Search Documents

By David Estrella, Hector M. Lizama, Jhonny Carrión

"Microcel™ sparging systems were installed on one column of the molybdenum cleaner circuit and one column of the copper first cleaner circuit at Antamina. The Microcel™ system is known to generate finer bubbles than jetting-type spargers, and smaller bubbles have been associated with higher recoveries in flotation. Alternating tests were carried out on the molybdenum column, using either jetting-type spargers or the Microcel™ system. Experimental conditions of gas flow rate, wash water rate, and froth depth were tested. Use of Microcel™ decreased the bubble sizes from 2.6-2.9 mm to 1.5-2.0 mm. In addition, Microcel™ improved both unit molybdenum recovery and unit molybdenum concentrate grade. In the copper first cleaner circuit, side by side tests were carried out that compared the Microcel™ column with a parallel columns fitted with jetting-type spargers. Best results were obtained at manifold pressures of 260-290 kPa, where bubble sizes of 1.6-2.6 mm were observed. In either copper or molybdenum flotation, the Microcel™ system required only 50-60% of the gas flow used by jetting-type spargers.INTRODUCTIONAntamina is a copper-zinc mine located in the Peruvian Andes. Compañía Minera Antamina is owned by BHP Billiton (33.75%), Xstrata (33.75%), Teck Cominco (22.5%), and Mitsubishi (10%). The mine was commissioned in 2001 with a capital investment of US$2.3 billion, and has a nominal 100,000 t/d mill capacity. Mining, milling, flotation, and tailings impoundment take place at the mine site, which sits at an altitude of 4,300 m above sea level. The deposit is a polymetallic skarn ore body with intrusive phases of quartz-monzonite porphyry into Cretaceous aged limestone [Evans et al, 2005]. Ore body thickness is 100 to 150 m and has the shape of a flat-lying crescent. Copper is present mainly as chalcopyrite with a minor bornite component. Zinc is present as sphalerite. Molybdenum is present as molybdenite. Some lead, bismuth, and silver are associated with the sulphides. The deposit is currently classified into six main ore types [Dechert, 2006], grouped into two categories: copper and copper-zinc. The mill produces four concentrate types: copper, molybdenum, zinc, and lead-bismuth. Copper, zinc, and lead-bismuth concentrates are transported by pipeline down to the port of Huarmey. Molybdenum concentrates are bagged and trucked to port."

Jan 1, 2008

By M. J. Ferrante

The Bureau of Mines investigated the applicability of the freeze-drying technique for preparing dispersion-strengthened tungsten powders suitable for conversion by powder metallurgy into materials which might have improved high-temperature strength. Extruded rods from compacts of tungsten-5 vol pct thoria had at 1,650° C a tensile strength of 30,300 psi and a 10-hour stress-rupture strength of 12,700 psi, These are slightly below those measured for swaged rods of commercial tungsten-3.7 vol pct thoria. Only those tungsten-thoria dispersions containing a stoichiometric deficiency of oxygen yielded a significant strengthening effect. A low-melting eutectic formed in extruded tungsten dispersions containing either zirconia or yttria, which caused a lowering of the tensile strengths. These tensile strengths were only slightly higher than strengths of elemental tungsten made from commercial powder having a particle size of 2.4 microns (Fisher subsieve). Sheet made from this commercial tungsten had a slightly higher tensile strength than tungsten made by freeze drying, but the freeze-dried tungsten sheet had a lower recrystallization temperature, a lower ductile-to-brittle transition temperature, and a higher purity.

Jan 1, 1971

By Kyle Wagner, William Joa, Colter Angell, Catherine Johnson, Marty Langenderfer, David Doucet

The goal of any business is to seek the maximum profitability for the organization through optimization the use of resources, processes and the application of new technologies. An analysis of various case studies demonstrate that blasting can have positive impacts on the crushing and milling processes resulting in increased profitability for the mining industry (Grundstrom, Kanchibotla, Jankovich & Thornton, 2001). This paper describes the case study of two copper mines in Peru producing Cu-Mo and Cu-Au concentrates, which together with their strategic partner, have implemented a project focused on the improvement of rock fragmentation. The project was based on techniques of pattern size reduction, the use of high energy explosives and the technology of electronic initiation. Combined, these techniques were shown to have significantly impacted the efficiency of downstream processes.

