Search Documents

By S. Hardcastle

Various controlled and ambient tests were undertaken to evaluate the performance of a variety of digital heat stress monitors, psychrometers and simpler temperature/relative humidity data loggers that measure, or determine, such parameters as: dry-bulb, natural wet-bulb, psychrometric wet-bulb and globe temperatures. In this comparison, funded by the Deep Mining Research Consortium, it has been found that all the instruments can competently measure dry-bulb temperature but the accuracy of other sensors could introduce significant uncertainty. For example the quality of relative humidity sensors and failure to correct for the barometric pressure difference in deep mines, directly impacts upon the calculation of psychrometric wet-bulb. The comparison has shown that the response of dry-bulb and globe temperature sensors can vary widely under different radiant heat conditions; however this would be negligible in most mines. Of more concern is the differing performance of the natural-wet bulb sensors especially at low relative humidity and low air velocity. Furthermore, from these tests and the currently available theory it was not possible to determine if any of the natural-wet bulb instruments measured that value correctly or validate any relationship between psychrometric and natural wet-bulb temperature at low air speeds where their difference is greatest. Consequently the uninformed use of some of the commercially available environmental heat stress monitors or derivations from other instruments could provide erroneous results affecting the work load category that can be accommodated or the rest ratio regime required.

Jan 1, 2009

By Vincent Joannes, Marine Lasne, Luca Brenelli, Colin Serridge, Inge van Baardwijk, Martin Stanley, Anthony Fisher, Mary Ellen Bruce, Tony Suckling, Pedro Avellanosa

"Abstract The European Federation of Foundation Contractors (EFFC) and Deep Foundations Institute (DFI) developed a sector-specific carbon accounting methodology and associated “carbon calculator” for foundations and geotechnical works. The EFFC-DFI Carbon Calculator is believed to be one of the construction industry’s first collaboratively produced carbon calculator tools for European and international countries based on verifiable and standardized data. It is intended that the tool be adopted internationally and become the open-source industry standard for ground works. A detailed methodological guide is provided with the calculator (Lemaignan and Wilmotte, 2013). This guide explains the background of the standards, accounting methodologies, emission sources and factors that were used as the bases for the tool development and includes detailed guidance on use of the calculator.Drivers for DevelopmentFoundation contractors anticipate project cost and carbon emissions will become inextricably linked in response to the climbing price of fossil fuels and carbon intensive materials as resources become scarce. Low carbon solutions will therefore become more competitive options. Also with high profile construction projects having low carbon/carbon neutrality as requirements, sustainability in the foundations industry also becomes a market issue.This carbon calculator will be used to lead the industry and shape the expectations of commissioning organisations by providing insight into the carbon cost of their projects. Commissioning organizations are encouraged to be aware of the carbon impact of projects and to also facilitate a fair and accurate way of comparing footprints to provide a level playing field for foundation contractors."

Jan 1, 2014

1. A statistical approach to some mine valuation and allied problems on the Witwatersrand. Unpublished Master?s Thesis, University of the Witwatersrand ? 1951. (Separate) 2. A statistical approach to some basic mine valuation problems on the Witwatersrand - J. of the Chem. Metall. and Min. Soc. of S.A., December, 1951 - discussions and replies March, May, July and August 1952. (Vol. 1?.1). Also: J. of the Institute of Mine Surveyors of S.A. December 1952, March 1953. (Vol. 1?2) 3. A statistical analysis of some of the borehole values of the Orange Free State goldfield - J. of the Chem. Metall. and Min. Soc. of S.A., September, 1952 - discussions and reply November 1952, and February 1953. (Vol. 1?3). 4. A study of the relationship between development values and recovery grades on the South African goldfields - J.S.A.I.M.M, January 1959, - discussion and reply April and October 1959. (Vol. 1?6) 5. On the departure of ore value distributions from the lognormal model in South African gold mines. J.S.A.I.M.M., November 1960, January and August 1961. (Vol. 1?8) 6. Developments in the valuation of gold mining properties from borehole results - Seventh Commonwealth Mining and Metallurgical Congress, 1961. (Vol. 1?9) 7. Effective pay limits for selective mining. J.S.A.I.M.M., January and August 1962. (Vol. 1?10)

