Search Documents

By Ben Murphy, Tomi Maksimainen, Antti Rinne, Ishmael Muzinda, Toni Mattsson

"A 500m3 flotation cell was commissioned during 2014 at the Kevitsa Mine in northern Finland working as the first rougher in the copper flotation circuit. Treating around 850tph with an average grade of 0.3% Cu, the TankCell® e500 has run with an average copper recovery of 71% and an average enrichment ratio of 50 during early optimization test work. In addition the cell has proved to be very energy efficient, being operating with a specific energy of around 0.4kW/m3 under production conditions.A review of the installation and operation of the TankCell® e500 at Kevitsa will be presented. Metallurgical performance of the cell during the operating period will be discussed on the basis of on-line analysis and the metallurgical samples collected during early optimization campaigns.IntroductionThe past three decades have seen a rapid increase in the size of mechanical flotation cells. This has been largely driven by demand from the copper industry to process larger volumes of material due to combination of declining head grades and the desire to benefit from the economies of scale (Lynch, Harbort and Nelson 2010). During this period Outotec has been at the forefront of development of large flotation technology with an enviable scale-up track record; 100m3 (1995), 160m3 (1997), 200m3 (2002), 300m3 (2007), 500m3 (2012) to the largest commercially available cell at 630m3 in 2013. This scale-up methodology has been developed, tested and validated (Elgueta et al., 2009; Coleman & Dixon, 2010) by the large installation base of cells in the 300m3 size class operating (over 400). The learning from large cell operation are then reviewed and incorporated back into new designs and scale-up practices (Murphy, Miettinen, and Yanez, 2014)."

Jan 1, 2016

The Cowarra gold mine is at latitude 36°O'S. and longitude 149°19'E. which is roughly 20 miles north-north-east of Cooma.The deposit was· originally worked towards the end of the last century, but the presence of sulphides associated with the gold in the primary zone caused cessation of work when that zone was reached.GEOLOGY AND MINERALIZATIONThe principal country rocks are sandstones and shales of Silurian and Ordovician age, both very strongly folded with structural pitches ranging from a few degrees to almost vertical. The mine proper is within Silurian rocks and the main orebody (there are several minor parallel bodies) is developed within a shear striking approximately north, dipping approximately 70° east, and ranging in width from 2 ft to 15 ft but averaging about 4 ft.This shear is impregnated with quartz and sulphides with which the gold is associated. The predominant sulphide is pyrite though pyrrhotite is commonly present in quantity.Arsenopyrite and bornite are present in smaller amounts.Stillwell (1936, 1937a, 1937b, 1938, 1941) has published five mineragraphic reports on the ore.The various levels have been mapped in detail (Figs. 1-3) and the No. 2 level plan (Fig. 1) shows the general relationship of shearing, as now indicated by mineralization, and faulting. There is no apparent connection between the fold structures and mineralization.Fig. 3 is a longitudinal projection showing the distribution of gold expressed as inch-ounces. The estimation of...

Jan 1, 1965

The amount of liquid retained in a porous bed is determined by weighing a column containing the bed.The column is attached to the free end of a cantilevered beam, and changes in weight are determined by calibrated strain gauges (which form a resistance bridge) attached near the fixed cnd of the beam. By coupling the output from the strain gauges to an amplifier and a recorder, a continuous record of changes in the drainage characteristics of the bed may be obtained.

Jan 1, 1968

By John E. Newby

Washington?s King County is constructing a new regional wastewater treatment facility, called Brightwater, in response to growth in the greater Seattle region. Planning conducted in the late 1950s identified the need for two regional treatment facilities. Constructed in the 1960s, these plants have served the region well. However, an eventual need for a third facility was also recognized. The Brightwater project implements the final phases of the long-term plan. The project includes a new treatment plant and an extensive conveyance system. When completed in 2010, the Brightwater facilities will treat sanitary sewer flows from growing populations living in northern King County and southern Snohomish County. The new system will fulfill commitments to provide wastewater services to local jurisdictions and sewer service providers in the King County Service Area. It will also provide more flexibility in the operation of the King County regional wastewater system. The Brightwater wastewater treatment plant will provide secondary treatment capacity using membrane bioractor technology in 2010 for 36 million gallons per day (mgd), with anticipated expansion in 2040 to 54 mgd, using membrane bioreactor technology. These capacities are for average wet-weather flows. The plant will also accommodate peak hourly flows of 130 mgd by 2010 and 170 mgd by 2040. The Brightwater Conveyance System consists of more than 8.1 km (13 miles) of tunneled influent and effluent conveyance lines, five tunnel portals/shafts, microtunneled influent and outfall connec-

