Search Documents

By W. W. Odell

"It has long been recognized that coke is a more desirable fuel than bituminous coal in water-gas apparatus of present design, but still considerable headway has been made in the use of the latter fuel as a substiaute for coke. This is particularly true in the Central States where the supply of high-grade coke has been very limited and uncertain during the past few years, and where coking coals of low sulphur content were available in quan¬tities. In fact, with, the present difference in price of coal and coke, it is possible to realize a marked saving when using a coking bituminous coal as generator fuel.Difficulties have been encountered in the use of such fuel, but they have, to a large extent, been overcome. One of the chief obstacles in the use of the more general utilization of bituminous coal for water-gas manufacture, is the fact that, with normal operation, the capacity per unit of time is reduced. This of course is a serious problem for plants operat¬ing at capacity with coke fuel. However, this difficulty can, to a large extent, be remedied by a changed method of operating, and can be entirely remedied by a combination of the latter with a change in the design (or proportions) of a water-gas set. The preceding statement, the reader will understand, refers more particularly to a carburetted water-gas set.In the manufacture of water gas from coke, present practice requires that for continuous 24-hour service the heat of combustion of all the carbon monoxide (CO) generated during the air blow be utilized in addition to the sensible heat of the gas coming from the generator. This is doubly true when making carburetted water gas from bituminous coking coal. The reasons why this is so are apparent when the following factors are considered."

Nov 1, 1920

One Data Set for the Lifecycle Complete data captured at the logging stage benefits the entire life cycle Exploration Technical Studies Production and Milling Visible Light Spectrum Hyperspectral, put simply, is the interaction of light with matter based on the nature and chemical structure of the specimen. SpectrumWe develop the library to match the liberation size fraction Analyses every 1mm2 1 meter of NQ core = 35 000 analysis data Crystal size detection : 0.1 micron

May 1, 2013

By John J. Gilman

BECAUSE of their layerlike structure, zinc crystals exhibit strong anisotropies for almost all physical and chemical properties. This should, and indeed does, greatly influence the plasticity of zinc for various crystal orientations. At low temperatures, the investigator of this plastic anisotropy is plagued by the great variety of deformation modes that operate. However, at high temperatures (250° to 419°C) only two deformation modes predominate: basal (0001) and prismatic (1010) glide. Furthermore, since strain hardening is virtually absent at high temperatures, the plasticity for these two modes of deformation can be very simply described by means of two equations of state. It is the purpose of this paper to describe the experimental behavior of basal and prismatic glide in zinc crystals, and to interpret this behavior in terms of other physical properties (in particular, the thermal expansion coefficients and the elastic constants) using the theory of dislocations. Fig. 1 defines the two planes of the zinc structure that will be discussed. Glide occurs very readily on the basal planes at all temperatures, and there is a very large literature on this subject. Much of the literature has been reviewed by Schmid and Boas;' it will not be reviewed here. Kolesnikovl was the first to show that if basal glide is circumvented by stressing a zinc crystal parallel to the basal planes (giving zero shear-stress on the basal planes) then, at temperatures above about 320°C, glide on the first-order prism planes occurs. His results have recently been confirmed by Cahn, Bear, and Bell." These previous workers have established the existence and crystallographic elements of prismatic glide; the present paper is concerned with the stress, strain rate, and temperature relations of prismatic glide as contrasted with basal glide. Experimental Methods The crystals were square ones, 6x6 mm, that had been grown in precision Pyrex tubes by a method that is described in detail elsewhere.' Most of the crystals were 99.999+ pct Zn (New Jersey Zinc Co. CP grade). Some were alloyed with 0.1 -+-0.005 atomic pct Cd, and chemical analysis showed that almost all of the added cadmium persisted through the crystal-growing process. For measurements of nonbasal glide, crystals were oriented with their basal planes parallel to both the rod axis and one of the flat faces of the square cross section. However, the orientation of the close-packed directions [1210] with respect to the rod-axis was variable. For basal glide measurements, the angle between the basal plane and the specimen axis was 35". The orientations were measured by the Gren-inger back-reflection X-ray method. The problem of finding a suitable method of gripping the crystals was the most serious experimental obstacle that arose. Because of the large plastic anisotropy of zinc, the usual gripping methods were unsatisfactory. Some methods that were tried were: high melting-point solder, making heads on the ends by locally melting a crystal, and electroplating nickel on the ends to form enlarged portions. For all these methods, the regions of the grips were weaker than the crystals themselves. Finally, two methods were decided upon: bend tests and direct machining of tensile specimens. In the bend tests, specimens were loaded as simple beams so that gripping was not a problem. The beams were 1 in. long and the axis of bending was parallel to the hexagonal axis of the crystals. For the crystals that were machined into tensile specimens, brass bars with slots in them were used to support the crystals, and thereby minimize the distortions due to machining. The crystals were glued into the brass bars with plastic cement which was later dissolved away with acetone. See Fig. 2, left. No clamps were used near the crystals and the machining was done using a milling machine with a fly-cutter. The tool bit was very sharply pointed to minimize burnishing. The feed was less than 1 mil per cut. The depth of cut was 2 mil for roughing cuts, and % mil for the finishing cuts. This machining method produced surface layers of tiny recrys-tallized grains only 2 to 3 mil deep, and the bodies of the crystals were not measurably disturbed. After the crystals had been machined and removed from the brass holders, they were chemically polished until about 5 mil had been removed from all their surfaces. The polishing reagent consisted of equal parts of concentrated HNO,, 30 pct H3O and ethyl alcohol; it is described in detail elsewhere." A typical crystal is shown in Fig. 2, right. The I-shaped faces are normal to the hexagonal axis of the crystal; otherwise the projections at the ends would simply shear off when the crystal was loaded. The cross section in the 2?-in. gage length is 0.215x0.115 in. It was found that the polished

