Search Documents

By Vojtech Gall

Pre-support measures for urban tunneling have seen a substantial development in the recent past. Ground improvement techniques, pipe-arch and spiling methods now allow for non-disruptive tunneling at very shallow depths under sensitive structures, rail tracks and roadways. The paper presents experience gained on national and international projects built over the past decade that represent case histories and therefore may be used as guidance for the development of similar solutions for future tunneling projects at shallow depths. Reference projects include tunnels for the Washington, DC Metro, London Underground, Dulles Inter-national Airport, Busway tunnels in Boston and the Ft. Canning Tunnel in Singapore.

Jan 1, 2008

By Richard R. Brochu

At the International Society ofExplosives Engineers Annual Conference held in Nashville, Tennessee in February 1995, a Seismograph Standards Committee was established. The purpose of this wmmittee was to develop objective performance specifications for vibration measurement instrumentation and field use practices. It was also understood that due to geology, temperature, and moisture in the soils, it is not possible to design and build an instrument to give ‘results which are absolutely comparable for ground vibration. It was, however, considered essential to standardize instrumentation by which vibration can be measured under closely defined conditions so that results obtained by users of seismographs are always the same ,&thin stated tolerances.

Jan 1, 1998

By L. Adler

Two basic cases involved in the design of an opening in bedded rock are: 1) where the beds deflect from each other so as to be separated; and 2) where the beds deflect onto their lower neighbor, loading the latter while reducing their own load. Analysis of case 1 is relatively simple, while the interference of the original deflection curves in case 2 complicates analysis of the latter. Figures and formulae are presented for determination of interference loading in this situation. The design of an opening in bedded rock involves two basic alternatives.1'2 In one case the beds deflect away from each other, so as to be separated from their neighbors; in the other case the beds deflect onto their lower neighbor, loading it, while reducing their own load. This is shown in Fig. 1. The first case lends itself to a simple analysis, since the upper and lower boundaries of each beam remain a free surface. In the latter case, however, due to the interference of original deflection curves, the analysis is more complex. Earlier investigators of this interference problem solved it by making the tacit assumption that this type of loading was uniformly distributed along the beam's length. While there is no intuitive justification for this assumption, its use does lead to an approximate solution. Still, a more exact solution does not require this apparently unrealistic restriction. To achieve initial simplicity, the analysis will at first be limited to a two-bedded sequence, as in Fig. 2. Since both beams have identical end conditions and spans, the original deflections of their center lines are members of the same family of curves, as shown in Fig. 3. Therefore, if interference occurs at one point along their center lines, it will occur at every point. For convenience, the midspan point is that usually examined. Deflection at midspan for a uniformly loaded beam regardless of end conditions is: where c is a constant depending on end conditions; w is the body load and equals yh, lb per ft; y is the specific weight of rock, lb per ft'; L is the span, ft; E is Young's Modulus, lb per ft2; I is moment of inertia (for a rectangular section), I = bh3/12 = h3/12, (ft4); b is the width of beam and equals one; and h is the thickness of beam, ft; or 3U > yB an Substituting the appropriate values into Eq. lb, interference between the two beds can be predicted. Should it occur, the additional loads along the lower boundary of the upper bed and the upper boundary of the lower bed must be determined. From the principle of action and reaction, these added loads are known to be equal and opposite, as indicated in Fig. 4. Since the final deflection curves for both beds are identical (Fig. 3), their successive derivatives of y with respect tox must also be identical. That is:

Jan 1, 1961

By C Chambers

"AustraliaÆs mining sector faces challenges to its competitiveness; operating costs are being adversely affected as a result of volatile commodity prices and growing international market pressures.Diesel fuel-generated power used in typical remote mining projects is generally reliable and quick-to-deploy; however it is ongoing expensive operating cost.Many mines and communities in remote locations source electricity from diesel generation, and often pay over $300/MWh in fuel and carbon only (i.e. excluding CAPEX). These costs are expected to rise over time and are vulnerable to price shock events or supply chain interruptions in international markets.Solar photovoltaic (PV) and other renewables can be integrated with existing diesel units to provide a highly reliable power supply. Such renewables now provide a cheaper source of electricity while maintaining the mining industryÆs stringent reliability requirements; some renewables are now cheaper than diesel power ù supplying electricity at approximately $226/MWh.Also, significant funding and concessional rate financing have recently become available to support the development of remote solar-diesel (or solar-wind-diesel) hybrid systems, including: up to $2.2 billion of as-yet uncommitted grants through the Australian Renewable Energy Agency (ARENA) and is now seeking mining industry partners, up to $10 billion of concessional financing for emerging renewable technologies through the Clean Energy Finance Corporation (CEFC) and this commences July 2013, ongoing revenue support through the Renewable Energy Target scheme, and other regional support programs administered by various governments.This paper explores: the business case for renewables - what applications and when to consider them, the potential operating cost savings if solar was integrated, the technical challenges and common pitfalls, and how to overcome them, and the upfront investment costs and whether the site is eligible for Government subsidy programs.CITATION:Chambers, C, 2013. Off-grid solar in the mining sector - Can renewable energy reduce your operating costs?, in Proceedings MetPlant 2013, pp 71-85 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 15, 2013

