Search Documents

By F. E. Brantley

Research was undertaken by the Bureau of Mines to assess the technical feasibility of smelting cement-copper precipitate in an electric furnace to produce commercial-grade copper. The blister-grade copper produced in smelting was refined by gaseous oxidation and reduction methods to rive a product equal in quality to fire-refined copper. The cement copper used in the study was typical of the material produced in commercial operations. The sample product was received in a partially oxidized state and analyzed 77.5 percent Cu, 3.4 percent Fe, 0.8 percent Pb, 0.05 percent Ni, 0.6 percent Sn, and 0.9 percent S. Smelting tests were made on the precipitate using laboratory-size induction and electric-arc furnaces. Three types of furnace linings were tested during, the investigation: Carbon, including graphite; clay-graphite; and silicon carbide. Although all proved satisfactory, either carbon or graphite was preferred because of their superior refractory properties and low permeability to molten copper. Copper recoveries in the induction and arc smelting tests averaged 92 percent in commercial-grade metal assaying 99.8 percent copper. Refining the molten copper by oxidation and gaseous reduction or by chlorine lancing increased the purity to plus 99.9 percent.

Jan 1, 1961

By Ernest J. Conway

Seventy-four human factors research and development projects were identified for possible Bureau funding. The projects were based on (1) literature surveys, (2) reviews of accident statistics and reports, (3) interviews with equipment manufacturers, MSHA, and Bureau personnel, and (4) site visits to 26 mines. The projects are divided into the following categories: those related to (1) mobile equipment, (2) maintenance shops and areas, (3) plants and mills, (4) organizational factors, (5) safety programs/data, and (6) training. The projects were rated by industry and MSHA people in terms of benefit to the industry. Projects were placed into three categories of priority. The highest priority contained 25 projects with 26 in Category 2, and 23 projects in the lowest category.

Jan 1, 1982

By Paul Meadows

This Bureau of Mines report presents operating practices and results of pressure maintenance and secondary recovery by water injection or by water injection supplemented by gas injection. Particular emphasis is placed on the results of water injection, which is the principal oil-recovery method employed in projects covered by this report. No attempt is made to study gas-injection projects or operations that are considered water-disposal projects. Also, this report does not include water-injection projects that have not been in operation long enough to evaluate results. Figure 1 is a map of north Louisiana showing the geographical locations of the projects included in this report. Most of the data used in this study were supplied by unit operators, operating companies, and the Louisiana Department of Conservation. Reservoir information and recovery data are generally those supplied by the operators, but include revisions where deemed necessary.

Jan 1, 1962

By Martin J. Kenwright

Within the famous Harrods department store, a new lift shaft has been constructed, servicing a depth of 22m below ground level as well as the existing 6 storeys of the store. The shaft will connect with a new goods tunnel which is to be excavated beneath the shop, as well as new floor space above ground level which has resulted from the infilling of a previously existing lightwell within the store. The construction of the deep shaft while maintaining uninterrupted use of the store by the Client led to a number of innovative solutions being undertaken. Empirical assessments were made of settlements anticipated from the construction process, which took place within a congested environment of existing foundations. Various elements were designed and installed to mitigate the effects of the inevitable ground movement on the surrounding overlying structure, which supported sensitive high quality finishes and mechanical and electrical installations The reinforced concrete lining of the shaft was contained within a cofferdam of minipiles. The minipile placement accuracy (1 in 150) was vital as it could not interfere with the subsequent tunnelling works. As the scheme progressed this became even more critical since the minipiles were needed as support for parts of the permanent works This paper describes:- the high quality placement and control of the minipiled cofferdam, the methods employed in assessing ground movements and the techniques used to mitigate against the effects of these movements.

Jan 1, 2000

By H. Boghosian

This paper presents the design and construction of a deep basement in a steeply sloping site in glacial till in Glasgow city centre. Existing foundations, adjacent structures and services, in tandem with asymmetric loading, presented particular challenges in the planning, execution and design of the project. The construction methods and temporary works, analysis by the Finite Element method and monitoring carried out are all described.