Jan 1, 1957

By D. M. Slavich

"In today's operating and investment climate, project evaluation is both more important and more difficult. It is more important because economic and financial analyses of a proposed project provide a basis for judgment of a project's commercial viability by equity participants, lenders and, in some cases, other participants such as off takers and governments. It is more difficult because these analyses must, of necessity, be based on estimates, projections and evaluations which must be made in a period remarkable for its economic and political uncertainty.Project evaluation starts with the analysis of the engineering, commercial and financial information available. Beginning with the preliminary design and capital cost estimates, alternative financing plans can be developed outlining possible sources of funds, terms and security arrangements. Pro-forma financial statements can also be developed, including sources and uses of funds, cash flow schedules, income statements and balance sheets. With these results, various profitability measures can be determined.Subsequently, in an effort to deal with uncertainty, these results can be tested by measuring the impact on project viability and profitability of changes in project and external variables such as product process, mining and processing rates, operating and financing costs, currency exchange rates and other factors.The results are a number of financial projections reflecting different assumptions for key project parameters. The projections can be used to structure the project to achieve the maximum financial performance. Projects, the financial viability and profitability of which can be demonstrated under varying market conditions, will be the most competitive in capital markets."

Jan 1, 1982

The Third Session of the Forty-Sixth Meeting of the Rocky Mountain Coal Mining Institute convened at the Hotel Colorado, Glenwood Springs, Colorado, June' 20, 1950, at 9:30 a.m., G. E. Sorenson, President, presiding. PRESIDENT SORENSON: The meeting will come to order. To refresh your memory, I will read off the names of the people on the various committees. President Sorenson read off the names on the committees. Mr. Whiteside, do you wish to make an announcement? MR. WHITESIDE: Yes, I would like to 'say a word. .4s you know, this afternoon you will be on your own, and I think some would like to go to Rifle. I wonder if we could get a vote on that now as to how many would like to go to Rifle, as they at Rifle would like to know so they can provide conveyances. There seems to be about 14 or 16 that would like to go to Rifle.