Jan 1, 2007

By X. Yu

Although many investigations of the deformation behaviour of rocks have been carried out, most of them are carried out in compression. In all rock engineering practice it is usually assumed that the deformation of rocks in tension is the same as that in compression. However, data from numerous researchers have shown that this assumption is not correct for some rocks. A new loading frame for testing rocks in compression and direct tension has recently been developed by the authors, with the capacity to conduct both compression and tensile tests on the same rock sample. The results obtained show that the ratios between the average Young?s modulus in compression (ECA) and in direct tension (ETA) are 1, 1.16, 2 and 6 respectively in four rock types tested. For Poisson?s ratios, analogous relations were obtained. It was observed that, in all cases, the tangent Young?s modulus intension reduces with an increase in the applied tensile stress, while the behaviour of Poisson?s ratio is similar, but shows greater variability. The difference between the Young?s modulus of rocks in tension and that in compression could lead, large errors in calculating induced stresses around underground openings, as well as in determining the Brazilian tensile strength of rocks. This may have a significant influence in rock engineering and therefore more investigation is necessary into the tensile deformation behaviour of rocks and its influence.

Jan 1, 2005

By A. Mahmoudkhani

Primary cementing is the process of placing cement in the annulus between the casing and the formations exposed to the wellbore. Portland cement was first used in 1903 in the Lopoc Field in California for well cementing. Since then, the major objective of primary cementing has always been to provide zonal isolation in oil, gas and water wells, i.e. to exclude fluid(s) in one zone from another zone in the well. To achieve this objective a hydraulic seal must be created between the casing and cement and between the cement and the formations, while at the same time preventing fluid channels in the cement sheath. This requirement makes primary cementing the most important operation performed on a well. Without complete isolation in the wellbore, the well may never reach its full producing potential. The industry knowledge on cements relies heavily on empirical data, but the chemistry, physics and structure of cement are not fully understood yet. The strength of concrete can be increased essentially by reducing its porosity through optimizing the size distribution of its components and filling the residual porosity of the hydrated cement phase with inorganic fillers. This approach has successfully utilized in different ways and several technologies for placing high performance oil and gas well cements have been developed over the last few decades. There are reasons to believe that the next source of improvement will lie in the fine-tuning of the hydrates themselves and of the different parameters that drive short (ionic?covalent bonding) and long (ionic correlation) interactions.

Jan 1, 2012

Alluvial gold was found in the Terawhiti area, West of Wellington, in the 1850s. This led to the discovery of reef gold. Periods of minor 'gold fever', company flotations, and mining activity occured between 1869 - 1973, 1881 - 1986, and in the late 1880s, with one final company active in 1911 - 1914. 1n the early 1980s, further field work was carried out. No viable mining operations resulted from any of this activity.

Jan 1, 1993

Operations and maintenance departments have had a long-standing adversarial relationship. The widespread evolution and adoption of modern management techniques, such as reliability centered maintenance (RCM) and Lean, however, has driven interest in working co-operatively to optimize overall plant performance. Mining and minerals operations have long adopted RCM in maintenance and are now adopting Lean throughout organizations. Such modern management initiatives explicitly call for co-operation between the two disciplines of maintenance and production and many advances have been made in terms of people and methodology. One area that has lagged behind in supporting these developments, however, is information systems. Enterprise asset management (EAM) systems in maintenance and newer manufacturing execution systems (MES) in operations have not been truly integrated in the needed ways. Complicated plants, different software architectures, continually changing conditions and many other variables have led to systems problems, which have contributed to the maintenance/operations divide. Master data synchronization (the plant tree) and integrated reporting of real-time data with transactional data are just two of the issues that are being solved by new approaches in information technology, including web services and service orientated architectures. New technologies are coming on-stream to enable the final bridging of the gap.

