Search Documents

By S. E. Olsen, K. Tang

The complex heterogeneous equilibria associated with the production of manganese ferroalloys have been simulated by employing recently developed thermochemical databases. The non-ideal Mn-Fe-Si-C alloy and the MnO-SiO2-Al2O3-CaO-MgO-FeO slag system have been modelled separately by the compound energy and cellular model. A large number of experimental thermodynamic and phase-equilibrium data were used to evaluate the model parameters for the liquid and solid Mn-Fe-Si-C phases. In addition to the liquid metal phase, solid mixture phases occurring in the Mn-Fe-Si-C system have also been studied. Over 500 measured equilibrium data have been utilised to verify and calibrate the model calculations. The paper will present typical simulation results, from activities of components to multicomponent heterogeneous equilibria. Good agreements can be obtained for many important technological parameters such as carbon solubility, phase relations and equilibrium diagrams, element distribution as function of temperature and slag composition etc. Application of the present models to the silicomanganese production will be demonstrated in this paper.

Jan 1, 2004

By G. Norman Owen, Roger E. Scholl

INTRODUCTION The analysis and design of underground structures to resist vibratory motion due to earthquakes has been of interest to engineers for several decades. The dynamic stability of a powerhouse cavern was considered in the 1960s (Campbell and Dodd, 1967). About the same time, the designers of the San Francisco Bay Area Rapid Transit system developed procedures for analyzing the subaqueous tunnels placed under San Francisco Bay and the tunnels excavated along the land portions of the alignment (Kuesel, 1969). Japanese designers developed fairly sophisticated procedures for analyzing subaqueous tunnels during the late 1960s and early 1970s (Kuribayashi et al., 1974). In the past decade, proposals to site important critical underground facilities in regions with moderate to high seismic activity have increased the interest in earthquake engineering of underground structures. Seismic designs or seismic studies have been conducted for rock caverns for storage of petroleum or location of power plants (Yamahara et al., 1977; Glass, 1976), buried tanks for fuels or rad¬ioactive waste (Fukushima et al., 1977; URS/Blume, 1976), tunnels for disposal of nuclear waste (Yanev and Owen, 1978; Wahi et al., 1980), and urban mass transit tunnels (Monsees and Merrit, 1984). One of the greatest drivers of the interest in seismic analysis and design of underground structures has been the proposals to dispose of high-level nuclear waste in mined repositories some 300 to 600 m (approximately 1,000 to 2,000 ft) below the ground surface. In 1979, the authors, in conjunction with Professor Tor Brekke, presented a paper on an evaluation and design procedure used in a study of a proposed nuclear waste repository (Owen, Scholl, and Brekke, 1979).

Jan 1, 1985

By W. D. Guo

With an experimental apparatus developed recently, model tests on piles were conducted in sand subjected to triangular soil movement profiles. Four instrumented piles tests are reported, which show the pile behavior predominantly determined by soil sliding depth. Axial load can create additional bending moment and pile deflection, which also make mode of pile-soil interaction change with sliding depth. Limiting resistance was found 1.5~3 times higher than currently used for laterally loaded piles in sand.

