Search Documents

By M. J. Ferrante

Laboratory-scale tests were undertaken to examine several electrolytes for possible use in separating nickel and cobalt from products being prepared at Nicaro, Cuba. The most extensive work was done with nickel sulfate-ammonium fluoride, ammonium fluoride, ammonium sulfate, and nickel sulfate-boric acid electrolytes. All four electrolytes exhibited some selectivity for dissolving nickel carbonate from Nicaro basic carbonate used for regeneration. The nickel sulfate-ammonium fluoride electrolyte exhibited less selectivity for dissolving nickel carbonate from Nicaro basic carbonate than it did from synthetic mixtures. Ammonium fluoride leaching experiments showed that a low concentration and high temperature gave a good nickel extraction with C. P. reagents; however, this was not confirmed in tests using Nicaro basic carbonate. Electrolytic tests employing ammonium fluoride leach liquors gave no further separation, since approximately 90 percent of the cobalt was deposited at the cathode with the nickel.

Jan 1, 1958

By P. J. Baguley

The model has been developed on the basis of the observation that the partitioning behaviour of a particle is related to its calculated terminal velocity. It utilises a theoretical calculation of the terminal velocity of each particle class. This is then correlated with the observed partition data for a plant separator using empirically-derived functions of operating conditions which take into account effects such as bath turbulence, holes in drum lifters and feed arrangements. The model successfully decouples the effects of medium density and viscosity and is appropriate for any bath-type separator. The correlation between calculated terminal velocity and actual partitioning behaviour was established and modelled using data obtained from two Wemco drums treating Fe and Mn ores. The model can be used to predict the prevailing size-by-size partition curves and the separation (product grades/recoveries) given the washability of the feed and operating conditions. Simulations are used to show that, for the treatment of Fe ore, there is a maximum medium density beyond which product grades fall and that this maximum decreases as the proportion of magnetite in the medium increases. This is attributed to the dominant effect of viscosity at higher medium solids concentrations

Jun 18, 1905

By F. Tailoka

Bi was electrorefined from alloys containing 10-90 wt% Pb, together with Cu and Ag as minor impurities, in a basic cell and in a recessed-channel cell with 27.5:72.5 NaCl-PbCl electrolyte at 450-470 degrees C and 10 000-20 000 A/m2. The voltage in the basic cell was as high as 9 V, with some carryover of Bi to the cathode observed, whereas in the recessed-channel cell it was as low as 285-635 mV. Flow patterns observed in a room-temperature model indicated that the recesses provide both static liquid hold-up and good mixing of the alloy, enhancing cell performance in combination with the reduced anode-cathode distance of 0.90 mm. The purity of the resulting anode product is as high as 99.9%

Aug 1, 1995

By J. M. Davidson

The potassium mineral polyhalite (K2SO4.MgSO4.2CaSO4.2H20) found in large deposits in western Texas and southeastern New Mexico is associated with varying amounts of halite (sodium chloride, NaCl) and anhydrite (calcium sulphate, CaSO4). Although the anhydrite, because of its low solubility and slow rate of solution, is relatively inert, the halite is dissolved immediately in any process solution with which the polyhalite comes in contact. Limited quantities of sodium chloride in the liquors used for the hot extraction of polyhalite materially improve the results obtained,4 but only a very small sodium chloride content may be desired in the entering polyhalite in other procedures, such as Bureau of Mines process 75. In. all of the processes suggested for the recovery of potassium sulphate from polyhalite the control of the sodium chloride content will be desirable, if not absolutely essential to efficient operation. OCCURRENCE OF HALITE IN POLYHALITE A preliminary estimate of the amount of halite associated with typical deposits of polyhalite may be derived from drill cores, although it should be remembered that only 50 or 60 core tests have been made in the many hundreds of square miles of the Permian basin. From a mineralogical study of 41 of these cores, Schaller and Henderson6 state: In many of the sections of core that seem when viewed by the unaided eye to consist essentially of polyhalite, both halite and anhydrite are present in greatly varying quantities - with very minor quantities of clay and magnesite.

