Search Documents

By A. K. Singh

Between the main fan and the coalface in a mine a lot of air is lost through leakage at stoppings, doors, air-crossing etc. so that a much larger quantity of air has to be circulated by the fan in order that the stipulated quantity of air reaches the face. Stoppings are of vital importance not only for effective ventilation of underground mines but also for isolation of areas affected by fire or susceptible to spontaneous heating. Generally, isolation stoppings are made of brick in cement mortar. If the area is far from the pit or unapproachable, it is very difficult and sometimes impossible to build these stoppings. To overcome these difficulties, particularly near fire affected zones, an alternate successful attempt was made in Indian mines to make a plug underground, from surface through borehole, using cement concrete. In this paper the salient features of the methodology adopted for construction of the plug and the experimental procedure for the measurement of air leakage by SF6 tracer gas is described. Measurements of air leakage through rows of ventilation stoppings in two mines viz. Moira (Jambad and Kajora seams) and Kuardi11/12 (Niga seam) collieries of Eastern Coalfields Ltd. (ECL) have been incorporated. Results of experiments conducted at the Central Mining Research Institute (C.M.R.I) to determine leakage through25 and 38 cm thick brick stoppings are also discussed. Results of all these studies are compared, which show that the efficacy and reliability of the remote filled cement concrete plug in respect of air permeability is satisfactory.

Jan 1, 2004

By L A. Maslov

We have considered the following characteristics of the crust and upper mantle of the Pacific Belt: seismic wave velocity anomalies, mechanical stress and shear deformation rate fields, heat flow and the pattern of metallogenic provinces of the Belt. It has been noted that there exist certain .regularities in distribution of the above mentioned geophysical characteristics and metallogenic zones within the Belt, displayed by prevalence of the lithophile elements in the Asia-Australian part of the Belt, and of the chalcophile ones within the American part.

Jan 1, 1995

By Charles Barnhart

This paper is a discussion of the causes of deflagration in cast blasting and a description of a project intended to demonstrate how changes in six critical parameters contribute to the deflagration chemical reaction. Control of these parameters is key to solving the nitrogen dioxide “orange smoke” problem. Preliminary results of an investigation into the development of a technology addressing the problem of atmospheric releases of nitrogen dioxide during cast blasting in surface mine operations are described. The project is funded by a $600,000 Small Business Innovative Research grant from the National Science Foundation and an $80,000 Abandoned Coal Mine Land Reclamation Program grant from the state of Wyoming. The presentation will address the measures required to control the blast chemical reaction so that it does not produce nitrogen dioxide through deflagration. Experimental blast data will be focused on a new shaped charge detonation system designed to instantaneously bring the powder column to maximum velocity of detonation (VOD), thus insuring efficient detonation of the entire colulnn.

Jan 1, 2003

By Don Rose

INTRODUCTION A number of tunnels supported and permanently lined by steel-fiber-reinforced shotcrete (SFRS) have been built in North America in the 1980s. The material is more economical than, and technically equal or superior to, conventional shotcrete using wire mesh. The design and construction of SFRS-lined tunnels is straightforward, and only a few new design principles, laboratory tests or construction equipment modifications appear necessary in order to use this material. Modern tunnel Contractors may use cyclic drill-and-blast methods on some tunnels, with intermittent shotcreting as part of an orderly cycle. The Dry Mix method is most suitable for cyclic, intermittent, relatively small-scale shotcreting. However, modern Contractors excavating tunnels continuously using large long Tunnel Boring Machines (TBMs) or Roadheaders may prefer Wet Mix shotcreting on a mass production basis. In either case, the use of steel-fiber-rein¬forced shotcrete (SFRS) promotes the rapid and economical excavation of tunnels. The addition of microsilica will improve SFRS properties and reduce rebound, and is expected to become standard practice with SFRS in North America, as it now is in Scandinavia. HISTORICAL REVIEW Steel-fiber-reinforced shotcrete (SFRS) at the present time (1985) is essentially conventional shotcrete with straight or deformed steel fibers added, and in general SFRS for tunnel linings encounters the same problems that conventional shotcrete does. Shotcrete history is well known. The use of sprayed plaster on wire frames for mounting animal skins by Carl Akeley of the Smithsonian