Jan 1, 2006

By I. G. Gonçalves

For most industrial minerals, the color is directly associated with economic value. In terms of physics, the principal property that defines the term ?color? is the intensity of light reflected (or transmitted) by an object over the visible band, comprehended between 400 and 700 nm. This reflectance spectrum serves as the starting point for a variety of color-describing factors, the most common in the mineral industry being the brightness (TAPPI, 1977 and 1986) and the L*a*b* system (HunterLab, 2008). Quality specifications for mineral products are usually based on these colorimetric parameters. This market is becoming increasingly more selective and demanding over the quality of raw materials and alongside the traditionally controlled characteristics, such as particle size distribution and chemical composition, a trend exists towards the establishment of increasingly more strict specifications for the optical properties of these materials. This is due to the fact that most plants consuming these industrial minerals incorporate them into products in which the visual appearance is controlled. For these plants, most of them being the manufacturers of plastics, paper, paints, and ceramics, variations in the color of mineral materials result in difficulties to achieve the right color in the final product. Therefore, these plants set strict specifications for colorimetric parameters such as whiteness and yellowness, as well as colorimetric coordinates like L*, a*, and b*. For the manufacturer of industrial minerals, this translates into difficulties simply because many of these parameters are usually alien to the tradition of the mining industry. The main quality parameter in the kaolin industry is brightness, which is a weighted average of reflectance values over the range of 400-510 nm (TAPPI, 1977). Due to the lack of a better property, producers tend to use brightness to also assess the quality of the in situ ore and along the processing operations. However, the unprocessed kaolin is often accompanied by ?contaminant? minerals. For Brazilian kaolins, which are the object of this study, the most important contaminants are hematite (Fe2O3), goethite (FeOOH), and anatase (TiO2). Each of these contaminant minerals has a distinct color and behaves differently during the processing of the kaolin ore. Hematite and goethite in particular are particularly strong pigmenting agents and at concentrations as low as 100 ppm they can make the difference between a high-quality white pigment product for paper coating and waste material. As each Fe-bearing contaminant has a different color and responds differently to processing operations (for example, magnetic separation, chemical bleaching, selective flocculation, and/or flotation in the case of kaolin), the in situ brightness tends to show a poor correlation with the brightness of the final product. Brightness measurements are sometimes complemented with X-Ray Fluorescence (XRF) analysis of Fe and Ti, but the total oxide content provided by XRF is also poorly correlated with product quality because Fe may be in the form of goethite, hematite, or inside the crystalline structure of kaolinite. Thus, a more robust technique capable of distinguishing each mineral phase is desirable. Diffuse reflectance spectroscopy has been used to analyze iron oxide/hydroxide content both qualitatively (Torrent and Barrón, 2003; Liu et al., 2011) and quantitatively (Jiet al., 2002 and 2006). These authors correlate slopes and inflection points at characteristic absorption bands with oxide/hydroxide content in natural soils. The approach presented here involves the extensive use of the Kubelka-Munk (K-M) theory, which has been used for color matching (Schabbachet al., 2009 and 2011) and particle size determination (Otsuka, 2004) in a simplified version. Unfortunately, the scattering constant S is very difficult to measure for dry powders, because the equations require a thin layer of material. Attempts have been made (Gonçalves and Petter, 2007, and Gonçalves, 2009) but the experimental errors tend to be high. Thus, this paper aims to develop a tool for the quantification of contaminant minerals in kaolin based on the K-M theory without resorting to measurements over thin layers. This tool is based on a new two-constant approach, which takes into account differences in scattering between materials over the whole measured spectrum. The experimental dataset consists of the reflectance spectra of mixtures between a bleached kaolin and synthetic Fe pigments.

Feb 27, 2013

By Y. Guglielmi, V. Merrien-Soukatchoff, I. Kadiri

ABSTRACT: Hydraulic experiments have been conducted since 1997 within a small fractured calcareous rock mass in southeastern France, at a site called Coaraze. On this reduced-scale site closing a floodgate located on a downstream spring produces repeated hydraulic loadings. Simultaneous measurements of normal deformations and pressure in several joints have provided a better understanding of the hydromechanical behaviour of such a fractured rock mass. The present paper first describes both the site and conceptual interpretation of the measurements performed. We showed that accurate measurement reproduction requires incorporating certain features: a variable normal joint stiffness, the joint vicinity (through introducing a Z coefficient), and the initial stress state. The paper then develops an original analytical interpretation of the coupled pressure-displacement measurements carried out, which reveal the high level of measurement suitability to the non-linear behaviours examined. 2D modelling, using the discontinuous code (UDEC) was used to proceed with the calibration step. KEY WORDS: In situ test, methodology, hydromechanics, modelling, non linear behaviour ZUSAMMENFASSUNG : Hydromechanische Experimente werden seit 1997 in einer kleinen Kalksteinmasse, das sich im Südosten von Frankreich befindet durchgeführt. In diesem kleinen Standort, werden wiederholte Wasserdruck Erhöhungen durch das Schliessen eines Hahnes produziert. Gleichzeitiger Druck und normale Verformung Meßungen in mehreren Fugen haben erlaubt, das hydromechanische Verhalten einer solche gebrochene Felsenmasse besser zu verstehen. Der Artikel beschreibt zuerst den Standort und stellt die begrifflichen Interpretationen der Meßungen vor. Um die Meßungen gut zu reproduzieren ist es wesentlich, bestimmte Faktoren wie die veränderliche normale Steifheit der Fugen, die Nachbarschaft der Fugen (über einen Z-Koeffizient) und der Spannungstand zu berücksichtigen. Der Artikel erklärt die originale Methode für die Druck- und Verformungs-Meßungen Interpretation und zeigt die gute Korrelation der Meßungen mit dem nicht-linearen angenommen Verhaltens der Fugen. Die numerische 2D-Modellierung mit dem UDEC Software ist für die Verkeilung der Faktoren gebraucht worden. SCHLÜSSELWÖRTER: In-situ-test, Methodologie, Hydromechanik, Numerische Modellierung, nicht-lineares Verhalten RESUME : Des expérimentations hydromécaniques sont conduites depuis 1997 dans un petit massif calcaire fracturé situé dans le sud de la France. Dans ce site de taille réduite des mises en charge répétées sont produites par la fermeture d'une vanne située à l'aval du site. Des mesures simultanées de déformation normale et de pression dans plusieurs joints ont permis de mieux appréhender le comportement d'un tel massif fracturé. L'article décrit dans un premier temps le site et présente les interprétations conceptuelles des mesures. Pour bien reproduire les mesures, Il est essentiel de prendre en compte certains facteurs tels que la raideur normale variable du joint, le voisinage du joint (par l'intermédiaire d'un coefficient Z), l'état de contrainte initial. L'article précise la méthode originale d'interprétation des mesures pression-déplacements qui montre la bonne adéquation aux lois de comportement non linéaire proposées. La modélisation 2D, à l'aide d'un code discontinu (UDEC) a été employée pour le calage des facteurs. MOTS-CLEFS : In-situ, méthodologie, hydromécanique, modélisation, comportement non linéaire

