Search Documents

By W. T. Abel

The rate of the steam-carbon reaction, which is of fundamental importance to coal gasification, was determined by passing steam over graphite specimens suspended in an electrically heated tube. The measurements were made at 1,900° to 2,400° F. and at steam-feed rates of 0.1 to 2.0 moles of steam per mole of carbon per minute. At the maximum steam-feed rate, the reaction rate of carbon ranged from 0.4 percent per minute at 1,900° F. to 7 percent per minute at 2,400° F. Up to about 2,200° F., the steam-feed rate had only a slight effect; above this temperature, it limited the reaction velocity when the final mole fraction of steam in the reaction products was much less than 1.

Jan 1, 1962

By W. W. Aljoe

The use of protective canopies can result in canopy roofing and/or serious restrictions to operator comfort and vision. To document this experience, BCR conducted a field study of cab and canopy design and application which resulted in a catalog of 164 canopy designs and an analysis of field data which showed no simple relationship between working height and canopy-related problems. The relationship also involves (1) machine frame height, (2) mine floor undulations, (3) operator compartment dimensions, (4) canopy design and location on the machine. Data analysis indicates (1) present technology does not always permit successful application of canopies in working heights below 42 inches, and (2) development of satisfactory low-coal canopies is doubtful. The basic conclusion of the study is that future R&D studies should be directed at development of alternative protection systems and remote mining methods.

Jan 1, 1981

By Alfred V. C. Meyer

A Blastcorder4 was calibrated on the Bureau of Mines shaking table in the frequency range of 12 to 40 c.p.s. and in the amplitude range' of 0.25 to 1.0 g. The results of this calibration study show that in the frequency range of 12 to 30 c.p.s. the average accuracy of the Blastcorder is approximately ± 0.1 g.

Jan 1, 1962

By Pierre Rocque

The Red Lake Mine is located approximately 600 km northwest of Thunder Bay. This 545 tpd (600 tons/day) underground narrow vein gold operation is set to produce in excess of 14.8 tonnes (475,000 ounces) in 2001 at a cash operating cost below 75 U$/oz. The high-grade nature of this deposit (>55 g/t or >1.6 opt) coupled with its complex geological environment and relatively deep location dictated the choice of a very selective primary mining method, Mechanized Overhand Cut and Fill. In addition to geological challenges, mine design issues such as material handling, ground stability and requirements for yieldable ground support are also discussed in this paper.

Oct 1, 2001

By C. H. Titus

This study consists of four descriptive Sections covering respectively: a state-of-the-art literature survey on ungrounded and grounded power systems, a report on literature pertaining to human threshold limits of electric shock, an analysis of the performance requirements of isolated systems and a section on design and performance specifications for an isolated system the final section includes copies, and translations where applicable, of the most important articles on foreign mining practice as well as some technical publications which could be difficult to obtain elsewhere. Section 2 - Literature Survey In analyzing the available literature on ungrounded systems it became apparent that too strict an interpretation of Section 1.1 of the Contract would limit the survey in both period of time analyzed and in available literature which discussed several types of power systems. Therefore, the survey was expanded to cover approximately the past twenty-year period and to cover literature which addressed itself to both ungrounded and grounded power system operation. Section 2 gives a brief summary of this literature survey and lists the important papers and books which were examined.

Jan 1, 1972

By Jay L. Hodkinson

Replacement of an aging twin span river crossing in Vermont required a temporary bridge to accommodate traffic during construction. Soils beneath the temporary approach embankment consisted of very soft organic clayey silt underlain by interbedded, loose alluvial fine sand and silt/clayey silt. Reinforcement was required for the southern temporary approach embankment to limit settlement and to increase global stability factors of safety. A ground improvement design was developed using Rammed Aggregate Pier® reinforcement and was included in the contract documents as an FHWA Category II Experimental Feature. Instrumentation intended to document the performance of the supported embankment was installed. Piers were then constructed and monitoring commenced as embankment and bridge construction occurred. Weekly instrumentation data reports indicated continuing excess pore water pressure, settlement, and lateral deformation of the subgrade soils as the embankment and temporary bridge abutment was constructed. In response to the unanticipated monitoring results, further investigation indicated that significant deviations from the conditions and basis upon which the ground support design was developed were made during construction. This paper discusses these deviations and their specific impacts to embankment support performance, how these deviations occurred, the role that the ground support system played in maintaining global stability, measures taken to limit further detrimental impacts to the embankment, and provides recommendations for contract document preparation and construction oversight to prevent similar situations from occurring on future projects.