Jan 1, 2019

By Jonathan Allen, Peter Radziszewski

"Stirred mill technology dates back to 1928 where the idea to use “an agitator and spherical grinding media” was presented. The year 1948 saw the successful application of DuPont’s “sand mill” for pigment grinding. Subsequent years have led to the development of different types of stirred mills spanning a number of industries that require fine and ultrafine grinding. In the context of the mining industry, smaller grain size and other mineralogical characteristics have motivated the need to grind finer. In order to address this need, the interest in stirred milling technologies has grown over the last 20 years as can be illustrated by the large body of literature published over this same period of time. The typical observation reported in the literature is that in certain circumstances stirred milling is significantly more efficient than ball milling. Despite these developments, the tumbling mills are continuing to be used in fine and ultrafine grinding applications. The main reason for this, as communicated at the Canadian Mineral Processors roundtable discussion in 2013, is that the comfort level in understanding stirred milling technologies is not at the level of that of tumbling mills. The aim of this paper is to contribute to increasing the general comfort level with stirred milling technologies by developing a better understanding of how power and energy is affected by stirred mill impellor design and mill operation. This will be accomplished by first completing an overview of the power models found in the literature followed by a general description of DEM and CFD stirred mill models as well as the insights that can be drawn from them. Finally, a generic stirred mill power model will be presented and applied to different stirred mill types in order to develop some insights into the differences between different mill types. The paper will close with a discussion on some of the challenges that these models have and how future research might contribute to overcoming them."

Jan 1, 2014

The areas of concern lay in the processing of, and the subsequent hearing into, Waihi Gold's resource consent applications to extend Martha Mine. The proposed amendments to the Resource Management Act 1991 might see the introduction of contestability in the processing of applications - which would have assisted Waihi Gold; and the use of commissioners to hear the applications, with a right of appeal to the Environment Court on points of law only. It is also proposed to have major applications heard directly by the Environment Court. If Waihi Gold's applications had been heard at first instance by the Court, the delays in time and associated costs would have been reduced. However a hearing by commissioners only would not have been satisfactory, there being no right of appeal against the conditions of consent, which if implemented as granted by the Councils would have had a significant impact on the costs associated with the extended project.

Jan 1, 1998

By Walter I. Paniagua

Drilled shafts and precast concrete piles were installed for the foundation of several structures in a reconfiguration project of a refinery in Minatitlan, Veracruz, in the Gulf of Mexico. The soils are alluvial deposits of flat land from the Coatzacoalcos River, which are embedded with layers of sand, soft clay, and peat. As part of a QC/QA program, load tests, both static and dynamic, axial and lateral, were performed. In this paper results of 32 axial tests are presented, in which typical load-displacement curves were measured at the top of the foundation elements; from the interpretation of these plots, data were recorded for ultimate side shear and in some cases for end bearing capacities, which are compared with the theoretical results of the final stage of the foundation design. The comparison shows that under allowable loads, side shear determines the bearing capacity of piles, even when the tip is embedded in a hard layer. Underestimation of the side shear is evident; therefore design criteria, as well as the methods used for obtaining soil parameters, should be reviewed.