Jan 1, 2003

By L. Nichols, H. Keele, K. Czajewski

"The oil sands industry in northern Alberta disposes of the by-products of bitumen extraction into tailings ponds. The mix of tailings sand and mature fines, with gypsum added as a flocculent, constitute a waste stream called consolidated tailings or composite tails (CT). The two main challenges of the tailings disposal process are a chronic shortage of economical containment and the potential mobility of CT deposits in the event of breaching by, for example, long-term erosion, which makes abandonment of tailings ponds more complicated. Thick deposits of CT do not consolidate in adequate time to provide reassurance for abandonment of the CT containment facilities and that is why the containment must be adequately robust or the properties of CT improved for long-term stability. This paper addresses potential solutions to these problems by applying the gravity drainage of CT and quasi-homogeneous construction for containment facilities.Gravity drainage is suggested as a mechanism to facilitate the consolidation of CT in critical areas of the ponds by inserting internal sand layers within the body of the deposit. Critical CT areas are defined as areas around the perimeter of containment. The advantages of this solution are longterm stability of the disposal area by creation of stiff deposits around its perimeter and facilitation of reclamation efforts on its surface.The present solution for containment of CT deposits is not favourable from a materials balance point of view. In general, sand has become a valuable resource as it both forms the primary component of the CT matrix and becomes the containment building material. If sand is required for CT, less is available for dyke construction. This puts additional pressure on the industry as a whole to maximize the use of overburden and interburden for construction of tailings containment structures. Typically, only 50 percent of dry mine waste (overburden + interburden) is incorporated into dyke construction. The remainder of dry waste is stored either in waste dumps or in tailings ponds, consuming valuable in-pond space originally allocated to CT material. Quasi-homogeneous dykes are proposed to contain CT deposits rather than traditional minimum cross-section dykes built of overburden and/or cell sand. The quasi-homogeneous dyke may change the unfavourable material balance and lessen the construction constraints that are presently imposed on the mine/waste disposal process."

Jan 1, 2008

By Tom Ireland, Tony Rock

The proposed 1.83km long twin bore A3 Hindhead road tunnel planned for contruction in 2008 is being delivered under a Highways Agency Early Contractor Involvement (ECI) contract. The proposed construction methodology is progressive mechanical excavation of a horseshoe shaped tunnel with shotcrete installed close behind the face using robotic spraying equipment. The tunneling medium is a ‘soft rock’ sandstone for which there was little previous tunneling experience, requiring extensive geotechnical investigations and an innovative approach to lining design. A 240m long portal section though sandy material utilising a steel pipe umbrella is also required. This paper describes the development of the tunnel planning and design including the most recent developments in UK road tunnels, and the innovation included in the ‘permanent’ primary lining design.

