Search Documents

By Sowerby BD

The CSIRU Division of Mineral Engineering is developing various techniques for the on-line determination of moisture in coal and coke, and some instruments are now commercially available. These techniques permit accurate and rapid determination of moisture in materials directly on conveyor belts or in bins. The most promising techniques for direct on-belt measurement of moisture in coal are capacitance and microwave transmission. A non-contacting under-belt capacitance and gamma-ray backscatter technique has determined moisture in coal to better than 0.5 wt'/. in field tests at BHP Stockton Borehole Colliery, NSW. Mineral Control Instrumentation Pty Ltd have been licensed to manufacture the capacitance gauges and have installed five commercial units in the coal industry and other industries. Microwave transmission techniques have an advantage over the under-belt capacitance technique in that they are not sensitive to vertical segregation of moisture in coal on the conveyor belt. A laboratory prototype of a microwave transmission gauge has been constructed and tested. Microwave techniques, based on a measurement of attenuation and phase shift, are under development and are expected to be field tested in 1987. These new techniques will enable a wide range of thickness changes to be accommodated. Capacitance and microwave transmission methods are unsuitable for materials of high electrical conductivity, such as coke. CSIRO is therefore developing a fast neutron and gamma-ray transmission technique, which is proving very accurate in laboratory tests. This technique overcomes many of the limitations of thermal neutron moisture gauges and it is expected to be field tested in 1987.

Jan 1, 1987

By Mathew P. J

The CSIRO Division of Mineral and Process Engineering in Melbourne has been developing on-stream analysis sensors based on neutron and gamma radiation for better control of quality and process operations. This has resulted in the development of Ironscan, an on-stream analyser that measures the iron content of both lump and fine iron ore on conveyor belts. It can be mounted under existing conveyors with minimal modifications to the conveyor structure and can cope with steel cables in the belt. An interface gauge and an on-stream coal ash analyser have also been developed, both based on measurement of natural radioactivity. The interface gauge monitors the interface between liquor and mud in thickeners and washers, provided the natural radioactivity of the mud is sufficiently high to detect it above background. The natural-gamma ash gauge is a valuable addition to the Coalscan range of ash gauges. It is applicable to heavily laden coal conveyors or bins where the coal bed thickness exceeds 30 cm, and also to lightly laden conveyors, provided the coal is profiled on the conveyor.

Jan 1, 1991

Buoyant levels of world economic growth and recovery in intensity of metals usage suggest that demand for minerals will remain relatively strong into the 1990's. Supply constraints, low stock to use ratios, financial and political factors imply lower elasticities of supply for minerals in the future. The outlook for minerals and metals prices from a pro-ducers viewpoint is, accordingly, promising.The recent recovery in world minerals prices, following strong growth in the world economy over the last few years, makes it appropriate to consider the structural forces at work in the formation of world demand and supply of minerals. This paper will review past trends and consider some of the main economic issues facing the mining industry in the 1990's.

Jan 1, 1990

By O. P. Chisholm

Dross emerges from the blast furnace either with the lead through a lead well or by tapping from a forehearth or settler, but until a dozen years or so ago few dross reverberatories were used in western lead smelters because it was the usual procedure to circulate the dross from the drossing lead kettles back to the blast furnace. It was quite customary for lead smelters to produce matte in their blast furnaces, as this was the form in which copper could be collected, concentrated if necessary, and shipped to the copper smelters for further treatment. The main prerequisites for good matte formation arc., of course, a more or less definite amount of copper on the charge and sufficient sulphur. Such troublesome impurities as arsenic and antimony were ignored, in so far as possible, although they contaminated the bullion and thereby increased refinery costs. At the same time stocks of blastfurnace speiss containing gold, silver, lead and copper in addition to iron, arsenic and antimony, were being accumulated for want of a market to absorb them. As the dross was being fed back to the furnaces as rapidly as it was being produced, arsenic and antimony tended to build up until the arsenic could effect a combination with copper and iron and an alliance with lead, and the antimony a combination with copper and an alliancc with lead. Sulphur, being the most active agent in taking up the copper, left little of that element for the arsenic and antimony, so that on the whole a somewhat unsatisfactory metallurgy resulted. During this same period, certain lead plants were beginning to encounter trouble with zinc due to the replacement of crude ores of lot zinc content by concentrates containing high percentages of lead and zinc in sulphide form, the blast-furnace slags resulting from the smelting of such concentrates being characterized by a decidedly increased zinc content. It was soon realized that zinc plus sulphur was "poison" to a lead blast furnace and steps were taken to reduce the sulphur content,. At this stage some plants found that any substantial matte fall was out.