Jan 1, 2014

By Manqiu Xu

"Ore grades are decreasing and ore deposits are becoming more complex. In order to make a sound economical decision about a mining project, metallurgical testwork must be carried out. A few large “representative” samples cannot represent the metallurgy of a large ore body and a large number of samples reflecting variation in ore head grades and in mineralization types must be obtained for proper metallurgical studies, including flowsheet development for a greenfield project. A relationship can be established between the recovery of valuable minerals and ore grade for each mineralization type. This relationship can be used to establish a correlation between values recoverable and values contained in the ore body that can include multiple pay metals. With this information, a sound economical decision can be made about the viability of a large mining development project.INTRODUCTIONThe demand for minerals today is historically high as many countries are being rapidly industrialized. The supply for these minerals is not necessarily running short. However, it is widely accepted that the world today is running short of the easy to mine and easy to process ore deposits. As ore grade is decreasing and ore mineralogy is becoming more complex, metallurgical testing must be fully conducted in order to make a sound economical decision about a mining project. For a high-grade and high-quality deposit, it is hard not to make a good profit even with low metal prices. For a low-grade and hard to process deposit, the profit margin is much lower and is dependent on the throughput and the recovery of valuable minerals. The recovery of valuable minerals is a function of ore grade and mineralogy and it must be experimentally determined for a given processing option.At Vale Base Metals Technology Development, metallurgical testing for an existing operation or brownfield project is termed as Ore Evaluation, while metallurgical testing for a greenfield project is termed as Flowsheet Development (Xu, 2011). In the past, metallurgical testing involved a few large composite samples for lab and pilot plant testwork. As ore deposit becomes less homogeneous and more variable, a few large composite samples cannot represent the metallurgy of a large ore body. In addition, useful information about the deposit such as zones of “impurities” or floatable rock minerals would not be obtained. Different processing strategies could have been developed if the locations and sizes of these zones were known in advance. For proper metallurgical studies, a large number of samples reflecting variation in ore head grades and in ore mineralization types must be used. A relationship can be established between the recovery of valuable minerals and ore grade for each mineralization type. This relationship can be used to estimate values recoverable in the ore body that can include multiple pay metals. Ultimately, the recovery verses ore grade relationship will be used in business decision-making."

Jan 1, 2013

By Changsheng Song

With increasing depth of coal mining in China, the number of coal and gas outbursts has been increasing for years. By means of destressing the protective seam, the gas in the protected seam is drained to reduce gas concentration in the high gassy seams, thus ultimately attaining simultaneous extraction of coal and gas. Base on the simulated material scale modeling and numerical simulation, the protective seam mining method was practiced at No. 8 coal mine in Pingdingshan city. After extracting the No. 15 seam, the overlying strata movement and the deformation of No. 9-10 protected seam were studied. The experiments showed that it was feasible to destress the protected seams with large interburden thickness. As the protective seam was being mined, the protected seam experienced dynamic movement process and the change in vertical stress in the No. 9-10 seam assumed ?W? shape. When the face had advanced 656 ft (200m) from the setup room, the No. 9-10 seam was fully destressed, resulting in easy gas drainage in the destressed zone. Recommendations on mining sequence of multiple seams mining in the Pingdingshan coal areas were made.

Jan 1, 2008

By F. Block, K. Kohli

Outcrop barrier pillars serve to keep mine personnel and the public safe from sudden uncontrolled flows of water accumulated in active and abandoned underground mine workings. When an outcrop barrier fails, the result is an outbreak of water to the surface and is termed as blowout. Mine blowouts are associated with above-drainage mines and can occur through the coal outcrop and sealed portals. A blowout is often catastrophic, a threat to the people on the surface living or working in the path of a potentially large flood. In addition, blowouts can destroy homes, cause landslides and severe erosion and release pollution and acid mine drainage. This paper provides guidance on the planning, design, evaluation and inspection of barriers to address the problem of mine blowouts associated with above-drainage coal mines.

Jan 1, 2007

By Andrea M. Ouchi

A major focus of ground control research presently being conducted by the Geomechanics Group in the University of British Columbia Mining Engineering Department is to incorporate weak rock masses (RMR76 less than 50) into existing empirical design relationships. An emphasis is being placed upon the updated span design curve/critical span graph originally developed at UBC. The original database has been augmented by mapping of one mine in Montana and of several mines within the Carlin and Getchell Trends of Nevada. In addition, a neural network analysis has been performed and modifications of the span design curves at the lower RMR76 range have been made. The common factor in all the above mentioned mines is a weak back and/or walls. In most cases, the ore zone is the weakest rock unit and must be dealt with to safely extract the mineral bearing rock. This work attempts to provide rock mechanic tools that will enable a mine operator to make economic decisions that will also ensure a safe working environment.

May 1, 2004

By Gregory M. Molinda

The Coal Mine Roof Rating (CMRR) was developed 10 years ago to fill the gap between geologic characterization and engineering design. It combines many years of geologic studies in underground coal mines with world-wide experience with rock mass classification systems. Like other classification systems, the CMRR begins with the premise that the structural competence of mine roof rock is determined mainly by the discontinuities that weaken the rock fabric. However, the CMRR is specifically designed for bedded coal measure rock. Since its introduction, the CMRR has been incorporated into many aspects of mine planning, including longwall pillar design, roof support selection, feasibility studies, extended-cut evaluation, and others. It has also become truly inter-national, with involvement in mine designs and funded research projects in South Africa, Canada, and Australia. This paper discusses the sources used in developing the CMRR, describes the CMRR data collection and calculation procedures, and briefly presents a number of practical mining applications in which the CMRR has played a prominent role.

