Search Documents

By B. H. Clemmons, B. G. Saunders, R. H. Stacy

"INTRODUCTION This investigation was undertaken to determine the response of Birmingham (Alabama) red-iron ore to heavy-medium concentration. Specifically, the work involved a study of the efficiency of the process in separating coarse gangue diluents from the ore and an endeavor to evaluate the potential economic results. The investigative work was not intended, nor is it to be construed, to be adequately exhaustive in scope to enable immediate plant construction. Rather, the primary objective was to determine the grade of ore that could be produced by heavy-medium treatment and the resulting indicative or tentative benefits to be derived from such treatment. The latter, in turn, would determine the merits of the more exhaustive study that would be required for an ultimate decision on the heavy-medium treatment of the ores.The problem of avoiding excessive contamination of red-iron ores by shale and/or ferruginous sandstone has been before the operators of the iron mining industry of the Birmingham, Alabama, district for many years. Within the last two decades, increased mechanization of mining methods has increased this contamination to a considerable degree. In fact, general utilization of scraper loading and other mechanical methods of mining, in conjunction with small increases in the natural insoluble content of the ores, in some cases has actually resulted in the production of ""acid"" or excessively insoluble ore, where ""basic"" or excessively lime ores were produced formerly.The contaminating materials are derived largely from roof spells and natural parting seams in the ore, a condition that to some extent has been aggravated by the irregularity of the ore beds. The latter have been subjected to both primary and secondary folding in many places. Considerable faulting has taken place, also. In many localities these conditions render virtually impossible complete avoidance of ore contamination from the over and underlying sandstones and shales. However, in a few localities, where the ore beds are less disturbed and shale partings are absent, mining can and is being accomplished with relatively little dilution."

May 1, 1948

By L. D. Schmidt, W. C. Schroeder, A. C. Fieldner

"INTRODUCTION The highly mechanized character of modern warfare makes steel the most vital raw material. The shortage of steel scrap in the United States is forcing the use of increased quantities of pig iron in steel manufacture, so that the rate of pig-iron output will continue to be the controlling factor in steel production. 5/ At the same time, the construction of new blast furnaces is limited both by time and the amount of strategic material available. Under such circumstances, every effort must be made to attain and then maintain maximum pig-iron output from the equipment now in use.When forcing a blast furnace to the ultimate in production the highest standards for quality and uniformity of the coke must be maintained. In view of these facts, the Bureau of Mines, in cooperation with the Office of the Solid Fuels Coordinator for War, is surveying the coke industry to study the various steps in producing coke of higher quality and greater uniformity. 6/ The engineers conducting the survey are visiting key men in coke-oven and blast-furnace organizations to determine, first, the major and most common problems in coke production and use; and, second, the best and quickest method for solving them. Various operators have made good progress in solving individual problems, and a Nation-wide exchange of information among them will make possible widespread adoption of the best practices. It is the purpose, of the survey and reports such as this preliminary one to facilitate such exchange of information. As an outgrowth of the survey, it was soon revealed that many operators could be helped by cooperation with various Government agencies, particularly to procure suitable coals, minor additions to equipment facilities, and tests on certain properties of coal or coke, or specific advice concerning the operation of various types of equipment. The machinery and organization necessary for securing this cooperation have been set up as a part of this work."

May 1, 1943

By G. T. Lineberry, L. Adler

Due to safety-imposed constraints on clearances for mobile bulk handling equipment, it is necessary to optimally select a unit based on speed and size. The unit cannot be both large and fast. Since output is proportional to both size (or capacity) and speed, the combination must be carefully examined to maximize output. A simple graphical procedure and a calculus-based solution are presented to accomplish this. While the procedure applies to all mobile bulk handlers, as an example of the solution technique, attention is focused on shuttle cars. Background Major variables To fully define a bulk handling problem, the conditions, equipment, and activities must be characterized. The conditions and activities, when lumped together, are termed "encumbered space," since they "act to impede motion, as with a burden" (Lineberry, 1979). The insertion of mobile bulk handling equipment into what is already a difficult set of conditions and activities compounds the state of encumbrance, as limited space is competed for by many normal and life support systems. Long (1972) recognized the effects of design criteria, including road width, on haulage vehicle speed and, therefore, on production. Velocity -clearance curves Velocity-clearance curves are either available or can be constructed in the field. A preliminary set of curves for average conditions and activities is shown in Fig. 1, where clearances are only for the side of the vehicle (Lineberry and Adler, 1984). These curves set the safe speed limits for a vehicle operating at given clearances, under given conditions and activities. When feasible, velocity-clearance curves should be constructed through field measurement and observation. Curve construction should also consider haulway roughness, distances, and operator skill, as well as loading and dumping characteristics. It should be noted that haulage capacity determination is a total systems problem, not one just dependent on velocity and clearances. Production requirements and company capabilities also influence capacity determination.