Jan 1, 1937

By Edward O’Toole

THe Pocahontas district occupies the extreme southern end of West Virginia, principally McDowell, Mercer and Wyoming counties, and a part of Tazewell county, in southwestern Virginia. The first record of the coal field is a report by Prof. J. P. Lesley, of Pennsylvania, about 1880, in which he mentions a coal opening at the upper end of Abbs Valley, Tazewell county, Va. C. R. Boyd, a mining engineer of Wytheville, Va., published a series of articles in 1881, mentioning coal on Indian Creek, Tazewell county, and on Horse Pen creek, which coals, he stated, extended toward the Ohio River. He also mentions the Abbs Valley coal reported by Lesley. In 1881, F. J. Kimball (who became president of the Norfolk & Western R. R. in 1883)) after examining the Scott mine in Abbs Valley, went northward across Abbs Valley Mountain to the place now known as Pocahontas, where he located what has since been called No. 3 vein of Pocahontas coal. In November, 1882, Jed Hotchkiss and others prepared a cross-section of the Flat Top Mountain coal measures, some notes on which were published by Mr. Hotchkiss, between 1880 and 1892, under the title of " The Virginias.' In May, 1881, the Norfolk & Western R. R. was organized through the purchase of the Atlantic, Mississippi & Ohio R. R., an old line running from Norfolk, Va., to Bristol, Tenn., with branches from Petersburg to City Point and from Glade Springs to Saltville. At that time, charters had been granted for three railroads tributary to the New River Valley, but their proposed routes would indicate that the promoters were concerned with minerals, timber, and a connection with the Chesapeake & Ohio R. R., rather than the development of any coal in the Pocahontas district. One of them was projected to extend up Bluestone River a short distance, but not far enough to reach the coal in the Bluestone Valley, and a little grading was done for a narrow-gage road between New River Station and a point in Giles county, Virginia, near the West Virginia line. All charters and railroads in this district were acquired by the Norfolk & Western R.R.

Jan 1, 1925

By Witkowski A

I have the pleasure to present 6 excellent papers in this section all of major relevance to the mining environment of today where competing social, legal and monetary interests and their often complex interaction require serious consideration. This is particularly true today where huge fluctuations in commodity prices makes mining a perilous undertaking while the world increasingly are becoming aware of the serious threat that mans activities has on his environment. The 6 papers deal with such complex issues as safety in an underground environment; How to protect sensitive wetlands well into the next century; The enormeous waterproblems in China and conflicting dewatering/water supply needs; Disposal of contaminated water in sensitive areas and the dynamic interaction between mining companies and legislation.

Jan 1, 1988

The Kidston breccia pipe is situated approximately 280 km west northwest of Townsville, north Queensland. It is currently Australia's largest gold producer with production varying between 8,000 and 16,000 tonnes of ore per day. Current reserves are estimated at 36.2 million tonnes averaging 1.74 C/t Au and 2.21 g/t Ag. Alluvial gold in the gullies surrounding the deposit was first discovered in the 1880's and between 1907 and 1948 small scale open cut and underground mining was undertaken. Advances in extractive metallurgy and an increase in the gold price were major factors influencing the recent exploration and development of large scale mining of the deposit by Placer Pacific and Kidston Gold Mines. The breccia pipe is trapezoid in shape with surface dimensions of 1100 m by 900 m. Clasts show only limited evidence of mixing during brecciation, with the pre-breccia stratigraphy still discernible on the basis of clast types. This lack of mixing together with the intimate association with intrusive activity, suggests that the brecia formed by collapse, probably associated with the escape of a large volume of irothermal fluid from a crystallising hatholith. Mineralisation and alteration are also sratially and temporally associated with rhyolite emplacement and brecciation. Pre-breccia mineralisation consists of laminated stockwork quartz veins associated with muscovite, quartz and orthoclase-epidote alteration. Stockwork veins contain either anomalous molybdenite or gold. Uneconomic early stage post-breccia mineralisation and alteration consists of cavity infill quartz-epidote and calcite associated with potassic and propylitic alteration respectively. Economic late stage post-breccia cavity infill and sheeted veining consists of quartz-carbonate-sulphide infill associated with phyllic alteration. The grade of gold mineralisation generally decreases downwards in the system with an increase in the amount of pyrrhotite relative to pyrite. Pre-breccia stockwork quartz veins mineralisation is genetically related to the

