versus rates 2. Cost of building a new plant 3. Cost of infrastructure 4. Cost of repair or new equipment when purchasing an operating or shutdown plant. 5. Local, state, and federal mine and environmental permitting. When exploring around an established operation expect that property acquisition, drilling, mining, stripping, and hauling costs will be greater due to them having second, third, or even fourth the pick of the deposits. I found this in New Jersey looking for refractories and around Quincy, Florida looking for attapulgite. You may be able to get some better properties because the operating company has angered some land owners, their drillers missed the clay, or the property wasn?t available when they were actively exploring for reserves. You may have some product lines your

Jan 1, 2009

By Kenneth L. Bickel

During an underground mine fire, the importance of controlling the spread of smoke and toxic gases with suitable ventilation structures has been proven. However, under certain conditions, control of the propagation of the fire itself may be even more critical in insuring a safe mine evacuation. Fire doors offer the means for accomplishing both objectives. In 1978, the Bureau of Mines initiated research to evaluate the state of fire-door technology and develop and test a fire door suitable for large openings (10 by 12 ft or larger) in noncoal underground mines. This report discusses current fire-door technology in the context of the underground mine environment and the design, fabrication, lab testing, and in-mine field testing of a mineworthy fire door. This door has a 1.5-h fire resistance rating and limits temperature rise across the door to 2500 F during the first 30 min of fire exposure.

Jan 1, 1987

By J. R. Shultz, R. J. Lambert

One of the present trends in the mining industry is the increased use of mining contractors. In the past, many project owners have utilized mining contractors for topsoil stripping or overburden removal, usually on a short-term or periodic basis. In recent years, mining contractors have not only removed the overburden, but mined the product as well. Why is this change occurring? A prevalent trend in the mining industry appears to be the outsourcing of non-core and non-strategic functions, allowing producers to focus more on areas of technical expertise where higher incremental value is added—that is the processing, refining, and marketing of the product. As capital allocation becomes more critical, this trend is likely to continue.

Jan 1, 2002

By M. Li, J. D. Miller

During the past decade, considerable effort has been made to develop improved flotation strategies for the sedimentary phosphate resources from Florida, particularly the dolomitic phosphate resources. New flotation equipment and alternate flotation strategies have been evaluated. These developments are reviewed for both traditional siliceous resources and future dolomitic resources. Most process strategies involve variation in the reagent sequence and/or the use of depressants/dispersants. Further research and development efforts in flotation technology are needed to increase flotation plant capacity by elimination of the conventional double float process, to improve the recovery of coarse phosphate, and to achieve the desired selectivity with respect to carbonate minerals, particularly dolomite.

Jan 1, 2000

By J. Tumialán

El presente trabajo realiza un estudio comparativo de las propiedades físicas y químicas de tres nitratos de amonio, cuya interpretación se relaciona con las conclusiones sobre estudios de AN-FO realizados en la Universidad de Missuri. Básicamente se evalúa los factores de campo que afectan la performance del AN-FO, como el confinamiento, diámetro del hueco, inicio de la carga y mezcla del explosivo, así como se mide la factibilidad de disparar al AN-FO sin una dinamita. Los tajeos de producción de la mina Casapalca sirvieron de ejemplo para ejecutar dichos disparos, encontrándose que el AN-FO francés es el más adecuado y sensible en torno a la performance de los otros explosivos, dado sus componentes como su ahorro de consumo.

Nov 20, 1972

By Arthur D. FitzGerald

EDC established an Environmental Review Framework in 1999. Throughout the early fall of 2001, the Corporation held public consultations across Canada to strengthen that framework, leading to a public release on November 15, 2001 of a report summarising the results of these consultations. Following this, the Corporation implemented strengthened environmental review requirements in the form of its Environmental Review Directive, in compliance with legislated amendments to Canada?s Export Development Act that went into effect on December 21, 2001. Over the past few years, there has been a global trend towards an increase in the social and environmental requirements of multilateral/bilateral financial institutions and export credit agencies. More recently, this activity has focussed on capturing institutions that have not yet adopted similar requirements and, more specifically, on developing a convergence of the requirements from institution to institution. This paper describes EDC?s new ERD and some of the initiatives that have taken place or are in process that are moving international financial institutions toward converging their environmental and social requirements for projects in the private sector.