Jan 1, 1950

By C. W. Langenberg, D. E. Macdonald, R. S. Strobl

"The successful marketing of Alberta coals will increasingly depend, to a large degree, on an extensive coal quality information base. This information, at present, is generally based on a deliverable, cleaned coaland is confined to existing mine sites. Coal quality information is not as well understood for raw in situ coal outside of mine sites and even less is known about the geological factors that control it.If new uses and markets for Alberta coal are to be developed, such as gasification, coprocessing, and exploiting high rank coals for combustion, it will be imperative that the coal quality parameters important for these utilizations be known. These parameters need to be known for existing deliverable coals and, just as important, for as yet unexploited in situ coal. Factors such as the Cl, No, K, Co, P and trace element contents should be addressed to meet the requirements of these new utilizations.The geological characterization and explanation of what factors control these coal quality parameters is part of research being done at the Alberta Geological Survey. In-seam vertical profiling has been undertaken within the plains and foothills/mountains coals to determine exactly where coal quality variations occur and why. In the Ardley coal zone at the Highvale Mine it has been found, for example, that the ash content of the mined coal is made up of discrete partings and of microsized particles associated with inertinite macerals. The in-seam characterization of coal seams will lead to a better understanding of in situ coal quality variations, leading to new uses and markets for Alberta coal."

Jan 1, 1993

By A. F. Giamei, E. J. Freise

A discussion of the various factors affecting the accuracy of volume fraction determination by the direct comparison X-ray diffraction method is presented. To minimize errors introduced by nonrandomization effects such as preferred orientation and large grain size, as well as errors introduced by statistical effects, an iterative mathematical analysis is introduced. This analysis is applied to all observable diffractio~ spectra from a given specimen by means of computer techniques and is statistically superior to the standard direct comparison technique which utilizes only one or tm sets of intensity spectra. The computer program also presents a graphical interpretation of- the results which enables the investigator to visualize and readily assess the scatter in volume fraction estimates caused by deviations from randomness. Finally, the iterative analysis is applied to experimental data collected from a series of plain carbon steels in both the as-received and spheroidized conditions to determine the volume fraction of cemen-tite present in each case. The results show markedly good agreement with chemical analyses for all spheroidized specimens. In theory, quantitative X-ray diffraction is a power-ful analytical technique for precise determination of the volume fractions of various phases present in a multiphase poly crystalline aggregate. There are two generally used methods; both utilize the fact that the intensity of a diffraction line of a particular phase is a function of volume fraction of that phase present in the aggregate. The more common method is the so-called internal standard technique where a known amount of standard substance is mixed with the aggregate containing the unknown. The resulting ratio of the intensity of a particular diffraction line of the unknown to the intensity of a diffraction line from the standard is used to find the weight fraction of unknown material by reference to the intensity data obtained from a previously prepared set of standards containing the same amount of standard material. The details of this technique are outlined in standard works on X-ray diffraction.' The disadvantages of the technique are that it requires the use of powder specimens and that the powder mixture must be homogeneous near the surface to the maximum effective beam depth. The alternative technique is the direct comparison method in which the ratio of the intensity of a diffraction line of a phase in the aggregate to the intensity of a second-phase diffraction line yields the ratio of the volume fractions of each phase present. This method has been applied most extensively to the determination of the percentage of retained austenite in martensitic steels and to determining the amounts of hcp and fcc allotropic modifications in pure cobalt5 and the amounts of hexagonal and rhombohedra1 modifications in graphite.8 This method is applicable to bulk as well as powder aggregates and is the technique which will be considered in the following text. It is the purpose of the present communication to show that by combining the results of X-ray diffrac-tometry with the use of high-speed digital computers the results of the direct comparison quantitative X-ray analysis technique can be optimized by using all of the data available on a diffraction pattern. THEORETICAL DISCUSSION In optimizing any quantitative X-ray diffraction experiment, the problem of accuracy vs time to collect and analyze the experimental data arises. For any method to be practical, it is required that both experimental and analytical procedures are reasonably short. In most of the previous work performed by the direct comparison method, intensity data from only one or two sets of peaks were used to calculate the volume fraction of phases present in the aggregate. Consequently, rather long-time experimental measurements are required to assure that the intensity data are sufficiently accurate to justify the use of one or two sets of data. By using computer techniques to analyze the experimental data it becomes feasible to use all of the available data on a diffraction pattern. By so doing, the time spent in measuring any one diffraction maxima can be appreciably reduced. Although this results in poor counting statistics for any one maxima, the number of data points available for analysis is greatly increased. Based on the above discussion, it will be assumed that a continuous scanning counter-diffractometer technique will be used to collect intensity data from a two-phase mixture. The integrated intensity of the ith diffraction line from the a phase in the aggregate is given by:'" where is the volume fraction of the a phase, The various quantities in Eq. [la] are angular independent while those in [lb] depend on the hkl spectrum of a particular phase. The meaning of the individual quantities in Eqs. [la] and [lb] are given in Appendix 1. It is convenient at this point to outline briefly the factors which will affect the measured intensity of any one hkl spectrum. a) Extinction effects arise from two independent experimental conditions. Primary extinction arises from a high degree of crystal perfection and results in spectra having lower intensity than predicted by Eq. [I]. Any treatment, such as powdering, which reduces