Jan 1, 1987

By William E. Ford, Edward Salisbury Dana

This section includes one distinct group, the Stibnite Group, to which orpiment is related; the other species included stand alone. Pyr., etc. - In the closed tube melts and gives a dark red liquid when hot and a red- dish yellow solid when cold; in the open tube (if heated ver slow? ) sulphurous fumes, and a white crystalline sublimate of arsenic trioxide. B.B. on ciarcoaTburm with a blue Hame, emitting arsenical and sulphurous odors. Soluble in caustic alkalies. Artif. - Realgar is frequently noted as a sublimation product from furnaces roasting ores of arsenic. Crystals are produced when arsenic sulphide is heated in a sealed tube with a solution of sodium bicarbonate. Obs. - Realgar occurs usually in veins associated with silver and lead ores. It has been found in volcanic regions as a sublimation~duct. It has also been noted as a deposit from hot spring waters. It is often rtasociate wlth orplment. It occurs at Felsi5bBnya, Kapnik and NagyAg, Hungary; Allchar, Macedonia. Binnental, Switzerland, in dolomite. In the United States, at Mercur, Utah; in the Norris Geyser Basin, Yellowstone Park, as a deposition from the hot waters. Found at the Monte Cristo millin district, Snohomish Co., Washington: the namerealga7 is from the Arabic, Rahj af gh&r,powder of the mine. Use. - Was used in fireworks to give a brilliant white light when mixed with saltpeter and ignited. The artificial material is now used for this purpose.

Jan 1, 1922

By W. Spencer Hutchinson

The experiments described in this paper were undertaken primarily for the purpose of measuring the quality of work done in screening and sorting in American concentrating-mills for Prof. Richards' work on Ore-Dressiag. For this purpose a series of samples of screened and sorted products was obtained from four different mills, and a plan was devised for sizing these products, and for tabular and graphic representation of the results. The results, together with discussions as to their significance, so far as they serve to interpret the quality of mill-work, have already been published in the above-mentioned work, and it is not the purpose of this paper to duplicate the work, except so far as is necessary to explain and illustrate methods and appliances. The sizing of coarse products was clone by sifting on screens of sheet-metal with round punched holes. These holes ranged in size from 64 mm. to 0.5 mm. in diameter. Below the smaller limit, punched metal, suitable for this work, was not obtainable, and the sizing was carried on by sifting on woven wire-sieves. The finest woven wire-cloth obtainable gave a hole 0.073 mm. square, and the finest silk bolting-cloth pave a pentagonal hole with an average diameter of 0.069 mm. Even these very fine screens served no useful purpose in sifting certain of the very fine classifier-products, of which all, or nearly all, passed through the finest screen. A new adaptation of a method of settling and decantation with water in beakers was therefore worked out, and by this means the sizing mas carried down to grains of a diameter as small as 0.012 mm. Description of Apparatus and Manipu1ntion.—Sieves of sheet-metal with round punched holes were used as far as practicable, chiefly because, as already explained, the primary object of the experiments was to test mill-work, and the mills had all used