Jan 1, 1985

By M. M. Botz

There are currently more that 460 mines worldwide that utilize cyanide for gold and silver extraction. Despite this large number of cyanide-related mining operations, there have been no published accounts during the previous 25 years of the death of humans due to cyanide as a direct consequence of major mining-related environmental incidents. All published accounts of human deaths due to mining-related environmental incidents have been the result of physical inundation with tailings or waste rock materials. It appears that major mining-related environmental incidents have not been concentrated in any geographic location, are likely to occur regardless of the size of the mining company and do not occur more frequently with a specific type of mining activity. Several cyanide treatment and recovery technologies have been widely demonstrated to reliably control cyanide levels in mining solutions. With proper use of these technologies, tailings cyanide concentrations can be maintained at levels protective of wildlife while reducing the potential for adverse environmental incidents. The development of an international cyanide code of practice or management plan is recommended and should take into consideration the adoption of a weak-acid-dissociable (WAD) cyanide standard that maintains the levels entering a tailings impoundment below 50 mg/L.

Jan 1, 2001

By Hernán Parra

El presente trabajo señala la fase de tratamiento metalúrgico de pirrotitas que contienen oro, donde en la concentración por flotación se encontró un esquema adecuado para tratar pirrotitas auríferas considerando las restricciones ambientales que no permitieron incorporar técnicas de cianuración directa, que es como suelen tratarse es-tos minerales en el mundo. Asimismo, se propuso el uso de concentradores centrífugos para recuperar el oro libre fino en una primera etapa gravimé-trica, y concentradores de mesa Gemeni para obtener concentrados de alta cali-dad disponibles para fundición.

Sep 9, 2007

By G. R. Moulder

A device was developed that measures dynamic stress (ultrasonic energy) transfer through installed rock bolts, a measure that is directly proportional to the degree of grout bonding of the bolt to the mine roof structure and thus the ability of the bolt to bear static stress. The rock bolt bond tester (RBBT) is a hand-held portable device that shows three ranges of bolt bond condition; i.e., one-third (Bad bond), two-thirds (marginal), or fully bonded. These are shown respectively by a red, yellow, or green light that displays for 4 s. RBBT performance was verified with 2 1/2-to 8-ft bolts installed in various types 0f mine roof structures (sands tone, shale, and boney coal-mud), and 15 now being tested by the Bureau of Mines in mines across the United States. The unit is about the size of a five-battery flashlight and contains the transducer electronics, and battery pack. The RBBT is designed for extreme ease of operation, requiring only manual contact with the bolt and signal read-out. The batteries are rechargeable and the package is designed for durability in a mine environment.

Jan 1, 1983

In this paper, uniaxial compression tests were conducted on intact rocks and broken rocks that were reinforced by grouting, and the effects of grouting on the strength of broken rocks were analyzed. The results show that after grouting reinforcement, the bearing capacity of broken rocks with different lithologies increased, and their uniaxial compressive strength recovered by approximately 6%–16%. The results indicated that the stronger the rock, the smaller the strength recovery of the consolidated body formed after grouting. At the same time, using borehole camera observation and deep overburden strata separations, the fracture development characteristics of surrounding rocks of the gob-side retained entry were analyzed and divided into different regions. On this basis, a guided grouting method was proposed; that is, shallow hole grouting was first used in the plastic zone of the broken surrounding rocks to form the isolation layer, and then deep grouting holes were arranged in the elastic-plastic zone of the transition zone to guide the slurry flow to the shallow unfilled zone. Therefore, the broken surrounding rocks were reinforced into an integrated body and selfbearing capacity improved.

Jul 28, 2020

By Sir Robert Hadfield

SINCE the writer has been intimately connected with the development of manganese steel for many years, some remarks upon the early work with regard to the rolling and forging of this material might he of interest, and particularly as to the question of rails of special quality and of superior wearing qualities. In a paper on Iron Alloys, with Special Deference to Manganese Steel, read before this Institute at the International Engineering Congress in Chicago in 1893,1 the writer mentioned that, about 20 years ago, his firm in Sheffield produced railroad material, such as tires and axles, of forged and rolled manganese steel, thus showing that this product could be manipulated and worked up into the various required forms. The tires illustrated in the paper referred to above formed a particularly difficult class of work to produce in a special steel, but no special obstacles were met with Although there was no difficulty at that time in making and producing manganese steel in various forms, forged, rolled or pressed; nevertheless, on account of its higher expense, sufficient encouragement

Jan 2, 1914

By Thomas E. Doerfler

Information and data related to the occurrence of fatalities due to major disasters in metal/nonmetal underground mines were analyzed. Standard statistical methods were used to estimate the probability of occurrence of major disasters, and to examine the relationship of disasters to injury statistics published annually.

