Search Documents

By C. L. Lin

The image-based On-line Particle Size Analyzer (OPSA) system has been developed at the University of Utah to measure particle size distributions under plant conditions where overlapped and segregated particles are being transported on a moving belt conveyor. Evaluation of the OPSA system at several plant sites has been completed. The results show a consistent agreement between the particle size distributions obtained from the OPSA system and those obtained from laboratory screen analysis of belt samples. These results and the stable performance of the OPSA system during the field tests suggest that continuous quality control of crushed products is possible using the OPSA system.

Jan 1, 1999

By R. L. Grayson

Conventional mine safety wisdom states that "the most efficient mines are also the safest." Since the 1980s, small mines (and contractors) have been targeted as the most dangerous ones because of their fatality records. Statistical testing of 1993 West Virginia safety and production data indicated that the most efficient WV mines were not the safest ones, considering correlations between the severity measure and tons per employee-hour, except for very small mines. This paper will present the results of an extended analysis of WV mine safety using 1993 and 1996 data, concluding with the method used to suggest current priorities for focusing interventions.

Jan 1, 1998

By H. A. Watson

Laboratory tests on three commercial methane detectors, two combustion-type detectors and one interferometer-type detector, were made by the Bureau of Mines to determine their response to certain single and multiple flammable gases mixed with normal and abnormal air atmospheres. Although both types of detectors responded accurately to methane-normal air mixtures, they did not show correct concentrations for other single flammable gases in air. Uniquely, the response of the interferometer-type detector to hydrogen was in a negative direction. The effects of individual gases in multiple flammable gas mixtures were approximately additive. In oxygen-deficient atmospheres the methane response of the interferometer-type detector erred on the high side, but only in very low oxygen concentrations were the combustion-type detectors affected-showing low, erratic methane readings.

Jan 1, 1966

By S. F. Guo, Z. F. Zhan, X. L. Huang, Y. Zou, S. W. Qi

"FLAC3D is an important numerical analysis software to study dynamic response of rock slope. In application of the program, the common issues such as absorbing boundary and the method to apply wave have been well studied. However, effects of model mesh size, damping and width of slope are still unknown. In order to make the result more convictive, this article has discussed the above issues systematically. It found that when the maximum mesh size is smaller than 1/10~1/8 of the smallest wavelength, the mesh size is smaller, the computational accuracy is higher. Meanwhile, values of damping and width of slope have no effect on the result. Additional, results of FLAC3D modeling on wave transmission across rock joints agree well with analytical solutions, so it has verified the capability and accuracy of FLAC3D on dynamic response of rock slope.INTRODUCTIONChina is a mountainous country accompanied with many earthquakes. Thousands of geological disasters are triggered by the Wenchuan Earthquake in Sichuan Province, and the majority of the disasters are landslides induced (Xu et al., 2009). Meanwhile, the paper (Li et al., 2003) points out five significant issues about dynamic loading in the area of geotechnical engineering, which includes the study of rock slope stability under earthquakes, and the dynamic response of rock slopes is one of its important study issues."

Jan 1, 2015

By 1980, the U.S. mining community had reached a broad consensus regarding coal pillar design. The pillar load could be estimated from tributary area theory, and the pillar strength from empirical formulas and laboratory coal strength testing. Then the growth of longwall mining required new thinking. Recently, powerful design methods have emerged from analysis of large data bases of real-world pillar successes and failures. These include the Analysis of Retreat Mining Pillar Stability (ARMPS), the Analysis of Longwall Pillar Stability (ALPS), the Mark-Bieniawski rectangular pillar strength formula, and guidelines for preventing massive pillar collapses. Sophisticated numerical models have also helped transform the pillar design landscape. In the process, our understanding of pillar mechanics has been greatly enriched. A new paradigm divides pillar failure into three categories:

