Search Documents

By John C. Loretto

"The paper identifies two of the main problems encountered in recent hydrometallurgical plants for the recovery of gold and silver: firstly, the plant recovery is lower than anticipated from the testwork; secondly, the metallurgical accounting figures cannot be reconciled.The principal reasons for the plant recovery being lower than the testwork are discussed, together with solutions that can minimize these problems both during the design stage and during the plant operation after the problems have manifest themselves.The reasons for the difficulties in metallurgical accounting are analyzed by reviewing the various components of the plant figures. Recommended solutions are given for minimizing this problem and the realities of obtaining accurate figures are discussed.IntroductionThe start-up over the last few years of new hydrometallurgical plants for the recovery of gold and silver has brought to the surface again a number of problems. Most of the problems have existed for some time and they manifest themselves mainly in two ways. Firstly, the plant results do not agree with the metallurgical testwork figures; secondly, the metallurgical accounting figures do not balance.Metallurgical TestworkThe plant results not agreeing with testwork figures are mainly due to:a) testwork samples not representative of the eventual plant feed;b) misinterpretation or misunderstanding of testwork ;c) plant losses;d) plant design not allowing testwork results to be achieved;e) operating deficiencies."

Jan 1, 1982

By D Kepert, C Simpson, D Edwards

Channel iron deposits (CID) currently supply over 40 per cent of the seaborne iron ore trade out of the Hamersley Province. The two well documented producing systems (Robe and Marillana palaeochannels) were both discovered during early reconnaissance mapping principally by BHP Billiton (BHPB) and Geological Survey of Western Australia (GSWA) during the mid 1950s to early 1960s. Both crop out extensively over the majority of their length. Hot on the heels of Fortescue Metals Group 2004 - 2005 discovery of approximately 2.6 billion tonnes (Bt) of undercover iron ore mineralisation in the Chichester Range, the Fortescue Exploration Department turned its attention elsewhere throughout the Hamersley Province. Reappraisal and analysis of publicly available data and ground truthing of developing models led to the recognition of the Solomon palaeochannel system. Subsequent exploration defined a world-class Resource of some 1.9 Bt of iron ore mineralisation of which the great majority is buried CID. Apart from the Marillana CID system, the Solomon region is the only major CID with significant tonnes of sub two per cent alumina CID with over 500 Mt delineated to date. Exploration has also outlined significant supergene bedded and detrital iron ore mineralisation. Ongoing drilling is expected to increase the resource base both in terms of tonnes and confidence. This paper outlines the principal contributing factors which led to the discovery of the Solomon CID and compares its geology with the Robe and Marillana palaeochannel systems.

Jan 1, 2009

By M. B. Mirza, F. D. Wright

Models of photoelastic material were made to simulate a mine roof that had cracked over the edge of the pillars and at the center of the span. Models were restrained from moving laterally outward so they acted as flat arches. Uniform loading was approximated by loading the models along the bottom at eight points spaced equally along the span. It was found that for models with depth to span ratios of 1:3 to 1:6, the maximum stress at the top of the center crack could be calculated directly by the following formula: Elastic stresses in mine roofs composed of sedimentary beds are usually computed by assuming that the immediate roof bed acts as a fully restrained beam uniformly loaded by its own weight and by overlying strata. Very little work has been done to analyze stresses in roof beds or beams which contain vertical (normal to the span) or nearly vertical cracks. Yet every mining engineer has walked safely under roofs that show such cracks. As far back as 1933, Bucky' made model studies of the effect of vertical cracks on the behavior of horizontal strata. He did not make any analysis of the stresses but did show that a cracked beam will stand safely under certain conditions, and also showed that a beam restrained at the ends can crack over the supports and in the middle without collapsing as long as the ends of the beam are not free to move laterally outward. The beam, or rather, part of the beam, acts like a flat arch and supports itself by pushing outward at its supports. In 1941 Evans2 treated analytically the problem of a beam cracked along so many planes perpendicular to the axis of the beam that no tensile stress can operate. He named this type of beam a "voussoir-beam" by analogy to the voussoir-arch. In 1962 ~a~cocks~ modified Evans's solution by including the effect of the shear stress component of the resultant force at the abutment. This paper gives the results of a photoelastic study of the stresses in a beam containing vertical cracks in the center of the span and over the supports. A