Jan 1, 2011

By W Donovan

Concern exists about the potential release of metals from the proposed mining operation at Martha Hill to the Ohinemuri River. Speculation on possible impacts is fuelled by the dearth of published data on existing metal levels not only for this river system but for streams throughout the Coromandel. At first sight this lack of data is surprising given the apparent interest in this subject and the fact that future mining activity in this region has been a possibility since at least 1979. That such a situation has arisen is not altogether unexpected given the difficulties faced by various organisations, including the mining industry, in determining metal levels which are generally acknowledged to be low. This paper presents data for a number of stations in the vicinity of the proposed operation; it explains the analytical procedures which were adopted and the rationale for them and relates the information which has been obtained to water quality criteria.

Jan 1, 1986

By Val E. Payne

Issues between resource utilization and resource preservation often develop in connection with coal mining. One such conflict exists in eastern Utah where PacifiCorp and Energy West Mining Company are working with State and Federal agencies to address the resource recovery/resource preservation dispute. The effects of underground longwall coal mining on golden eagle (Aquila chrysaetos) cliff nesting sites have been studied at the Cottonwood Mine since 1986. Subsidence, escarpment spalling, and the nesting activities of the local eagle population were monitored.

Jan 1, 1986

By Costa

The fly-in-fly-out (FIFO) mining model has significant implications for the industry as it plays an important role in fulfilling the economic, social and workforce needs of the contemporary mining industry. It has increasingly been adopted in countries such as Canada and Australia, but is the current nature of the FIFO model challenging the place women have achieved in the mining workforce? Research in the mining and oil and gas industries reveals that major sources of stress for fly-in-fly-out mining workers are the times of parting and of reunion, the challenges in defining roles within the family, parenting, and conflict between spouses over the use of the leave time and money. So how are women in the industry coping with the FIFO schedules and consequent intermittent relationship with families and partners? How is the mining industry adapting to recruit and maintain female employees in FIFO operations? This paper describes an exploratory study conducted in Canada, which intended to provide some initial insights that might help us answer the questions above. There are several inferences made from this exploratory study. It is clear that FIFO poses significant challenges for both female and male workers. It is largely seen as rigid, extremely challenging for employees with young families and workers who are single mothers, and it is generally incompatible with starting a family and caring for small children. FIFO creates severe stress on relationships and on workers psychological well-being. It seems to be indeed harder for women, since they are often in lower paying positions and therefore have less financial reward for the FIFO lifestyle. On the other hand, FIFO creates the opportunity for young women, including Aboriginal women, to jump-start their careers, as well as opportunities for mature women to work while pursuing other personal interests during their time off. This paper concludes with recommendations to improve the FIFO system in order to increase the ability of mining companies to hire and retain women

May 1, 2006

By M Stewart

The structural framework for the major gold deposits of the Reefton Goldfield was largely established in the 1930s after a detailed regional geological mapping programme. Recent new mapping has now substantially modified the structural framework of the Globe Hill - Devils Creek area and the Waiuta area. Using bedding-cleavage vergence as a method of establishing fold limb facing, many new fold structures have been identified, some of which conflict with long-established structures such as the Globe Hill and Waiuta anticlines. In addition, the mapping of areas of west- versus east-facing limbs constrains the position of many faults. The mineralised Globe-Progress Shear is one such fault which graphically demonstrates major structural discordance of the folds in the hangingwall compared to the footwall. Recognition of the folding is establishing the structural framework for understanding of the origin of these productive gold mining areas.

Jan 1, 1996

By K. Lundholm, M. Andersson, L. Nevatalo, Å. Holmström, L. Hedström

"Several copper deposits have the arsenic bearing minerals enargite (Cu3AsS4) and tennantite (Cu12As4S12). Since this mineral contain both arsenic and copper, it is not possible to remove the arsenic by selective flotation. Partial roasting is a method to clean the concentrate from arsenic and thereby produce a suitable raw material for the copper smelter. Also mercury is commonly found in copper bearing minerals. In the partial roasting process both arsenic and mercury are volatilized, while part of the sulphur is used as energy during the roasting. This gives a calcine suitable as feed to a smelter, much like an ordinary copper concentrate. A typical analysis of calcine would be: S content 18–22%, As content below 0.3%, Cu content – not affected, grain size – not affected. However, if the concentrate contains mercury, the mercury will be volatilized during the roasting process. This will lead to very high mercury contents in the subsequent process of sulphuric acid, unless the SO2-rich process gas is pre-treated by the Boliden/Norzink process that recovers mercury as calomel, Hg2Cl2. The volatilized arsenic in the gas phase can be recovered either by dry or wet methods. However, one problem is that arsenic also contaminates the fine grained calcine dust that is captured downstream in the gas cleaning system. The calcine dust contains valuable metals such as copper, gold and silver that needs to be separated from the arsenic. The ultimate aim is to stabilize the recovered arsenic as a compound with minimum impact on the environment and recover the valuable metals. By using wet recovery methods it is possible to selectively precipitate copper, gold and silver as sulphides while arsenic is kept dissolved in the liquid. The precipitated metal sulphides can be mixed with the calcine and sent to the copper smelter. The dissolved arsenic is sent to effluent treatment and is further treated in Outotec ferric arsenate precipitation process, where arsenic is precipitated as the stable compound basic ferric arsenate, formula FeAsO4·xFe(OH)3. All concentrates containing arsenic are unique and the process design of a roaster plant must be based on relevant process data. The process data is collected during tests in lab scale and pilot scale, where the influence of critical process parameters on the quality of calcine is studied. The ability to run tests both in lab scale and pilot scale is crucial to the development of the correct roasting process. Outotec is well equipped for this."