Jan 1, 1999

By Sunil S. Basarkar, Dilip M. Dewaikar, Rajesh H. Gajjar

"A load transfer program AXPILE was developed for simulation of the loadmovement characteristics of socketed piles of the Mumbai reg ion. This program used empirical relationships for ultimate shaft resistance at pile-rock interface recommended by Zhang and Einstein (1998). According to their recommendation, ultimate shaft resistance at pile-rock interface is related to the square-root of uniaxial compressive strength of intact socket material by a parameter C, which ranges from 0.4 for smooth sockets to 0.8 for rough sockets. Results of three instrumented pile load tests were compared with the AXPILE generated results. The comparison of analytical and field estimates of the unit shaft resistance confirm the recommendations of Zhang and Einstein (1998) on the unit side shear parameter c,, which was found to be in the range of 0.35 to 0.67.INTRODUCTIONInstrumented pile load tests were carried out on the test piles at the Bandra-Worli sea link project in Mumbai city of western India. High capacity socketed piles were required to take up loads from the superstructure. Hence, in addition to the available toe resistance, an accurate measurement of the shaft resistance in socket portion was desired. The instrumented load tests incorporated Osterbergcell (0-cell) assisted by strain gauge instrumentation to estimate the shaft resistance mobilization in the socket portion.AXPILE load transfer program was developed for load-movement simulation of socketed piles (Basarkar, 2004). The load transfer algorithm based on Coyle and Reese (1966) was incorporated in this program, which used empirical correlations and functions to account for load transfer in piles through shaft and toe resistance.This paper compares the computed unit shaft resistance from the AXPILE program with the measured values recorded from the instrumented pile load test."

Jan 1, 2005

By M. Fan, Z. Long

"This paper presents some studies on recovering valuable elements from Chinese coal by-products, including coal combustion fly ash, stone coal ash, and coal flotation tailings. Both commercialized technologies and economic potential recovery methods are described in this study. Magnetically stabilized air-dense medium fluidized bed separation, tribo-electrostatic separation, froth flotation, and hydrometallurgical methods are discussed in recovering various valuable elements in Chinese coal by-products from different coalfields. These valuable elements include iron, carbon, aluminum, rare earth elements, lithium, gallium, germanium, uranium, titanium, scandium, silicon, vanadium and phosphorus, etc. The ultimate goal is to fully utilize all valuable elements in coal by-product. Each component within coal by-product should be efficiently segregated to its highest value. INTRODUCTION Coal is mainly composed of energy-producing elements carbon and hydrogen. In addition to these elements, coal usually contains many other valuable elements, including iron, aluminum, silicon, rare earth elements, lithium, gallium, germanium, vanadium, uranium, titanium, scandium, and phosphorus, etc. These coal-associated elements are significantly enriched in coal combustion by-product fly ash because of majority of main components, carbon and hydrogen elements, being removed. Table 1 provides the chemical composition range of the main elements oxides in 12 Chinese fly ash samples collected from coal power plants located in Northeast China, Northwest China, Southwest China, and Southeast China. It can be seen from Table 1 that the major mineral components of different ashes are similar, but the bulk chemistry of different fly ashes may vary widely due to the changes of ratios of the mineral components in different coals. The major mineral components in various Chinese coal combustion fly ash are silicates, iron oxides, and unburned carbon."