Jan 1, 2009

By R. T. Jones

The 20 Mt reverberatory furnace slag dump at Nkana in Zambia contains a substantial quantity of cobalt. A 40 MW DC arc furnace has been built at Chambishi for the purpose of recovering cobalt from the slag. The technology was jointly developed by Mintek and Anglovaal Mining Ltd (Avmin), and the furnace was designed by Bateman Titaco. Testwork at the 150?250 kW scale was conducted at AVRL, and larger scale piloting was conducted at Mintek (in partnership with Avmin) in a 3 MW DC arc furnace. Approximately 840 tons of Nkana dump slag (ranging from 0.66% Co) was processed at power levels around 1-2 MW. Good overall cobalt extraction was achieved, and approximately 100 tons of cobalt-bearing alloy was produced (containing 5 to 14% Co). This testwork demonstrated that the Nkana dump slag could be processed in a DC arc furnace of suitable design, to produce a cobalt-bearing alloy suitable for further hydrometallurgical processing. Bateman Titaco were contracted to design and build the furnace, and the design team contained representatives from Avmin and Mintek. The project was conceived as a fast-track exercise, and many activities had to be run in parallel. Notable features of the furnace include an ABB power supply, a Concast conductive hearth, the refractory design, and copper cooling in the sidewalls. Power to the furnace was switched on during January 2001.

Jan 1, 2002

By Tae-kyeong Yeu, Cheon-Hong Min, Hyung-woo Kim, Sup Hong, Minuk Lee, Chang-Ho Lee

This paper concerns the optimum arrangement of the buoyancy module, which is used for stable dynamic motion and structure stability of the marine flexible riser. The main method of this study is simulation-based design using Genetic Algorithm (G.A) for optimum design and Multi-body dynamic for simulation. The marine riser connects the vessel and the seabed-tracked vehicle. The motion of the riser affects the motion of the vessel and the vehicle. In this study, a marine riser of the deep-seabed integrated mining system (Figure 1) is used. This riser has a strong effect on efficient transfer of minerals. So, the buoyancy module must be equipped to supplement problems of the structure stability and the dynamic motion. Positions and quantities of the equipping buoyancy modules are determined by the at sea experiment (Figure 2). But this method is not easy because the actual sea experiment is expensive, time-consuming and dangerous (Figure 3). Thus, the position and quantity must be determined by simulation-based design. The dynamic analysis models of the riser and the buoyancy module were built in the commercial software DAFUL. In the marine environment, factors affecting behavior are current, drag force, etc.

Sep 1, 2014

By Ernie Holden, Chris Ringas

In the last 20 years, In Line Inspection (ILI) using intelligent pigs has become the principal tool used by pipeline operators to assess the condition of their pipelines. New pipelines are normally designed to take intelligent pigs, but many older pipelines require some modifications and special procedures for their inspection. This paper is aimed at practicing engineers and managers of pipelines, or people aspiring to those positions. The paper describes the benefits of ILI and some of the practical issues regarding pipeline preparation and cleaning, choice of inspection tool, running pigs in pipelines, and what to do with the data collected. What are the responsibilities of the Pipeline Engineer ? ? Maintain reliable and acceptable performance of the pipeline in terms of safety and product delivery at economical cost. ? Provide a defined margin of safety for operating the pipeline at its designated pressure. ? Provide timely information on all pipeline defects such that repairs can be carried out according to a managed schedule. What Defects does the Pipeline Operator have to cope with ? A useful record of actual incidents seen in pipelines can be obtained from the web site of the US Office of Pipeline Safety (OPS) - http://ops.dot.gov/stats/stats.htm. US pipeline Operators are obliged by Law to report all pipeline incidents exceeding certain threshold criteria (e.g loss of life, escape of product, cost of incident etc). These OPS statistics show that corrosion and third party damage have remained consistently the prime causes of reportable incidents in the US, with similar experience elsewhere. There are several kinds of flaws and defects in pipelines that can lead to failure, the main families being :- ? Metal loss ? Cracks or crack-like defects ? Laminations and other mid-wall defects ? Geometric anomalies

Jan 1, 2006

By S. Luyckx

This paper reports hardness and abrasive wear resistance test results from a wide range of WC-Co alloys, varying in cobalt content as well as WC grain size. The results show that the abrasive wear resistance increases with increasing hardness and that the rate of increase is higher for larger WC grain sizes. The increase in abrasive wear resistance was found to be parabolic up to a critical hardness value and exponential above that value. The transition from parabolic to exponential behaviour was found to occur at the same contiguity value for all grain sizes, which suggests that at that contiguity value the WC skeleton becomes continuous in all WC-Co alloys.

Jan 1, 2004

By A. Choudhury

Deep open-pit mines are becoming increasingly common in the highly mineralized arctic and sub-arctic regions. Air inversion is a frequent occurrence in these regions, and is exacerbated by the natural topography of an open-pit mine. Due to such inversions, the air quality in open-pit mines deteriorates very rapidly. Transport of gaseous pollutants under arctic air inversion is complex and involves an interaction between flow, thermal and convective transport systems. This paper discusses the construction and validation of a three-dimensional model that simulate the flow of air and the transport of gaseous contaminants in an arctic open-pit mine and the effect of low influent velocity and large gust velocities on the contaminants profiles in the mine. It was found that while higher velocities may remove contaminants from the pit bottom, they may not remove the contaminants from the pit entirely, necessitating artificial mitigation measures.