Jan 1, 1980

By Robert A. Pond

Heavy (exceeding 35 tons) roadheaders have not seen much use in the United States, but are used extensively in Europe to excavate many types of underground openings in civil and mining applications. Early models of roadheaders were light and suitable only for utility excavation such as drift enlargement or chamber excavation, unless the ground was very soft and easily cuttable. Frontier-Kemper Constructors, Inc. is now using a 45-ton roadheader to excavate two mine slopes in Kentucky and a 70-ton roadheader to excavate a long decline at a new mine in Utah. Results to date indicate that heavy roadhead machines are an effective alternative to both conventional excavation and full-face boring machines in many cases; and where circumstances are favorable are a superior choice. This paper concentrates on applications in the mine development construction industry, but the conclusions are no less valid for civil construction.

Jan 1, 1983

By Garry M. Johnston, Matthew L. Sutcliffe, Nicholas J. Welham

"The predominant current processes for the treatment of oxidized copper–cobalt ores use a reductive acid leach to bring the desired metals into solution. However, the indiscriminate nature of acid leaching results in a solution, akin to a metal soup, containing not only the Cu and Co but also an extensive suite of other metals. These other metals, notably Fe, Mn, Al, Ca, Mg and Si, all have to be eliminated from solution before the copper and cobalt can be recovered. Generally precipitation processes are used, but these tend to result in significant losses of copper and/or more usually cobalt from solution, leading to reduced recoveries. The AmmLeach® process uses ammonia-based chemistry to selectively leach the target metals, leaving the rest behind in the leach residue. This approach eliminates any need to clean the solution of unwanted metals and the consequent metal losses. After solid–liquid separation, the leach solution is immediately subjected to separation and concentration of the copper and cobalt using solvent extraction and electrowinning. INTRODUCTION The Copper Belt extends through the northern part of Zambia and the southern province of Katanga in the Democratic Republic of Congo (DRC) and contains the richest and highest grade deposits of copper and cobalt remaining in the world. Whilst there are a number of mines that produce sulphide concentrates, using froth flotation, the largest deposits are those where near-surface sulphides have been weathered over time to form oxides. The oxides cannot be concentrated by conventional physical means to give high recoveries. Despite this, a number of dense medium separation plants have been installed and used to produce a higher grade concentrate which is typically exported (while the rejects, typically 2 to 3% Cu are stockpiled for treatment at a later date). These plants generally have low recoveries and can only be used on the dwindling supply of high grade materials. In exporting the concentrate, little value adding is undertaken within the country, thus greatly reducing the economic benefits to the country. Recent changes to the regulations in the DRC will effectively ban the export of low value ores, concentrates and intermediates in favour of high value metals. This will necessitate mines to install new processing circuits in order to comply with these regulations. The head grade of ores currently being treated in the DRC is slowly decreasing as the extremely high grade materials are being selectively mined out. In many cases, the removal of a small volume of high grade materials leaves a much larger volume of economically marginal ore behind. This is due to a desire for short-term profits overtaking long-term prosperity. The remaining ore, which in many cases is still of relatively high value by world class standards, is likely to be only treatable by low cost heap leaching. There are some initial trials of heap leaching within the DRC, but implementation at a large scale has yet to be adopted."