Jan 1, 2017

By Mostafa O. El-Bealy

"To estimate the interdendritic cracking tendency in casting processes, a new model for interdendritic cracking criteria has been proposed. The model combines a concept of the alloying element effect on the interdendritic strain generation and therefore on the susceptibility of interdendritic cracking phenomena. A susceptibility of interdendritic cracking is modeled by using El-Bealy's interdendritic cracking susceptibility function ""BJCSF' and the opening displacement between the dendrites ""EIA "". These concepts are modeled based on the previous experimental observations and ElBealy' approach. The model is implemented numerically for a one-dimensional model problem with some similarities to the casting of steel. The variation of some key parameters that are known to influence the frequency and severity of the interdendritic cracking is then studied.I. INTRODUCTIONInterdendritic cracking ""hot tearing"" commonly encountered in both ferrous and nonferrous castings (1,2]. It is generally believed that interdendritic cracks start to nucleate and develop in the interdendritic strain region within the mushy zone [l-5]. The interdendritic strain region is then definitely coherent, but continuous films of liquid still exit (4,5]. This distinguishes interdendritic cracks from cold cracks forming during the casting process after complete solidification (6,7].Much effort has been put into the understanding of the interdendritic cracking phenomena, and several theories have been proposed. Fellini [8] stated that interdendritic crack ""hot tear"" will result if the material is subjected to too high of accumulated strain within so called vulnerable part of the solidification interval. Kinosita et. al. [9] and Campbell (10] also emphasized the role of tensile stresses in the forming of interdendritic cracks. Most interdendritic cracks criteria simply consider the size of solidification interval, stating that solidification range is associated with a lager interdendritic cracking susceptibility than a short range. Clyne and Davies (11] formulated a more refined such criteria based upon the time spent in different regimes of the solidification interval. They defined a vulnerable region in which thin continuous films of interdendritic liquid exist, and the permeability is low. When thermal strains are induced in this region, the film is not able to sustain the stresses, and an interdendritic crack will form."

Jan 1, 2001

A computer simulation of the automatic control of continuous mining machines has been prepared, similar to previous simulations of longwall mining systems and coal thickness sensors. The simulation allows for programmed variation of the horizon detection method, the azimuthal guidance system, the type and configuration of the miner, varying hardness in the unmined face material (leading to varying error in the machine heading), and the miner's cutting cycle. It simulates control of the miner in three axes. Use of the simulator makes it possible to anticipate problems arising from the complex character of underground mining, which include unpredictable multi-pass coupling and unpredictable variation in geological conditions.

Jan 1, 1993

By George Filz, Morales, Carlos, Bertero, Filippo Maria, Alessandro, Leoni

"The Deep Mixing Method (DMM) represents a viable solution to improve adverse geotechnical properties of foundation soils for many practical applications. A pre-construction soil investigation campaign is necessary to assess soil properties and to retrieve samples of different soil layers for a laboratory Bench Scale Testing program (BST). The BST has to be designed using various binder types, binder contents, and water/cement ratios in each of the soil types. Following the laboratory program, a full scale Field Test (FT) is typically necessary to verify the results of the BST. This paper will highlight the differences and the importance of performing both pre-construction laboratory tests and field tests to ascertain the proper mixing parameters in the different soil layers. Comparative analyses and interpretations between the lab and field stages, along with accumulated information about soil properties and quality control (QC) results, allow fine-tuning the production parameters throughout a project. Three Deep Mixing Method projects, where both laboratory and field tests were executed, are illustrated: (1) The LPV 111 Project (New Orleans, LA, USA): DMM was used for ground improvement/foundation strengthening to stabilize and support the burden of a new levee raise; (2) The Rio Puerto Nuevo Project (San Juan, PR, USA): DMM was applied to improve the soils adjacent to a 90"" forced sewer main relocation and to improve the soils for the base of a new drainage channel; and (3) State Road 83 (US 331) over Choctawhatchee Bay project (Walton County, FL, USA): DMM was applied to stabilize the causeway sections of the bridge enhancement project. Data recorded during laboratory and field tests for these projects were analyzed and interpreted to select the most appropriate construction parameters to provide a final high-quality product.INTRODUCTIONThe Deep Mixing Method (DMM) represents a viable solution to improve adverse geotechnical properties of foundation soils in many situations. The effectiveness of working parameters depends largely on the physical and mechanical properties of the soil to be treated. Therefore, well designed laboratory and field test programs, aimed to disclose the interaction between the site-specific soils and the mixing parameters, are essential to achieve the desired end product.Generally a pre-construction soil investigation campaign has to be performed to assess soil properties and to retrieve samples of different soil layers for the laboratory Bench Scale Testing programme (BST). The BST has to be designed using various binder types, binder contents (or cement factors - CF), and grout water/cement ratios (W/C) in each of the soil types; the selection of the different combinations and dosages for the BST is based on past extensive experiences on similar materials. Following the laboratory programme results, a full scale Field Test (FT) has to be designed and executed, installing several DMM elements to verify the results of the BST and fine tune the construction parameters, with the appropriate binder type and dosage and the most effective equipment and tool configuration."