Jan 1, 1968

By D. Bahrami, W. K. Asante, G. L. Danko

It is prudent to interpret atmospheric monitoring signals in real time for checking the safe limits of the air conditions in underground mines. In gassy mines, real-time evaluation increases the safety of operations. In all mines, continuous monitoring and evaluation contributes to maintaining air conditions within healthy and safe limits. Signal interpretation for safety conditions in mines is difficult for many reasons. An increase in hazardous contaminant concentrations can be predicted by signal pattern recognition, root cause analysis of rapid changes toward deterioration, and forward prediction in time using algorithms and numerical models. The paper describes an early warning system for analyzing monitored signal patterns continuously in real time as well as forward predicting the various environmental and working conditions to recognize dangerous trends that may affect safety and health in underground mines. A dynamic, numerical ventilation model with heat and gas contaminant simulation components is used for the analysis of atmospheric data. Methods and test results are discussed with numerical examples for signal propagation prediction. Several mine examples are studied using controlled, synthetic data for malfunction simulations to evaluate time delays between the detection time of suspicious signal trends and the time of dangerous threshold crossing marking an accident scenario. Delay time is found in the order of 20 min in the examples, signifying the useful time period for preventive intervention between EWS warning and the likely breakout of a following accident.

By Baxter D. A

This paper, one of two written about the Queensland Railways Brunswick Street tunnels presented at the VIII Australian Tunnelling Conference, 1993, describes the design and monitoring aspects of the railway tunnels built between Central Station and Brunswick Street Station.The design was mainly influenced by the need to minimise settlement of buildings above the route. The performance of the design details and the monitoring of the tunnels are briefly described.Appendices include extensions to the work of Curtis in the analysis of circular tunnels in a viscoelastic ground.Reference: Asche, H R and Baxter, D A, 1993. Design and ground support monitoring of the Brunwick Street rail tunnels, Brisbane, VIII Australian Tunnelling Conference.

Jan 1, 1993

By Nemick JA

Recent advances in computer simulation together with field measurements of caving and microseismic activity about longwall panels, has allowed a much better understanding of the caving process and the variability due to geology. The joint research between SCT Operations and CSIRO Division of Exploration and Mining has initiated new methods of computational modelling predicting various caving patterns and strata failure far ahead of the longwall face. This work was validated by field measurements of caving and microseismic activity at the longwall face.The rock fracture distribution and the caving characteristics of a range of strata sections have been simulated by computer methods. Validation studies of the method were addressed together with case studies. The interaction of caving with support convergence and face control is presented. The method allows the simulation of longwall support behaviour under various geological conditions. The system also allows a prediction of the monitoring data, which is best suited to give an early warning of weighting events or signal various key caving characteristics.