Jan 1, 2006

After the Loma Prieta Earthquake, which caused major damage to viaducts in the Bay Area, the California Department of Transportation set up a test programme for foundation piles. Funderingstechnieken Verstraeten B.V., beter known as Fundex, was approached, since one of the piling systems of Fundex, named Tubex, is extremely suitable in areas sensitive to earthquakes and we were very much interested to prove the capabilities of this piling system. Equipment For the installation of Tubex and Tubex grout-injection piles special piling equipment is required. Since our company is not only a contractor, but also a designer and manufacturer of piling equipment, all special equipment for our range of foundation techniques is designed and built by our own piling equipment department. For the installation of both Tubex piles and Tubex grout-injection piles for the Caltrans test programme, the following pieces of equipment were selected: a) Fundex F12 piling rig b) Drill table c) Hydraulic powerpack d) Grout mixing unit and high pressure pump

Jan 1, 1993

By E. Swart

The purpose of this paper is to provide an overview of the current legislative framework for mine closure within South Africa as well as the new requirements in terms of the Mineral and Petroleum Resources Development Act, 2002. The roles and responsibilities of Government, the mining industry and other stakeholders and confusion caused are also highlighted.

Jan 1, 2003

OWING to the gradual depletion of the hitherto plentiful supply of firewood in the immediate vieinity of Queenstown and Gormanston, which caused a steady increase in the cost of fuel for domestic purposes, the Mount Lyell Company took steps several years ago to make available as a substitute electric current from its Lake Margaret hydro-electric supply. In order to make this practicable it was necessary that the cost of electric power for heating purposes should compare favourably with the cost, of fuel, and the installation of domestic appliances brought within reach of the average householder, and efforts have been continuously directed towards this end since the year 1928.WATER HEATERSThe installation of electrical apparatus in local dwellings began with hot-water services, the heating elements being the types then procurable on the market and adapted to meet requirements.These, however, did not prove satisfactory, but the study of their bilure resulted in a type being developed locally which has overcome all difficulties. The first type of water heater evolved was an outside circulation one the element of which consisted of an iron pipe through which the water passed, insulated with micanite and wound with nichrome wire, the latter being covered with alundun cement to keep it in position and prevent oxidation. This was insulated on its outside surface with a layer of asbestos flour, and connected to the hot-water container as shown in Fig. 1. It was found, however, that the iron pipe had a short life, due to a certain amount of acidity in the water, and a copper pipe was substituted which proved very durable. Some heaters with this improved type of element are still operating after six years of use. The resistance wire is run at a very low current density, which ensures durability.

Jan 1, 1927

By W. M. Jansen

In many mineral processing operations, the reported production figures for an accounting period may not make the best use of available data. While most of the mathematical approaches, such as check-in/check-out, mass balancing, used in effective metallurgical accounting strategies are well understood, the sources and magnitude of measurement errors generally are not. As part of the 'AMIRA P754-Metal Accounting and Reconciliation' project, a study was undertaken at the Northparkes copper/gold concentrator near Parkes, New South Wales to examine the data used in their concentrator metallurgical accounting system. This paper summarises the results of a detailed examination of the mass measurement systems around the concentrator as well as the primary sampling system used for grade estimation. The goal of this work was to develop practical techniques to quantify the error (ie both accuracy and precision) of the measured metal accounting information. With this information, statistical confidence levels for this data can then be calculated. If the errors are small, the effect of error in each piece of measured data can then be propagated to other calculated production figures such as recovery and feed grade using a statistical technique called `the propagation of error'.

Jan 1, 2007

The pressure of low commodity prices forced the design process for the second lift of Northparkes E26 Mine to adopt a continuous improvement philosophy. The emphasis was to minimise capital expenditure while still maintaining the excellent low operating costs achieved on Lift 1. Although the first block cave lift at Northparkes is the most productive underground mine in the world and is held up as a benchmark for the use of technology in mining, areas for improvement were identified. Every area was critically assessed and investigated for the possible application of new techniques and technologies. Key learnings from the construction and production phases of Lift 1 were captured, documented and used as the starting point for the Lift 2 design. This paper shows how and why the design parameters initially used onLift 1 were changed to become the current E26 Lift 2 developmentproposal. The main differences between the two block caves arehighlighted. The alternative techniques and equipment that wereconsidered are also discussed. * Originally published in the Proceedings of MassMin 2000,published by The AusIMM.

