Search Documents

By Bruno Bussière, Michael Aubertin, Robert P. Chapuis

Covers with capillary barrier effects (CCBE) have been used in recent years as gas barriers for the isolation of wastes, including reactive mine tailings. Capillary barrier effects help to maintain a high degree of saturation in the moisture retaining layer, which then reduces gas flux. Various factors affect the degree of saturation of the moisture retaining layer in a CCBE, such as the material water retention characteristics and layer thickness. Slope geometry can also influence the hydrogeological behaviour of a CCBE, but this factor has frequently been ignored in the past. In this paper, the authors show some results of a numerical study that illustrates the influence of slope on the behavior of capillary barriers made of different types of material. The numerical model calculations are based on an actual case of a CCBE constructed in northern Quebec. This investigation shows that the water content profile is greatly affected by the position along the slope. Thus, it is necessary to evaluate the influence of the geometry to properly establish the performance of a cover system.

Jan 1, 2000

Authority to Prospect 57P lies within the Surat Basin',' an eastern lobe of the Great Artesian.Basin, a major Mesozoic . downwarp that,had its inception'in Triassic time. The northern edge of the Mesozoic Surat Basin overlaps the southern extension of the Bowen Basin, a 'major structure that warped do*nWard in varying degrees from Permian time into Early'Triassic time: The axis of the Bowen Basin may be superimposed on the axis'of a still older structure, the Tasman Geosyncline, that probably originated in Ordovician time culminating in Late Carboniferous time.Within. or bordering the area the geologic record 'clearly marks.major differences in the stratigraphy and structure related, to"the successive evolution of these three distinct structural units. Three major phases of sedimentation have been recognised; one related to the development of the Tasman Geosyncline froi'n. Devonian to.Early Permian time (Horton group), one related to-the development of the Bowen Basin from Early Permian to_Early Tri= assic time (Bowen group), and one related to the development of the Great Artesian Basin from Triassic to Cretaceous time (Great Artesian . Group).

Jan 1, 1962

By J. F. Stenebråten, W. P. Johnson

Carbonaceous material (CM) from the Barrick Goldstrike Mines, NV, was characterized with respect to its gold sorption (preg-robbing) and gold recovery behavior. The breadth of graphite peaks measured by X-ray diffraction were used to calculate crystallite dimensions (002) of the CM. The (002) dimension was found to vary inversely with preg-robbing activity and directly with gold-recovery behavior, indicating that the degree of graphitization (maturation) experienced by the carbonaceous material is correlated with gold-loss during ore processing. The inverse correlation of preg-robbing activity was improved when percent preg-robbing was regressed against (002) crystallite size and carbon content. The (101) crystallite dimensions of all samples were calculated from laser Raman analysis, and were not found to correlate with preg-robbing behavior of the CM. BET surface area and micropore size distribution results were affected by grinding history, negating comparison of these characteristics between samples.

Jan 1, 2000

Provide a rapid, reliable means of warning underground miners of a fire or other emergency. Approach An ultalow-frequency electromagnetic signaling system was designed, breadboarded, and tested at various under around mines. How It Works Current fire warning systems for underground mines, such as stench, audible alarms, and messengers, arc slow, unreliable, and seldom achieve total mine coverage. An ultralow-frequency electromagnetic fire warning alarm system with true through-the-earth signaling capabilities was developed to solve these problems. The system was originally designed for high-back room-and-pillar mines where stench systems are unusable due to the low velocity of mine air flow. However, the system has an application to all underground mines.

Jan 1, 1988

By John K. Adams

Phosphorus may be incorporated into sedimentary rocks in at least four different ways: (1) by the accumulation of detrital mineral fragments, (2) by the accumulation of phosphatic organic debris, (3) by diagenesis and (4) perhaps by the primary precipitation of calcium phosphate. Based-on the petrographic examination of Cretaceous and Tertiary sediments from the northern and central parts of the Atlantic Coastal Plain, Diagenesis is the most important of these mechanisms. Both syndiagenesis and epidiagenesis are required to explain the origin of all the diagenetic phosphate mineral species which occur in the northern and central parts of the coastal plain. Syndiagenesis produced much of the coastal plain's apatite. It was operative below the sediment-water interface while the substrate was being compacted. Compaction forced pore waters, which were enriched in phosphate by the decomposition of organic matter, upward through calcareous sediments. The PO43- radicle replaced the CO23- and calcareous nodules, pellets and shell fragments were converted to apatite. Epidiagenetic reactions occurred in the subaerial environment where downward percolating meteoric waters carried phosphate in solution to cites where cation activity was sufficiently high to form new minerals. Vivianite may form where ferrous iron is available and wavellite and variscite may form in the presence of aluminum rich minerals. Textural evidence suggests that many of the reactions were repeated. The present day appearance of apatite, vivianite, wavellite and variscite in the coastal plain may represent several generations of diagenesis.