By Antonio Raschillà

On the 2nd of June 2007 SELI S.p.A. started the excavation of Beles Tailrace Tunnel (Ethiopia). The new 8,07 m diameter DS Universal TBM utilized for the tunnel excavation was manufactured by SELI S.p.A. and allowed the installation of 30 cm thick concrete lining, contemporaneously with the excavation of 7,200 m of tunnel. The greatest part of the tunnel alignment was excavated in hard and sound basal-tic rocks. The paper describes the main steps of the tunnelling operations which led to a remarkably rapid excavation, with a peak production of 36 m / day and a final break-through achieved 46 days ahead of the contractual deadline. Furthermore the paper describes the work and logistic organization that was set up to efficiently perform the mechanized excavation in the very remote area of the project.

The Ocean Drilling Program (ODP) is the largest international geoscience project in the world, and the state-of-the-art drill ship, the JOIDES Resolution, is permanently at sea. Each year there are six scientific cruises (legs) which each last approximately two months. These legs are designed by geoscientists from the nineteen countries that subscribe to ODP.Australia and Canada presently share ODP membership under the banner of the AUSCAN Consortium. The benefits of Australia's involvement in ODP include internationalisation of Australian geoscience, advanced graduate training, and unique scientific investigations of the ocean floors in the Australasian region. In addition, visits to Australian ports by the ODP drill ship, the JOIDES Resolution, contribute up to $2 million per visit to the local economy. Amongst the many other aspects of ten years of scientific drilling, OOP has significantly contributed to our understanding of hydrothermal processes on the seafloor. To date, three hydrothermal sites have been drilled to date by the OOP, Snakepit (MAR), Middle Valley (Juan de Fuca Ridge) and TAG (MAR). Two more hydrothermal sites are scheduled for 1996.

Jan 1, 1995

These proceedings consist of papers presented at a Bureau of Mines Technology Transfer Seminar in September 1981 for the purpose of disseminating recent advances in mining technology in the area of premining research. The introduction and descriptive papers discuss techniques and instrumentation used in premining research for metal and nonmetal mining and shaft design and borehole control for premine planning.

Jan 1, 1982

Two outstanding features of the world's young orogenic belts are their very consistently developed suites of volcanic rocks and, it is now recognized, the rather distinctive types of mineralization they contain. Further,it is now known that these volcanic suites exhibit evolutionary patterns, and it is beginning to appear that this evolution in style of igneous activity is accompanied by a parallel evolution in style of mineralization. Specifically,podiform chromite and stratiform pyritic copper ores of Alpine ultramafic/submarine tholeiite association progressively give way to more zincian stratiform ores associated with andesites and dacites, "porphyry copper"deposits developed in quartz dioritic to dacitic plugs, and lead-zinc stratiform ores related to increasingly pyroclastic, rbyodacitic volcanism.This "coupling" is exhibited well in the volcanic arcs - the young orogenic zones-of the SW Pacific which, with tbeir abundance of youthful and commonly unmetamorphosed materials provide an opportunity for investigating, through a petrochemical approach, the possible significance of ores in the elucidation of mechanisms of lava formation. It is suggested as a working hypothesis that in the orogenic (voleanic arc) regime ores are associated with the cale-alkaline rocks because these cale-alkaline rocks are in part generated by exhalative loss, and the ores are among the manifestations of tbat loss.

Jan 1, 1978

By D. Whittles, C. J. Lea, T. X. Ren, A. Kelsey

A methodology for the simulation of methane drainage combining geotechnical modelling and computational fluid dynamics (CFD) will be described. Geotechnical modelling was used to predict the development of stress and strain due to mining. The results from the geotechnical modelling were combined with empirical expressions for the variation in permeability with stress of coal measure rocks and assumptions on fracture behaviour. This allowed the permeability, as affected by mining, to be specified in CFD simulations. Flow of methane through strata, with and without methane drainage, was then simulated to examine the effects of methane drainage.