Jan 1, 2007

By J. A. Cruise

With the end of the official apartheid legislation in the early 1990s, South Africa was heralded as a non-racial country. However, racial awareness has been reintroduced into the country with the Affirmative Action and Black Economic Empowerment legislation. Gender and racial transformation are the current order of the day. All organizations are required to reflect in their make-up the demographics of the population as soon as possible. Scorecard shave been drawn up to measure the rate of transformation for gender and race in organizations. The mining industry in South Africa has been in the forefront of this transformation legislation and scorecards. This paper seeks to show the effect of gender and racial transformation on mining engineering education and professionalism by analysing the changing demographics of graduating mining students at both the South African universities offering a degree in mining engineering, the professional registration of mining engineers with the Engineering Council of South Africa (ECSA), and the membership of the Southern African Institute of Mining and Metallurgy (SAIMM), the vocational institute for mining engineers. It also demonstrates the absurdity of gender and racial quotas based solely on the demographics of the current population of the country. This paper shows the degree to which mining engineering has transformed in both gender and race.

Jan 1, 2011

By Cary Hirner, David Stacey, William A. Rochford

Design considerations and construction techniques were implemented to address groundwater infiltration from a confined aquifer during the excavation and lining of the Cady Marsh Flood Relief Tunnel. This 3-m finished diameter, 2-km long tunnel was successfully completed cost-effectively in an urban setting near East Chicago, Indiana. The soft ground was mined using a conventional tunnel boring machine with hydraulically actuated flood doors and supported with steel ribs and timber lagging. The tunnel was lined with cast-in-place concrete. Dewatering was implemented in settlement prone, boulder-laden ground in residential neighborhoods during construction to depressurize and partially dewater the aquifer at the tunnel horizon. This paper describes the design decisions and construction methods utilized to mitigate and limit infiltration into the tunnel during construction and operation, as well as manage ground settlement.

Jan 1, 2007

One of the most significant problems experienced in land reclamation work has been the tendency of earthmovers to over-compact the subsoils and topsoils. The need for extensive subsoil drainage, because of over-compaction, becomes a very expensive exercise and can be attributed to poor planning. The problem has been addressed both at the Waihi and Huntly open-cast mines through the use of low ground pressure machines in the placement of subsoils and contouring. The use of subsoilers working to contour to aerate the soils is essential to integrate both the sub and topsoils so that significant root growth and drainage is established. Waihi's rainfall (approximately 200 mm annually) and light soils create difficulties in preparing for the final seed bed. A noticeable factor in preparation of the growing medium was the reaction of the lime particularly in the subsoils (damp), from a lumpy, quite heavy texture to almost a seed-bed texture within a period of approximately 72 hours. Also the high incidence of stone and debris which was not apparent in the placement of subsoils meant the job became very labour intensive. This will be overcome with the importation of a machine from the USA. All of the rubber tyred tractors used on these projects are four wheel drive in the 6S-aOhp range which for weight distribution and the safety factors allows for good landscaping techniques. Good engineering practices should ensure that slopes of no more than 3:1 be designed, keeping in mind that the long term planning must allow for maintenance and stock management of restored land.  In the preparation of the final growing medium the equipment used included: Caterpillar 05 LPG and blade; three-four wheel drive rubber tyre tractors; Super flow subsoiler; hydraulic twin spinner manure spreader; discs û two types; harrows; MF Seeder; Cambridge Roller and Duncan Rotatiller.

Jan 1, 1991

By Lenin Salazar Dulanto

La baja de precios en algunos minerales ha obiligado que las empresas mejoren su proceso productivo a través del uso de equipos de última tecnología en los procesos de mecánica, hidráulica, electricidad y electrónica, así como en la eficiencia en el corte y taladrado, extracción y transporte. Sin embargo, tanto el desatado y sostenimiento manual desarrollaron un estréss y desgaste de energía en el trabajador. En este sentido, el presente trabajo señala una nueva forma de realizar tales operaciones en el ciclo de minado de la empresa Milpo a fin de garantizar la seguridad física de los trabajadores y equipos.