Jan 1, 1972

By D. K. Ingram, G. L. Mowrey, T. R. Rehak

Problem: Blasting is a hazardous component of surface mining. Serious injuries and fatalities result from improper judgement or practice during rock blasting. This paper describes several fatal injury case studies, analyzes causative factors, and emphasizes preventive measures. Method: This study examines publications by MSHA, USGS, and other authors. The primary source of information was MSHA’s injury-related publications. Results: During the 21-yearperiod from 1978 to 1998, the mean yearly explosive-related injuries (fatal and nonfatal) for surface coal mines was 8.86 (95% CI: 6.38 -11.33), and for surface metal/nonmetal mines 10.76(95% CI: 8.39 - 13.14). Flyrock and lack of blast area security accounted for 68.2% of these injuries. This paper reviews several case studies of fatal injuries. Case studies indicate that the causative factors for fatal injuries are primarily personal and task-related and to some extent environmental. A reduction in the annual injuries in surface coal mines was observed during the ten-year period of 1989 - 1998 [5.80 (95% CI: 2.71 - 8.89) compared to the previous ten-year period of 1979 - 1988 [10.90 (95% CI: 7.77 - 14.14)]. However, such reduction was not noticed in the metal/nonmetal sector, i.e., 9.30 (95% CI: 6.84 - 11.76) for the period 1989-1998compared with 11.00 (95% CI: 7.11 - 14.89) for the period 1979-1988. Discussion: A multifaceted injury prevention approach consisting of behavioral/educational, administrative/regulatory, and engineering interventions merits consideration. Impact on industry: The mining community, especially the blasters, will find useful information on causative factors and preventive measures to mitigate injuries due to flyrock and lack of blast area security in surface blasting. Discussion of case studies during safety meetings will help to mitigate fatal injuries and derive important payoffs in terms of lower risks and costs of injuries.

By Carl G. Bock

INTRODUCTION Rapid transit systems involving near surface tunneling in hard rock are becoming more numerous, especially along the northeast corridor of the East Coast. Tunneled systems are under construction in Washington, D.C. and are being planned for Atlanta, Buffalo and Baltimore. Near surface tunneling is defined for this paper as being that in which the crown is 100 feet or less below ground surface. For Rosslyn Station, the total cover ranged from 52 to 70 feet. The rock cover, however, ranged from 40 to 50 feet which is slightly less than the station height and about two-thirds of its width. Rosslyn Station (Fig. 1) is the only station excavated completely in hard rock in the Virginia portion of the 98.5 mile Washington Metropolitan Area Transit Authority's (WMATA) rapid transit system. The station site, oriented in a north-south direction beneath a main thoroughfare and flanked by multistory office buildings, was fixed by the need to serve a dense population center at a specific location and geologic conditions were a secondary consideration in siting. There was no previous underground rock excavation in the Washington Metropolitan Area of the size and scope of Rosslyn Station that offered a practical case history guide to the geologic conditions and excavation problems to be encountered. GEOLOGY The regional geology of the Washington Metropolitan Area is divided into two physiographic provinces by the northeast trending Fall Line (Fig. 2). Northwest of this boundary is the Piedmont Province

Jan 1, 1974

By J. Girard-Dwyer, J. Johnson, J. Whyatt

The choice of fragmentation method is one of the most fundamental aspects of mine design, and often has a major impact on the safety and economic viability of an operation. Almost exclusively, underground mining operations rely on either mechanical excavation or drill and blast techniques to extract rock. Each of these fragmentation methods has distinct advantages and disadvantages, and each is appropriate, and economic, for different mining conditions. However, the choice of fragmentation method can have a pronounced effect on the amount of damage created in the rock mass surrounding the opening. This paper reviews a number of case studies where both mechanical excavation and traditional drill and blast were used in underground mines. Ground support requirements in the mechanically excavated areas are compared to the support requirements in the blasted sections in order to demonstrate the potential safety and cost benefits of the various fragmentation methods.