Jan 1, 2007

By H. T. Kennedy, J. E. Little

An empirical equation for the prediction of the viscosity of several pure paraffin hydrocarbons and nitrogen is presented. It involves temperature, pressure and six constants of the material, and it applies reliably to both liquids and gases. The equation is similar in form to van der Waal's equation of state. For the paraffin hydrocarbons methane through r-hexane and nitrogen, an average absolute deviation of 1.9 percent was obtained on 1,006 data points described in the literature by 14 authors. When this equation is extended to complex, liquid hydrocarbon mixtures, a correlation was obtained with an average absolute deviation of 9.9 percent. INTRODUCTION Equations describing the flow of gas and liquid through porous media contain the viscosity coefficient of the fluid. If other pertinent variables remain constant, the volume rate of flow is inversely proportional to this coefficient. In dealing with condensate fluids and volatile oils, however, the compositional effects resulting from changing pressure materially affect the viscosity. The effect of compositional changes also may be significant in certain secondary recovery or pressure maintenance processes, notably miscible displacement or gas injection. Early attempts to describe the performance of reservoirs utilized a volumetric material balance method wherein gas and liquid in the reservoir were identified as produced gas and liquid at the surface. This method of analysis proved adequate for reservoirs at moderate temperature and pressure that contained gas with moderately low amounts of condensable materials. The volumetric material balance procedures for "black oil" reservoirs leave much to be desired when applied to condensate and volatile oil reservoirs because phase behavior and compositional changes are relatively more important in these cases. The alternative is a compositional material balance, which in turn, requires a correlation of properties of the reservoir fluid with composition. This paper supplies this correlation in regard to viscosity, for reservoir crude oils. REVIEW OF LITERATURE The literature contains many empirical equations describing the effects of composition, temperature and pressure on the viscosities of pure liquids and binary liquid mixtures. However, the applicability of a majority of these equations is limited to very low pressures and to a small number of systems. Most of them, when applied to complex hydrocarbon systems, are of little value. The lack of utility of the majority of equations results from the fact that they were developed to show the separate effect of temperature, pressure or composition on viscosity, but not to predict the viscosity as a function of all three variables. And with the few exceptions noted below, they were developed to apply to much simpler systems than hydrocarbon mixtures. Eakin1 developed an equation for the viscosity of pure light hydrocarbons applicable in the gas, liquid and dense fluid regions, and in its most general form is written as µ - µo =A(ebP - e-cpk) The pure component viscosity at atmospheric pressure and temperature T, µo, was calculated using the Sutherland equation: µo = BT3/2/T + S The constants in Eakin's equation permitted the term e-CPk to become quite small at high densities (above 0.215 gm/cc), and the general equation would simplify to

Jan 1, 1969

By J Gresham, A Turichshev

Ore from Henderson’s 7700 Southwest panel cave is transported between the production and truck haulage levels through a series of orepasses. A typical orepass complex consolidates dump points from four production drifts into two long bored raises feeding into a single truckloading chute. The system typically covers a vertical extent of 200 m and a lateral extent of 90 m. In the process of commissioning several initial orepass complexes, challenges with preferential draw in the long bored raises were observed. Preferential draw occurs when one long orepass mobilises much sooner and/or flows significantly faster than the other orepass. This has negative implications for orepass availability in the production drifts. As future mining at Henderson relies on the construction and use of such orepass systems, the development of appropriate design criteria and practical solutions to existing flow problems was necessary.A series of PFC3D numerical models were developed to assist in identifying the factors influencing preferential draw and possible corrective measures. The models helped to identify two primary factors that caused the preferential effect: the relative elevation of the brow at the bottom of each long bored raise, and the location of the bin used to funnel fragmented rock from both raises into the chute. This paper covers the initial design of the orepass complexes at Henderson, results of the numerical models, mitigation work done to date on existing orepass complexes, and design criteria for future construction.CITATION:Gresham, J and Turichshev, A, 2016. Correcting preferential flow problems in long orepass systems at Henderson Mine, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 549–554 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By R. J. Sweigard, C. T. Justice, T. Beckham, E. D. Thompson, T. C. Hopkins

Fine coal refuse is often pumped, as slurry, into surface impoundments as a means of permanent disposal. As the available volume is filled, the height of the embankments are frequently increased. Many times the additional embankment material is placed upon consolidated fine coal refuse. There has been some concern about the long-term effect of consolidation of this material at or above the liquid limit upon its shear strength. A laboratory investigation was performed using three different types of fine coal sluny taken from Central Appalachian coal preparation plants. The refuse was consolidated in 10-foot plexiglass columns under incremental amounts of surcharge loading. The incremental loads were designed to simulate the effect of increasing the height of a refuse embankment on top of the consolidating coal slurry. After the refuse in the columns had consolidated for several months, the columns were cut apart and triaxial tests were performed on both the consolidated material and unconsolidated material for comparison of their shear strength parameters.