May 1, 2002

By J. Galloway, P. K. Hofmeyr

Obviously all mining operations require much analytical work to be carried out. This starts with exploration, becomes more stringent with the evaluation of a mineralised area and finally becomes on-going when mining operations are under way. All these phases are carried out by geologists, metallurgists and mining engineers. They require analyses to carry out their functions but usually have no involvement in the analyses themselves. Analyses are carried out at commercial laboratories or in-house analytical laboratories. In the past in South Africa the tendency was for the larger mining houses to have their own centralised laboratories for exploration samples with each mine having it?s own laboratory to meet only that mine?s requirements. The centralised laboratory maintains QC functions at the subsidiary laboratories. In other mining areas of the world there has been a strong tendency for all geological analytical requirements, especially for exploration and mining, to be carried out at commercial analytical laboratories. In recent years there has been a tendency for mines in South Africa to move in the same direction. This paper discusses the factors that need to be taken into consideration when a new laboratory is being planned and automation is an option. The planning of the laboratory at the new Langer Heinrich Uranium mine in Namibia is discussed considering these factors. 2.0 REQUIREMENTS OF A MINING ANALYTICAL LABORATORY The purpose and requirements of a mining analytical laboratory are fairly obvious and can be summarised as follows :- 1. All mining operations must have access to analytical facilities, either in-house or commercial 2. The laboratory must be able to handle all the sample types submitted by the mining operation These can be mining, exploration and/or plant samples. They can comprise solids (rocks, bore-cores), slurries and/or liquids.

Jan 1, 2007

By Donald O. Capstick

[ ]

Jan 1, 1983

By Thomas Brunsing

The program was carried out to develop deep kerfing and core breaking techniques to be incorporated into the design of a field prototype hard rock mining machine. The field machine is designed to mine non-abrasive bedded deposits up to 20,000 psi in uniaxial compressive strength. The mining technique involves cutting approximately 2 ft deep parallel kerfs spaced 2 ft apart in either a horizontal or vertical direction and subsequently breaking out the cores so defined. The prototype machine is intended for demonstration of the technique in a quarry or equivalent field environment. The program was aimed at minimizing the required kerf width, obtaining reliable breaking within that kerf width and determining cutter blade requirements necessary to achieve a mining rate of 20 ft3/min. Full scale breaking experiments and 1/2 scale kerfing experiments were employed to evaluate the system. High strength concrete test specimens were used to simulate the rock being cut and broken. The test results indicate the kerf/break technique can achieve the desired mining rate by utilizing two 7 ft diam blades to cut 2 in. wide by 24 in. deep kerfs. A lateral load applied at the base of the kerf (base shear) was selected at the core breaking technique to be employed by the full-scale prototype machine.

Jan 1, 1983

By A. E. Dabbagh

Saudi Arabia’s mineral potential offers development target that compliment the national effort to diversify the income of this oil and gas economic based nation. Ma’aden, a joint stock company with paid-up capital of US$1 billion, has from its inception in 1997, actively developed in-house engineering and management skills to transform the Arabian shield’s mineral potential into such real projects. Gold mine operating facilities of 100,000 oz/yr underground and 50,000 oz/yr open pit are de-scribed, as well as 3 targets, two of which are underdevelopment; Al Hajar (3,000 tpd at 2.5 gpt Au)and Al Amar (5,000 tpd at 20 gpt Au). Emphasis is also on exploitation of phosphate rock and down-stream fertilizer products, based on the Kingdom’s107,000 sq. km. northern basin geological reserve. Al Jalamid, the prime target, represents 216 million tonnes of these P2O5 reserves. Saudis and expatriates, together, lead international engineering companies and contractors operating and developing these facilities.

Jan 1, 2000

By L. Wade

The University of Nottingham, in conjunction with the University of Kentucky and The Society of Mining Engineers of America, hosted the International Symposium on Underground Mining Methods and Technology from 8th to 10th September, 1986. The programme was based on the central theme 'Coal Mining under Adverse Conditions'.

Jan 1, 1987

Both here and in Australia, the unique commercial and tax features of joint venture are finding favour in forestry, fishing, technology and infrastructure projects. For New Zealand mining companies, joint ventures provide a means of access to foreign know how and investment funds, while retaining their corporate independence and their hard-earned tax losses.   This paper discusses some of the practical income tax and GST considerations where a joint venture structure is contemplated. The first part of the paper considers income tax, and in particular how joint ventures enable companies to access and carry forward tax losses. It explains why a joint venture may be advantageous relative to a jointly owned company.   The second part of the paper concerns GST and the focus is on two aspects: 1.   Joint ventures may be registered for GST. In some instances they have no choice and are required to do so. Where a joint venture is registered in respect of a taxable activity, the members are not permitted to register in respect of the same activity. This may be problem where the member has incurred its own expenses and the member wishes to register in its own right to claim back the GST on those expenses. This paper explores the issue and possible solutions. 2.   It is not uncommon to see joint ventures claiming GST on the costs of production, and the production being sold (and GST is being charged) by the members. In this paper we consider whether these arrangements have a tax risk, and what can be done to make them technically sound.