Jan 1, 2015

By Carl Rampacek

Laboratory and small-scale continuous pilot-plant investigations made at the Tucson Metallurgy Research Laboratory of the Bureau of Mines have demonstrated that the copper segregation process is applicable to the treatment of oxidized and mixed oxide-sulfide copper ores regardless of the gangue constituents. The process comprises heating the ore to a temperature of 750° C. with small quantities- of sodim chloride and coke to produce metallic copper, which then is recovered by flotation. Tests were made on' 23 copper ores of different types containing 0.8 to 5 percent Cu, .The copper recoveries ranged from 73 to 96 percent in concentrates assaying 10 to 62 percent Cu, depending on the grade and type of ore, The direct operating cost for a 1,000-ton-per-day furnace and flotation plant is estimated at about- $3 per ton of ore.

Jan 1, 1960

By John B. Gayle

The coking time has considerable influence on the throughput of a coke oven, and for this reason a large number of papers dealing with the relationship between coking time and the different operating variables have been published. Although all factors known to influence the coking time have been studied, agreement has not been reached on several questions.2/3 Therefore, it appears worthwhile to evaluate any data that become available during investigations of the carbonizing properties of various coals and coal blends. Because it is expected that reports covering several different phases of this problem will be forthcoming as additional data-become available, the following study of the relationship between coking time and bulk density represents a report of progress on the overall investigation of factors influencing the coking time in slot-type ovens. The practice of including coarse coal in the blend going to the ovens to obtain increased bulk densities is well known. Similar increases have been realized by adding small quantities of oil to the coal mix. Although it would appear that such procedures provide inexpensive methods for increasing the capacity of existing coke-oven installations, Ramsburg and McGurl4/ point out that this increase is possible only if the additional coal can be carbonized in the same coking time as regularly employed without using abnormally high flue temperatures. This statement is in substantial-agreement with the position of Auvil and others5/ and implies that any change in bulk density may be accompanied by a corresponding change in coking time. On the other hand, a recent review of proposed methods for calculating the time required for carbonization6/ includes a number of equations that completely ignore the effects of variations in bulk density.

Jan 1, 1954

By A. G. Eccles

"INTRODUCTIONWestern Mines' copper-lead-zinc operations are located in Strathcona Provincial Park, near the geographic centre of Vancouver Island. This park includes Buttle Lake, which flows into the Campbell River water system. The latter provides domestic water for the Town of Campbell River, approximately fifty-eight miles from the mine site.Operation of the concentrator commenced in December 1966, at which time the tailings were discharged into a small tailings pond near the plant. On May 8, 1967 Permit No. 185 was granted to the company, allowing discharge of the tailings, through a submerged outfall, to the bottom of Buttle Lake.Needless to say, the concept of operating a mine within a park, and the discharge of tailings into Buttle Lake generated considerable controversy. However, this has all but been eliminated over the years by the proven effectiveness of Western Mines' pollution control program. In 1973 this program was further upgraded with the addition of an alkaline chlorination plant. Effluent treatment by this method became necessary as a result of process modifications, and has been effective in maintaining the levels of characteristics in the tailings within the ever increasing pollution control requirements imposed on the industry."