Jan 1, 1998

By Walter V. Knopp, Laurence Delisle

INTRODUCTION THE aim of this work was the preparation of nickel-steels from elemental metal powders by powder metallurgy techniques. It was known that plain carbon steels could be made from a mixture of iron powder and graphite and that the effect of carbon on iron in powder form was of the same nature as that produced in fusion metallurgy. The problem in making nickel steels from elemental powders consisted therefore in finding out whether sufficient diffusion of the nickel and other incidental metals normally present in such steels could be induced in the solid state to modify the properties of plain carbon steels made from powders and produce the beneficial effect of alloying. The composition selected originally was that of an S.A.E. 2330 steel. Metal powders, in the proportion corresponding to that composition, were mixed with graphite, pressed, and heated at different temperatures for different periods of time, to produce bonding of the metal particles and mutual diffusion of the various elements without melting. Temperatures up to 1325°C and sintering periods as long as 6 hr were first investigated because it was expected that such conditions would produce maximum diffusion with an accompanying improvement in the properties of the alloy. It was found that, although diffusion proceeded to a large extent under the conditions investigated, it would not be complete unless sintering were carried out at a high temperature for much longer than 6 hr. Relatively high temperatures and long sintering times are objectionable from a practical point of view, particularly when a low cost material is to be produced, because they necessitate the use of special, costly equipment. Work could be done to improve the diffusion of iron and nickel by changing conditions other than the sintering temperature and time, i.e., finer primary or alloy powders could be used. However, a marked change in the properties of the steel had been observed even with only partial diffusion. It was thought, therefore, that instead of trying to improve the diffusion, advantage might be taken of its incompleteness to produce a special structure consisting, in the unquenched condition, of a hard constituent, rich in nickel, dispersed in a tough pearlitic matrix. Steels with such a structure, not readily obtainable by fusion, should have desirable mechanical properties. Besides, it should be possible to prepare them from elemental powders under economical conditions. This latter alternative was therefore adopted for the second phase of this work. This report is divided into four parts: 1. General Procedure. 2. Effect of Sintering Temperature. 3. Effect of Varying the Nickel Content. 4. Effect of Alloying Elements. GENERAL PROCEDURE The general technique of cold pressing as used in powder metallurgy was applied.

Jan 1, 1948

By Ernest F. Burchard

A Reconnaissance of the manganese- and chrome-ore deposits of Cuba was made by the writer, as a representative of the U. S. Geological Survey, in company with Mr. Albert Burch of the Bureau of Mines, under instructions of the Secretary of the Interior, in the spring of 1918. The Cuban Government courteously detailed Sr. E. I. Montoulieu, a mining engineer connected with the Treasury Department, to act as escort and associate throughout the work on the island. The object of the study was to obtain authentic information for use of the United States Government as to the location, character, quantity, and availability of the manganese- and chrome-ore deposits in Cuba. Accordingly, the work comprised examination of such deposits as seemed to be of promise, without regard to stage of development, with a view to a determination of the quantity and quality of ore likely to become available for shipment during 1918 and 1919, and of the tonnage of ore in reserve. Wile it was possible to visit most of the deposits that seemed to be of promise, there was not sufficient time to visit all that were brought to our attention, some of which may have merit. Moreover, the necessity for paying particular attention to the ore deposits and the mines precluded the possibility of making more general studies of the geology of the region, and of making satisfactory collections of country rock and of fossils, and so for other details as to the geography and geology of Cuba the reader is referred to the report by Hayes, Vaughan, and Spencer.l Mr. Burch returned to the United States about 10 days in advance of the writer, who continued, in company with Sr. Montoulieu, investigations of reported deposits in Pinar del Rio, Matanzas, and Santa Clara Provinces. On his arrival in Washington, Mr. Burch submitted to the Director of the Bureau of Mines a summary of the results of the work to date. Later the writer published, as Press Bulietin 190. 380 of the U. S. Geological Survey, a statement concerning the chrome and man-

Jan 1, 1920

By J. W. Adams

Measurements of surface magnetic field noise were made at various locations over the Geneva Coal Mine near Price, Utah, on June 12, 1973. The locations selected were on the surface over emergency locator beacons underground at depths between 3S0 meters (1150 ft.) and 488 meters (1600 ft.). The surface terrain where these measurements were made was mountainous, and access was difficult. There were no power lines within several miles, and the weather was clear; therefore, the magnetic noise levels were about as low as will normally occur. Results of measurements of distant sferics indicate rather sharp cutoff frequencies below which broadband, impulsive noise is attenuated. The mechanism of propagation for this noise above the daytime cutoff frequency of 3500 Hz and the nighttime cutoff frequency of 1700 Hz is deduced to be a waveguide formed by the D or F layers of ionosphere as an upper plane and the earth as a lower plane.