Jan 1, 1963

By A. L. Wilder

Coeur d'Alene Mines Corporation's newest precious metals property is located in the old Rochester Mining District approximately twenty-five miles northeast of Lovelock, Nevada. Built at an elevation in excess of 6 000 feet, the Coeur-Rochester gold silver heap leach property encountered cold weather operational problems typical of most northern Nevada heap leach properties, soon after the start-up of operations last fall. Due to the size of the heap area under leach at Rochester, it was decided that 1 the usual practice of spraying to an "ice field" and waiting for the spring thaw was impractical. Further, the delivery schedule for a solution heating system of the size required was unacceptable. Accordingly, Rochester personnel embarked on a program to seek out a leach solution distribution system that would enable an operation through the winter and yet be cost effective. The findings of this program were rather dramatic and, as a result, the whole perception of heap leach solution application at Rochester has changed forever.

Jan 1, 1988

By F. A. Schaufelberger

Early work on chemical precipitation of metals from metal salt solutions is reviewed. The chemistry and thermodynamics of precipitating copper, nickel, cobalt, and cadmium metals by reaction with hydrogen are discussed. Mechanisms of metal precipitation, nu-cleation, growth, and agglomeration are reviewed, as well as some solubility phenomena of cleation,gases and solids at elevated temperatures. Experimental data presented deal mainly with the reaction of copper sulfate solution with Hz. METAL can be recovered from a leach solution either indirectly by precipitation as a compound that is later reduced or directly by electrolysis, cementation, or chemical reduction, for example, with hydrogen. The widely used electrowinning processes suffer from the inefficiency of converting fuel to low voltage dc and from low current efficiency when complete recovery is attempted. With the batch hydrogen reduction methods outlined here, a unit of fuel converted to hydrogen in modern gas reform plants will make two to three times as much metal as can be obtained with electrolysis. With continuous hydrogen reduction, four to six times as much metal is obtained. Precipitation by reducing a metal salt solution with H, has been known for almost 100 years.' Commercial use of the process, however, awaited the research and development program initiated by Chemical Construction Corp. Within the last few years this program has brought about construction of commercial plants, listed on p. 701. Ideal hydrogen reduction will precipitate a pure metal from a solution obtained by commercial leaching methods at a rapid rate without excessive temperatures and pressures. The metal precipitate will be of desired size and density, less than a percent left in the vessel being deposited on the wetted parts. The present discussion will outline Chemical Construction Corp.'s early development program and will discuss the chemistry and mechanics of reducing copper, nickel, cobalt, and cadmium from solution by H2. Work on selective reduction of nickel from cobalt has been described earlier.2 The article is not concerned with precipitation of copper by disproportionation of cuprous solutions where yield is limited" to 50 pet.* It does not discuss use of gaseous reducing agents other than hydrogen, such as SCV which may lead to contamination with sulfur, or CO," which is considerably more expensive than hydrogen and produces a gaseous reaction product, CO2.† The article does not include use of other nongaseous reducing agents: which are far more expensive than CO. Also, notes on the history, engineering design, and performance of commercial plants have been given elsewhere." It will be shown that a pure metal can be precipitated by reduction with hydrogen from solutions obtained by commercial leaching methods when the solution cohposition is controlled and proper acidity, proper metal ion concentration through controlled complex formation and hydrolysis, and adequate agitation for suspension of metal and for transfer of reducing gas are maintained. Reasonable temperatures and pressures are used which are less excessive than those used by previous workers, although they are maintained at above equilibrium values because of process kinetics.' It has also been found necessary to induce nuclea-tion and to control growth and agglomeration in order to get a powder product of suitable physical properties. Review of the Literature Muller, Schlecht, and Schubardt of I. G. Farbenm claimed a successive reduction of silver, copper, nickel, cobalt, and zinc from ammoniacal solution by applying progressively higher temperatures and hydrogen pressures. Metals produced by this technique were not pure, since no attempt was made to adjust the solution composition between the different reductions. It is doubtful that the zinc product contained any metallic zinc. The major contribution to the literature" was made by the Ipatiews,12 who prepared platinum, iridium, copper, nickel, cobalt, lead, tin, arsenic. antimony, and bismuth at often extreme conditions, up to the critical temperature of water (373"C), at 1500 to 7500 psi, for as long as several days. Even cadmium and zinc were claimed to have been observed in trace quantities precipitated together with basic salts. In the early experiments solutions were not stirred. Extensive formation of oxides and basic salts occurred. probably long before sufficient hydrogen could be supplied in the unstirred liquid to decrease the metal concentration in solution by reduction. The importance of hydrogen pressure was