Jan 10, 1985

By Nirander M. Safaya

Revegetation success on surface mined lands is dependent upon the nature of the plant growth media. Soil physical and chemical properties dictate the needs for specific reclamation and subsequent management practices. Field experiments were conducted at six coal mine sites in Oliver and Mercer Counties, North Dakota to determine the subsequent effects of a single application of selected amendments on spoil and topsoils over the five year period, 1974-1978. Considerable variations in the physical and chemical properties were found in mine spoils from site to site. The texture of spoils ranged from sandy clay loamy at North Beulah I to loamy at Glenharold, and from sandy loamy at North Beulah 3 and South Beulah sites to loamy sands at the Center site. The pH of the sites ranged from 6.5 at South Beulah to 8.2 at North Beulah 3. In many cases, the pH values of mine spoils were not significantly different from the topsoils. The electrical conductivity (ECe) did not exceed 6 mmhos cm-1 at the test sites even though in other studies much higher values were recorded in the same vicinity. The spoils from Glenharold and North Beulah test sites can be classed as moderately saline, and those from Center and South Beulah as non-saline. The sodium adsorption ratios (SAR) varied from less than 1 to 32, with highest values in the spoils of North Beulah 3 followed by Glenharold; all other sites were nonsodic. Lowest SAR values (less than 1) were found in the topsoiled sites at South Beulah and Center. Spoils of North Beulah 3 test site were highly calcareous, followed by North Beulah 2 and Glenharold. Center mine spoils which were the least calcareous of the test sites, showed the calcium carbonate equivalent three times higher than that of the topsoil. The average calcium concentrations in the spoils of North Beulah 3 and South Beulah test sites were -13 and 14 me 100g -l while at North Beulah 2 and Glenharold test sites 25 and 22 me 100-1-1 were recorded, respectively. The overall magnesium concentrations ranged from an average of 4 to 16 me 100g 1. Sodium concentrations in all sites never exceeded 10 me 100g-1. Phosphorus concentrations on the average at North Beulah 1, North Beulah 2, and Center were 10.2, 4.6, and 22.2 µg g -1 spoil, respectively. Concentrations of potassium ranged from 200 ppm at South Beulah site to more than 375 pp in at the Glenharold site. High concentrations of sulfates (239-2778 µg g-1) seem to contribute to the salinity in these spoils. Chloride concentrations of spoils were low and never exceeded 40 µg g-1 spoil. Based on established critical levels of deficiency for micronutrients in agricultural soils, it seems that none of these were deficient. However, controlled environment experiments did reveal increased plant growth responses when some micronutrients were added to the mine spoils. Treatment effects were highly site specific depending on the nature of the soil/spoil characteristics and, of course, the properties of the various treatments. While slack coal amendment to the spoils at North Beulah 2 site affected significant increases in a large number of variables (both major and trace elements), amendment of the topsoils at the South Beulah test site with leonardite resulted in significant decreases in a number of variables, particularly trace elements. Spoils at Glenharold and North Beulah 3 demonstrated the fewest significant changes due to amendments. Calcium, magnesium, strontium, organic matter and nitrogen were consistently increased from site to site with the addition of lignitic materials. Other spoil/topsoil physical and chemical properties (30 variables) as affected by amendments and time are discussed.