Jan 1, 2003

By B Lindqui, M V. Knyazev, L S. Tsemekhman

Gipronickel Institute JS that is a Research and Development Centre affiliated to the worldclass Norilsk Nickel Mining and Metallurgical Company, and Outokumpu Technologies AB (Boliden Contech AB) have jointly developed the reconstruction project of Pechenganickel metallurgical operations using a two-zone Vanyukov furnace. The international expert group appointed by the Nordic Investment Bank has examined the project. The project financing should be partly executed by the Norway government. Current annual rate of sulfur dioxide emissions is 100 000 t. The aim of the project is to reduce it to 12 000 tpy. Pechenganickel Combine is owned by MMC Norilsk Nickel. Currently it produces nickel high-grade matte from sulfide copper-nickel concentrate with up to ten per cent MgO content. The existing production is in accordance with the following flow sheet: agglomeration û electric furnace smelting with matte production û converting in horizontal converters. Annual production capacity is about 36 000 t of nickel in high-grade matte. Converter gases report to sulfuric acid production. The principal results of studies on high magnesia materials smelting in two-zone Vanyukov furnace, engineering solutions, and technical and economical parameters are offered.

Jan 1, 2004

By Whitworth N, Anderson P

New plant has been commissioned to treat off-gases from the Fluo-solids Reactor in the Copper Smelter. The new section of plant was built onto an operating system and commissioned with minimum disruption to production. Under construction is a 270 m tall stack for Lead Smelter gases. Additional items for the Lead Smelter will include a new gas cooler, a central baghouse to replace Sinter Plant wet gas scrubbers, a new exhaust fan on the main baghouse, and ducting of drossing gases to the main baghouse. Emphasis is given to discussing improvements the new plant has made to working conditions, the general environment and increased production capability. Total expenditure in the two smelters is in the order of $25 million.

Jan 1, 1978

By Richard P. Curtin, Madan M. Singh, Francis S. Kendorski

INTRODUCTION The use of roof and rock bolts to reinforce the strata is an established method of rock support in both underground and surface excavations. However, the need to drill a hole, extract the drill-rods, and then place the bolt is time-consuming and costly. This becomes even more significant if the bolting is repetitive and extensive as in coal mining. Though the main thrust of this development was directed towards coal mining, the basic concepts are also widely applicable to all excavations. The authors, therefore, feel that this innovation should be of interest in rapid excavation and in tunneling. In the case of coal mining, it has been established from past statistics that the roof-bolting operation is the most hazardous activity. This is primarily because of the operator being exposed to unsupported ground. It is evident that remote installation of roof bolts would markedly improve the safety of the operation, if accomplished more readily with self-drilling bolts rather than the conventional two-step variety operation. Thus, in addition to increasing productivity, this development can be considered to be a milestone towards further improvements. The objective of this program was to establish the technical and economic feasibility of self-drilling roof bolts for use in coal mines. It might be clarified at the outset that this work was, therefore, directed primarily at showing that workable self-drilling bolts with less cost can be developed, which could be effectively used in mines. It was not to fabricate a production model bolt.

Jan 1, 1979

By William Laird

The predominent method of coal mining in the United States for years has been room-and-pillar mining. The reason for this has been the advantages of room-and- pillar method which is a relatively flexible system and its capital investment. The room-and-pillar method permits some selectivity in mining, especially where gas wells, faults and possible coal quality may be a factor. The mobility of continuous and conventional mining equipment used to develop entries may also be used for retreat mining of rooms and pillars. Longwall mining of coal takes place along a long straight face, or wall, blocked out between two butt or panel entries. The long faces or walls are normally projected in lengths of 61 to 183 m (200 to 600 ft) in this country. The longwall method of mining had its beginning in the United States during the 1800's. During that period, pack wall and wood posts were used for roof support. The longwall face was mined by miners using picks to undercut the coal. To keep the coal face from turning over, short wood posts called sprags were set in a slant position as the coal face was undercut to the depth of two to three feet. When the under-cutting cycle was completed, the sprags were removed to permit the coal to fall from the roof pressure. The longwall mining of coal did not take a firm hold during the 18009s, and room-and-pillar prevailed. In the early 19009s, steel jacks were introduced, and along with it, the modified caving theory. In March of 1950, a retreat longwall mining system, utilizing a plow, manually operated props, wood cribs and chock releases, was installed in one of Eastern Associated Coal Corp.'s mines.