Jan 5, 2007

The 102nd Annual General Meeting of The South African Institute of Mining and Metallurgy was held in the Gold Room, Transvaal Automobile Club, 60 5th Street, Lower Houghton, Johannesburg on Wednesday, 18th August, 1999. Obituaries The President announced the death, during the year, of the following members: Honorary Life Fellows and Past Presidents D.D. Howat Life Fellows O. Deane, J.S. van Zijl Fellow A.A. Hejja Retired Fellows A.L. Forder, C.B. Parker, A.C. Petersen, F.W.J. Ross Members J.S. Stanko, D.H. Gray Retired Member P.K. Bredell Retired Associate I.S. van Eyssen In memory of the deceased and in sympathy with the bereaved, all rose and observed a moment of silence.

Jan 1, 1999

This is an abstract from Environmental Service and Technology (Vol 32 No 20 1998) which will be o finterest to South African Mining and Metallurgical Scientists, involved in chromium mining and Metallurgical processing. Maybe the scourge of our dams and reservoirs?the water hyacinth can be put to good use! The novel technology of phytoremediation embraces plant accumulation processes for the cleanup of toxic heavy metals and organic chemicals. Several plant species have been identified that are excellent hyperaccumulators of a number of heavy metals, e.g., Brassica juncea (Indian mustard) and Thlaspe caerulescens (Alpine pennycress). Other speciesincluding Myriophyllum brasiliense(Parrot?s feather), Salixsp. (willow), and Popullussp. (poplar) have also demonstrated phytoremediating abilities.

Jan 1, 1999

Modelling and Simulation to Design a Flotation Circuit for Gold Concentration

Sep 13, 2010

By Bassam Kattaa

"Abstract - A heavy mineral survey of beach and dune sands including geochemical analysis for trace elements was undertaken to evaluate the economic potential of the sands and to understand the nature and distribution of the heavy minerals relative to potential source rocks. Results indicate that heavy minerals are generally derived from outcropping volcanic rocks that comprise a proportion of the hinterland in the south part of our survey area. The most abundant minerals are magnetite and pyroxene. The morphologies of the heavy mineral grains are angular to subangular, suggesting that they were transported short distances from the source rocks. Factors controlling heavy mineral distributions include wave and wind action, proximity to provenance, the fluvial drainage network, and longshore currrents.The most economically important mineral is ilmenite. Zircon and rutile concentrations are relatively minor and thus have lower economic potential."

Jan 1, 2002

Newcrest Mining is one of the leading independent gold producers in Australia thanks in large part to its Cadia Valley operations. It is the largest gold and copper producer in New South Wales and one of the largest in Australia. This year Newcrest will expand its operations with a A$545-million expansion in the area. The Cadia Valley is approximately 250 km (155 miles) west of Sydney. The province presently includes the Cadia Hill opencut mine and the Ridgeway underground mine. With a significant mineralized system to the east of Cadia Hill and a mineral resource below Ridgeway, Cadia Valley has the potential to underpin Newcrest?s production for up to 30 years. In 2007, total gold production for the company in-creased to more than 50 t (1.6 million oz) and cash flow increased by 47 percent, according to the company?s annual report. The history of mining in the area dates back to 1851, but Newcrest?s history is young. In 1990, Newcrest commenced activities in the Cadia Valley. In 1992, Cadia Hill was discovered, with the discovery of Cadia East (1995) and Ridgeway (1996) following close behind. In 1998, the Cadia Hill openpit mine was commissioned. In 2002, the Ridgeway underground mine was commissioned and in 2007 the company?s board of directors approved an A$545 million development of the Ridgeway Deeps. The Ridgeway underground mine is located adjacent to Cadia Hill. The Ridgeway orebody has no surface expression but lies approximately 500 m (1,640 ft) below the surface and resembles an inverted teardrop. It measures approximately 450 m (1,476 ft) by 250 m (820 ft) and extends in excess of 850 m (2,788 ft) in depth. Ridgeway is a sublevel caving operation. Crushed ore from underground is delivered by conveyor to a surface stockpile, adjacent to the Ridgeway concentrator. Using similar processes to the adjacent Cadia Hill concentrator, gold and copper are recovered in a conventional flotation circuit to produce a copper concentrate containing elevated gold levels. Ridgeway concentrate is combined with the Cadia Hill concentrate before it is pumped to the filtration plant in

Jan 1, 2008

By A. A. Smithen

There is an increasing awareness of the importance of including an assessment of environmental liabilities in the preparation of bankable feasibility documents. This means that environmental assessments of proposed, existing and decommissioned mine sites have to be undertaken for the purposes of quantifying environmental liabilities and assessing potential risks. This paper examines the need for considering environmental liabilities before describing the approach adopted in undertaking due diligence studies for the preparation of bankable feasibility documents and some of the difficulties experienced. Finally, some concluding remarks are made and the implications for the mining industry are discussed.