Jan 1, 2014

By E. Wasmund

"Sandfire’s DeGrussa Copper-Gold operation in West Australia is a new high grade copper sulfide mine, which includes a 1.5 Mtpa concentrator which was completed in 2013.Early after commissioning, it was identified that the flotation capacity in the all-mechanical cleaner circuit was not sufficient. In order to improve recovery, the tail from the cleaner scavenger was sent back to feed the rougher scavengers. Test-work was done on-site to evaluate the possibility of using a flotation column as a pre-cleaner. A CavTube™ sparging system was selected, which is especially effective for fine ore particle flotation. Test-work was conducted at site using a 150 mm diameter unit, and then confirmed on a 500 mm diameter unit. A 4250 mm diameter full scale unit was installed in Q4 2014 and commissioned in Q1 2015. This unit gave some significant advantages including a reduction in re-grinding requirements, elimination of a circulating load and increase in the recovery of copper in the cleaner circuit and overall circuit.In this presentation, the benefits of columns and cavitation sparging for floating fine particles and rejecting fine entrained gangue will be explained. Also, the results from a lab unit and a pilot unit will be compared against the results of the full-scale unit. The paper will demonstrate the scalability of flotation columns, and which phenomena and scale-up criteria must be considered to be successful. Finally, some general observations will be made about the importance of columns in copper cleaning circuits.IntroductionSandfire Resources’ DeGrussa copper-gold concentrator is located approximately 900 km north-north-east of Perth in Western Australia. The project area landscape is scrubby mulga lands with few notable features. The climate is arid with high temperature and heavy summer downpours."

Jan 1, 2016

Determine the advantages and operational limitations of water-let-assisted cutting used with mining equipment. Approach The Bureau of Mines con-ducted a research study to evaluate water-Jet-assisted cutting both in the laboratory and in underground mines. Earlier research on water-jet-assist was limited to laboratory studies where bit speeds and penetration depths were very low and large cutting force reductions were reported. For the past years, research by the Bureau of Mines and others has been concerned with the application of water-jet-assisted cutting under more realistic mining conditions. Study Results Water-jet-assisted cutting employs a mechanical cut-ting bit combined with a moderate to high-pressure water jet directed just in front of the bit tip to assist in the cutting process. Recent Bureau findings show that the addition of the water jet to the cutting bit can improve cutting in harder materials, significantly reduce respirable dust and bit wear, and increase product size. Some of these findings are presented as follows.

Jan 1, 1987

By D. E. Wolfson

As part of its overall program of coal carbonization, the Bureau of Mines is studying the coking properties of coals that may be used for metallurgical purposes. The objectives of this study were given in detail in a previous report.2/ The suitability of coal for metallurgical use depends primarily on (1) chemical composition, (2) preparation characteristics, and (3) carbonization behavior. The first two factors, as well as the available reserves, are considered in selecting coals for carbonization tests. According to the estimate of reserves by Dowd,3/ the recoverable coal in Raleigh County in beds 28 inches or more thick, in thousand tons, is: [ ]