Jan 1, 1934

By L. G. Marshall

This report describes dredging and processing of sand and gravel from a glacial-fluvial deposit in the Raccoon River valley near West Des Moines, Iowa. Preliminary cleaning and separation of the sand and gravel at the dredge site with subsequent transportation to separate plants and the production and disposal of the various grades of aggregate material are also described. The geology of the deposit is summarized. A tabulated summary of costs in units of labor, power, and supplies is included.

Jan 1, 1963

By A. McGarr

The shear stress t that can be sustained by the rock mass in the environs of a mining-induced earthquake controls the near-fault peak ground velocity v of that event according to v=0.25(ß/G)t, where ß is the shear wave speed and G is the modulus of rigidity. To estimate t at mining depths, I review the results of four studies involving Witwatersrand tremors that relate to the bulk shear strength. The first and most general analysis uses the common assumptions that the seismogenic crust is pervasively faulted, has hydrostatic pore pressure before mining, and an extensional stress state that is close to failure. Mining operations reduce the pore pressure to zero within the mine and redistribute the stresses such that, in localized regions, the state of stress is again at the point of failure. Laboratory friction experiments can be used to estimate t in the zero-pore-pressure regime. Second, model calculations of states of stress in the vicinity of mining at about 3 km depth indicated the shear stress available to cause faulting near the centre of a distribution of induced earthquakes. Third, laboratory experiments combined with microscopic analyses of fault gouge from the rupture zone of a mining-induced event provided an estimate of the average shear stress acting on the fault to cause this earthquake at a depth of 2 km. Fourth, moment tensors determined for mining-induced earthquakes usually show substantial implosive components, from which it is straightforward to estimate t. These four different analyses yield estimates of t that fall in the range 30to 61 MPa which implies that near-fault particle velocities could be as high as about 1.5 m/s. To the extent that the causative fault ruptures previously intact rock, both t and v, in localized regions, could be several times higher than 61 MPa and 1.5 m/s.

Jan 1, 2002

By Nick D. Rose

The importance of structural geology in open pit slope stability is overlooked in many mining operations due to pressures to cut costs and minimize mine personnel. As a result, mine geology staff are often unable to keep up with geological mapping of the pit slopes due to other day to day production oriented tasks. In some instances, key structural controls that contribute to slope instability may not be identified until after a slope instability has initiated, at which time it may be difficult or impossible to delineate these features in the field. Even for small slopes, understanding the engineering and structural geology of the rock mass, as well as the effects of groundwater and blasting practices, are of key importance to slope stability. Two case histories are presented as examples of mining operations that experienced slope instability with little more than anecdotal information about the structural and groundwater conditions encountered during mining. By conducting field reconnaissance, simple slope stability analyses and ongoing slope monitoring, practical remedial measures were implemented, allowing continued safe mining operation.

May 1, 2002

By I F. Bell, K P. Hammerschmid

Well planned and executed environmental management plans can reduce life-of-mine operating costs and the need to deal with major environmental issues at the time of mine closure. With proper planning during the exploration, feasibility and execution phases of a project, final closure costs can be reduced. The reduction of closure costs should be considered during exploration and initial feasibility studies and when process facilities, waste rock dumps and tailings impoundments are designed. During the mining of the resource, closure cost reduction will depend on effective and efficient environmental management plans for ongoing land clearance, segregation of mine waste materials, management of mine site water and workshop wastewaters, and the establishment of progressive rehabilitation strategies. These issues are the responsibility of planning, production, technical support and maintenance personnel at an operating site. The successful implementation of environmental plans will ensure that all impacts are reduced and that closure issues with major cost implications are addressed prior to closure of the mine.

Jan 1, 1995

By Anil K. Ray

This paper discusses in situ studies conducted at an Illinois Basin room-and-pillar coal mine to evaluate the performances of three different types of bolts under similar geologic conditions. The bolt types considered were the fully grouted passive rebar (FGPR), the resin-assisted mechanical anchor (RMAB), and the fully grouted tension rebar (FGTR). During the evaluations, the three types of bolts were installed in a single entry covering a span of three contiguous pillars with almost identical geologic conditions. The performances of the three types of bolts were investigated by instrumentting the bolts prior to installation as primary supports on cycle. Additional data on roof behavior was collected with extensometers and shear meters placed near the instrumented bolts. Excluding some time lapse right after installation, the performance evaluation of the three bolt systems was based on the data collected for over a year. Based on this study, it was found that the axial loads measured in the different bolt types did not show any identifiable patterns under the prevailing geological conditions at the mine. Therefore, the assumption that active bolts must be superior to passive ones is not always valid. Even though the studied mine did not have any thinly laminated, weak rocks in the immediate roof, the passive bolts performed as well as the active systems.