Jan 1, 2005

By A. S. Haugh

OHSAS 18001 is a series of international standards for occupational health and safety management. It is comprised of two parts, 18001 and 180029. OHSAS 18001 was formulated by international certifying bodies and is based on BS8800 and was first published in 19996,11. OHSAS 18001 was developed to be compatible with ISO 9001 and ISO 14001 in order to facilitate integration of quality, environment, and occupational health and safety management systems5. It is a voluntary standard and the overall aim of OHSAS 18001 is to enable organizations to control their occupational health and safety (OH&S) risks and improve overall health and safety performance5. OHSAS 18001 is widely accepted in the UK, Europe, and Asia, is gaining momentum in North and South America, and it was used as the basis and conforms to the requirements of ANSI/AIHA Z.10-2005: American National Standard for Occupational Health and Safety Management Systems. It defines a set of requirements for an occupational health and safety management system suitable for any kind and size of organization4. Businesses of all sizes are developing and implementing occupational health and safety management systems (OHSMS) that are in compliance with the OHSAS 18001 standard.

Jan 1, 2012

By A. C. Fieldner

The Sectional Committee on Classification of Coals, functioning under the sponsorship of the American Society for Testing Materials and the rules of the American Standards Association, in its 1934 report recommended to the American Society for Testing-Materials5 that Specifications for Classification of Coals by Rank be adopted as tentative. These specifications, slightly modified as recommended by the Sectional Committee, in its 1935 report,6 wore approved as tentative standards by the society in 1935. The specifications rover the classification of coals according to their degree of metamorphism, or progressive alteration, in the natural eerie s from lignite to anthracite. The basic scheme of classification is according to fired carbon and calorific value (expressed in B.t.u.) calculated to the mineral-matter-free basis. The higher-rank coals are classified according to fixed carbon on the dry basis, and the lower-ran]: coals according; to B.t.u. on the moist basis, that is, containing its natural bed moisture but free of visible surface moisture. Agglutinating and weathering indices arc used to differentiate between certain adjacent groups.

Jan 1, 1935

By E. V. Deshayes, W. E. Young

"INTRODUCTION The Camp Bird mine was investigated by Bureau of Mines engineers 3/ September 22 and 24, 1942, and April 29 and 30, 1944. In a subsequent report and supplement, it was recommended that core drilling be done below the 14th. level to determine if commercial ore existed at greater depths, and particularly if ore existed in the vein or adjacent thereto where it passes into the sedimentary formations estimated to underlie the volcanics approximately 400 feet below the 14th level.Seven diamond-drill holes aggregating 3,956 feet were drilled. Four of these holes were under the Hematite ore body and three were under the Big Discovery ore body. Two holes under, the Hematite ore body wore directed at angles but little steeper than the angle of dip of the vein and penetrated the sedimentaries beneath the volcanics close to the vein. Enough low-grade ore was found at the base of the Telluride conglomerate to indicate the presence of a large body of low-grade zinc sulfide ore. Two holes were directed to crosscut the vein at a depth of approximately 125 feet below the 14th level. No commercial ore was cut, but the vein showed the average width and same general characteristics as at the 14th level. One hole under the Big Discovery ore body was directed to crosscut the vein and test the base of the Telluride conglomerate in the footwall block. No commercial ore was found in either the vein or the sedimentary horizon. One hole was directed to test the base of the Telluride conglomerate in close proximity to the vein in the hanging-wall block. This hole was lost approximately 100 feet short of its objective, and a third hole was drilled to accomplish this same thing. The third hole was stopped approximately 50 feet short of its objective when failure of equipment caused a recess of the"

May 1, 1948

By Nelson Reátegui

El presente trabajo describe los sistemas computarizados utilizados en el centro de operaciones, explotación y beneficio de Hierro Perú, compañía minera localizada en el departamento de Ica. Inicialmente, la función de un sistema computarizado se limitaba a la reducción de costos en la mano de obra y a realizar operaciones básicas en los negocios. Posteriormente, esta situación cambió ya que estos sistemas se utilizan en los niveles de la gestión empresarial.l. Asimismo se explica las aplicaciones de este sistema al comercio, al tipo técnico-científico, así como el cálculo de reservas y el desarrollo del sistema computarizado de performance de equipo.

Nov 20, 1978