Jul 31, 2003

By R. M. Spang

Abstract Between the German city of Dresden and the Czech capital Prague a 4-lane highway is under con-struction. At the outskirts of Dresden it will cross the narrow and deeply eroded Weißeritz Valley by a bridge. Two twin tube tunnels under oblique angles join the bridge out of the rocky valley flanks. The different geotechnical conditions of these 4 tunnel portals, their design and construction are described within this publication. The two southern portals of the tunnel Dölzschen are situated within a vertical 65 m high former quarry slope, 25 m above the valley floor. The slope proved instable due to toppling failure and exposed serious rockfall risks. Systematic anchoring, scaling, rock bolting, netting and filling under extreme access conditions eliminated these risks. Tunnel excavation started from the slope surface without any pre-cut or conventional portal construction. The opposite northern portals of the tunnel Coschütz are situated in more gentle rock slopes. After removal of debris, excavation of the eastern tunnel started in a 30° slope striking oblique to the driving direction, without any precut, too. Because of the gentle slope inclination the cross section was not earlier completely covered by rock than 30 m behind. The western tunnel started from an optimized short, narrow and steep precut. Its flanks were stabilized by reinforced shotcrete and rock bolts. Because of the small distance between the tubes rock bolts were drilled into the cross section of the neighboring tunnel. Tunnel excavation was made by drill and blast operation, preliminary support consisted of steel arches, reinforced shotcrete and radial rock bolts. Thorough survey of the bolt’s coordinates and direction prevented them from meeting each other. Rock bolts were of the permanent type to prevent the final lining from being obliquely loaded. Systematically arrayed measuring devices checked deformations of slopes and tunnels. Zusammenfassung Der Neubau der Bundesautobahn A 17 wird Dresden und Prag miteinander verbinden. Die vierspurige Autobahn quert westlich von Dresden das enge und tief eingeschnittene Tal der Wilden Weißeritz mit einer Brücke. An beide Brückenwiderlager schließen mit schiefwinkligem Anschnitt doppelröhrige Tunnel an, deren Portale in den felsigen Talflanken liegen. Die unterschiedlichen geotechnischen Verhältnisse, die Überlegungen für einen jeweils optimalen Entwurf und der Bau der portalnahen bergmännischen Tunnelabschnitte sind Gegenstand dieser Veröffentlichung. Die Südportale des Tunnels Dölzschen liegen in einer vertikalen, 65 m hohen Felswand, 25 m über dem Talgrund. Die Felswand erwies sich als global kippgefährdet, außerdem lagen flächig verteilte erhebliche Steinschlag- und Felssturzrisiken für Bau und Betrieb vor. Die Kippgefahr wurde durch ein Systemraster aus vorgespannten Felsankern, die Steinschlag- und Felssturzrisiken durch bergsteigerisches Beräumen mit dem Brecheisen, Felsnägel und Steinschlagschutznetze eliminiert. Der Tunnelausbruch begann von einer Vorschüttung direkt in der Felswand ohne Voreinschnitt im Schutz einer kurzen Luftbogenstrecke. Die gegenüberliegenden Nordportale des Tunnels Coschütz befinden sich in wesentlich flacheren Hängen. Nach dem Aushub einer mehrere Meter dicken Abraumhalde begann der Tunnelausbruch der östlichen Röhre asymmetrisch mit einer Luftbogenstrecke in einer spitzwinklig zur Vortriebsrichtung streichenden, 30° mit dem Vortrieb steigenden Felsfläche, ebenfalls ohne Voreinschnitt. Wegen der flachen Neigung der Böschung war der Tunnelquerschnitt erst nach 30 m vollständig überdeckt. Für den Vortrieb der westlichen Tunnelröhre mussten erst eine zwischen den Röhren vorhandene Felsnase teilweise abgetragen, die westlich anschließende zurückspringende Felswand vertikal gestellt und gesichert und Felsaushub in der rechten Flanke getätigt werden. Der damit entstehende Voreinschnitt wurde so kurz wie möglich und ohne seitliche Arbeitsräume ausgeführt. Die Sicherung der Böschungen erfolgte mit bewehrtem Spritzbeton und Felsnägeln. Wegen des geringen Abstands der beiden Röhren wurden die unteren Lagen der radialen Ausbruchsicherung durchgeankert. Der Tunnelvortrieb begann im Schutz eines geankerten Portalkranzes und ebenfalls von einer Luftbogenstrecke aus.