Jan 1, 1981

By Robert M. Dreyer

During the past two decades, synthetic abrasives have taken over successively greater percentages of the high-grade abrasive market, so that now, with the exception of natural diamonds (discussed in section 3.15.4C of this chapter), the importance of natural high-grade abrasives is negligible. The predominance of synthetic abrasives is indicated in Table 15.4A.1. This shows that the 1968 value of domestically produced synthetic abrasives (excluding synthetic diamonds) was over $80 million, whereas the value of garnet, the largest domestically produced, natural high-grade abrasive, was less -than $2 million. The major synthetic abrasives (other than synthetic diamonds) are: alumina, silicon carbide, boron carbide, tungsten carbide, and metallic oxides, including various iron oxides. A major advantage of synthetic abrasives is that the size and shape of grain can be closely controlled during manufacture. Although Table 15.4A.1 gives the average price of synthetic abrasives, such averages are of somewhat limited value. This is because the actual price varies within wide limits, depending on composition, hardness, size, and shape of grain. In 1968 the approximate total consumption of abrasives in the United States was valued at about $200 million, of which about two-fifths was in the form of synthetic abrasives (other than diamonds), one-third in synthetic diamonds, and the remainder in natural diamonds. Natural abrasive products, such as silica sand, tripoli, and pumice, are important in the low-cost abrasive field. Of the low-cost abrasives, silica sand continues to be the most important, with domestic production of about 300,000 tons at a value of $1.8 million (see Table 15.4A.1). In general, the lower the sales price of the abrasive product, the more limited is the market which can be served from a given production center. Each abrasive has applications for which it is especially useful, but there is a continual struggle among abrasive suppliers to induce substitution of one product for another. Such substitution can be stimulated by changes in method of preparation affecting hardness, shape, and size of grain.

Jan 1, 1976

By Jimmy Bardales

Ante la demanda del uso del concreto para el sostenimiento subterráneo en la industria minera, se buscó alternativas para disminuir el tiempo de fragua y así alcanzar la resistencia requerida antes de continuar la siguiente actividad. En este sentido, el presente texto plantea diseños alternativos donde se reduzca el tiempo de fraguado del concreto lanzado bajo parámetros definidos y así mantener la seguridad, mejorar el ciclo de minado, optimizar los costos de producción y controlar la estabilidad de nuestras excavaciones.

Oct 21, 2015

By N Nosaka

Sinter plants currently have to use many types of ores with different properties due to the great demand for iron ores, which was driven by the massive growth in Chinese iron and steel industry. On the other hand, the development of iron ore mines is limited and the quality of iron ores is in a tendency of deterioration. Therefore, the quick evaluation of iron ores has become more important for a stable sintering operation. In addition to such a background, the CO2 gas emission should be decreased from sinter plants according to the Kyoto Protocol on reduction in greenhouse gases. The present paper first describes the methods for testing the metallurgical properties of iron ores, which use a small volume of sample mainly focusing on magnetite ore that is effective for reducing CO2 and NOx emissions from sinter plants. The sintering properties of ores are evaluated separately according to each stage in sintering process, that is: heating stage before melt formation, primary melt formation in adhering fines layer of pseudo-particles, and assimilation of nucleus ore particle with calcium-ferrite system melts.Next, the application of the tests to the blending ores is introduced showing examples of the studies on the effective usage of the magnetite ores with Marra Mamba type ores.