Jan 1, 1977

By H. Polat, Q. Hu, S. Chander

"The collection efficiency of dust particles was determined in a laboratory dust chamber equipped with a water spray. Measurements were made in the presence of selected nonionic, cationic and anionic surfactants. For the nonionic and the anionic reagents, efficiency was maximum in a narrow range of concentration. The surfactant concentration corresponding to high collection efficiency was usually much below the commonly used concentration of l "", however. In comparison, much higher collection efficiency was observed for a cationic surfactant at extremely low concentrations. For delineating the mechanism of capture of dust particles, surface tension and contact angle results were used to obtain a correlation between the work of adhesion and the efficiency of collection. Such a correlation was reasonable for the nonionic surfactants but not for charged surfactants. In the latter case, electrostatic interactions between charged droplets and particles were more important, especially for the cationic reagent. INTRODUCTIONSeveral methods are used to control dust in mines. These include: ventilation, foam, scrubbers and sprays. This article is concerned with improving the effectiveness of water sprays, which are widely used to remove dust particles during continuous mining, by adding small quantities of surfactants. Water sprays produce small droplets which act as collectors of dust particles suspended in air. Sprays directed at the actual source of dust have the additional property of wetting the coal before the ·particles become airborne (Hamilton, 1974). Wetting agents, also called surfactants, arc known to play an important role in many applications where dust is a problem. However, conflicting reports exist in the literature with regard to the effectiveness of surfactants in water sprays (for a review, see Chander et al., 1988). In spite of the conflicting reports, the use of surfactants for dust control has increased over the years. In a recent study by the Bureau of Mines, a 27'6 reduction in respirable dust levels was observed in a mine test when surfactants were added to sprays (Foley, 1991)."

Mar 1, 1992

By Jerry Dolph

In September 1855, 55-year-old Noah Spencer Kellogg and his $3 jackass named Bill discovered what was known at the time as a “blow out” of high-grade lead and silver ore. The deposit was located on the side of a North Idaho mountain high above the South Fork of the Coeur d’Alene River. The ore was later assayed at 41,141 g/t (1,200 oz/st) silver. Kellogg named his discovery the Bunker Hill Lode, after the June 17, 1775 Revolutionary War battle of Bunker Hill. A thriving pioneer settlement sprang into existence around the resulting mine’s workings and was eventually— and appropriately — named Kellogg. The peak rising hundreds of feet above the mine’s adit was named “Jack-ass Peak” after Noah Kellogg’s hairy companion.

Jan 1, 1996

By J. Burns Read

IT IS the purpose of this paper to summarize, as far as possible, the metallurgical information and experience gained by the Ordnance Department, during the War, in the manufacture of artillery cartridge cases, to describe the tests to which artillery cartridge cases were put, and to summarize the knowledge and experience gained in this testing. The authors wish to acknowledge the aid given by manufacturers, army officers, and civilian employees of the Ordnance Department in obtaining these data. Artillery cartridge cases are cold drawn from circular disks punched from strips of rolled brass. The manufacture involves from 25 to 30 main operations, which are done almost entirely on a punch press. Descriptions of the operations have appeared in various periodicals and, therefore, will not be given here. After each cupping, or drawing, operation, except the last, the cases are annealed at from 540° to 650° C. (1000° to 1200°F.), to remove all the hardening stresses set up in the metal and to allow complete recrystallization. After each annealing, the cases are pickled in niter cake or sulfuric-acid solution and then washed in water to remove all traces of acid. In some instances, the cases are then immersed in a cyanide-salt solution, and afterwards rinsed in water, to remove the thin layer of copper that forms on the surface of the cases during the acid pickle. The last cold-drawing operation is followed, by the heading operation which, by flattening the head of the case on the outside, causes the metal to flow on the inside to approximately the proper finished dimensions. The mouth, or open end, is then annealed at 430° to 480° C. (800° to 900° F.) by immersion in a salt bath or by gas flames. After being washed, the cases are tapered, when they are ready for machining, inspection, and testing.