Jan 1, 2003

Kinetic Dependence of Refractory Gold Sulfide Biooxidation Using Different Microorganism Association In this investigation, refractory sulfide concentrate from a deposit located in northern Russia was treated using biohydrometallurgical technology. The objective of this work was to compare the accelerated refractory sulfide concentrate biooxidation abilities of the pure and mixed mesophilic and moderately termophilic acidophiles cultures. Pure culture of Acidithiobacillus ferrooxidans and two associations of the: Acidithiobacillus ferrooxidans + Acidithiobacillus thiooxidans and Acidithiobacillus ferrooxidans + Acidithiobacillus thiooxidans + Leptospirillum + Sulfobacillus were used in this investigation. Results of sulfide concentrate bioleaching were analysed using the enzyme catalysis theory. Different effective kinetics parameters were calculated for Michaelis-Menten equation, such as Michaelis' constant and maximum rate of the enzymatic reaction. It was shown that the increase of microorganisms' species decreased Michaelis' constant. Lower Michaelis' constant characterises increasing bacteria ferment affinity to substrate (treated concentrate). As a result, the rates of sulfide minerals biooxidation have increased. This investigation has demonstrated that cultures of the different microorganism species, including moderately termophilic, allow to enhance different parameters of the biohydrometallurgical technology for the refractory gold sulfide concentrate treatment. We can see that bacterial leaching stage duration decreased and sulfide minerals oxidation increased. When the bioresidues were subjected to the hydrometallurgical stage, which includes aeration and sorption cyanidation, the operation factors were also enhanced. The decrease of aeration duration and the growth of the precious metal extraction by sorption cyanidation was achieved. Cyanide consumption was also reduced. The results of this investigation were used in design of an industrial plant.

Sep 13, 2010

William Frederick McBryde Broun, a graduate of the Royal School of Mines, was employed on the staff of the Mount Morgan Gold Mining Company for some years prior to 1912, and will perhaps be remembered by some of those who attended the Mount Morgan meeting of the Institute in 1910, as an Associate Member present on that occasion. He severed his connection with the Mount Morgan Company in 1912, and was returning to England via the East Indies, when he contracted typhoid atSingapore and died at Colombo.Years later some old papers were being turned out in the office where he had worked, when a set of M.S. notes in his unmistakeable handwriting came to light. On examination these appeared to be the rough draft of a paper he must have beenpreparing for the local branch of the Institute, which he had not been able to complete. The notes were very rough. Apparently it was the author's intention to fill in numerous gaps with extracts from sundry published articles on Cornish mining; theextracts were missing and only the written portions linking them together were there. They give a sketch of Cornish mining practice which those who wish may supplement (as the author would have done) from Le Neve Foster and other well-knownsources. The fragmental notes which have been pieced together as carefully as possible by Mr B G Patterson, Hon Secretary Mount Morgan Branch; are as follows :-The first mine the author worked at was Carn Brea, in 1904."This is one of the largest tin mines in Cornwall, and belongs to the Carn Brea and Tincroft Mining Co, which also owns Cooks Kitchen. The mine was started in 1832, but had been in a bad way for several years previously, and had just begun to recover...

Jan 1, 1919

By Yanjie Liang

Elemental sulfur and volatilization kiln slag(VKS)containing heavy-metal produced by smelter factories were used to produce sulfured building material. The effects of heating mode, material proportion (MSulfur:MVKS), size of waste particles and ratio of aggregate to filler(A/F) on the mechanical properties and leaching toxicities of solidified stuff were investigated. The optimal conditions for the solidification are stepped heating mode, 3:7 ratio of MSulfur to MVKS, particle size less than 150µm and 3/17 ratio of A/F. Under the above optimal conditions, the compressive strength of solidified stuff rises to 35 MPa, and water absorption is down to 4%-6%.Furthermore, when NaOH is applied as an additive in the process of solidification, the 2+concentrations of most heavy metals except Pb have reached the national leaching toxicity standard. The results of X-ray diffraction reveal that sulfured solidification is caused by the physical encapsulation rather than chemical transformation.