Jan 1, 2012

By R. J. Brison, W. C. Bleimeister

The International Salt Company has long been interested in finding an efficient process for the removal of impurities from rock salt, and particularly from the rock salt produced at the Detroit mine. Methods which have been used previously at the Detroit mine included both hand sorting and differential crushing in a Bradford breaker with rejection of the oversize. Neither of these methods was adequately effective. The development of a new process for removal of impurities from rock salt has been described in the preceding article." Basically, the process consists of exposure of crude rock salt to radiant heating which selectively heats the impure particles. Subsequently the heated particles are removed by adhesion to a heat sensitive-coating on a conveyor belt. This method was found to be effective in improving both the quality and appearance of rock salt by the rejection of the dark, impure particles. The first commercial unit employing the new thermoadhesive method of dry separation of minerals was installed at the Detroit mine of International Salt Company in Detroit, Mich. (Fig. l). This unit was first put into operation in March 1957. The purpose of the Detroit installation was 1) to serve as a pilot plant for evaluating the process on a commercial scale and 2) to produce marketable quantities of rock salt of improved quality and ap- pearance. The design of this plant was based on the results and information obtained from a 1-tph pilot plant at Battelle Memorial Institute. DESCRIPTION OF PLANT Location: The separation plant was installed underground near the crushing and screening plant, for this was the most suitable location from the standpoint of material handling. Furthermore, ample space was availabe at this location. Because the process requires a relatively constant temperature, the uniform year-around temperature of the mine (57°F) gave an added advantage to an underground operation. Feeding: The rock salt is conveyed to a surge bin, from which it is fed to the heating unit by a conveyor. The feed-rate control consists simply of an adjustable gate at the bottom of the surge bin. The plant may be fed either No. 1 grade of rock salt (0.279 to 0.375 in.) or No. 2 grade (0.375 to 0.500 in.) with a maximum input capacity of 500 tons per 15-hour day. Heating Unit: The heating unit (Fig. 2) consists of a panel of infrared lamps suspended inside a low-speed revolving screen. The radiant-heat panel, which is curved for most effective utilization of the heat, holds 240 infrared lamps of standard industrial type, each rated at 500 watts. The position of the panel is adjustable so that it can be placed centrally over and to within 6 in. of the salt bed on the screen. The entire heat panel is suspended by rollers in ¦ R. J. Brison and O. F. Tangel: Development of a Thermo-adhesive Method for Dry Separation of Minerals.

Jan 1, 1961

THERE are certain facts that the mining industry in Australia is faced with at the present moment which may be accepted as axioms. The industry is at a low ebb, as evidenced by statistics. Metals form the basis of all modern industries, and are necessaryfor the welfare of Australia. Mining is a wasting asset. Every ton of ore extracted is one ton less which c.annot be made good, and it should be our duty to get as much profit froin that ore as possible, otherwise there is a permanent loss to the country.The metal market cannot be controlled by Australia; it is more or less an international matter. Australia has not been thoroughly prospected. There are no mines being developed that are likely to replace those which are being depleted.Our mining engineers are as capable as those in other parts of the world, and have made good where they have been given a chance. There is no one cause for the present depression; there are several, more or less, interwoven. Of course, the war has had an adverse effect, but that has only dislocated things temporarily; it upset our markets, influenced the price of metals, and affected the labour market and cost of stores. Labour troubles made their appearance before the wave of unrest swept over the world. The cause of labour discontent must be investigated, and if possible removed. As each industry has .its·own problems, miners must inquire into their special problems, as there is no sovereign remedy that will suit all cases.It is obvious that we cannot mine ore if we do not know where it is; therefore, the first thing is to discover workable deposits.

Jan 1, 1919

By N. Sano

The chromium oxide in stainless steel slags usually exists as Cr2O3. However, there is a possibility that it is oxidized to hazardous CrO3 after disposal or during use. Therefore, some technical developments to reduce chromium oxide by using a smelting reduction technique have been reported recently. This paper describes the fundamentals of the technique which have been applied to ferrochromium production and reviews the recent results in literature.