Jan 1, 1957

Flow Sheet Simulation of Municipal Waste Treatment Processes

Sep 13, 2010

By Roger E. Burleigh

In June, 1989, the U.S. Bureau of Mines, undertook a 9-day evaluation of the tin resource potential of the Sleitat Mountain tin deposit. Significant tin-tungsten mineralization is associated with quartz-topaz-white mica-tourmaline greisen alteration of a multi-unit, 57 Ma, peraluminous, granite stock which intrudes Cretaceous Kuskokwim Group flysch deposits. The granite comprises marginal biotite-, intermediate biotite-muscovite-, and central zinnwaldite-granite units, interpreted as a zoned alteration system. Major vein mineralization is confined to two east-west-trending zones of steeply oriented tabular lenses of greisen interleaved with mildly altered granite. Cassiterite is the dominant ore mineral while arsenopyrite, loellingite, wolframite, pyrite, sphalerite, chalcopyrite, and bismuth-oxides are present in minor to trace amounts. The north and south greisen zones are estimated to contain an inferred resource of 128 to 212 million lbs Sn in 28.6 million st of mineralized rock. An 1,800-lb representative bulk sample contained 0.37% Sn, 0.04% W and 17 ppm Ag and is considered an average grade estimate for the deposit. Drill testing by Cominco Alaska Exploration indicates that substantial widths of high-grade tin mineralization are included within the lower grade disseminated mineralization. Depth of deposit erosion is substantial and there exists a high probability for placer tin deposits.

Jan 1, 1991

By Dolly Chakraborty, S. Ranganathan, S. N. Sinha

Pre-reduction of chromite outside the submerged-arc furnace (SAF) can significantly lower the specific power consumption in the SAF process. Conventional processes for the pre-reduction of the ore operate at relatively high temperatures, at 1400-1500°C. It is possible to enhance the rate of reduction at low temperatures by optimizing the flow rate of inert gas over the reaction site. The influence of the flow rate of inert gas on the rate of reduction of chromite ore was investigated. The rate of reduction initially decreased wit the flow rate of the gas. It increased subsequently at higher flow rates to be followed by a decrease again. There was an optimum flow rate at which maximum reduction could be obtained. It was possible to achieve high levels of reduction at 1200°C by optimising the flow rate of the gas. The degree of reduction obtained was comparable to that obtained at 1400-1500°C, by conventional process routes.

Jan 1, 2007

By X. H. Zhang, J. G. Cai

This paper discusses the behaviour of large-span tunnels and caverns in hard rock in a major underground storage project. In-situ stresses were measured using hydraulic fracturing during site investigation and 3-D overcoring during construction, with both showing a horizontal stress ratio of 2-3 times the vertical stress. Rock reinforcement design was based on the Q-system combined with numerical modelling for special design cases. Tunnel design and performance were checked and monitored by in-situ instrumentation during rock excavation, including measurements of deformation, convergence, and load on rock bolts. Deformation measurements using borehole extensometers included one borehole drilled into the virgin rock before rock excavation, which provided a direct and very insightful comparison with the various deformation measurements made during rock excavation. These measurements coupled with numerical calculations have proven that the high horizontal stresses to be very favourable to the stability of the large openings.

Jan 1, 2003

By Ray Jambakhsh, Gabrielle Bourget

In the summer of 1998, Ontario Hydro awarded a contract to demolish an obsolete and inefficient chimney by blasting. The Ontario Hydro Thunder Bay Thermal Generating Station (T.G.S.), is a fully operational hydro thermal generating station located in Thunder Bay, Ontario, Canada. The Chimney was a 356 ft (108 m) high freestanding structure constructed of reinforced concrete with a brick liner. Falling the chimney required careful planning due to the highly sensitive structures and equipment which surrounded it. Damage either sustained to the existing systems through ground vibrations or direct contact would have resulted in expensive power outage and/or lost production. The role of Explotech Engineering Ltd. on this project was to provide and evaluation of the proposed demolition procedure, defme the predicted and maximum seismic vibrations at sensitive structures including underground services, conduct pre-blast / post-blast inspections and recommend various safety precautions. The general contractor for the project, LeBrun Northern Contracting Ltd., of Thunder Bay, Ontario was responsible for all site preparations and post-blast clean up. All demolition blasting calculations and operations were conducted by Dykon demolition experts from Tulsa, Oklahoma. On September 13, 1999, the chimney was successfully demolished. Extensive analysis of the vibration records and visual post-blast inspections of the surrounding structures concluded that the demolition event induced no damage to any of the Ontario Hydro facilities.

Jan 1, 2000

By M. H. Farjadi, J. Azari

Cost analysis of chrome ore reduction is one of the important issues facing ferrochrome producers in today?s competitive environment. Much of this depends on quality and various ratios in the actual ore. The latter can have a direct bearing on electricity consumption and optimum efficiency of the furnaces. While the industry has been successful in reducing costs by designing larger and more efficient furnaces, the role of the optimum blend of ore has perhaps been given less emphasis. This paper will discuss the general specification and metallurgical characteristics of various chrome ores for producing high carbon ferrochromium on industrial scale. By analysing the results obtained from smelting, including chromium recovery and energy consumption, the determining parameters in total cost of ferrochromium i.e. chrome ore; reductant and energy consumption can be optimized. Our study is based on actual experiences obtained from Faryab Ferroalloy Plant over a period of approximately three years.

Jan 1, 2004