Jan 1, 2012

By G. P. Holmes

"IntroductionThe copper-molybdenum property of Brenda Mines Ltd. is located 18 miles north west of Peachland in the Okanagan Valley of the Southern Central interior of British Columbia. The actual site is 50 miles north of the international boundary and 150 air miles east of Vancouver at an elevation of 5000 feet above sea level. The earliest written mention of the prospect is found in the Geological Survey of Canada, Memoir No. 243, issued in 1947 by Dr. H.M.A. Rice. In 1954 the area was staked by a prospector, Bob Bechtel, who interested Bern Brynelsen of Noranda Exploration in examining the claims. A joint Noranda - Kennecott program resulted but since the grades were so low the property was not taken up until in 1964 a re-examination by Chapman, Wood and Griswold produced recommendations leading to the construction of the Brenda Mine as it is today.The rounded, timber covered mountains of the area are composed of the tuffs, argillites and limestones of the Upper Triassic Nicola Group, which is intruded by a Jurassic quartz diorite, called the Brenda stock0 The actual orebody occurs in a strongly fractured zone within the Brenda stock, approximately 1500 feet from the contact with the Nicola group0 The ore minerals, .chalcopyrite and molybdenite, associated with pyrite and magnetite of lesser importance, occur as fillings within the fractures 0 The grade of the ore decreases outwards from a central higher grade core and in January 1971 total reserves were estimated at 165 million tons assaying 0,182% Copper and 0,049% Mo."

Jan 1, 1972

By Tatsunori Matsumoto

In order to investigate the variation of the load-displacement relations of piles in a site, vertical load tests were carried out on 25 small diameter steel pipe piles. Out of 25 piles, 15 piles were close-ended pipe piles attached with a blade at the pile toe and 10 piles were open-ended pipe piles. To carry out these load tests in a short period, two types of rapid load test methods, Spring hammer load test and Falling mass load test, were employed. The load tests of all piles were completed in two days with 180 blows in total. In order to estimate a static load-displacement of a pile, non-linear damping method was used. It is shown from the test results that the performance of the pipe piles such as the ultimate pile resistance and the initial pile head stiffness is improved by re-driving.

Jan 1, 2006

By Todd Wanless

This paper addresses the challenges experienced by the designer and three government agencies during implementation of major improvements for the Turkey Creek Tunnel in Kansas City, Kansas. The tunnel serves as a vital stormwater conveyance system for upstream flood control. Major structural deficiencies were identified within the tunnel including complete loss of sidewall and invert. Without immediate attention, complete loss of the tunnel arch could lead to blockage and extensive remedial repairs under difficult conditions. Considering that tunnel flows must be maintained during construction, a phased design and construction process has been implemented to expedite stabilization of the erosion cavities followed by tunnel liner repairs.

Jan 1, 2008

By W. L. Garrison

Improvements continue to be made in rapid excavation and tunneling technology. There are several ways to examine the impacts of such improvements. The most common procedure is to monitor current developments and to evaluate prospects for expansion of present types of uses. Other approaches are called for, however, if the technology might be used in ways not now imagined, if the search is for information for managers of technology development, and if the issue is that of the wise use of the technology by society. The first section of the paper will pose these matters as questions. These questions will be examined from the point of view of the processes of technology development and utilization, and then further examined against the backdrop of processes at work within the urban area. Such an examination will provide insight into the way technology developments should proceed. The final section will present some comments that may be useful to those guiding the development of the technology and to those who might provide leadership for its wise utilization. THE QUESTIONS Three questions are posed: 1. Are there uses for the technology beyond further penetrations of its present markets? 2. Can information be supplied to managers of technology development so that they may improve the assignment of priorities among development choices? 3. How can society make wiser use of the technology?