Jan 1, 2004

By Derek Ettie

"In the Hydrometallurgical processes, the presence of the so-called "crud" is a constant challenge in solvent extraction. Crud is a stable emulsion which forms along the interface between the aqueous and organic phase. The spread is influenced by the following parameters: first, wind blows the dust and impurities into the open sedimentation tanks. Second, the undissolved solids such as sand transported in the PLS causing problems in conjunction with incorrect agitator design.The crud fraction can decisively impact the efficiency of the hydrometallurgical extraction because the phase interface can constitute a large fraction and the sedimentation tanks cannot react flexibly to it. In the downstream process of the series-connected sedimentation tanks, they are thus all contaminated with crud. At the same time, the necessary mass transport is significantly impeded at the phase boundary between organic phase and aqueous phase due to the crud formation.The transfer of the organic phase into the electrolysis cell can result in a "burnout" of the cathode. The carryover of this electrolyte into the extraction can cause problems with the pH regulation. The carry-over of the organic components into the raffinate also leads to contamination of the leaching circuit. The continuous treatment of the crud with a 3-phase decanter centrifuge is extremely effective in combating this problem. This technology splits all three phases from each other and they are consequently continuously separated. All subsequent process steps exhibit a stable, uniform effectiveness. The main advantage for the customer is that fluctuations in the process are eliminated and the organic phase can be recirculated back to the extraction. The recycling of the solvent alone justifies the investment in less than 6 months as examples from South Africa and Chile show.To operate solvent recovery in daily operation fully automated online at the optimum limit, the decanter centrifuge is equipped with a concentration-dependent pond adjustment called DControl® by this means, we can guarantee our customers the maximum possible solvent recovery and minimize the solvent costs in this process step. This system is presented in detail in this paper."

Jan 1, 2014

By Robert Hopler

A blast caused the destruction of a bridge and loaded freight train and the death of three men, near Chattanooga, Tenn., on May 16, 1907. The blast and its disastrous effect has been described by Mr. Hunter McDonald, M. Am. Soc. C. E., in a paper read before the Engineering Association of the South and reprinted in the Proceedings of the Association for April-June, 1907. The excessive damage was so largely due to coincidence and wreckage of the bridge and train so complete that the incident is worthy of notice.

Jan 1, 2008

By G. Hangone

Paper written on project work carried out in partial fulfilment of MSc thesis This paper investigates the effects of thiol collectors: xanthates, dithiophosphates, dithiocarbamates and mixtures of these on the froth flotation performance obtained with a bornite-rich copper sulphide ore from Okiep Copper Mine with a feed grade of 1.8%copper. Batch flotation tests were used to assess the performance in terms of mass-water recovery, sulphur grade-recovery and copper grade-recovery relationships and the Klimpel rate constant for copper recovery. The results showed that the di-ethyl-dithiocar-bamate (di C2-DTC) was the weakest collector of copper sulphide minerals. Highest copper recoveries were obtained with the di-ethyl-dithiophosphate (di C2-DTP), which were accompanied with more watery froths and lower copper grades demonstrating frothing properties in addition to collector action. Superior copper recoveries were obtained with the 90% ethyl xanthate (C2-X):10% di-ethyl-dithiophosphate (di C2-DTP) and 90% ethyl xanthate (C2-X):10%di-ethyl-dithiocarbamate (di C2-DTC) collector mixtures compared to that obtained with ethyl xanthate at an equivalent collector dosage of 0.139 mol/ton ore (a dosage equivalent to 20 g sodium ethyl xanthate per ton ore). A superior copper grade was obtained with the 90% ethyl xanthate: 10% di-ethyl-dithiocarbamate collector mixture at a dosage of 0.0695 mol/ton ore compared to that obtained with ethyl xanthate at the same equivalent dosage. Keywords: flotation, collector mixtures, copper sulphide ore