Jan 1, 1905

By Charles H. Foreman, James F. McCarthy

The orebodies of the Hecla mine are from 3 to 40 ft. wide, dip not less than 70°, and in most cases are nearly vertical. The Hecla and Intermediate orebodies are generally associated with a lamprophyric dike, usually about 2 ft. wide, but which attains a maximum width of 7 ft. The ore appears on either or both sides of the dike. The country rock is Burke quartzite with no definite walls and a tendency for nearly horizontal, but irregular, quartz stringers to run from the lode into the walls. This latter condition prevails almost entirely in the hanging wall, causing a natural tendency for portions of the wall to "offset" and resulting in an extremely heavy side pressure. The fact that there are no definite walls causes a great variation in the width of the stopes, as stringers will run into the walls for irregular distances. The ore occurs as galena in varying widths and grades. It is often necessary to mine a face having a " horse"' of waste between two stringers of ore. This block of waste might be 6 or 7 ft. wide but with the Hecla method it is necessary to mine the entire face. In this case an effort is made only to shatter the waste, allowing for easy sorting underground. The Hecla mine requires a flexible system allowing for the extraction of ore from varying widths, with the necessity of close filling to give the needed protection from side weight. About 15' per cent. of the material broken in the face is sorted as waste, either at the face of stope, or in the sorting plant. Shafts, Drifts and Crosscuts The outside dimensions of the shaft are 19 ft. 4 in. by 7 ft. 2 in. The shaft consists of three working compartments, two for the hoisting of ore and one for auxiliary work. The working compartments are 5 ft. 2 in. by 4 ft. 4 in. inside measurement. The rest of the shaft is used for pump column, electric cables, and ladderway. (See Fig. 6 for framing of timbers.) The shaft is about 700 It. from the orebody for topographical reasons. Solid formation was not reached in shaft for 80 ft. Timbers in this section became alternately wet and dry on account of seasonal changes

Jan 1, 1925

By Clift N

Lead concentrate from the Isa and Hilton lead-zinc concentrators of Mount lsa Mines Limited is smelted at Mount Isa to produce a lead-silver bullion. This bullion is cast into four tonne blocks and shipped to Britannia Refined Metals Co Ltd, NorthDeet, England and to plants in Asia for refining and marketing. The traditional treatment stages at Mount lsa are sintering, smelting, and drossing and casting, with some of the sinter plant feed being pre-treated through an Isasmelt plant.A commercial scale lsasmelt based lead smelter was commissioned in early 1991.

Jan 1, 1993

By Henry Hebley

IN preparing this paper it has been the aim of the writer to keep the problems of both producers and consumers in mind. Until now, no attempt has been made to familiarize each group with the other's practice and limitations. This paper is an effort to acquaint the readers with some of the factors pertaining to the problem and cost of mining and preparing steam coal, and also to the economics of producing steam with such coal. In recent years all lines of endeavor have turned to intensive mechani-zation in order to lower the unit cost of production. The average fuel consumption in steam electric generating stations has dropped in 20 years from 4.0 lb. to 1.4.1b. per kilowatt-hour; while the modern power station can generate 1 kw-hr. on a fraction under 1 lb., or 13,000 B.t.u. coal. Also, the amount produced per man has in that same period risen from 3.8 to 8.2 tons, owing to the use of modernized equipment below ground for coal cutting, drilling, shooting, loading, hauling and hoisting. Unfortunately, the rapid speed of 5 tons per minute of operation at which the coal is loaded mechanically precludes any appreciable removal of impurities at the coal face, so that the raw coal is hoisted containing a markedly higher percentage of impurities than the hand-loaded coal, which was subjected to the scrutiny of the miner during loading. Also, during the past 20 years, certain seams of coal lying close to the surface have been made economically available by the improved design of electrically operated shovels and draglines for the removal of overbur-den running as high as 56 ft. This strip coal frequently contains so much ash in the raw state (Table 1) that it would have no sales value. There-fore, coal preparation must be adopted to beneficiate the raw product. Some seams in the United States have a decreasing ash content with decreasing size, owing, in all probability, to the fact that the coal is friable while the impurities are hard, causing a concentration of the low-ash material in the fine sizes. Illinois No. 6 coal being rather hard, naturally the reverse is true.