Jan 1, 1957

By P. Henning

Rock fall accidents continue to be the main cause of fatal and serious injuries in the mining industry. Although there has been an improvement in the FOG (falls of ground) related fatal and serious injuries over the past few years, the rate is still too high. New technology has made it possible to reduce this rate significantly. FOG accidents imply failure of the support system or the design of the support system in use. In this paper we deal with the latest technology available to assist the mines to reduce the rates of FOG related injuries and fatalities.

Jan 1, 2010

By Mary S. Esfandiary

This list of organizations that conduct research and development programs on coal has been compiled by the Bureau of Mines with the thought that such a directory may provide a useful guide to worldwide research efforts in the areas designated and may facilitate communication between organizations with similar interests. This list includes government, university, private, and commercial organizations. Many of these groups are conducting comparatively modest but often particularly interesting or specialized investigations. The areas of investigation have been defined in a broad manner--these include analysis and constitution, mining and geology, preparation, combustion, briquetting, high- and low-temperature carbonization, gasification, hydrogenation, Fischer-Tropsch, and health and safety. In some instances such information is not available, but the names of the organizations themselves often indicate immediate arias of interest. Special publications issued by and describing the work of each organization have been cited, when known; almost all of the organizations also publish results of their investigations in the technical press. Several foreign technical and trade publications that include such information and are not published directly by any of the organizations listed are cited in the pages following the list of organizations in each country. This list is not complete. Information that would improve coverage and/or accuracy will be welcomed by the Bureau of Mines.

Jan 1, 1961

By Daniel D. M. Adams

In 2004, Rio Tinto started a major project to implement Mine Monitoring and Control (MMC) systems worldwide. A detailed selection processes was undertaken and migration to a standard system was started. Today systems are operating around the world and serve as the core of to many business processes. Implementations include highly union areas, large mines, centrally managed mines, and remote areas. Each implementation has unique challenges but all are working towards the common goal with common systems. This paper reviews two projects that Rio Tinto has deployed in diverse conditions. The projects are the Rossing Uranium upgrade from the original Wenco system to the common standard and Iron Ore of Canada?s general technology upgrade. Also discussed is the future of mining at Rio Tinto, specifically the drill automation projects, and how it is utilizing the common standard MMC systems.

May 1, 2010

By Charles W. Dickson

CONTENTS. [ ] I.THE RELATION OF NICKEL TO PYRRHOTITE. Introduction. The Sudbury district is to-day one of the two great sources of nickel in the world. The peculiar geological relations of