Jan 1, 1974

By J. Ramirez-Castro, J. A. Finch

"Galena is the finest component of the product of a closed-circuit grind treating a lead-zinc ore, largely due to preferential recycling of this high-density mineral by the cyclone. For example, at the Pine Point Mines concentrator, for ~ 55% -200 mesh over-all, the galena will be close to 95% -200 mesh. This sliming of the lead can limit recovery, selectivity and dewatering. A proposed circuit modification to reduce the sliming is to incorporate a unit cell. A simulator was constructed to study the No. 3 grinding circuit at Pine Point modified by a unit cell on ball mill discharge (BMD).The simulator used a cumulative size basis rate-of-breakage with plug flow ball mill model, the parameters being obtained by laboratory grinding tests. Flotation and the cyclone models used a cumulative recovery/size matrix. The behaviour of each mineral, galena, sphalerite, pyrite and calcite/dolomite, was simulated. Simulation was adapted to a programmable calculator. A close fit to the existing circuit performance at two tonnages and mineral mixes was established.The simulator showed that the modified circuit could significantly coarsen the Pb grind, from 95% to —50% -200 mesh, depending on recovery, without substantially altering the size of the other minerals. The other principal findings were: compared to laboratory flotation tests on existing circuit BMD, the unit cell concentrate (CONC) will be coarser and markedly lower in grade; relatively low unit cell stage recoveries are desirable, because the cyclone scavenges the tail to give a circuit recovery which is higher than the unit cell stage recovery; unit cell stage recovery should not exceed the cyclone stage recovery, as the latter is the maximum circuit recovery; low unit cell stage recovery helps offset the disadvantage of the high flow at BMD; other high-density minerals will also be scavenged into the CONC, as illustrated by pyrite, making CONC quality difficult to maintain; density control of BMD flotation does not greatly alter feed density to the cyclone or ball mill.Possible plant metallurgy is forecast for a CONC diverted to final lead concentrate."

Jan 1, 1980

By R. A. L. Black, J. E. Jennings

The problems of slope stability in open cast mines are examined. A criterion, the instantaneous stripping ratio, is suggested for use in the design of pit slopes and as an index of control at all stages of the exploitation of the orebody. This criterion may also be related to safety and to the maximizing of profits. Two approaches to safe design of slopes, one from the point of view of soil mechanics and the other from the point of view of rock mechanics, are described and critically compared. The effect on slope stability of the regional tectonic stress field is discussed. Explanation is given of the application of the Terzaghi effective stress concept to problems in both soil and rock environments, including possible effects when borehole deformation techniques are used to measure stresses in rock in situ. A company embarking on open cast mining is faced with two basic questions: 1) will the venture be profitable and 2) can it be carried out with safety? The two questions are obviously interrelated because both depend upon the slope angles adopted for the pit. The cost of open cast mining depends largely upon the stripping ratio, defined as the volume of overburden that must be removed to the volume of ore recovered. The steeper the slope angles, the more favorable the stripping ratio, but the stability of the slopes, and therefore the safety of men and materials in the pit, require that the angles be made relatively flat. Consequently, the design depends upon a compromise: the slopes must be steep enough to result in economical mining and flat enough to ensure safety. Today there is a world trend towards deeper mining by open cast methods. This is mainly due to the higher cost of underground mining and the lower cost of open excavation resulting from the introduction of large modern earth and rock-moving machinery. Deeper open cast mining has led to a very great increase in the volumes of wasted overburden, and much thought is being given to the considerable economic benefits which would result if pit slopes could be made steeper by even one or two degrees. The result has been an increasing interest in research into slope stability problems in the expectation that the application of scientific principles will provide solutions leading both to economies and to more predictable operation of the mines. In at least four places, the U.S., Australia, Western Germany and Southern Africa, comprehensive investigations are at present in progress, and it is the object of this paper to review some of the more important aspects of these programs. RELATION BETWEEN ECONOMY OF OPERATION AND SLOPE ANGLES The main object of any industrial enterprise in a free economy is to make a profit. In mining, where profits must be made from a wasting capital asset, a further definition of the profit motive is imposed, namely that the economic aim should be to maximize the total possible profit. But since profits deferred for a number of years are not as valuable as profits that are immediately available, it is usual to discount deferred profits at some rate of interest which reflects their current or present value in the hands of the investor. Thus, in mining the logical aim can be defined more closely still: to maximize the present value of the total future profits. In commercial terms the present value represents the market value of the operation as a going concern. Many factors enter into the forecast of current and future profits. They include the volume of production, the price of the salable product and the cost of production. Current profits can be estimated with reasonable accuracy by the operating engineers; but it is the task of economists and management to assess future trends in the mineral markets and in the economy as a whole, and together with the engineers, they can then estimate the future cost and profitability of the mining operations. In open cast mining, the rate of ore production once decided on remains a virtually constant factor unless a major change in the capital structure of the mine is made. But one factor over which the operator has a considerable measure of control is the ratio of the volume of ore mined to the volume of waste over-