Jan 4, 1922

By K. Yamaguchi

To contribute highly efficient and environmentally conscious copper smelting process, several topics in chemistry of the continuous converting were discussed. Through the reviewing the authors' thermodynamic simulations, it is recognized that small amount and low copper content of the coexisting slag is preferable. Some discussions were added to the Takeda's diagram for Cu20-FeOx-CaO ferrite slag, and the activity curves of the constituents were derived. Thermodynamic calculations were carried out on the copper contents of the slag during the blister copper formation. The dissolution of copper in slag decrease somewhat with increasing temperature, but the effects of increasing S02 pressure and decreasing %S in copper are considerable to increase in copper content of the slag. The optimum oxygen enrichment in the supplied air, and regulation of the oxidation degree for the blister copper are important in practice. The gypsum phase separation in the calcium ferrite slag was also evaluated thermodynamically, and concluded that decreasing temperature, increasing CaO content or S02 pressure, and extensive oxidation of the blister copper tend to separate CaS04.

Jan 1, 2007

By Yoichi Takeda

Copper solubility in Si02-CaO-FeOx slag equilibrated with copper matte in 10% S02 atmosphere at 1573K was estimated. Essential parameters are activity coefficients of copper oxide and sulfide, oxygen and sulfur potentials and activity of copper in the slag-matte system. A large number of experiments provide proper parameters to calculate copper solubility in slag. A classical thermodynamic model postulating CUOO.5 and CuSo.; molecules assists in estimating copper solubility in slag. Additions of Si02 and CaO reduce copper solubility almost in any condition. Copper loss, that is function copper solubility and slag volume, in the silica saturated Si02-FeOx binary slag is minimally equilibrated with less than 66% copper matte while copper loss in the 50% FeOx-SiOrCaO ternary slag saturated with 2CaOSi02 is minimally equilibrated with over 66% copper matte. This slag composition has potential for continuous copper converting, direct copper production or high-grade matte production.

Jan 1, 2003

By L. B. Phelps

Many coal mining companies have potential surface mine reserves which either are known or suspected to have had prior drift mining activity on them. In many cases, there is no documentation on these mines or at best, very fragmented records. These undocumented abandoned underground mines are creating engineering, financial, and environmental difficulties and concerns for both surface coal mine operators and regulatory personnel. This paper examines the use of resistivity techniques in detecting entries of abandoned drift coal mines. The detection of such a drift mine entry would confirm the presence and orientation of an abandoned underground coal mine.

Jan 1, 1985

By Mohab Sabry, Emre Biringen

"Over the past decades, there has been an increasing recognition of the strategic use of pile-supported rafts in design of heavily-loaded structures to reduce total and differential settlements. However, such a hybrid foundation construction method has not been widely utilized in many countries, including the U.S., due to code limitations. In current practice, the foundation design is based on either (i) the bearing capacity of the raft supported by the subgrade soils, or (ii) solely the pile capacity. This paper addresses the potential use of such hybrid piled-raft systems, where the structural load is shared by both by the piles and the subgrade soils directly beneath the raft, in foundation design of power plant structures. The study assessed some of the characteristics of piled-raft behavior by undertaking three-dimensional finite element analyses of two raft sizes, and various pile layout patterns, including the rafts with piles distributed evenly and only in the central area of the raft. The computer software PLAXIS 3D with the Mohr-Coulomb constitutive soil model was used to facilitate the modeling of such cases. The results presented in this paper indicate how strategically locating the piles could reduce the differential and total settlements.INTRODUCTIONUnder the high applied loads coming from the superstructure, the addition of piles is primarily required to improve the factor of safety against failure when a raft does not provide adequate bearing capacity. If the bearing capacity of the raft is sufficient to carry the total load with a reasonable safety margin, then the addition of piles is usually intended to reduce the settlements to an acceptable amount. In current practice, the design process for pile-supported raft foundations conservatively concentrates on providing solely the pile capacity to carry the total structural load without taking the contribution of the raft into account. This paper addresses the potential use of hybrid piled-rafts in controlling foundation settlement of power plant structures by considering the support of both the piles and the subgrade soils beneath the raft to carry the load."

Jan 1, 2017