Feb 24, 1997

By W. C. Winegard, A. Galibois, C. J. Beingessner

The effects of solutes on the distribution of two-dimensional configurations of grains in zone-refined tin have been studied. When solutes with partition coefficients (ko) greater than unity are added, three-sided pains become more prevalent and the growth law changes. It is shown by electron-Probe micro-analysis that a solute buildup occurs ahead of a moving grain boundary when ko > 1. It has been found recently1, 2 that solutes with partition coefficients greater than unity have a larger retarding effect on grain growth than solutes with k, less than unity. ko is defined as the ratio of the concentration of solute in the solid to the concentration of solute in the liquid with which the solid is in equilibrium. Niessen and winegard2 have suggested that this effect is probably due to the complex shape changes which occur during the process of grain growth and that no theory based on single boundary motion3-5 can explain the results. They suggested that the dissociation of the unstable fourfold junction was delayed in alloys where ko was greater than 1 because the boundaries at the junction had to move into a region of high solute concentration. If indeed this mechanism were correct, it was felt that not only would the dissociation of fourfold junctions be affected by the solute buildup ahead of the boundaries, but the collapse of three-sided grains would be impaired. These combined effects would naturally lead to a modification in the distribution of the number of sides per grain seen on a two-dimensional section. The present investigation was undertaken to test these hypotheses by examining the grain-growth process in detail. EXPERIMENTS The Distribution of Grain Configurations in Zone-Refined Tin as Seen on a Two-Dimensional Section. Following the method of Bolling and Winegard,6 zone-refined tin was cast into button-shaped specimens and, subsequently, plastically deformed under a drop hammer at room temperature. The resulting flat coin-shaped samples were annealed at 200°C, some for 50 sec and others for 100 sec. The specimens were then examined to determine the distribution of the number of sides per grain, i.e., the num- ber of crystals adjacent to any particular grain in the section. For simplicity, the grains were classified as three-sided, four-sided, and so forth; this concept is schematically illustrated in Fig. 1. As indicated by smith,' it was necessary to examine every grain within an enclosed area to obtain a proper distribution of the relative frequency of each type. The distributions for the two annealing times are illustrated in Fig. 2. The total number of grains examined is also indicated on the figure. It is evi-

Jan 1, 1965

By Guo Junfeng

The strength of coal mass saturated with gas is an essential parameter in studying the mechanism of gas and coal outburst, and its prediction method. Up to now, there has not been a method for determining the strength of coal mass saturated with gas. This paper describes a new method whereby the strength of in-situ coal mass can be determined and stored continuously and automatically. The simulation results obtained in the laboratory indicate that the new method allows a fast, reliable, inexpensive and convenient determination of the strength of coal mass.

Jan 1, 1992

By Kwangmin Kim, Junnhyeok Park, Taehee Lee, Minkyu Kim

Mine tailings storage facilities (TSFs) can be a significant source of fine, respirable dust. This dust poses concerns, especially for nearby communities, because of its detrimental impact on respiratory health. To address these concerns, this study examined the effectiveness of commercially available polymers, known for their biocompatible and environmentally friendly features, to prevent dust generation from upstream-type TSFs in active mining operations. It focused on two areas in TSFs: the tailings beach and slope/dike surfaces. Two types of polymers—polyethylene glycol and poloxamer—were selected, and their effectiveness was evaluated in a series of phased laboratory and field tests. The lab tests investigated the moisture-retention capacity of the tailings after treatment with the polymer solutions as well as the ability of these solutions to reduce dust emissions. Polymers were applied to a tailings bed surface in the lab and dust was generated from this surface using a wind tunnel. PM10 and PM2.5 concentrations were measured using laser-diffraction dust sensors, and the polymers were found to have reduced dust emissions up to 95%. Small-scale wind-blowing tests were conducted in the field (specifically, in a controlled environment at a TSF) to evaluate polymer effectiveness on the tailings beach and slope/dike areas. The tests revealed that the AP could efficiently suppress approximately 80% of PM10 and PM2.5 dust emissions at both types of areas. Finally, 1000 gallons of AP solution were discharged at the top of tailings beach and slope/dike areas, respectively, and found to be effective. The results of these tests showed the high potential of the biocompatible polymers to be a feasible solution for reducing the respirable dust emissions from upstream TSFs in arid and semi-arid regions.