Jan 1, 1982

By Catherine N. Mulligan

Thickening of mine tailings is a relatively new concept for their sustainable management. Removal of water from the tailings to form a paste instead of slurry disposal decreases environmental and geotechnical concerns. As the use of these pastes is relatively new, their behaviour requires investigations such as liquefaction and seismic stability, freeze-thaw behaviour, consolidation and leachate characterization. Slurry density, ore type, particle size distribution, specific gravity and environmental conditions can all influence paste characteristics. In this paper, the effect of the above-mentioned parameters is examined. New developments in water removal, and additives (such as flocculating agents, cements, organics, fertilizers, etc) leading to low moisture content tailings are reviewed, and the potential for thickening to enable sustainable management of mine tailings is discussed with respect to storage volume requirement, use of virgin land, consolidation of the tailings, land use after decommissioning.

May 1, 2007

By Tom Cooney

A small number of mining contractors worldwide have evolved their businesses to be able to provide a ?total service solution? to their clients. Thiess, an Australian-based international mining service provider, works with numerous clients to tailor delivery methods and commercial arrangements to suit individual projects. The benefits of Thiess? extensive experience is brought to each client and project, whilst business improvement within projects, to the mutual benefit of both the client and Thiess, is a key part of all long term contract relationships. Historically, optimal business outcomes were closely related to the achievement of production and cost performance measures. Whilst these remain fundamental to successful mining businesses, other elements of sustainability are assuming increasing importance. As a large energy user, greenhouse and energy management is becoming an important part of Thiess? business. Thiess is a signatory to Australian government initiatives such as Greenhouse Challenge Plus, and is integrating energy management into its operations and business improvement programs, in many cases to the benefit also of the client. This paper will highlight the benefits that an organisation such as Thiess can bring to a mine owner. Thiess? approach to business improvement and cost reduction, sustainability and energy management, as well as the relationship between these will also be considered. Increasingly, overall mining performance is dependent on the alignment of formally disparate elements.

May 1, 2007

By John G. Henning

Unplanned ore dilution has a direct and large influence on the cost of a stope, and ultimately on the profitability of a mining operation. This paper presents results of a study on the influence of a variety of factors on ore dilution in a blasthole stoping environment. A series of 3-D numerical models were developed and analyzed to examine the effect of mining depth, stope geometry and stope setting within the orezone extraction sequence. To quantify modelled ore dilution from the three-dimensional simulations, the ore Dilution Density (DD) is a term introduced in this study to denote potential hanging-wall overbreak. It was found that hanging-wall overbreak is not significantly influenced by depth alone, and that stopes with large or small axial ratios are more stable than large rectangular stopes. It was also demonstrated that, in addition to stope dimension, the amount of unplanned dilution differed according to stope type. Five stope types were identified, based on their position within a tabular blasthole mining sequence. The methodology presented in this paper can be adopted to develop mine-specific design tools for the estimation of ore dilution associated with a proposed mine design. This can prove extremely helpful in the process of underground mine planning and optimization.

May 1, 2007

By James J. Dowd

During and immediately following World War II, the heavy demands for steel required the mining of unusually large quantities of coal for the manufacture of metallurgical coke. The largest demand for metallurgical coke is in the Appalachian region, which comprises central and western Pennsylvania, Maryland, West Virginia, Virginia, eastern Kentucky, Tennessee, and Alabama. This demand is satisfied by coke made from coals within the region; consequently, the reserves of coking coal in this region are being depleted more rapidly than reserves in other coal-producing regions. The supply A' high-quality coking coal during the war was inadequate, and some coke were forced to use inferior coals. The coke produced from these inferior coals adversely affected the rate of production. Another national emergency probably would produce a similar condition, and in the interest of -national security, the Munitions Board of the National Military Establishment requested the Bureau of Mines to evaluate the reserves of coals suitable for the manufacture of metallurgical coke. All bituminous coals in the Appalachian region are coking, and as the coal that produces the better metallurgical coke become depleted, other coal previously considered inferior will be used. The general trend is toward the use of lower-quality coals for metallurgical purposes.

Jan 1, 1950

By F. A. Rutledge

The Millet copper deposit is on the north shore of Iliamna Lake in southwestern Alaska. Copper mineralization occurs in a zone of altered limestone .adjacent to and intruded by a diorite porphyry with some diabase facies. During 1949 and 1950, the Bureau of Mines investigated this prospect as a part of the U. S. Department of the Interior program in Alaska for the development of critical and strategic minerals. Field work was begun August 8, 1949; it was recessed November 28, 1949, because of inclement weather. The work was resumed Nay 28, 1950, and completed July 3, 1950. The program of investigation by the Bureau of Nines included topographic surveying, machine and hand trenching, diamond drilling, and sampling the zones of mineralization. This report outlines the general geology of the area, gives a description of the deposit, and contains the factual data resulting from work by the Bureau of Mines.