Jan 1, 2005

By J. W. Koger, R. E. Hurnrnel

QUENCHED, bcc p brass, P1, transforms to a mar-tensitic phase, when it is cooled below room temperature.' This transformation can be followed using resistance measurements since the resistivity of the martensitic phase is considerably larger than that of the parent phase, Fig. 1.' phillips3 first reported that, when Cu-Zn alloys containing between 37.0 and 39.0 wt pct Zn were quenched from the 0 region to room temperature, variable amounts of a phase could be observed depending on the mode of quenching. If the quench occurs very rapidly, the a phase forms by a "massive transformation". The resultant phase has the same composition as the high-temperature P phase from which it was formed. If the quench is less severe, the alloy is retained largely in the p form; however, some a is formed by precipitation. In this case, a contains more copper than the high-temperature 0 phase from which it has formed. The a phase most probably does not undergo a transformation in the temperature range where p transforms to low-temperature martensite. This can be deduced from the Eesistivity-temperature relation which is linear in this temperature range, Fig. 2. The stable a phase which is present along with R. E. HUMMEL is Assistant Professor, Department of Metallurgical and Materials Engineering, University of Florida, Gainesville, Fla. J. W. KOGER, Junior Member AIME, formerly with University of Florida, is now with Oak Ridge National Laboratory, Oak Ridge, Tenn. Manuscript submitted December 13, 1967. IMD.

Jan 1, 1969

By S. Rezaei

Moving ground in the mining industry is almost inevitable; however comprehensive awareness of these movements is necessary to mitigate risk. Monitoring of displacements caused by mining is a key tool for geomechanical risk management. Good monitoring may prevent unexpected failures and protect personnel and equipment. Many displacement monitoring techniques are available, however not all are reliable, accurate, and cost effective. Close range photogrammetry (CRP) is a monitoring method with high accuracy, reliability, and cost effectiveness; and has the ability to measure places that are inaccessible. In CRP, some series of photos are taken in different positions with different angles at different time intervals depending on the displacement rates. These photos are processed using PhotoModeler software and 3D models are made. By comparing 3D models, displacements can be measured. This method has been demonstrated at the Freeport-McMoRan Safford Mine in Arizona. A fault related instability in part of the pit is reactive to mining, and provided an opportunity to compare results between traditional monitoring methods and CRP. In this project, multiple series of photos were taken at different times using a Canon 5D Mark III digital camera, then PhotoModeler software used to make 3D models for each specific measurement event. Movement rates were determined by comparing different 3D models. These results are then compared to results of other monitoring methods to validate the CRP displacement method.

Feb 27, 2013

By Rosmus P

Improper use of auxiliary ven- tilation units during heading operations may often result in the appearance of hazardous methane accumulations. This is the case especially when roadways are ventilated by a combined system with a short sucking pipe at face end performing as the dedusting installation. Uniform air inflow to the face end facilitates sucking off the dust clouds and creates conditions favourable for formation of local methane accumulations. The highest methane concentration occurs in the cutting zone between the rock cut and the pipe inlet, under the roof and by, the sidewalls. Permanent monitoring of methane concentration at face end employs methane sensors. The most important are: one on the road- header's boom behind the cutting head, and one at the air outlet from the dedusting installation.

Jan 1, 1988

By Aitchison J, Clarke G

A reappraisal of the stratigraphy, new regional kinematic analysis and thermobarometric data allow a new interpretation of the metamorphic zoning and tectonic structure of the Upper Eocene high-pressure metamorphic core complex of northern New Caledonia allow a three steps evolution to be proposed : 1) subduction and understacking of previously thinned continental crust elements; 2) subduction blocking due to the crustal thickening; 3) crustal thinning and extensional detachment during the diapir-like uplift and unroofing of the eclogitic core. Steps 2 and 3 may be partly contemporaneous. Such a model accounts for the thermobarometric and radiochronologic data, and also for the weakness of substratum deformation during the emplacement of the ophiolitic nappe.

Jan 1, 1995

By Lawrence K. Nordell

Historical methods of designing steel cord belt splices are compared with modern finite element modeling (FEM) methods. Dependence of the belt strength rating on the splice dynamic fatigue strengths is reviewed. A number of splice schematics are examined, using simple spring theory and FEM methods. Steel cord wire rope design is discussed. The importance of the insulation gum rubber properties and their splice dimensional factors and tolerances are analyzed. Splice fatigue lie analysis procedure is reviewed. This may be used to predict splice life or time of failure, depending on how the conveyor belt is operated.

Jan 1, 1993