Search Documents

Triboelectrostatic Producing Ultra-Clean Coal

Sep 13, 2010

By J. S. Roberts

"Campbell mines has been in operation since 1948. Part of the process consists of roasting of a flotation concentrate which contains arsenopyrite.At present operation level the milling rate averages about 850 t.p.d. and about 48 t.p.d. of concentrate is roasted. The gas emissions at present contain between 3 and 3.5 t.p.d. of arsenic trioxide, about2 - 2.5 t.p.d. of particulate matter and between 19 - 25 t.p.d. of sulphur dioxide. The particulate is extremely fine calcine dust and it assays about 4 oz. Of gold per ton.Until 1974 the gas was discharged untreated through a 125' stack.UntreatedThe decision was made in 1972 to erect a gas treatment plant, construction ran through 1973 and operation began in 1974. The cost of the installation was about 1.3 million dollars.On investigation the process technology, it was apparent that the plant operated by giant Yellowknife for the same purpose was the model we should study. I would like to acknowledge the fine cooperation we had from giant, the plant that emerged is very similar to theirs and incorporates some improvements suggested by them and based on their operating experience.The plant is designed to remove arsenic and solid dust and it has no provisions to remove sulphur dioxide.We depend upon the 125' stack to assure adequate dilution. Because of the nearby airport the stack cannot exceed 125'. A stack burner is provided that can ""y used to heat the stack gas and carry it higher into the atmosphere when there is an inversion condition.The removal of arsenic from hot gas is fairly simple. The sublimation point is about 425°f, a few degrees above this point the arsenic is a gas and a few degrees below it condenses into a solid form. The arsenic could have been removed by simply dropping the temperature below the condensation point and collecting all the solids in a baghouse. This would have removed the possibility of recovering the gold in the calcine dust and would have produced an impure and more bulky arsenic material to be placed in safe storage. The decision was made to collect the solid dust in a hot electrostatic precipitator operating above the sublimation point and subsequently lower the temperature below the condensation point and collect the arsenic in a baghouse."

Jan 1, 1976

By A. Sand

A 2-dimensional computational model based on the discrete element method (DEM) is utilized for modeling of stamp-charged coke making. In this process, a large volume of coal is compacted to one single coal cake before entering the coke oven. Cake densification and mechanical strength development are key factors for the subsequent production of a high-quality coke. An approach is introduced for model calibration utilizing multiple control parameters obtained from a laboratory-scale stamping device. Experimental data on stamper rebound amplitude, attenuation and peak force are compared with simulation output in a pairwise manner by constructing a criteria space, which allows identification of model settings best satisfying the control parameters. The calibration procedure carried out by multiple criteria comparison aided model parameter selection for reproducing stamper behavior in response to the properties of the cake subjected to compaction. This modeling and calibration procedure offers possibilities for numerically studying the densification and mechanical strength development of coal cakes. However, the approach is also more widely applicable to other compaction processes.

Feb 27, 2013

By E. LaRocque

"Long term contracts requiring delivery of 6,000,000 pounds of U308 per year to its customers have made it necessary for Denison Mines to expand its milling capacity from 7,100 tons per day to 15,000 tons per day.Previous papers (1) and (2) described the old leaching and product recovery practice. The flowsheet briefly includes a crushing and grinding circuit, sulphuric acid leaching in a Pachuca plant, liquid-solid separation with wash thickeners and two-stage drum filtration, concentration and purification by moving bed ion exchange followed by two-stage precipitation to produce an ammonia yellowcake.No. 1 Shaft ore, about 4,000 tons per day, will be processed through the truck dump into the old crushing and grinding plant and through the old leaching plant. Ore from Stanrock (No. 3 shaft) will be hauled by truck and also processed through the truck dump as No. 1 shaft ore. Beginning in 1982, ore production from Stanrock will gradually increase until 1985 when some 3,000 tons per day will be milled from the source.A new 8,000 ton per day circuit was designed and constructed to increase the milling capacity to 15,000 tons per day. The new circuit is separate from the old one except that it coins together for the precipitation and tailings neutralization sections of the plant. The feed to the new plant will be from No. 2 shaft.The flowsheet is much the same as the old plant with the exception of the grinding circuit and the ion exchange plant. A semi-autogenous grinding (SAG) plant, unique in the Elliot Lake area, has been installed rather than the conventional crushing and grinding plant; the ion exchange plant is the stationery bed type.This paper describes the major equipment installed for the expanded grinding and hydrometallurgical plant."

Jan 1, 1982

By W. P. Diamond, S. L. Cario, F. Garcia, J. D. Byars, T. P. Mucho

The National Institute for Occupational Safety and Health (NIOSH) has been conducting research at a Pittsburgh Coalbed longwall mine to evaluate and optimize bleeder ventilation and gob gas venthole longwall methane control systems. Gas flow into these two methane control systems was investigated using a combination of Sulphur Hexafluoride (SF6)tracer gas studies and gob venthole pressure monitoring experiments. The insights gained from this research has facilitated the development of a longwall subsided strata methane control system conceptual model. This model provides the basis for design suggestions to increase the efficiency of the gob gas venthole system to permit the bleeder ventilation system to become a "safety net" for methane control.