Jan 1, 1952

By J. Moyes

The Intec Process is a generic process for the production of pure base metals and precious metals from sulphides concentrates derived from copper, nickel, zinc and lead ores. The development program for the Intec Process initially focussed on the treatment of copper concentrates, (the ?Intec Copper Process?), and more recently of zinc concentrates, (?the Intec Zinc Process?). Developed and proven in Sydney, Australia at a cost of US$15m over the last ten years, the Intec Copper Process is now ready for commercial application. The knowledge gained during the development of the Intec Copper Process has been applied to the Intec Zinc Process, which utilises the same basic chemistry to produce high purity zinc ingot from metallurgically complex zinc sulphide concentrates containing lead, copper, iron, silver and gold. The demonstrated ability of the Intec Zinc Process to treat low grade mixed zinc/lead/copper concentrates, including those with high iron and manganese levels, holds out the real prospect of overcoming major metallurgical hurdles that have long affected the zinc industry. The Intec Zinc Process consists of the three consecutive circuits of leaching, purification and electrowinning. The leach circuit is of single stage configuration with a series of reactors to which concentrate and lixiviant are fed. Purification consists of cementation and precipitation by pH adjustment. Electrowinning employs an electrolytic cell very similar in design to that of the Intec Copper Process, but differs in that a conventional plate cathode is produced. During electrowinning, the same mixed halide species (BrCl2 -, HalexTM) that is integral to the Intec Copper Process is generated in solution at the anode and exhibits powerful leaching characteristics capable of directly leaching the sulphide concentrate feed. The need to roast the concentrate prior to leaching, as is practised in the conventional Roast/Leach/Electrowin (RLE) process, is thus eliminated whilst a range of by-products (notably lead, copper and precious metals) can be extracted in the simple, single-stage leach. This paper describes the Intec Zinc Process; the technology, predicted economics and its environmental aspects.

May 1, 2002

By Earl T. Hayes

[This work represents a continuation of the efforts of the Metallurgical Division of the Bureau of Mines to ascertain and apply knowledge of mineral physics to process metallurgy.]

Jan 1, 1941

By N. S. Kim

Silver paste including nano sized particles maintains conductivity in high temperatures without forming oxide layers. In the industry, printing process produces wasted silver paste inside the cylinder and on silk-screen. Pyrometallugical silver recycling methods have environmental problems and do not extract pure silver after removing polymer and organic materials during the extraction process. In this study a simple wet process, of recycling the waste silver paste, using ammonia, was conducted. Silver ion extraction yield was increased using oxidant in the ammonia solution. Possible extraction yields, such as pH, concentration, temperature of ammonia, oxidant concentration and the extraction time. The particles that were obtained after the extraction process will be used as porous hydrophobic catalytic and applied to AI mask and hydrophobic ink. Keywords: Waste silver paste; Ammonia; Hydrophobic porous support