Jan 1, 2010

By John J. Sammarco

The mining industry has the highest average annual fatality rate among major U.S. industries. To address this, the National Institute for Occupational Safety and Health, Pittsburgh Research Laboratory (PRL), is conducting major research programs to reduce the hazard exposure of miners. One of the recently concluded programs at PRL developed the enabling technology for remote-controlled mining. An application involves the manual process of extracting and hauling coal where operators, in the tight confines of a mine, can be struck or caught by mobile machinery. The approach to remedy this problem uses a guidance system on the continuous haulage equipment so that it follows the continuous mining machine that extracts coal. This, in essence, involves sensor-based docking of the machines. Sensors functioning in the hostile mine environment of dust, methane gas, and water play the key role. Computer analysis of the mining machine's movements and empirical machine characterizations established operating requirements and spatial limitations to ensure proper loading of coal into the haulage equipment. These data served in the selection of a guidance sensor. Technologies such as scanning laser systems and ultrasonic sensors have frequently been used in other applications, but were found unacceptable. However, a near-infrared sensor employing active targets met the requirements. The sensor has a nominal 75b conical field of view and a range from 0.1 to 18.0 m. For the single-target mode, nominal range accuracy was 4.3% at a distance of 3.65 m. Correction algorithms were generated, which reduced the error to 0.6%. Airborne dust testing showed less than an additional0.8% accuracy (worst case) degradation at dust levels up to 15 mg/m3. Using four targets, the nominal range accuracy was 0.4% without correction algorithms. Analysis of dynamic testing of a continuous miner and haulage showed that accuracy was maintained and total target loss did not occur. A guidance system for the haulage system to follow the mining machine does not exist commercially. Such a system can reduce fatalities, injuries, and exposure to dust and noise.

Jan 11, 1998

By Terry J. Close

A mineral resource survey of the 940-square-mile (2,434 km2) Hells Canyon study area, which includes Hells Canyon Wilderness, Snake and Rapid Wild and Scenic River's, and adjoining roadless lands in Oregon and Idaho, indicates the area is highly mineralized. Thirty-four lode deposits within the study area have resources totaling about 31 million tons (28 million t) containing copper, silver, zinc, gold, and lead; another 42 lodes, not sufficiently exposed to allow resource estimates, are believed to have mineral potential. The most important deposits are copper-, silver-, zinc-, gold-, and lead-bearing volcanogenic occurrences, followed by silver-and copper-bearing contact replacement (tactite) deposits; other lode occurrences are relatively unimportant. The most important placer deposits occur at Dry Diggins; placers along the Snake River are small and scattered. The study area has extensive deposits of limestone and sand and gravel; it has little potential for energy resources.

Jan 1, 1982

By Nutter R. S.

A methodology has been developed for qualitative safety hazard evaluation and quantitative reliability analysis of mine monitoring and control systems. Detailed application of these techniques were made to two commercial monitor/control systems and to a West Virginia University distributed microprocessor-based system. A controlled environmental test was conducted on a set of one of the commercial system's outstations. A software reliability evaluation methodology was also developed and applied.

Jan 1, 1982

By Harvey Patashnick

Current state-of-the-art microweighing technology represented by the Tapered Element Oscillating Microbalance (TEOM) is utilized as the basis for a new generation of Personal Dust Exposure Monitors (PDEM's). Two design configurations are presented. The first is an end-of-shift analysis system which uses small TEOM-PDEM cannisters that replace the filter cartridges in the current PDEM system. All other components carried by the miner (cyclone preseparator and pump) are the same. After the shift the TEOM cannister is plugged into an interface box which enables a minicomputer to automatically identify the unit, determine the dust mass increase during the shift, compute the shift average dust mass concentration, and print out and/or store the data. The second design is a real-time TEOM-PDEM system which is capable of operation over a 10-hour shift and on demand display real-time dust concentration level, time weighted average, and shift average concentration. As a result of the design study, a prototype end-of-shift analysis system was fabricated and delivered to the Bureau of Mines. A description of this system which consists of six TEOM cannisters, interface electronics and minicomputer is given. The system represents a significant advance in the dust monitoring program in terms or accuracy and automation.

Jan 1, 1983

By Steven W. Schmauch

The Farlin Creek study area encompasses 610 acres managed by the Bureau of Land Management in Beaverhead County, Montana. A mineral survey was conducted by the U.S. Bureau of Mines and U.S. Geological Survey in 1984. Bureau of Mines personnel reviewed literature and county mining records, and examined prospects or mineralized areas to determine its mineral potential. Geological Survey personnel evaluated the area by geochemical sampling and geophysical surveys. The study area is included in the Mount Baldy mining district. Nearby mineralized Quartz veins or tactite bodies apparently do not extend into or exist within the study area. No significant gold or economic detrital minerals were found in samples from streams draining the area. All of the study area is leased for oil and gas.

Jan 1, 1985