Jan 1, 1963

By A. P. Watt

Foreword...............................................................323 Location of District..................................................... 324 Geology and Mining..................................................... 325 Topography and Climate................................................. 325 Lcad Production of the District...........................................325 Operating Companies in Southeast Missouri................................ 327 History of the District................................................... 329 Present Method of Treating the Ore....................................... 335 Character of Ore Treated...........................................338 Chemical Analyses............................................. 339 Description of Polished Specimens.................................340 The Concentration Problem of the District............................. 341 Handpicking at Mine La Motte....................................... 343 Crushing............................................................344 Roll Practice in the District.......................................... 346 Screening Practice................................................... 347 Jigging the Ore..................................................... 347 Bull Jigging.................................................... 348 Hancock-jig Practice............................................ 348 Classification of the Ores.............................................. 350 Table Treatment....:............................................... 352 Regrinding of Middling.............................................. 354 Description of Marathon Mill..................................... 358 Results of Preliminary Tests.....................................359 Rod Wear in the Marathon Mill.................................. 367 Steel Consumption.............................................. 368 Design of Marathon Mills.............. :......................... 368 Treatment of Table Middling........................................ 368 Slime Concentration................................................. 370 Methods Used in the Past.......................................370 Present Methods of Treatment................................... 371 Flotation of Slime.......................;........................ 371

Jan 1, 1918

By K. H. Singh, J. N. Szuck, J. A. Riddell

"Hydraulic rock drilling equipment has been in use at Falconbridge over the past two years in both production and development situations. This paper deals with the experience gained in the application of hydraulic drilling in the company's mines and discusses the benefits and problems encountered during their use. The paper primarily focuses on technical, operating, maintenance and economic aspects of the machines, and does not attempt to compare the performances of different machines from the various manufacturers.IntroductionThe Sudbury Operations of Falconbridge Nickel Mines Limited are comprised of five operating mines and two mines under development. All the production comes from underground mines, mostly at depths below 1000 metres. The company, faced with increases in operating costs and difficult mining conditions, has continued to seek solutions with the help of new mining technology.The development of electric-hydraulic drilling machines in Europe had been pursued with great interest and, in 1979, a decision was made to test these machines to prove their technical and economic viability under operating conditions. Since then, a number of electric-hydraulic machines have been evaluated in different situations and currently nine hydraulic machines are being used in the company's various mines. These machines are comprised of two-boom drilling jumbos for development, one-boom machines for longhole drilling and a large-hole-diameter drilling rig for blasthole drilling. One hydraulic jumbo has also been used in a cut-and-fill stope."