Jan 1, 2009

By A. Fahimifar, H. Soroush

Abstract: Triaxial tests were conducted on the schist specimens with various anisotropic angles under confining pressures of 0, 7 and 15 MPa, and axial stress-axial strains, were measured and plotted for various conditions. The results obtained reveal the effects of schistose on the strength and deformability of the rock very clearly. Peak strength of the specimens for 00 and 900 schistose orientations are nearly the same. Modulus of elasticity of this rock varies with anisotropic angle. For 0 orientation modulus of elasticity increases to a maximum. Confining pressure increases the peak strength and improves the rock deformability. However, this effect is not the same for various orientations, and there are no similar trends for each anisotropy direction. Analysis of the results shows that consideration of a linear failure criterion such as Mohr-Coulomb is appropriate for the prediction of rock behaviour up to 10 MPa, rather than a non-linear one. The analysis also reveals that the friction angle and cohesion are affected by the anisotropy orientation, and this effect is more important for the cohesion than the friction angles. Resume: Les esseys triaxiales sur les echantillon d un roch schist avec les differents angles non-isotrop sous les tension lateral zero et sept et qoinze mega pascal (mpa) est fait et les covtraite et allongment unitaire sont mesure et leur curues est destine sous different condition les resultats obtenues montre les effets du schistosite sur le resistance et le ductilite vissiblement. Le resistance final sur les echantilions pour les angles o degre et 90 degree est equivalent. Le modoule d elasticite de ce roch sera difere par a port de l angle de stratification. Pour l angle o degree le valeur de modoule est le maximum. le pousse lateral augmenterai le resitance final, et sera amilterai le toleran le de ductilite. Mais cette effet bn est pas unigue pour les different stratification, et pour les diferents directions no– isotrop it n y a pas le meme solution. L analyse des resulitats montre que le criterre de ruin comme mohr–colomb est moderate pour le pousse lateral jusq av lo mega pascal , et ce n est pas neccesaire d utiliser de criterre no–linear . Cette analyse aussi montre que l angle de frottement et cohsion est en relation de la direction no–isotrop, et cette effet est olus important pour le cohsion par a port de l angle de frottement . Abriß : Dreiachsige Prüfung wurde auf den schist Exemplaren mit verschiedenen anisotropic Winkeln unter Bestätigen von Drücken von 0.7 und 15 MPa geleitet, und axiale Spannung axiale Spannungen, wurden gemessen und für verschiedene Bedingungen wurde geplant. Die Ergebnisse haben die Wirkungen von schisocity auf der Kraft und dem deformability des Felsen sehr deutlich erhalten offenbart. Maximale Kraft der Exemplare für 0° und 90 sind° schistos Orientierungen beinahe das gleiche. Modulus der Elastizität von diesem Felsen ändert sich mit anisotropic Winkel. Für 0° vermehrt Orientierung modulus der Elastizität zu einem Maximum. Einschränkender Druck vermehrt die maximale Kraft und verbessert den Felsen deformability. Aber ist diese Wirkung nicht das gleiche für verschiedene Orientierungen, und es gibt keine ähnlichen Tendenzen für jede anisotropic Richtung. Analyse der Ergebnisse zeigt jener Überlegung Kriterium eines linearen Ausfalls wie zum Beispiel Mohr Coulomb passend für die Voraussage von Felsen Verhalten bis zu 10 MPa, anstatt eines nicht linear ist. Die Analyse offenbart auch, daß der Reibung Winkel und Bindekraft werden beeinflußt von der anisotropic Orientierung, und diese Wirkung wichtiger für die Bindekraft ist, als der Reibung Winkel

Jan 1, 2003

By R. E. Mitchell

Environmental Impact Assessment (EIA) is the accepted method for evaluating proposed mining and other industrial projects to obtain regulatory approval and to help companies plan for responsible development. Another evaluation system becoming increasingly more common for proposed projects is the Environmental, Social and Health Impact Assessment (ESHIA). An ESHIA differs from an EIA for its more comprehensive and inclusive approach to evaluate potential impacts on public health, and its ecosystem services approach to assessing biodiversity impacts. An ESHIA may also be required by certain lenders for financing major projects. Conducting an ESHIA for a proposed mining development is not without its challenges, with costs, scheduling, regulatory concordance and other constraints to be considered. This paper examines some benefits and challenges of ESHIAs and summarizes lessons learned using a case study approach.