Jan 1, 2001

By K. D. Mills, R. G. Robins, C. G. Anderson, L. G. Twidwell

Arsenic is a metalloid which has attracted great environmental scrutiny in recent decades. Moreover, its control and deportment is becoming increasingly important in the metallurgical processing of modern complex ores and concentrates. As such the authors of this publication have a combined professional experience of well over 100 years in the study and hydrometallurgical treatment of arsenic. Hence, this paper will cover arsenic fundamentals along with a review of technology for removal, fixation and stabilization. Finally, an application of industrial Alkaline Sulfide Leaching (ASL) of a copper enargite concentrate will be elucidated.

Jan 1, 2014

Using DEM to Model Industrial Banana Screens

Sep 13, 2010

By Debasis Deb

The first version of the longwall strata control and maintenance system (LSCMS) has been successfully developed by the Strata Control Re¬search Team at the University of Alabama. The system includes a software package designed to monitor shield leg pressure, interpret the data and predict the forthcoming roof loads and the existence of geological anomalies. It can also detect maintenance problems of the face equipment. The LSCMS was installed underground and connected to the surface terminals at Drummond's Shoal Creek Mine in Alabama. The system has proven to be a useful and practical system for improving safety and efficiency in coal-mining operation. The Shoal Creek Mine is a new, large coal mine operated by Drummond with two longwall panels. The Blue Creek seam is the primary source of coal production. It is located at a depth of 275 to 440 m (900 to 1,450 ft) below the surface with an approximate 2% southwest dip. Typical strata conditions are represented by two stratigraphic columns (Figs. la and b). A fireclay/dark shale parting (called Middleman) 0.2- 0.7-m- (1- to 2.5-ft-) thick exists between the Mary Lee and Blue Creek seams. Mining conditions vary from area to area. This mainly depends on the Blue Creek seam thickness that ranges from 0.9 to 2.9 m (3 to 9.5 ft). The thickness of the Mary Lee and the parting is relatively consistent with a to¬tal of 0.9 m (3 ft). They are mined when the Blue Creek seam becomes thinner. In most of the panels, the immediate roof is composed of sandy shale 1.5-

Jan 1, 1997

By D. G. Westlake

Levine has concluded that prismatic slip in titanium is controlled by two distinct thermally activated processes in the temperature ranges O° to 220°K and 220" to 300°K. We feel that his evidence is not convincing. He has drawn a curve through the plot of activation volume u* vs temperature T with a break at 22WK, Fig. 2. We believe that considering the possible experimental error apd the fact that there are only four points between 4° and 196°K, one could be justified to represent these points by the smooth curve we show as a solid line in Fig. 12. Levine believes that (8rf/aT)+ is discontinuous at 220°K, but he hints that he recognizes the possible doubt. We doubt seriously that the results shown in Fig. 1 indicate a discontinuity at 220°K. Certainly if he were justified in drawing a straight line through only four points on Fig. 2, we are even more justified in drawing straight lines through the seven points between 77" and 297°K on Figs. 1 and 3, because a straight line touches all seven of his circles. If his measurements of t were so precise that his decision to draw two curves in Fig. 3 is valid, then the experimental technique is deserving of further mention. We have drawn a smooth curve through the results in Fig. 3 and used this and the curve in Fig. 12 to obtain the values of shown in Fig. 13. Finding continuous is a contradiction of Fig. 4, which deserves comment itself. Levine obtained the solid circles in Fig. 4 using Fig. 2 and a smooth curve through the points shown in Fig. 3. We have replotted these solid circles in Fig. 14. We submit that there is no basis for his two straight lines (dashed in Fig. 14), and therefore have superimposed the curve that we believe is indicated. Certainly, there is reasonable doubt that a discontinuity in dH/dT exists at 220°K, even when one accepts Fig, 2. Furthermore, if one draws the straight lines indicated by least-squares treatments of the results presented as open circles in Fig. 4, their intersection is at about 196°K, not at 220°K as shown. Thus the alleged agreement between Figs. 3 and 4 with respect to "break" temperatures is not apparent. In Fig. 9, Levine has drawn a straight line very much different from the one indicated by a least-squares treatment. Obviously, he has done this because he recognized that H = 0 when T = 0. He is consistent in drawing the low-temperature curves in