Jan 1, 2003

The first part (lH of this work dealt with the process of recrystallization of single crystals of lead after deformation by creep, as revealed by macroscopical examination. It was shown that when recrystallization commenced, a crystal, termed the primary crystal, started to grow at the edge of the specimen and extended into the body of the specimen along the slip planes. At some stage during the growth of this crystal, other crystals appeared at the boundary of this first crystal and fragments of the parent crystal. From thispoint, recrystallization was accelerated with relatively rapid necking down of the specimen until fracture occurred.All those crystals formed after the primary crystal were given the term secondary crystals. In the present paper is given a detailed account of the orientations of the primary and secondary crystals.EXPERIMENTAL METHODThe size of the test pieces and the manner of loading were given in the previous paper (1). X-ray back reflection photographs were taken of the individual primary and secondary crystals and from them were determined the orientations. The path of the X-ray beam was perpendicular to the surface of the creep specimen.In view of the large number of photographs needed, gold...

Jan 1, 1940

The results of self potential geophysical surveys conducted over base metal prospects near Orange, Goulburn, and Wellington, N.S.W., indicate that this rapid and inexpensive exploration procedure merits wider application within eastern New South Wales, and in similar environments elsewhere.

Jan 1, 1973

By C. Musingwini

The subject of optimal planning of level and raise spacing for inclined narrow reef deposits has received intermittent attention over the years because the subject matter is inherently complex. Previous work has approached the problem as simply that of simultaneously minimizing the total excavation and haulage cost associated with the development workings. However, when level and raise spacing are altered, other factors such as productivity are negatively affected, thus requiring a delicate trade-off of contradicting planning or optimization criteria. The paper concludes that the problem is actually of the multi-criteria decision analysis (MCDA) type, contrary to traditional thinking that the planning problem is achieved solely by minimizing waste development.

Jan 1, 2010

By Bhaskar B. Thapa

The proposed Caldecott fourth bore will consist of a two lane highway tunnel along California State Route 24 near the City of Oakland. The proposed design and construction sequence for the 15-m-diameter tunnel are based on the New Austrian Tunneling Method (NATM). The initial support system incorporates combinations of shotcrete, rock dowels, lattice girders, spiles, and grouted steel pipe canopies. The final lining is cast-in-place reinforced concrete. A waterproofing membrane and drainage system are placed between the initial and final linings. State Route 24 is a lifeline route, required to be open to emergency vehicles within 72 hours after a major earthquake, defined as having a return period of 1,500 years and a peak ground acceleration of 1.2 g. Although the seismic design criteria are stringent, the design of the tunnel lining system is ultimately controlled by static ground loads in the weak rock along the alignment.

Jan 1, 2008

By Met B

IN the followmg paper an account is given of work performed by the author for the purpose of sampling a slime dam on the leases of the North Mount Farrell Co. N.L., at Tullah, Tasmania, during the summer of 1925-26.For convenience the paper is divided into sections as follows:1. THE MINE2. THE SLIME DAM3. SURVEY OF THE DAM4. BORING OF THE DAM(a) INTRODUCTION(b) 1ST METHOD(c) 2ND METHOD(d) 3RD METHOD(e) 4TH METHOD(f) GENERAL NOTES5. CONCLUSION

Jan 1, 1928

By D. Campos, J. M. Macedo, S. Chadwick

The incorporation of low cost technology transfer to increase the ability of locals to acquire and maintain long term employment are key ingredients for sustainable industrial development. Alcoa’s Alumar plant on the island of Sao Luis is the largest and most modern refinery/smelter complexes in northern Brazil. The plant has one of the most advanced Environmental, Health, and Safety management process in the aluminum industry. Technical assistance, training and financial support were made available to Alumar to address social sustainability issues. Through several programs led by employees on a voluntary basis and applying intensive and extensive training programs, Alumar has enabled local people to develop skills on agriculture and land management, wastes minimization, small business development and administration, all based on sustainable development and social responsibility concepts.