Jan 1, 1999

By Michelle Mouton, Johanna van Deventer, Jussi Vaarno

Mintek has been involved in numerous projects to remove Fe and Mn from dilute Co sulphate solutions by means of oxidative precipitation using air/SO2. Test work was done using a gas induction system, designed and supplied by Outotec. Various aspects, such as SO2 concentration, SO2 flowrate, impeller rotation speed and pH were investigated on a 2 m3 scale. Batch tests were performed using a residence time of 5 hours. Mintek has been involved in numerous projects to remove Fe and Mn from dilute Co sulphate solutions by means of oxidative precipitation using air/SO2. Test work was done using a gas induction system, designed and supplied by Outotec. Various aspects, such as SO2 concentration, SO2 flowrate, impeller rotation speed and pH were investigated on a 2 m3 scale. Batch tests were performed using a residence time of 5 hours. Impeller rotation speeds of 0-220 rpm were tested, and it seemed that speeds of between 80 and 220 rpm gave similar Fe and Mn removal rates. Co and Cu losses were generally below 1% and 5% respectively at pH 3.

Jan 1, 2007

By H. P. Willard, R. W. Gates

Basic Inc., has been mining magnesite and brucite for 27 years at Gabbs, Nev. This is a medium sized open-pit mine. The magnesite deposits are in north-western Nye County about 30 miles east of Luning, Nev., on the west slope of the Paradise Range, at an elevation between 5000 and 6000 ft. The magnesite and associated brucite is used to make magnesia refractories employed principally in the steel industry and magnesium oxide for various chemical uses.

Jan 10, 1963

By Juan Lucero

Como consecuencia de los factores externos e internos, las empresas mineras necesitan ser más eficaces a través de la implementación de nuevas tecnologías e informática. En este sentido, la compañía minera Milpo disminuye los costos de hardware para así generar un control de operaciones más minucioso, automatizado y oportuno. Los principales logros obtenidos son el control detallado de las operaciones, los sistemas operativos son la base para obtener los costos operativos, una mejor formulación y control presupuestal, control de servicios de terceros y el de los sistemas integrados.

Sep 13, 2001

By H. G. Denkhaus

Please allow me the temerity to reply to your reply to my contribution as follows: A fracture is brittle if plastic deformation is absent or, conversely a fracture is ductile if plastic deformation is present. Consequently, brittleness is specified by the degree of plastic deformation at fracture. This is the generally accepted definition. If other material properties (e.g. the quorient or the product of the uniaxial compressive and tensile strengths) under certain conditions are influenced by brittleness, or brittleness by them, these should not be called brittleness. If the one or the other author does that, he simply uses imprecise language. Even your remark, that ?Inyang and Pitt (1990) stated that the ratio of the compressive strength (sc/st) is directly proportional to brittleness?, confirms that the two quantities are not considered the same. For example:? The well known definition that a material is linear?elastic if the strain is directly proportional to the stress?does not mean that stress (measured in MPa) and strain (measured in %) are the same thing.

Jan 1, 2003

The authors summarise the development and recent advances in the reconstruction and visualisation of three-dimensional objects from point data and describe applications to the reconstruction of orebody shapes from drill-hole and other data. In particular, Dijkstra's algorithm is proposed and implemented as a means of optimal reconstruction of complex orebody and topographical shapes from irregularly located sample data. The surfaces of the shapes are constructed from triangular tiles and the algorithms proposed by the authors are guaranteed to find the optimal set of tiles that "best" construct the surfaces on the basis of specified objective criteria. The algorithms are illustrated by applications to a complex silver/gold/zinc/lead deposit.

Jan 1, 2002

By Patrick F. R. Murphy

The mechanization of platinum group metal (PGM) underground reef mining in South Africa has posed a challenge to mining engineers for several decades. This is primarily due to the shallow dip angles and narrow thickness (<1.1m) of the tabular orebodies mined, and the issues faced in developing reliable drilling, bolting and loading machines suitable for such hard-rock mining applications. Presently, mining is typically conducted using hand drills and scraper shovels. These methods, however, are intensive in terms of manual labor, and limited in terms of productivity, and improved methods are desired. This paper will review the technical features of a 4 tonne, low-profile, LHD for narrow-reef PGM mining, developed by EJC Loaders Division.

May 1, 2003