Jan 1, 1968

By G. Tranell, L. Kolbeinsen, S. Gaal, J. Safarian

The effect of carbon material properties on the rate of MnO reduction from ferromanganese slag by solid graphite was investigated. A sessile drop technique was used to study the reduction rate of a synthetic slag containing 45 wt% MnO at 1500 and 1600 ºC. Different types of graphite substrates were used and the con-tact angle between slag droplets and substrate were measured in-situ. Moreover, the slag droplet volume during the interaction with the graphite substrates was calculated and normalised. The mathematical relationship between the slag density during the reduction and the normalised slag droplet volumes during the reduction were derived and the MnO reduction curves were then calculated. A method for measuring the slag reactivity of solid carbon was defined and used to qualify the propensity of the different graphites to react with the liquid slag. Some supplementary studies such as manganese evaporation measurement and EPMA analysis for determining the extent of MnO reduction were also carried out. It was observed that there is nota significant difference in the wetting angle of the graphite substrates by the slag, and the wetting is not changed within the temperature range of 1500-1600ºC. However, the changes in the contact angle during the slag reduction at 1600ºC are more than at 1500ºC. The kinetics of MnO reduction is dependent on the type of graphite and it is more dependent on the graphite properties at lower temperatures. On the other hand, the dominant properties of graphite on the reduction rate vary with temperature. A multivariate analysis on the graphite properties and the parameters related to the slag reactivity indicated that the kinetics of MnO reduction is mainly dependent on the temperature, and then on the graphite properties. It was also found that at1500 ºC the surface area and the CO2 reactivity are the most important graphite properties for the slag reduction, suggesting that the reactivity of carbon is rate controlling at 1500 ºC. However, the porosity related parameters are the most important graphite properties at 1600 ºC, suggesting that CO gas desorption is rate controlling at high temperatures.

Jan 1, 2007

By Scott D. Thomson

The client for this project specializes in the use of state-of-the-art technology to fabricate and assemble composites and metal-bonded structures for commercial and military aircraft programs. One of the key components for this operation at the client's plant is a highly precise computer-numerical-controlled router known as the Shoda Machine. This machine tool was installed at the plant in July 1998 for the manufacture and inspection of aircraft parts, and it is extremely sensitive to deflections. To monitor the occurrence of deflections, an internal laser system continuously checks the machine calibration. Deflections in excess of 5/1000-inch in the foundation on which the machine rests require costly periodic re-leveling and recalibration of this tool. Therefore, a significant problem arose when measured deflections during machine operation were as large as 20/1000-inch. In addition, the foundation was cracked in at least three places as a result of elastic foundation movement caused by dynamic loading as well as shrinkage and loss of base support. Deciding on a remediation procedure to alleviate or eliminate these problems involved the following important considerations: (1) achieving the client's need for reducing deflections to less than 5/1000-inch, (2) minimizing the repair cost as much as possible, and (3) reducing the time required for implementation of the foundation remediation solution. After evaluating the advantages and disadvantages of several alternatives, jet grouting was selected as the most suitable solution. The jet grouting program provided columnar elements of soilcrete to remediate the Shoda Machine foundation.

Jan 1, 2003

By Robert E. McIvor

"“Classification System Efficiency (CSE)” is a powerful, emerging tool that can be used to increase grinding circuit efficiency. It is defined as the percentage of the ball mill energy being used to grind target, oversize particles. The discovery, validation and current use of CSE, including how it was manipulated, are described through seven plant case studies. These resulted in efficiency improvements ranging from 3 to 30 percent, along with major reductions in over-grinding. The achievable CSE for any given circuit is described. This paper demonstrates both how, and how much, every plant can benefit from increasing grinding circuit CSE.DEFINITIONS: BALL MILL CIRCUIT “CLASSIFICATION SYSTEM EFFICIENCY (CSE)”, “EFFECTIVE MILL GRINDING POWER”: “WASTED/OVER-GRINDING MILL POWER”The closed ball mill circuit is shown in Figure 1. The extreme importance of the circulating load ratio in determining circuit productivity was demonstrated by Davis (1925) and re-published by Guadin (1939), as shown in Figure 2. The circuit production rate increases with increased circulating load ratio, rapidly so at first and continuing to increase more gradually with higher and higher values of circulating load ratio.The underlying cause of this relationship was seen when comparing the ball mill feed and product size distributions from two different ball mill circuits, one with a low circulating load ratio, and one with a high circulating load ratio (Figure 3). While the F80’s and P80’s of these two circuits were close to the same, the mill feed and discharge size distributions were quite different. The ball mill in the circuit with the higher circulating load ratio contained a substantially greater fraction of material coarser than the target P80, as indicated by the respective mill feed and discharge size distributions. This fraction represents the fraction of the mill power being expended on “coarse” (in this case, plus P80 size) material, or the circuit “classification system efficiency.” The “effective mill grinding power” is the total mill power multiplied by the CSE. The compliment of CSE, the remaining fraction of “fines” in the mill, is the fraction of the mill power being wasted, and spent on over-grinding of material already finer than the circuit target product size. This is the “wasted/over-grinding mill power”"