Jan 1, 1982

By C. O. Fairchild

ONE of the fundamental principles of efficiency is the use of adequate and permanent records. The rapid increase in the manufacture and use of recording pryometers is a proof of the appreciation of efficiency principles on the part of the manufacturers engaged in the various technical industries. Where recording pyrometers are not employed in an industry in which temperature measurements are necessary, one will generally find that a printed form is used upon which is written, periodically, the temperatures measured by an indicating instrument. It is no serious condemnation of the workman to state that such records are often "doctored," but it is rather a reflection upon the executive who puts such temptation in the way of a workman. One of the well-known "tricks of the trade" is to "force." a furnace so that it will be at the proper temperature during the periodic trips of the foreman or other official. Indicating instruments and recorders may be used together to great advantage. The recorder furnishes .a printed record and a check upon the operator of the furnace, and a record of value in correlating properties of the finished product with the heat treatment. The indicator should be of assistance to the operator in controlling the furnace or oven. Modern practice requires a temperature-recording instrument that is as simple as possible, rugged, reliable, and sufficiently accurate. Of these qualifications reliability is paramount, particularly in cases where the recorder is used for controlling the temperature automatically. By a reliable instrument is meant one that will run continuously with little attention and with a consistent degree of accuracy. That is, if it is in error by 5 per cent. one day, it must be in error by a like amount on any other clay, and not by 2 per cent. or 10 per cent. The earlier forms of recorders were complex and delicate, or mechanically unsatisfactory and inaccurate, and required considerable attention to keep them in operation. Within the past few years, however, the development in the manufacture of temperature recording devices has been highly satisfactory and many excellent instruments are now available. .

Jan 9, 1919

By T. Holmes, S. Davison

"The Special Standard Surge bin at Agrium’s Vanscoy Potash Operations (VPO) has been plagued with flow problems and wear, and corrosion issues for it’s entire working life. Investigation showed that the carbon steel construction, bin geometry, and resultant funnel-flow pattern were directly responsible for production losses and disproportionate maintenance and capital costs. Potash enters this bin at between 140°C and 165°C, but the stagnant potash outside the active flow channel was much cooler, allowing moisture to migrate toward the outer regions, which caused corrosion of the walls and reduced live capacity as the potash in this area hardened and built up on the walls over time.A 2013 inspection revealed holes and paper-thin areas in the lower cylinder wall sections and in the conical hopper. The only thing preventing major leaks and even a potentially catastrophic failure was the buildup of stagnant hardened product on the cone walls. It was concluded that the cone had reached the end of its life and required replacement. VPO’s original plan was to replace the cone in kind and repair the cylinder as necessary; however, a failure-mode and bin-performance investigation combined with a lifecycle- cost analysis indicated it would be better to redesign the hopper.For success in retrofit projects, it is essential at the design stage to consider the bulk solid flow properties and the operating environment involved. Because education in this area is not offered at a university level, engineers often do not fully appreciate the effects of the flow properties of bulk solids on bulk material handling equipment.Jenike & Johanson conducted flow properties tests on samples of potash and using the data, redesigned the bin and the feeder. After the modifications, VPO’s surge bin provides safer, more reliable operation with a much longer predicted working life. Using this retrofit as an example, we aim to provide a general understanding of bulk solids flow theory and highlight the importance of customizing the design to the appropriate flow properties in the cost effectiveness, reliability, and safety of a bulk material handling system."

Jan 1, 2016

THOSE MARKED THUS * ARE MEMBERS, MARKED THUS ?ARE ASSOCIATES. THESE SIGNS DOUBLED INDICATE LIFE MEMBERS AND ASSOCIATES RESPECTIVELY. THE FIGURES AT THE END OF THE ADDRESS INDICATE THE YEAR OF ELECTION. HEAVY-FACED TYPE SIGNIFIES HONORARY MEMBERSHIP. *AARONS, J. BOYD, Vivian Gold Mining Co., Ltd., Harris, West. Australia. '05 *ABADIE, EMILE R., Cons. and Min. Engr., 214 Union Savings Bank Bldg., Oakland, Cal. '76 ?ABBÉ, MAX F., Prest., Abbé Engineering Co, 220 Broadway, New York, N.Y. '07 ? ABBÉ, PAULO., Secy.,Abbé Engineering Co., 220 Broadway, New York, N.Y. '07 *ABBOTT, AI ARTHUR Morococlia, Peru, So. America. '95 *ABBOTT, CLARENCE Chief EDgr., Iron Mines, Dic Tennessee Caol, Iron & R. R. Co., Bessemer, Ala. '04 *ABBOTT, JAMES W., Min. Engr: Ploche, Lincoln Co., Nev. '94 *ABE, MASAYOSHI, Prof. of Mining, Imperial University Kyoto, Japan. '05

Jan 1, 1910