By Kwangmin Kim, Junnhyeok Park, Taehee Lee, Minkyu Kim

Mine tailings storage facilities (TSFs) can be a significant source of fine, respirable dust. This dust poses concerns, especially for nearby communities, because of its detrimental impact on respiratory health. To address these concerns, this study examined the effectiveness of commercially available polymers, known for their biocompatible and environmentally friendly features, to prevent dust generation from upstream-type TSFs in active mining operations. It focused on two areas in TSFs: the tailings beach and slope/dike surfaces. Two types of polymers—polyethylene glycol and poloxamer—were selected, and their effectiveness was evaluated in a series of phased laboratory and field tests. The lab tests investigated the moisture-retention capacity of the tailings after treatment with the polymer solutions as well as the ability of these solutions to reduce dust emissions. Polymers were applied to a tailings bed surface in the lab and dust was generated from this surface using a wind tunnel. PM10 and PM2.5 concentrations were measured using laser-diffraction dust sensors, and the polymers were found to have reduced dust emissions up to 95%. Small-scale wind-blowing tests were conducted in the field (specifically, in a controlled environment at a TSF) to evaluate polymer effectiveness on the tailings beach and slope/dike areas. The tests revealed that the AP could efficiently suppress approximately 80% of PM10 and PM2.5 dust emissions at both types of areas. Finally, 1000 gallons of AP solution were discharged at the top of tailings beach and slope/dike areas, respectively, and found to be effective. The results of these tests showed the high potential of the biocompatible polymers to be a feasible solution for reducing the respirable dust emissions from upstream TSFs in arid and semi-arid regions.

This paper investigates the effects of solids concentration and the addition of Dispersant S40 on the flowability of original and ground limestone slurries. A rotational viscometer with a concentric cylinder geometry and a controlled-stress rheometer with a cone-and-plate geometry were used to characterize the rheological behaviors of limestone slurries. The rheological behavior of original limestone slurries (<100 µm) is transformed through different types of flows with increasing solids concentration. The use of Dispersant S40 can improve the slurry flowability by decreasing viscosity and eliminating Casson yield stress. It is therefore used as a grinding aid for the wet ultrafine grinding of limestone. The rheological behaviors of ground limestone slurries vary with grinding from a starting dilatant flow-ability to a resulting pseudoplastic one with an evident Casson yield stress in combination with a thixotropic character. The appearance of pseudoplastic flowability combining thixotropy is related to the fineness of a ground product and its specific surface area, which are both correlated to solids concentration and the additive amount of Dispersant S40. In addition, the accurate rheological characterization of time-dependent fluids is dependent on the instruments used and operation conditions.

Jan 1, 2007

By K. V. Phani Prabhakar, G. Padmanabham1, L. Subashini

Laser-arc Hybrid Welding (LAHW) is a relatively recent concept which effectively combines the advantages of laser welding such as the high depth of penetration, low heat input, high welding speed and the positive aspects of arc welding such as better edge bridging and possibility to add filler. For example, steel sections upto 12 mm thickness have been successfully welded in a single pass at a welding speed of 1 m/minute using a 3.5 kW CO2 laser in combination with a MIG arc. Maraging steel of grade M250 is widely used in the aerospace industry in thicknesses upto 10 mm. Conventionally, it is possible to MIG weld such thicknesses in 3-5 passes employing V-Groove joint preparation. However, this multi-pass welding results in formation of reverted austenite in the weld zone after post weld aging; and the high heat input widens the reverted austenite containing heat affected zone which is popularly known as the dark zone/eyebrow zone. Both these zones are detrimental to strength of the welded joint, specifically the fracture toughness. The width of the dark band is an important factor because, thinner the band, it is supported more effectively by the surrounding material. Therefore, in order to avoid multi-pass welding and reduce the overall heat input, single-pass laser-MIG hybrid welding was attempted on 10 mm thick maraging steel M 250 plates using a hybrid laser arc welding system comprising a 3.5 kW CO2 slab laser and a MIG welding system. Simultaneously, multi-pass MIG welds also are produced. Both the laser-MIG hybrid and MIG welds are characterized microstructurally and subjected to mechanical tests such as tensile and fracture toughness in as-welded and post weld aged condition. The amount and distribution of reverted austenite in the fusion zone and width of the dark band was found to be different. Hybrid welds showed a narrow dark band zone and improved mechanical properties. Laser-hybrid and MIG welding investigations carried out on thick section maraging steel M 250 will be presented in detail, including microstructure, tensile properties and fracture toughness of the welds. To the best of the knowledge of the authors there are no reports on laser-MIG hybrid welding of maraging steels.