Jan 1, 1937

By Kendall W. T C

This paper provides a brief overview of the history of the Chaffers Dewatering Project which was successfully commissioned in August 1993. Until the end of 1992 the `Superpit' and the deep mines of the Golden Mile had all been dewatered by a staged pumping system from the 28 level in the Lake View Shaft, which was removed at that time when the Lake View Mine was absorbed into the Superpit. Feasibility analysis had indicated that adaptation of oil industry technology offered the greatest potential for a low cost solution to the problem of dewatering the open pit and deep mines. A KCGM engineer and one of the authors visited the Jackson oilfields to look at the deep well pumping technology in use there in early-1991. In the final analysis a new dewatering station was established in the 23 level crushing station of the Chaffers Shaft using conventional plunger pumps, but the rising main was screwed 178 mm OD (7 inch) casing the suspended from the surface to a depth of 686 metres, and was installed using oilfield personnel and methods. Only the second installation of its kind in Australia, the project achieved the dewatering objective at about half of the capital cost of the more conventional approach and at lower operating costs as well.

Jan 1, 1995

By Whitman E. Brown, Louis J. Erck

The installation in 1948 of a Hum-phrey~ spiral concentrator section at the Hill-Trumbull plant of The Cleve-land-Cliffs Iron Co. is the latest commercial method on the Mesabi Range being used for the recovery of fine iron ore. In two stages of concentration 84 spirals treat approximately 120 long tons per hour of minus ? in. ore. These spirals augment the production of the heavy-density plant which recovers the plus 36 in. iron from the plant crude ore. Structure of the ore is such that, when crushed, about 50 pct of the plant crude is minus ? in. size. After de-sliming in a 66 in. Akins classifier, grinding the classifier product in a ball mill and again desliming in a 78 in. Akins classifier about 15 pct of the crude ore remains to be treated in the spiral plant. Overall recovery of the ball mill feed in the Hill-Trumbull spiral plant during the 1948 season was about 53 pct of the weight and 66 pct of the total iron content. Of the actual feed delivered to the spirals from the 78 in. classifier 64.9 pct of the weight was recovered containing 73.7 pct of the total iron. The average analysis of the spiral concentrate is 55.05 pct Fe and 14.83 pct SiO2. An average of mill assays during the 1948 season is given in Table 1. The Hill-Trumbull plants treat both wash ore and jig-type ore. During the 1948 season spirals were used only on the fine sizes of jig-type ore. At times the deslimed minus ? in. size is of sufficient grade to warrant bypassing the spirals but in the main the fine size is delivered to the 48 first stage spirals and thence to the 36 cleaner or second stage spirals. In the past several years numerous Mesabi Range ores in the fine size cate- gory have been tested by a wide variety of beneficiating equipment. The prodigious amount of research devoted to the recovery of values in the fine ore reflects the dire need of the iron industry to squeeze the last possible unit of iron from the mined ore and to develop suitable equipment and processes to satisfactorily concentrate the leaner horizons as they are encountered in the process of mining. Large governmental and private appropriations have been allotted, new laboratories built, research and technical staffs increased, and operator-manufacturer cooperative agreements applied to hasten the solution of the problem. The University of Minnesota, at its Eighth Annual Mining Symposium in January 1947, dedicated as its objective the bringing to light of technological developments in iron ore beneficiation. Papers were given at that time relating to processes being developed. Specifically, these papers reviewed flotation, Baum jig, selective media concentrator, Hardinge concentrator, Dorrco sizer, heavy media concentration, Hydrotator, and the Humphreys spiral. The Cleveland-Cliffs Iron Co., after encouraging results from tests in a small pilot plant using one full size spiral, made the first commercial installation of Humphreys spirals on the Mesabi Range at their Hill-Trumbull mine, Taconite, Minn. This company

Jan 1, 1950

The Golden Plateau Mine is located at Cracow in central Queensland, 350 kilometres north west of Brisbane. The mine was operated by Golden Plateau NL as an underground mine from 1933 to 1976 with a total production of 18.5 tonnes of gold. Prod