Jan 1, 1913

By Ali M. Ghazi, Ronald J. Goble, Lowell S. Whiteside

"Geerite (Cu1.6S) is a rhombohedral copper sulphide which occurs naturally in epitactic replacement of sphalerite; cell dimensions closely approximate those of the host sphalerite.Geerite-type structures can be produced by leaching digenite (Cu1.8S) in ferric sulphate solutions. X -ray diffract ion and electron microprobe studies indicate that eight metastable geeritetype structures can be produced, depending upon the concentration of f erric sulphate solution used and the duration of the each. Although compositions cluster on or near values observed for natural phases, optical properties indicate that we are dealing with polymorphs of these phases. Leaching of chalcocite (CU2Sj in dilute f erric sulphate solutions produces similar results. In contrast, leaching of chalcocite in more concentrated solutions seems to produce true analogues of natural minerals.During froth flotation, sphalerite is activated with a monolayer of floatable copper sulphide with the composition, CuS, of the mineral covellite. However, covellite is not significantly more floatable than sphalerite, and has an incompatible structure because of the presence of covalently-bonded atoms of sulphur. Leaching ofdigenite was used to produce a polymorph of covellite with a geerite-type structure, compatible with that of sphalerite. This polymorph has a flotational behaviour similar to copper-activated sphalerite, suggesting that the monolayer has a geerite-type CuS structure. IntroductionIn an ideal close-packed sulphide structure the distance between sulphur layers, D, is equal to 2R 2/3, where R is the radius of the sulphur atoms. In sulphides with covalently-bonded sulphur layers, such as covellite (Fig. I), D will be an average of the number of covalentl y-bonded and close-packed sulphur layers, weighted as to the relative number of each type of layer. Both D and R are spacings which are readily identifiable structurally and on X-ray diffraction patterns. Goblel has shown that for copper-iron sulphides with metal-to-sulphur ratios between 0 and 2 and copper-to-total metal ratio s between 113 and I there are strong correlations between composition and measured D and R distances (Fig. 2). D can be represented by a single empirical equation relating interlayer spacing to composition; R must be represented by three equations relating the radius of sulphur atoms to composition. One of these equations (R, in Fig. 2) represents ideal close-packed behaviour, the other two represent sulphur radii greater than (R1) or less than (Rh) the ideal."

Jan 1, 1988

By E. T. Turkdogan, M. T. Hepworth, R. P. Smith

The permeability of oxygen in 0 iron in the tempera-ture range 700" to 900 C and in 6 iron at 1450°C was determined by the rate of internal oxidation of iron, containing -0.1 pct Al. The solubility of oxygen in zone-refined iron was determined by equilibration with hydrogen-water vapor gas mixtures at 1450" and 1510°C; oxygen solubilities , for iron in equi1ibriu.rn with molten oxide, are found to be 66 and 83 ppm for these two temperatures, respectively. The diffusivity of oxygen in iron at 14500C3 as calculated from the permeability and solubility data, is (4.1 * 0.6) x 10 "B sq cm per sec. OXYGEN is one of the most common impurities present in iron or steel, mainly in the form of oxide inclusions. In the study of many metallurgical problems concerning solid iron, it is often desirable to know with a reasonable accuracy the solubility and diffusivity of oxygen over a wide temperature range. The solubility of oxygen in solid iron has been the subject of numerous studies yielding highly discordant results as seen for example from the literature surveys made by Meijering &apos; and Schenck et a1.&apos; As shown by Kitchener et aL3 and by Sifferlen, the high oxygen solubilities reported by many investigators are the result of oxidizable impurities which are often present in iron. In addition, there have been experimental problems associated with icaccuracy of oxygen analysis of iron containing less than 100 ppm 0. A number of studies have been made on the permeability of oxygen in a and y iron using Fe-Si, Fe-Mn, and Fe-A1 alloys in the internal-oxidation experiments.1&apos;2&apos;5&apos;6 However, no direct measurements have been made of the diffusivity of oxygen in iron. In the present work two sets of experimental measurements were made: permeability and solubility studies at 1450" and 1510°C and permeability studies only in the range 700 to 900°C. In both sets of permeability measurements slab-shaped specimens containing small predetermined amounts of aluminum in solution were exposed at constant temperature to gas mixtures of hydrogen, water vapor, and argon for varying times. These specimens were quenched, sectioned, and examined for oxygen penetration by metallographic observation of aluminum oxide particles which formed. From these data, it is possible to calculate the ratio of the diffusivity of oxygen in iron, D, to the equilibrium constant K for the reaction Hz(g) * O (dissolved in iron) = H,O(g). EXPERIMENTAL Permeability Measurements at 1450°C. An ingot of vacuum-carbon deoxidized iron containing 0.086 pct A1 was prepared, using commercial "Type lO4A Plas-tiron"; after hot rolling, specimens were machined into slabs a by 2 by 2 in. The impurity contents were: S, P < 0.002 pct; C, Mn < 0.01 pct; each of all other Usual impurities < 0.004 pet. The amount of oxide inclusions in this material, determined by a bromine-methyl acetate extraction, corresponded to about 20 ppm 0 in the iron which agreed well with the results of vacuum-fusion analysis. Each specimen was annealed at 1450°C for 1 hr in purified hydrogen, polished to a smooth surface, and then introduced into a controlled oxidizing atmosphere in a recrystallized alumina tube at 1450°C. The constant temperature zone (*3"C) was about 3 in. in length. The gas composition was controlled by mixing argon with hydrogen (using calibrated constant-head flow meters) and passing the mixture through a column of a mixture of oxalic acid dihydrate and 10 pct anhydrous oxalic acid, to establish a required water-vapor content in the gas mixture. The temperature of the oxalic acid dihydrate column was controlled by a thermostat. The total gas flow was in the range 800 to 1000 cu cm per min. The exit gas from the reaction tube was passed through a weighing bottle containing a desiccant, to cross-check the degree of water-vapor saturation, which for all experiments was about 97 pct of those derived from the data of Baxter and Lansing.1 For a typical experiment, a specimen was introduced into the furnace in a stream of dry argon and hydrogen. The specimen was then rapidly raised by a Pt-Rh alloy wire into the hot zone and allowed to reach the reaction temperature, at which time the oxidizing gas mixture was introduced. The oxygen potentials employed were sufficient to oxidize aluminum but not to cause liquid iron oxide to form. After a specified time, the experiment was ended by dropping the specimen onto a water-cooled copper block at the bottom of the reaction tube. The depth of the internally oxidized zone, hereafter called the "case", was determined by sectioning the specimen at right angles to the long direction. The section was then examined under a microscope equipped with a micrometer stage. In general, the oxide particles were fairly uniform in size and distribution, forming a reasonably well-defined interface between the oxidized and unoxidized region. A typical cross section as observed at X30 is shown in Fig. 1. A thermal macroetch was used in one selected specimen to delineate the case. A cross section of a previously oxidized slab was polished and reheated at 1450°C in a hydrogen atmosphere for about 10 min. Upon quenching, the surface relief shown in Fig. 2 was produced; causes of this effect are unknown. Permeability Measurements Below 900°C. A slightly