Jan 1, 2014

By Rolando Gonzalez

Mexico’s role in the world economic community continues to grow. And it is important that the country makes use of its natural wealth, including its large underground deposits of minerals and metals. With that in mind, Industrias Peñoles S.A. de C.V.(Peñoles), a mining, smelting and refining company, began mining lead, zinc and other metals from the Francisco I. Madero Project (FIM). The mine is located about 600 km (370 miles) northwest of Mexico City in the state of Zacatecas. Peñoles plans to remove about 3 Mt/a (3.3 million stpy) of ore from FIM. To achieve this goal, the company needs to optimize its processing, to maximize the amount of metal it extracts through FIM’s large flotation lead-zinc concentrator. To ensure high productivity, Peñoles and its contract engineering firm, M3 Engineering and Technology, of Tucson, AZ, have implemented anore processing system.

Jan 1, 2003

By Joseph Nawrocki, Margaret Hettinger, Dr. Catherine Johnson

"Optimized rock fragmentation is essential for minimizing downstream costs to mining operations.Photographic fragmentation analysis, vibration monitoring, and high-speed video all providemeasurements of blast effectiveness and supply data that allows operations to modify blasts to achieve downstream goals."

Jan 1, 2016

In 1801, Hatchett discovered the oxide of a new element while he was examining a heavy black mineral from Haddam, America, which had been presented to the British Museum. He named the mineral Columbite and the metal Columbium. A year later a Swedish investigator, Eckeberg, while working with a new mineral resembling columbite-yttrotantalite discovered a new element, to which he gave the name of tantalum.In 1844, Rose announced the existence of two new elements in a sample of columbite from Bodenmais. One was similar to Eckeberg&apos;s tantalum and the other was called Niobium. Wollaston, in 1909, attempted to show experimentally that columbium and the tantalum were identical, but it was soon proved that they were two separate elements. Subsequently a number of investigatiors found other &quot;new elements&quot; in tantalum and columbium bearing ores, but these were shown to be mixtures of the twin metals.Since Hatchett&apos;s Columbium and Rose&apos;s Niobium are identical, it is more fitting to use the name assigned to this element by the earlier investigator. However, the term niobium is still retained in Germany and England.The separation of tantalum and columbium has been one of the major problems for analytical chemists since the discovery of the two elements and it is only in recent years that tantalum of a high degree of purity has been produced. High purity columbium metal is probably still to be obtained.Until 1903 tantalum was merely a laboratory curiosity, but about this time its use in incandescent electric light bulb filaments was discovered. Eight years later it was replaced by tungsten, which was better and cheaper. For a time the electrolytic valve action of tantalum was used in the charging of storage batteries, but the chief uses of the metals&apos; to-day are for corrosion resistant apparatus, in vacuum tubes and as carbides in the manufacture of hard cutting and shaping tools.Most of the recent work on the metals has been done by C. W. Balke, in America. Tantalum has been studied more than columbium. OCCURRENCE OF TANTALUM AND COLUMBIUMI. NATURE OF ORESTantalum and columbium occur, nearly always together, as the oxides in combination with other metallic oxides. The only known exception to this is the reported occurrence of metallic tantalum with gold in the Ural Mountains. Unlike most other metals, no compounds with sulphur are known to occur in nature. Tantalum and columbium minerals occur usually...

Jan 1, 1943

By M. Ramström

"In 2002, Atlas Copco Rock Drills AB released the new rig control system (RCS) technology for all of its drill rig types. RCS opened the way for a new generation of computerized drill rigs based on modern, standard PC-computer technology. Drilling accuracy, information logging, reduction in manpower in some types, and serviceability have all taken a quantum leap forward when compared with previous generations of drill rigs. RCS is modularized and distributed by means of CAN-bus technology. This technology, which is well proven in automobile applications, forms the communication backbone of the rig. The modularity facilitates almost unlimited possibilities for the expansion and adaptation of drill rig functions."

Jan 1, 2005

By Wilbert J. Huff

This is the sixth of a series of annual reports describing the work of the Explosives Division, Bureau of Mines, United States Department of the Interior.3/ It deals particularly with the activities of the division from July 1, 1940 to June 30, 1941. The studies outlined in this and preceding reports of the series have been conducted under the direction of the author and the respective unit leaders, to whom specific credit is given.

Jan 1, 1942