Jan 1, 2012

The most complete mining show ever held in the United States and the largest exposition of its kind to be held anywhere in the world in 1988. That's how the American Mining Congress is billing its "MINExpo International '88," to be held April 24-28 at Chicago's McCormick Place, the largest exposition facility in the country. MINExpo International '88 will combine for the first time two previously separate AMC-sponsored shows - the International Coal Show and the International Mining Show. Starting with the 1988 show, MINExpo International will be held every four years. The next show, in 1992, will be held in Las Vegas. The MINExpo in Chicago will feature more than 500 mining equipment and services exhibits covering 3 hm2 (320,000 sq ft) of exhibit space. Exhibitors will display products ranging from small safety devices to large earth-moving equipment. MINExpo is one of the few trade shows selected by the US Department of Commerce for its Foreign Buyer Program. Commerce is working with US embassies around the world to publicize MINExpo and to form delegations of visitors from many countries. Overseas visitors to the show will be assisted at an on-site International Business Center. It will provide currency exchange, translation, and other services to foreign buyers. Registrants at MINExpo will also be able to attend their choice of 27 morning-only program sessions. At these sessions, international mining experts from industry, government, and academe will analyze technical, strategic, and policy matters and discuss the outlook for the industry. "Toward the 21st Century" is the theme of this year's program. The technical workshops and managerial seminars are designed to assist mining executives, engineers, and geologists as well as mine superintendents, managers, and foremen in handling their responsibilities. Based on previous attendance at AMC international mining shows, the association says that more than 25,000 persons are expected to attend the Chicago show. It is expected that approximately 15% of the attendees will be from foreign countries. The Soviet Union will be among those exhibiting at MINExpo. The Russians have leased more than 2.8 dame (3000 sq ft) of space to display their mining machinery and equipment. It is the first time that the Russians have joined in an exhibition of mining equipment in the US. The two largest manufacturers of mining equipment in the Soviet Union, Setmash and Avtoexport, will put on display in Chicago a variety of Russian-made equipment. It will range from 100 t (110 st) heavy-duty dump trucks and diesel engines to drilling, hoisting, and conveying equipment. In addition to some 400 US exhibitors of mining equipment and services at MINExpo, nearly 100 companies will be present from other major mining nations such as Australia, Canada, Great Britain, Japan, the Netherlands, and West Germany. And, for the first time, a Chinese manufacturer will take part in the AMC show, participating with its US marketing partner.

Jan 3, 1988

By David Humphreys

It is difficult to overstate the importance of China to the future of the world mining and metals industries. In a remarkably short time, China has risen to become the world?s largest producer and consumer of steel and its second largest consumer of non-ferrous metals such as copper and aluminium. It is currently the world?s largest buyer of copper on international markets, the second largest buyer of iron ore, and the third largest buyer of alumina. At the same time, it is the world?s largest or second largest producer and exporter of tin, lead, zinc, magnesium and a host of minor metals and industrial minerals, as well as a fast-growing exporter of coal.

May 1, 2002

By L. D. Tracy

This paper represents work conducted by the Bureau of Mines in cooperation with the Illinois Geological Survey and the Engineering Experiment Station of the University of Illinois.

Jan 1, 1926

An Atomic Force Microscope (AFM) was used to measure the surface forces between glass sphere and silica plate in CnTAC1 (n=12, 14, 16, 18) solutions. The results showed the presence of long-range attractive forces that can be fitted to single exponential functions. With a given surfactant, the attractive force increased with increasing concentration, and reached a maximum at the point of charge neutralization (p.c.n.). The decrease in the attractive force above the p.c.n. is probably due to the inverse orientation of the surfactant molecules. A plot of the log (p.c.n.) vs. the number of carbons in the hydrocarbon chains of the Cn TACI homologues showed a linear relationship with a slope of -0.37, indicating that the surfactant adsorption entails a decrease in free energy by -0.85 kT per mole of CH2 (or CH3) group. These results suggest that the adsorption of long-chain surfactants is controlled by hydrocarbon chain association during the process of forming surface hemi-micelles (or domains). Possible origins of the long-range attractions are discussed on the basis of the results presented in this communication.

Jan 1, 2006

By Sara J. Davenport

With the increased demand for mercury incident to preparations for national defense and the reduction in imports from some of the usual sources owing to war conditions, many small mines in the United States Pure now being worked that ordinarily would be unprofitable. This is indicated by the following table on mercury produced in the Unite States in 1939-40 (1)4/

Jan 1, 1941

By J. Girard-Dwyer, T. Camm

Direct costs such as medical, legal, administrative, and worker’s compensation costs, property damage, lost earnings, and lost benefits are typically used to compute the economic impacts of occupational injuries. However, there are also a number of less obvious, indirect costs that substantially contribute to the overall loss costs. In fact, for every $1 of direct costs an estimated $3 to $5 of indirect costs are also incurred. This paper presents a systems approach that incorporates engineering, economics, psychology, and sociology in order to evaluate the total value of investments in safety. By studying the interrelated system comprised of the injured worker, their family and coworkers, as well as the organizational structure that was the setting for the incident, a methodology can be developed that will more accurately capture the true costs of mine injuries.