Jan 1, 2004

By K. Loutet, A. Guenkel, K. Nikolaisen

"The INCO SO2/air process was patented by INCO in 1985. Well over 80 mining operations worldwide are using this process to oxidize cyanides to cyanates in the tailings from gold, silver and copper mining operations. The sulphur dioxide (SO2) for this process can be supplied either as liquid SO2, SO2 gas or as a sulphite-based salt. The majority of SO2/air operations have used sulphite-based salts as the ‘SO2’ equivalent probably due to low capital cost. Liquid SO2 has also been used frequently, but due to concerns with safety and availability, this option is often not preferred. The solid salt sodium meta-bisulphite (SMBS) is commonly employed, but its cost is an order of magnitude higher than that of sulphur. Due to the high cost of SMBS, the increased capital cost for a sulphur-burning SO2 gas plant (green field or retrofit) usually has a pay-back of less than three years. In addition, a SO2 gas plant offers potential for significant heat recovery from the sulphur burning process. In terms of safety, the SO2 gas plant only requires the storage of relatively benign sulphur and the site inventory of SO2 will be limited to the plant gas volume. Therefore, a SO2 gas plant will not trigger the Canadian Environmental Protection Act (CEPA) E2 Regulations or the US Clean Air Act Section 112(r) accident prevention regulations, as may be the case for liquid SO2.Most existing mining operations using ‘SO2’ are gold operations, but in recent years there has been an increased interest in larger sulphur dioxide gas plants for hydrometallurgical facilities that employ leaching of cobalt/manganese minerals or precipitation of manganese/iron (e.g. Tenke Fungurume and El Boleo).This paper focuses on the production of sulphur dioxide gas generated on site and on demand for the use in hydrometallurgical processes. The capital and operational costs of a SO2 gas plant is compared to conventional process alternatives using sulphite-based salts or liquid SO2."

Jan 1, 2016

By Melvin I. Esrig

Lime Cement column stabilization of soft clay and sand in Salt Lake City, Utah and in San Francisco California is described and discussed. Stabilization permitted the construction, in a single stage, of a 14 m MSE wall on "medium" clay in Salt Lake City. It was used to mitigate the potential for liquefaction in San Francisco and to stabilize the Young Bay Mud beneath the BART extension to San Francisco Airport. These applications are described and the field measurements of performance are reported.

Jan 1, 2000

A drive, 3,500 ft long, was planned to explore mineralization exposed by diamond drilling. A rate of advance of 150 ft per fortnight, approximately double previous Broken Hill rates, was required. Subsequent to the completion of this drive its extension for a further 6,200 ft was planned to provide a main haulage way along which ore could be transported from a newly acquired lease back to the main hoisting shaft, a total distance of 13,500 ft.This paper describes the working conditions, relationships, manning and costs, and gives details of the cycle and equipment used to achieve rates up to 170 ft per fortnight.OBJECTIVEDiamond drilling from the 1,000 ft level at the Delprat Shaft section had indicated that the zone of mineralization, about 150 ft wide, which had been explored on the 1,000 ft level for a length of 2,600 ft, continued downwards with a westerly dip. The drilling results showed that within this wide zone there were arrower lenses of mineralization of possibly payable grade (see composite plan, Fig. 1).Diamond drill holes of 2,000 ft and over, particularly through heavily sheared areas of sericite schist, had been found to be costly, slow, and inadequate in testing the potential and trends of these smaller concentrations of mineralization.It was therefore decided that an exploratory drive should be advanced from the northern limit of the 1,480 ft level into the western mineralization, and that from this drive diamond drill holes should be drilled at dose intervals to outline the ore.The 1,480 ft level was chosen for the following reasons.1. It had the greatest northerly reach of the accessible levels at No. 7 Shaft section below the 1,000 ft horizon and therefore would enable the test to be made most quickly.

Jan 1, 1965

A single compartment 100 A electrolytic cell charged with AICla-KCl-NaCl at 750°C was studied during an experimental campaign of 4 months. About 10 1b of aluminium were produced in continuous runs which lasted up to 1 week. The highest cathode current efficiency determined was 80 per cent. Anode current efficiency. cathode potential, analyses of melt, sublimate, and product, and reactivity of cell materials were also recorded and interpreted in terms of the role of lower valent aluminium species in the electrolysis mechanism.

Jan 1, 1971

By J. J. Gusek

There are hundreds of passive treatment systems accepting mining influenced water (MIW) throughout the world. Some systems do not perform to design expectations while others, including volunteer systems, have successfully operated relatively unattended for decades. The primary reasons for this situation include the common misconceptions that (1) a “cookbook” approach to design is valid for a wide array of MIW chemistries and site conditions, and (2) low maintenance means “no maintenance.” Passive treatment systems for MIW are typically manmade ecosystems that are designed to handle a specific range of metal loading conditions and MIW geochemistry. Thus, when design conditions are exceeded, the suite of microbial to macroscopic ecosystems may be slow to recover or mature. This should be no surprise to designers. But when a particular system fails, it may be inappropriately attributed to the technology, not the design. This paper presents a standard “phased” design protocol that appears to work and provides examples of sub-par performance of selected passive treatment systems.

Jan 1, 2002