Jan 1, 2005

THE Yallourn chimney has aroused interest, as it is, for the time being, the tallest structural erection in Australia. Its height was not decided on, however, with the object of breaking records, but is purely incidental to the purpose which it serves. Theboiler plant at the briquetting works (first instalment) consists of five Babcock and Wilcox land-type water-tube boilers, each of 4510 sq ft. heating su:r£ace and 225 sq. ft. grate area in the form of step grates. Four boilers will normally produce 73,000 lb. of steam per hour at a gauge pressure of 265 lb. and a temperature of 6500 F., the fifth boiler being a reserve. Each boiler will consume about 100 tons of Yallourn coal per 24 hours. Provision is made for future installation of economizers, should it be found desirable. Designing for this condition, and allowing for a waste gas temperature of 3500 F. and an air temperature exceeding 1000 it was found necessary to have a draft of about 1.3 in. (water gauge) at the base of the chimney, and to deal with about 2000 cub. ft. of gases per second. Estimates were made of the cost of providing the necessary draught by means of fans and by means of a tall chill).ney. The annual charges of the two methods differed only slightly, and the tall chimney wasselected as being the more general practice in briquetting factories.Estimates were prepared for brick and concrete chiIlllleys. Yallourn bricks at that time were hand-made, and, while very suitable for domestic work, were not capable of withstanding high compressive stresses. The chimney design to suit these bricks thus required to be on very ample lines, resulting in high cost. Machine-made bricks from Melbourne would cost about £5 10s. per thousand on the site, with extra for radials, so that high cost again resulted. On the score...

Jan 1, 1924

By M. Andrews, B. J. Göhre, G. Strong, C. Terblanche

Mechanized mining can be experienced as a symphony by substituting the instruments for the different machines that each perform their own function and thus have different sounds. The drill-rig is the soloist around which all the other machines must play their part in harmony. Each machine can function on its own, but productivity is achieved only when all of the machines function in a holistic manner, as the different sounds of instruments form a symphony when playing together. To produce a symphony is to have the ability to put together all the pieces. It is the capacity to synthesize rather than to analyse. Today?s managers have to apply this harmonic way of thinking to make the system of mechanized mining work. In other words each of these people must have the ability of a conductor, whose job involves corralling a diverse group of notes, instruments and performers, and producing a unified and pleasing sound. At Modikwa Mine the introduction of the MAPS (Mine Activity Performance System) has allowed management to obtain a clear view of all the activities associated with the equipment. Through synthesis the issues that hampered productivity were identified and addressed to improve production and reduce costs.

Jan 1, 2006

By K. Blaski

his paper reports an investigation aimed at optimizing the compaction of granulated hard-metal powder for the production of cutting tool inserts. The optimal compaction is that which yields optimal shrinkage during sintering, i.e. minimum porosity in the sintered part. Extensive compaction tests on 23 different hard-metal powders have been carried out and have shown that the ideal ?green density? of a hard-metal compact, i.e. the density after compaction, increases linearly with the apparent density of the powder. On the basis of this result, an equation has been derived, which allows one to predict the optimal shrinkage that a hard-metal compact undergoes during sintering once the following data are known: the required sintered density, the volatile content of the powder and the apparent density of the powder. Since these data are available to the tooling designer, this equation allows one to design tooling for the compaction of hard-metal, which leads to optimal shrinkage

Jan 1, 2007

By M. van Biljon

The possible closure and subsequent flooding of South Deep Gold Mine?s neighbouring Randfontein Estates Limited No. 4 Shaft (REL 4) necessitated the construction of five concrete plugs in the connecting tunnels to prevent the ingress of groundwater into REL4 from flooding South Deep mine. Several technical investigations had been carried out before and during construction of the plugs in order to reduce the probability of groundwater flow through the boundary pillar between the two mines or through the rock mass immediately around the plugs. This paper describes the geological, hydrogeological and stability investigations carried out to evaluate the structural competence of the boundary pillar.

Jan 1, 2006

Measurements from an old survey are being machine processed as a pilot project in the development of a computer-assisted method of structural mapping in shield areas. The key element in the system is a field data sheet which requires the geologist to determine a textural hierarchy in each exposure. The pilot system is limited to orientation analysis and utilizes a prior textural analysis, but this would not usually be a problem in utilizing the system ab initio for exploration. A data processing system of this general type offers promise of considerably increased productivity of field geologists by reducing compilation time and improved technical supervision through centralization of processing, and would make structural analysis an economically viable tool in mining exploration and development.

Jan 1, 1969