Jan 1, 1994

This Part describes a mine pager phone to public telephone interconnect sys tem that permits mine paging telephones to be selectively interconnected with the public telephone system, as illustrated by Figure 1. This interconnect concept was first conceived and demonstrated in breadboard form by H. E. Parkinson of Industrial Hazards and Communications, PMSRC, as one means for providing improved emergency and off-hours communications. The third-generation prototype unit described in this Part was designed and fabricated by Arthur D. Little, Inc. This unit is a small desk-top or wall-mounted unit that connects directly to both the public telephone line and the mine pager phone line, and requires no modifications to either the public dial telephone or mine pager phones. As part of this task, ADL also built, under a very compressed time schedule, a second-generation prototype unit suitable for reliable demonstration of the interconnect concept during the Bureau's technology transfer seminar on mine communications in March 1973. * A major objective of the design of the third-generation unit described in this Part was that it be compatible with present mine pager phone systems utilizing DC voltage on the mine phone line to activate the phone loudspeakers. Therefore, this unit was designed to operate in a push- to-talk, push-to-listen mode that accommodates the inherent design differences and operation modes of the mine phones of different manufacturers. Though this push- to- talk, push- to-listen mode of operation may seem slightly unusual at first sight, we have found it is easily learned by new users. However, mine phone manufacturers wishing to expand their product lines with such an interconnect system will probably find it to their advantage to customize the design of this system to their particular mine phones, thereby utilizing the unique attributes offered by their individual product lines. This customization should not be difficult, and Section III below suggests some of the features that can be easily added to future designs. Detailed parts lists and circuit schematics for the present third-generation proto- type system can be obtained from the system manual submitted to PMSRC and placed on public file.

Jan 1, 1974

By W. L. Fink, H. C. Stumpf, L. A. Willey

VERY few studies of the aluminum-sodium system have been reported. Heycock and Neville1 were unable to detect any solubility of sodium in liquid aluminum. Mathewson2 prepared an equilibrium diagram consisting of two horizontal lines at the melting points of the two metals. He was unable to detect solubility at either end of the system. Scheuer3 first developed a method for the chemical determination of sodium in aluminum and then studied the solubility of sodium in liquid aluminum. His method involved heating aluminum with excess sodium under hydrogen until the two liquids were at equilibrium, chilling the melt, and analyzing the aluminum-rich layer. He reported the solubility to be 0.l0 pct sodium at 700°C, 0.115 pct at 750°C, and 0.128 pct at 800°C. This paper on the aluminum-sodium system is the twenty-first in a series from the Aluminum Research Laboratories describing equilibrium relations in aluminum alloy systems. MATERIALS The alloys for this investigation were prepared from electrolytically refined aluminum (99.99 pct) and sodium of reagent quality conforming to specifications of the American Chemical Society.4 Chemical analysis of the aluminum showed the following impurities: 0.002 pct Si, 0.002 pct Fe, 0.002 pct Cu, <0.001 pct Mn, 0.002 pct Mg and 0.001 pct Na. The sodium content of all alloys was determined by either chemical or spectrographic standard procedures5 No. IIA and No. SII respectively. DETERMINATION OF LIQUIDUS The boundary of the miscibility gap was determined by a modification of the method of Scheuer3 and of that used by Henry and Cordiano.6 As finally developed the method was as follows: A fused alumina crucible 25 mm id with 75 mm depth and 1.5 mm wall thickness was placed on the bottom of a container made from a 4-in. length of 1 ½ -in. iron pipe and pipe caps. The space around the sides of the crucible was filled with 40 mesh crystalline alundum. A charge of 60 g of aluminum and 10 to 15 g of sodium was placed in the crucible, the sodium first being trimmed and rinsed with iso-pentane to remove kerosene. The container was tightly capped, filled with argon (99.6 pct pure), and heated to the desired temperature (between 670 and 800°C). A positive pressure of argon (about 8 mm of mercury) was maintained through a small pipe to the upper cap. After soaking for from 2 to 5 hr, the container was quenched by directing a stream of water onto the base, so that solidification of the aluminum-rich layer was rapid and essentially unidirectional. Analyses were made on drillings taken from the bottom of the ingots after machining off the surface layers. Pre-