Jan 1, 2013

By Sparrow G. J

The effect of polyelectrolyte flocculants on the de-watering of a tailing suspension of very fine clay was investigated.Sedimentation and filtration experiments were carried out in the labqratory to characterise the de-watering properties of the tailing. The results were used to calculate the effect of flocculant additions on the drainage and vaporation components of the de-watering of a clay suspension ponded on to a sand drainage bed.A flocculant increased the drainage rate, but decreased the volume of water that could be removed by drainage leaving more water to be lost by evaporation.The sorptivity values measured in the laboratory were used in the de-watering equation previously established for the tailing to estimate the effect of flocculant additions on the time required to de-water the suspension from 18.2 to 60 per cent solids w/w. The calculated de-watering times were found to increase or decrease depending on the volume of water removed by drainage and the prevailing evaporation rate.

Jan 1, 1980

By Wen-Chieh Cheng

Two bored piles with base grouting are loaded axially and the results are used to compare with numerical analyses. One compressive pile with a diameter of 2 meters is drilled through clay deposit and into bedrock to a depth of 13.7 meters. One tensile pile with a diameter of 1.5 meters is drilled through the same clay deposit and into bedrock to a depth of 17 meters. Both piles are installed with monitoring system such as rebar strain meters, concrete strain gauges and extensometers. The monitored data during pile load test are used to obtain average frictional stress (t) a displacement (z) curve, pile tip bearing (q) as well as pile head load (p) and a displacement (s) curve. FLAC3D is used to simulate the pile loading and base grouting. The soil and bedrock are modeled with Mohr-Coulomb. The parameters of the constitutive law are established from soil biaxial tests and rock bore hole deformation tests. The pile is assumed as an elastic body. The interface element is used to simulate the pile/soil interface and pile/rock interface. The numerical results are compared with the pile load test in terms of t-z curve, q-z curve and p-s curve. Finally, the pile base grouting is simulated and the uplift is analyzed. The result from this study is promising and the numerical modeling is successful.

Jan 1, 2006

By N. Anacleto, S. Ganguly

Reduction of Groote Eylandt (Australia) and Wessels (South Africa) manganese ores using CH4-H2-Ar gas mixture was investigated in a fixed bed laboratory reactor in the temperature range 1000?1200oC. The extent and kinetics of manganese ore reduction as a function of gas composition and temperature were determined by on-line off-gas analysis using mass-spectrometer and dew point sensor. Morphology of ores and its change in the course of reduction was examined by optical and scanning electron microscopy. Phases of raw materials and reduced samples were analysed by XRD and EPMA. Manganese oxides were reduced to carbide Mn7C3. High extent and rate of reduction by methane-containing gas in comparison with carbothermal reduction were attributed to high carbon activity in the reducing gas, which was in the range 15 - 50 (relative to graphite). The reduction rate of Wessels manganese ore increased with increasing temperature. Reduction rate and extent of Groote Eylandt manganese ore achieved maximum at 1050oC. The decrease in rate and extent of reduction of Groote Eylandt ore at higher temperatures, particularly at 1150-1200oC, was due to sintering and formation of semi-liquid silicate slag. The optimum conditions for the reduction of manganese ores were established as follows: a) temperature: 1150-1200oC for Wessels and 1050-1100oC for Groote Eylandt ores, b) methane concentration: 10-15 vol%, c) hydrogen concentration: above 30 vol%, (d) size: 1-3 mm. An addition of lime (10-15 wt% CaO) to the Groote Eylandt manganese ore increased melting temperature of slag and significantly increased the rate and extent of reduction at elevated temperatures.

Jan 1, 2004