Jan 1, 1967

"A 3-dimensional finite element model for stress/stability analysis of rock excavations in underground mines is presented. Developed for use on personal computer under OS/2 operating system, the model employs the 8-node isoparametric brick element and accounts for such loading conditions as in situ stresses and gravity loading of the rock mass. In addition, modelling of backfill in mine stopes as in situ stress-free material is incorporated. Material failure is assessed by Mohr-Coulomb or Hoek-Brown failure criterion. A mine design example is presented to illustrate the potential use of the model as a tool for stope design.IntroductionNumerical modelling of mine structures has become a vital tool for mine design in recent years. The need to maximize ore extraction ratio and to reach deeper mineral deposits underground has led the mining industry to employ numerical methods of analysis to undertake complex ground control studies in order to better understand the ground response to mining excavations and to evaluate the ground support requirements. Thanks to the rapid developments in computer technology, it is now possible to perform very comprehensive analyses including, but not limited to, 3-dimensional, elasto-plastic, or large deformation or time dependent nonlinear analyses on personal computer.During the past ten years or so, many researchers undertook 3-D finite element analyses of rock mechanics problems in mining engineering. The following is only a sample review. For example, Chan&apos;!&apos; used three-dimensional finite elements to study the mechanical response of jointed granite during shaft sinking at the Canadian Underground Research Laboratory. Wang et al.(2) performed 2-D and 3-D finite element analyses of room-and-pillar mining system with flat and rolling coal seams. Thatejatu used three-dimensional finite element method to examine the problem of branching tunnels. Dolezalovaw used three-dimensional finite elements for the analysis of tunnel-face advance with partial excavation as well as full-face excavation in combination with rein for cement of the face by long anchors. Peili (5) used three-dimensional finite elements for the simulation of rock-liner interaction near the tunnel face."