Jan 1, 1948

By H. B. Smith, B. Egeberg

Britannia metal is a white alloy consisting primarily of tin and antimony, the tin greatly predominating. The alloy usually contains a small amount of copper and occasionally very small amounts of one or two other metals, such as bismuth, zinc, and lead. It is capable of being cold-rolled, it takes a high polish, and it is fairly noncorrosive; properties which make it a popular metal for many household and traveling utensils. Britannia metal is similar in many respects to pewter and has largely replaced pewter in the arts, but it should not be confused with that alloy, because pewter is essentially a tin-lead alloy, while Britannia is a tin-antimony alloy. In view of the fact that so little has been published concerning Britannia metal, the authors feel justified in presenting the results of their investigation, particularly since the behavior of this alloy under cold rolling and heat treatment differs so greatly from that of other metals and alloys. The old craftsman, engaged in the making of ornaments or tableware, heated the cold-rolled sheet metal or his finished product to a straw color corresponding to about 375" I?., claiming to produce thereby a harder and more rigid article. The fact that possibly led him to this heating was that a reheated article or sheet made from Britannia metal has a distinct metallic ring when struck a sharp blow, whereas an unheated article or sheet has a leady, dead note. No doubt he has associated the metallic ring with a greater rigidity and strength, and justly so, as will be seen later. The approximate analysis of the metal we investigated was 91 Sn, 7 Sb, 2 Cu, and the molten metal was bottom-poured into an iron mold yielding an ingot 7 3/4 in. wide by 11 in. long and % in. thick, the casting temperature being 800" F. The ingot was cold-rolled to a sheet 0.032 in. thick, sufficiently large samples for experimental purposes being cut from the sheet at intermediate stages. The samples were all tested for hardness with scleroscope and Brine11 machine, then heated to 212" F. for 30 min., and again tested after cooling to room temperature. The same samples were heated successively at 300°, 400°, and 440" F., followed

Jan 1, 1929

By David B. Cook, James R. Bieke

I. INTRODUCTION Lawyers are a cautious breed; and it might be expected that a paper concerning a broad and complex area of legal regulation, prepared by lawyers for presentation to a predominantly non-legal audience, would commence with several caveats. Ours are the following: First, we have written a broad (and, in some instances, simplified) overview of the regulatory system and of some of the more important requirements generally applicable to uranium mine and mill wastes in the United States. Our paper is not a legal opinion setting forth all of the governmental requirements that would have to be met by any particular mine or mill. Similarly, we do not imply that the requirements we mention are necessarily applicable to each and every mine and mill in the country; depending on the facts, some of the requirements may be inapplicable or avoidable through exemption or variance proceedings. Compliance decisions and strategies for particular facilities must be considered on a site-specific basis. Second, we have undertaken merely to describe the regulatory framework and some of the generally "applicable" requirements which have been promulgated and proposed by administrative agencies. We express no opinion on whether, under the U.S. Constitution and statutes, the existing and proposed agency regulations are valid in general or as applied to any particular mining or milling operation. There are, of course, procedures for judicial review of agency action; and newly promulgated environmental regulations have frequently been challenged, with varying degrees of success, before the courts. For us even to begin to consider such issues would expand an already forbiddingly long paper to totally unmanageable proportions. Third, in light of the subject of this Conference we have limited our paper to the legal framework and requirements applicable to uranium mine and mill "wastes" -- primarily mine overburden and waste rock and mill tailings (including waste tailings solution). We treat operating discharges (e.g., emissions from yellowcake drying) only peripherally. Fourth and finally, it is important to note that this paper, at least in so far as it concerns the specific requirements of particular regulations, will likely soon be out of date in some important respects. Despite

Jan 1, 1980

By Pate W. T

This paper describes the development of a dynamic flowsheet simulator for comminution operations. Object oriented software design allows the handling of multiple ore types, blended into multicomponent feed streams. Software objects have been c

Jan 1, 1998