Jan 1, 2015

By A. Beitz, P. Smartt, G. Einicke, G. Rowan, P. Glynn

Coal is Australia’s highest export earner and Australia is the world’s largest exporter of coal. With coal now being extracted from deeper reserves under increased risk profile, and in the interest of aiding the stability of coal supplies, Japan is funding a number of safety projects in Australia and China. The CSIRO, Australia’s premiere research organisation with the country’s largest exploration and mining research group, are currently undertaking a jointly funded Japan-Australia safety project at Anglo Coal’s new Grasstree Colliery in central Queensland. The project, entitled Mine Communication and Information for Real-time Risk Analysis, will deliver step-change capabilities in data integration, decision support, gas monitoring, geo-technical monitoring, emergency response and personnel safety to the Grasstree Colliery. Some key activities include: developing and installing underground coal mine Ethernet LAN components, real-time monitoring of gas and geo-technical sensors, MODBUS serial to TCP/IP converters, e-reporting of underground conditions, emergency guidance systems and underground trials of Internet Protocol telephone and video. The project seeks to integrate (in real time) key data sets from the comprehensive and diversified range of propriety system currently in use at mines (ventilation, strata, operations e.g. haulage, pumps, conveyors etc) into a single integrated risk management interface. This interface will filter the data through a rules-based inference engine that will cross reference the various data streams, compare with past events and outcomes associated with the similar historical data and present this “intelligence” to

Jan 1, 2003

By L. Connolly, F. R. De Luca

"Rubber liners at Denison Mines Limited are used in 10 1/2x 24' low discharg0 pebble mills. These were originally 10 1/2 x 13 Dominion overflow type ball mills. Experience here shows that the wear of rubber and ni-hard lifters is approximately the same in the feed end half of the mill, while the wear of rubber lifters is much greater in the discharge half. The wear of rubber plates is considerably less than white iron in the feed end half of the Mill and slightly more in the discharge end half of the Mill. Rubber components are lighter to handle but their installation is time consuming. This leads to the conclusion that a combination of ni-hard lifters a~~ rubber plates is the most economical compromise in Denison's case, for the Mill. Rubber discharge grates are superior to steel grates, while steel feed end liners are superior to rubber.The Use of Rubber Mill Liners at Denison Mines LimitedGrinding is done in two identic0al circuits each consist-ing of one 10 1/2 x 14' Dominion overflow rod mill, two Dorr Oliver quadraplex rake type classifiers, two 10 1/2 x 24' Dominion low discharge grate pebble mills and ancillary pumps and conveyors for pebbles. There is one centrally located distributor box that receives the discharge of the 4 pebble mills and splits it out to the classifiers."

Jan 1, 1974

By Jiwei Duan

The energy transferred from a hammer to the pile top is considered as the effective energy in this paper. The effective energy is related to the pile dimensions, soil and pile-soil interface properties. This relation may be expressed as an equation based on the dimensionless theory. The relationship between pile capacity and effective energy was studied by performing a series of wave equation analyses using a commercial software called GRLWEAP (Wave Equation Analysis Program) by GRL Engineers, Inc. The results show that the pile capacity increases with the blow count when the effective energy is constant, however, it has a little change as the blow count is over 100 blows per foot. The pile capacity decreases as the ratio of pile penetration depth to pile diameter increases if the effective energy is constant. The pile capacity will increase as the pile diameter and wall thickness increases if the effective energy is constant. The pile stickout (pile length above the ground surface) does not have a significant effect on the effective energy and may be neglected. Curves for pile capacity versus effective energy are presented to be used for preliminary hammer selection according to effective energy and hammer efficiency. Finally, a case from PDA testing was studied. Measurements of the effective energy and pile capacity by CAPWAP were presented and compared with the results by GRLWEAP.

Jan 1, 2006

By Edwin Berry

THE consideration of the present value of a mine is of great importance when planning for the operation of a property,, and it is particularly so in the case of mines that have large ore reserves. At various times during the past 15 years, the writer has had occasion to make rather thorough studies of the subject, and has been greatly impressed by certain important points which these studies have brought out, points which, though they may be well known, are often lost track of in the rush to obtain low mining costs and high daily tonnage output. . It is the object of this paper to present briefly, and in a general way, some of these points, and especially those which have to do with the relationship which (1) ore reserves and plant capacity, (2) grade of ore mined, and (3) ore losses in mining, bear to the present value. Present value, sometimes called present worth or actuarial value, means the value today of the future earnings of an enterprise. Great industrial, manu-facturing or railroad enterprises, if properly handled, go on indefinitely and their value is directly dependent on their estimated annual earnings. Mines, or oil properties, on the other hand, have an earning capacity only until the ore or oil is exhausted, and their present value is dependent not only on their annual earnings but also on their life, which is the length of the period over which they can produce at a profit. A mine, or an oil property, is a "wasting asset," while an estab-lished manufacturing business is not, or should not be. In other words, the present value of a mining property. represents a sum of money on which there could be paid from operating profits a determined rate of interest, say 8 per cent., and in addition an amount which, if invested at compound interest as received, would at the end of the life of the mine pay back the present value. In his "Wealth and Income of the American People," Walter Renton Ingalls says: "The fundamental principle of mine valuation is the present worth of an annual dividend accruing during the period of years corresponding to the life of the mine."