Jan 1, 1974

By Zachary Mayer

Agenda ? Kidd Mine ? Background ? Problem & Opportunity ? Challenges associated to depth - Production Rates - Productive Work Time - Operational Delays - Transfer Levels - Mucking Time - Impact on Hoist ? LHD Automation ? Sandvik AutoMine Lite ? Expected Benefits Kidd Mine - Background ? Located in Northern Ontario, Canada ? Underground base metal mine operating since 1966 ? Total 148 Mt mined (2.31% Cu, 6.08% Zn, 75 gpt Ag) ? 2.35 Mt/Y from stopes as deep as 9500 ft (2.9km) below surface ? Mining method: blasthole open stoping ? Mine/Mill: 1263 employees and contractors ? 2012 National John T. Ryan Safety Award

Aug 1, 2013

By G. Naud, J. Robitaille, M. Buonvino, A. Veltmeyer, A. R. Laplante

"A B6 Falcon concentrator was tested on several systems: a synthetic magnetite-silica ore, a massive sulphide gold-copper ore, a fine gold-pyrite-silica flotation tail, and a high grade gold ore in a low sulphide gangue (cyclone overflow).The Falcon demonstrated its ability to achieve separation in all cases, but with varying degrees of success. For the magnetite-silica system, separation proceeds until the concentrate bed overloads, at a mass of 300 to 400 g of magnetite. Recovery increased with decreasing particle size, down to the 25-37 µm and in some cases even the -25 µm class. Bowl geometry (angle) and gangue size distribution were the most significant operating variables. Results with the massive sulphide ore were the poorest, with gold recoveries typically around 10 to 20% at very low upgrading ratios, 1: 1 to 5: I. Gold recovery from the fine flotation tail ranged from 30 to 70% at upgrading ratios of 5 to 15; actual plant application would require a continuous unit (Falcon C20). The high grade gold cyclone overflow yielded a wide range of gold recoveries, but a very consistent relationship between recovery and mass processed. A concentrate of 0.5% Au could be processed at a recovery of 50%.The paper also presents results of a C20 application to recover fine iron from a magnetic tail. The unit is capable of recovering approximately 70% of the fine liberated iron in a high density product, with modest upgrading below 105 µm, and virtually complete rejection of the + 300 µ m product."

Jan 1, 1993

By Xing Jin, Dan Graffi, Glenn MacPherson, Dan Rioux

"The complexity of a modern flotation circuit makes it susceptible to disturbances such as changes in feed, ore mineralogy, equipment degradation, poor measurements and faulty instruments. Good measurements and a robust control system are critical to create and maintain a stable and optimum flotation process.This paper focuses on the development and implementation of process control applications in the flotation circuits at Xstrata Nickel’s Strathcona Mill ( referred to as the mill hereafter ) in Sudbury, Ontario. Following the path of ‘stabilize-improve-optimize’, basic controls to stabilize process variables such as flotation cell pulp level, air and reagent addition rates, cleaning-column feed and wash-water rates have been established. Factors such as best practice in pulp level and valve position measurement, feedforward control and the application of an appropriate control philosophy, have contributed to the significant reduction in process variability. For instance, standard deviation reduction of 79% for the Ni impurity in the column Cu concentrate grade was experienced and is shown. The variability reduction of the flotation circuits’ key process-variables paves the way to further improve and optimize flotation performance. A grams-per-metal unit reagent addition control scheme has been improved upon, particularly for different operating scenarios and better robustness. In addition, following significant stabilization of the primary controls and columns feedrates, Cu/Ni separation cleaning-column bias-control (cascaded to the wash-water rate) and hold-up control (cascaded to air flowrate) have been developed and tested. This strategy – from stabilization to optimization - is expected to achieve a more consistent control of final concentrate grades and improve recoveries.INTRODUCTIONFlotation is considered the most important and value-added process in the milling metallurgical plant and is still undergoing continuous evolution to treat greater tonnage and different ores (Wills, 2006). Starting over three decades ago, with the advent of on-line slurry content analysis devices, flotation automatic control has received persistent interest and a large number of applications have been reported (Thwaites, 1983, 1986 ; Mckee, 1991). Bergh and Yianatos (2011) reviewed different aspects of process control in flotation circuits and have evaluated the applicability of model predictive control to the process. Mckee (1991) analyzed the difficulty in developing lasting/robust process control applications for flotation circuits and stated that the path of stabilization-refinement-optimization would more likely lead to successful flotation circuit process control. Best practice on column process control was discussed by Bouchard, etc. where a multi-layered approach was proposed, provided that the measurement of column process variables ( i.e. bias, froth depth, hold-up, etc. ) are measured reliably (Bouchard & Thwaites, 2008). Wills (2006) stated that the best practice for flotation automatic control starts with fulfilling basic control objectives, such as stabilized flotation cell level, air flow, pH, reagent flow etc., before considering more advanced, or even optimal, control of metallurgical targets, which are more closely linked to economic performance."

Jan 1, 2013