Jan 1, 1992

By Phillip A. Armstrong, Charles A. Lewinsohn, John H. Gordon

"This paper describes the opportunity offered by employing systems based on mixed conductive ceramics, in particular, ceramics conductive to oxygen ions and electrons, in reducing CO2 emissions from metallurgical production. Membranes based on these mixed conducting properties enable commercial viability of several attractive metallurgical processes. One of these processes utilizes modular, ceramic-membrane structures for the generation of pure oxygen, in tonnage quantity. The membrane-based systems offer significant capital savings and operating efficiencies in various metallurgical processes. The current status of this technology is summarized below.IntroductionCryogenic oxygen supply technology is currently the state-of-the-art for applications that require large quantities of oxygen (hundreds to thousands of tons per day). Cryogenic technology, however, requires substantial energy inputs and, hence, adds significant costs and emissions to processes. Furthermore, cryogenic oxygen supply technology is mature and there is relatively little potential for substantial capital cost reduction or efficiency improvement in coming decades. Non-cryogenic technologies offer a means to reduce the environmental footprint and cost of the oxygen supply facility in various applications.Ion Transport membranesCommercially available non-cryogenic air separation technologies, such as adsorption-based and polymeric membrane-based methods, do not afford the economies of scale that the cryogenic distillation enjoys. Therefore, industrial gas industry researchers began searching for alternatives to the relatively inactive and unselective polymeric membrane materials available. In the late 1980’s, Air Products began developing a new class of highly selective membrane materials with exceptionally high activity for oxygen transport. The materials constitute a class of oxide ceramics, and conduct both oxygen (as oxygen ions) and electrons in the same membrane, separating oxygen from air electrochemically. Numerous detailed process economics studies have shown that, based on these ion-transport membranes (ITM’s), the cost of oxygen can be reduced by approximately one-third relative to that obtained from state-of-the-art cryogenic oxygen supply technology, through a combination of capital cost savings and efficiency improvements. [1,2,3]"

Jan 1, 2008

By A. Perry Thompson

I. GENERAL DISTRIBUTIONS APPEARANCE, AND RELATIONS MINING in Butte has seldom encountered covellite in commercial quantities. The notable occurrences, extending vertically and laterally perhaps several hundred feet, presented scattered, bladed lenses of this mineral in a matrix of quartz, pyrite, enargite, bornite, and chalcocite. But under the microscope covellite is seen to be widespread in the Butte ores, though in such small quantity that megascopic examination will not discover it. In early mining operations covellite was found in the Gray Rock vein, a member of the Blue vein system. As described by Sales,1 it persisted as an occasional ore mineral, associated with quartz, pyrite, tetrahedrite, bornite, chalcocite, and minor amounts of sphalerite, from the 700-ft. to the 1,200-ft. level of the East Gray Rock and Diamond mines. Crushed quartz-monzonite and later quartz completed the vein filling between

Jan 4, 1915

Goodenough and Fergusson Islands, in eastern PapuaNew Guinea, lie in an area of crustal extension on the western end of the Woodlark Basin seafloor spreading system. The islands are made up of a number of mountainous domes of complexely deformed basement, and these are intruded by large bodies of granodiorite. The domes are bounded by curved shear zones and faults dipping outwards at angles of around 25 to 45¦. The cores of the domes contain lower crustal rocks of eclogite and granulite facies, these rocks have undergone retrograde metamorphism in the outer sheared zones. Movement indicators on the shear zones indicate a complex moverm.-It geometry which does not fit the models proposed by earlier workers. These dome-like structures are similar to the metamorphic core complexes of the western United States Cordilleran region, however there are a number of aspects which do not fit with the models proposed for the development of metamorphic core complexes. Uplift of the metamorphic basement probably resulted from a combination of forces associated with the extension of the crust and the intrusion and emplacement of granodiorite plutons.

Jan 1, 1990

The Bau Goldfield lies in the southwestern corner of Sarawak in East Malaysia. Evidence of past mining in the form of open pits and adits can be found over an area of 250 sq kin, centred on the township of Bau. Chinese were mining gold in the district as early as 1820. The Bau Goldfield so far has produced approximately two million ounces of gold, from alluvial deposits and over 50 hard rock mines. The largest single producer was the Tai Parit mine (700 000 oz) which was operated by the Borneo Company from 1898 to 1921 and by a local Malaysian family from 1991 to early-1997. Over the past ten years, gold resources totalling around one nullion ounces have been delineated through systematic exploration using modern techniques, with the bulk of the resource hosted in two deposits (Jugan and Pejiru).Triassic to Jurassic andesitic volcanics and coeval intrusives are the oldest rocks that crop out in the Bau Goldfield. These igneous basement rocks are unconformably overlain by 500 m of late Jurassic, massive, micritic limestone which in turn is overlain by a 1500 in thick flysch sequence, composed mainly of shale. Basement rocks and limestone are exposed along the hinge of a ENE-striking anticline that passes through the Bau district (Bau Anticline). A NNE-striking belt of Miocene granodiorite porphyry stocks and dykes also passes through the Bau Goldfield. All of the known gold deposits lie within 5 km of this zone of intnisives, with a concentration of deposits at the intersection of the intrusive hell with the Rau Anticline.