Jan 7, 1922

By Hans Korfmacher

Product take-back regulations implemented in Europe have presented significant challenges to the consumer electronic product and battery industries. Initially companies established single compliance organizations within individual Member States. These programs met business needs but were inefficient and costly. They were protected from pressures of marketplace competition and could not leverage economies of scale. In order to address these problems P&G, Hewlett Packard, Sony and Electrolux conceived a pan-European compliance organization to collect waste electronic equipment Europe-wide. This organization, called the European Recycling Platform (ERP), operates in competition with existing national compliance systems. Since 2005 ERP has collected 800,000+ tons of waste electronic products and delivered millions of dollars in cost savings. This presentation reviews the steps needed to establish successful competitive collection organizations that provide sustainable recycling at the lowest cost.

Jan 1, 2010

By Jozef F. Zurawski

Increasingly new interceptors or new Combined Sewer Overflow (CSO) projects require connections to existing tunnels. More often than not, the existing facilities are old, in poor or questionable conditions, without proper construction records or as-built drawings. Many cannot be easily inspected unless major construction effort provides flow by-pass for safe access. This paper provides general guidelines on how to approach the problem of assessing the condition of old tunnels, how to plan and design the connection with limited physical assessment, how to develop the scope of work for the bid documents and how to provide geotechnical guidelines and designs for the bid documents.

Jan 1, 2008

By David Shatwell

Recent epithermal gold discoveries in Chile and Bolivia provide increasing evidence of a belt of intermittent, epithermal, precious metal mineralization east of the main Andean porphyry copper belt. This relationship may be the result of an easterly decrease in the age of magmatism and erosional levels, in¬crease in depth above the underlying Benioff zone and consequent changes in magma chemistry, or some other unrecognized factor. Examples are: • The Choquelimpie gold-silver mine in Chile and numerous other epithermal prospects (such as La Riviera, Bolivia) in late Tertiary volcanics along the Chile-Bolivia border. These lie east of the belt that contains the Toquepala, Quellaveco and Cuajone porphyries in southern Peru and the Cerro Colorado, Copaquire and Quebrada Blanca porphyries in northern rhila

Jan 1, 1990

By Shi Hongchao, Zou Zou Xinkuan, Zhang Jichun

As drilling and blasting is carried out in an urban tunnel, which is adjacent to an existing building or structure, the balance between blasting-induced vibration reduction and drivage efficiency is a most important issue that must be resolved properly. Therefore, a new cut blast method named Stepped V-cut millisecond blasting (SV-cut) was developed by optimizing the most common used Vertical V-cut blasting method (V-cut). The most significant features of SV-cut lie in the utilization of sublevel interval charging structure and millisecond delay blasting technology in cut hole and the cut-cavity formed from outside to inside sequentially. SV-cut provides advantages of high borehole using ratio, low vibration level, and satisfied advance per attack. Based on the principal of millisecond blasting, the rock fragmentation process and the vibration reduction mechanism of SV-cut are analyzed. Determining methods of blasting parameters, which do have significant effect on vibration intensity and cut-cavity formed quality, are proposed according to the forming requirement of both outer and inner cut-cavity and vibration reduction. In order to compare the performance between SV-cut and V-cut, field blasting experiments were performed in the blasting engineering of Yamalike twin-arc tunnel, which closely passes over aged parallel tunnels. Blasting results show that SV-cut blasting is proven as an effective tunnel blasting method for both increasing blasting effects and decreasing blasting vibration. Comparing SV-cut with V-cut, the SV-cut can increase blasting drivage about 8.5% and reduce the vibration intensity induced by cut hole blasting 30% at least.

Jan 1, 2015