Jan 1, 1997

By J .. R. Brown, G. Deschenes

X-ray Photoelectron Spectroscopy (XPS), X-ray Diffraction (XRD) and Electron Probe Micro-Analysis (EPMA) were used to characterize chemically the gold complex adsorbed on activatedcarbon from a solution containing 102mglL Au and 0.5 giL thiourea. This paper also considers the gold chloride and the gold cyanide systems. The results indicate gold is adsorbed on activated carbon from the thiourea solution as the gold (I) thiourea complex, i.e. Au [CS (NH) 2];&apos; Other gold species such as metallic gold were not detected on the carbon support. These results also suggest the elution of the gold (I) thiourea complex can be performed with high recovery.

Jan 1, 1993

of our good friends and fellow members: William D. Brennan Charles Beuchat who left the world better for their having lived in it.

Jan 1, 1931

By Michael W. Oakland

Weidlinger Associates was retained to evaluate the foundations supporting ten oil storage tanks at a tank farm on the east coast. The tanks were constructed over the site of a landfill which was underlain by deep organic deposits. The tanks were typically 48 ft. in height and ranged in diameter from 60 to 150 ft. The tanks were supported on both wood and steel pipe piles. After more than 35 years of service, an inspection found that up to 25 percent of the piles had separated from the mat foundation. The operations at the facility were temporarily stopped pending further investigation. Weidlinger developed comprehensive finite element models of the foundations for each tank and used random generators to conduct Monte Carlo simulations the range of scenarios of detached support conditions since it was not possible to survey all the piles below the tanks. To confirm the modeled performance and verify stability, each tank was also load tested using water with electronic instrumentation installed by Geo-Instruments. The instrumentation provided real time, web based monitoring during testing in areas which would otherwise be inaccessible during loading. Through inspection, complex modeling and sophisticated load testing, Weidlinger and Geo-Instruments were able to show that all but one of the tanks could safely be put back into service. This paper details the analysis, Monte Carlo simulations and instrumentation and load testing performed for this unique project.

Jan 1, 2009

[ ] DISCUSSION F A LORIA*-The method of testing gun steel for resistance to surface cracking described in this paper was restricted to the examination of small, rod-shaped specimens The writer would like to point out the importance of other factors in producing defects in forged and bored gun tubes which would not be apparent in this investigation because of the nature of )he test Actual section size would accentuate the possibility of internal wall (bore) defects arising from unequal expansion between the internal and external wall surfaces on firing, resulting in internal tearing Checks and tears on the inside walls arise from internal tensions and nonuniformity on cooling, but the internal tearing can be reduced by using alloys of low expansion and of good thermal conductivity so as to reduce the difference between the outer and inner wall surfaces Also, the possibility of the location of inclusion segregates within a machined gun tube becomes more likely than in a small test specimen The effect of these nonmetallics on gun life and performance is evident when one realizes that the inclusions are soft yet brittle They reduce the amount of plastic deformation which can take place before cohesive failure occurs Once localized fracture has occurred at the position of a chain of these inclusions, a sharp notch (crack) is formed which produces stress conditions more favorable to cohesive failure than to plastic deformation These cracks aid erosion by providing channelways for the explosive gases, eventually leading to the tearing out or spalling of blocks of metal Oxidation of the surface may be partly responsible for the change in the surface of gun steel during firing observed by the author The appearance of burn on the surface is an indication that high temperatures were reached on firing, resulting in a slight oxidation of the surface Since the color of the oxidized film depends on both temperature and time, a higher temperature is required for a given color to form when it is caused by explosive heat, which acts for only an extremely short time at a given spot, than when it is caused by ordinary tempering The cross section of the gun steel specimen, Fig 16, illustrates that the repeated firing temperatures were high enough to cause

Jan 1, 1948