Jan 1, 2000

By Garry Keizer

The Cortez gold mine is located in Lander County, NR, about 130 km (80 miles) southwest of Elko. Cortez Gold Mines (CGM) is a joint venture between Placer Dome US Inc. (60% operator) and Kennecott Corp. (40%). The claims that supply oxide and refractory ore feed to the Cortez milling facility are located in both Lander and Eureka counties. These include the Cortez and Horse Canyon deposits, all operated by the joint venture. Other deposits outside the CGM claim area include Fire Creek, Buckhorn, Gold Bar and Tonkin Springs. These deposits all occur along the Battle Mountain-Eureka Trend. History Mining in the Cortez district began in 1862 with the discovery of high-grade silver ores. Grades in the hundreds of ounces per ton occurred in an area 7 km (4.5 miles) southeast of the current CGM mill site. Underground mining through the Garrison and Arctic tunnels provided the bulk of the ore production between 1864 and 1895. To a lesser extent, the Mill Canyon area also supplied ore until 1930.

Jan 1, 1993

When xanthates or dithiophosphates are used as collectors in sulphide ore flotation, adsorbed species may be identified by gas chromatography of the volatile products formed during low temperature pyrolysis. For collector additions ,as low as 20 g/tonne of ore, pyrolysis of the flotation products usually gives' an olefin directly related to the particular xanthate or Aerofloat reagent used. The method is able to provide valuable qualitative and quantitative data relating to the extent of collector adsorption and the resulting changes in the hydrophilic or hydrophobic nature of the mineral surface.

Jan 1, 1974

By D. Bedell, J. Robitalle, D. Macgilliveray

Agnico Eagle (Cadillac Quebec, Canada) selected the new Eimco PEC E – CAT™ clarifier thickeners for their counter-current decantation circuit, which handles approximately 200tph leached gold/silver ore. The E-CAT is based on rakeless ultra-high rate thickening technology that originated in South Africa. Four 9m diameter and two 10m EIMCO E – CAT ultra high rate, rakeless thickeners were installed in the fall of 2000. Thickening and clarification performance has been excellent. Problems with level control have been resolved and the plant personnel continue to improve the operating control techniques. The CCD circuit is critical to the success of the operation and good recovery. Data will be presented showing the wash ratios and recovery achieved. A brief history of the operation and the decision to utilize the CCD system will be presented.

Jan 1, 2002

By F. Calizaya

The PT Freeport Indonesia‘s Deep Ore Zone(DOZ) copper deposit is located in the province of Irian-Jaya, Indonesia. Currently, a block cave mine is being developed around this deposit. Production is scheduled to start in year 2000 and to ramp up to25,000 tpd by year 2003. The air quantity requirement for this mine is equal to 780 m3/s. To supply this quantity, the mine will require five centrifugal fans (one 450 and four 750 kW fans). This study summarizes the technical aspects related to the installation and commissioning of one of these fans. The fan was installed on the surface in a parallel arrangement with two others. It has a design capacity of 240 m3/s of air at 2.2 kPa of static pressure. The study presents the installation details from the underground shaft excavation and portal development through fan testing and commissioning. It also presents the results of a monitoring system that was installed to determine the fan duties.

Jan 1, 2000

By James W. Cassie

The Snap Lake Diamond Project is located approximately 220 km northeast of Yellowknife, NT, Canada at an approximate latitude of 63?35?. The project location is within the zone of continuous permafrost; measured ground temperatures are about ?2?C at 10 to 20 m depth below surface. The site is located on a peninsula jutting into Snap Lake. The site is generally barren of vegetation, except for some isolated areas with low trees located in topographic lows and near the shoreline of Snap Lake. As part of phased evaluation process with regards to the mining project, an Advanced Exploration Program was undertaken in 2000 and 2001. This program included the underground extraction of a bulk sample of kimberlite, which was processed on site. A Processed Kimberlite Containment (PKC) area was required as part of this program. The area chosen as the PKC facility was a small inland lake, called Inland Lake #1, on the peninsula. Construction of the PKC area required the construction of two dams, one on either end of the lake. At the south end of the lake, Dam 1 was constructed partially on a talik and partially on continuous permafrost. Dam 2 was constructed entirely on permafrost. The effects of the remote location, selection of suitable construction materials and permafrost conditions on the designs of the dams are discussed. A description of the design elements and construction schedule are provided. A review of the performance of these two dams, in terms of settlement, deformations, pore pressures and thermal regime, over the last several years is provided.

May 1, 2003

By Thomas O. Glover

The mining industry of Cameroon continued to be dominated by crude petroleum. Crude petroleum production has become the most important facet of Cameroon's economic development. Oil production was estimated to be 6.3 million tons in 1983 compared with 5.2 million tons in 1982 and 4.3 million tons in 1981. Over two-thirds of its export income was attributed to crude oil. The country's only refinery, dedicated in 1981, has a production capacity of 2 million tons. Cameroon has become self- sufficient in petroleum products since commissioning the refinery. The oil sector contributed approximately 13.5% to Cameroon's gross domestic product in 1982-83. Oil production was expected to rise from 125,000 barrels per day in 1983 to 156,000 barrels per day in 1985 when output peaks. Cameroon's ultimate recoverable reserves have been calculated at 100 million tons, or 750 million barrels of oil.

Jan 1, 1985

By Jan E. Nesset, James A. Finch, Frank Rosenblum, Rebecca Payant

"Under certain conditions of moisture and oxygen, sulphides can spontaneously heat, a phenomenon known as self-heating. In this paper, we test a hypothesis that galvanic interaction between some sulphides can promote self-heating. Galvanic interaction is controlled by restpotential difference between minerals and their surface area of contact (particle size). In order to decrease rest-potential, four sulphides were tested: pyrite, chalcopyrite, sphalerite and galena. Two series of samples consisting of mixtures of two sulphides, each representing a mass fraction of 50 %, were run in standard self-heating tests. The first series comprised five mixtures, two with low rest-potential difference (pyrite-chalcopyrite and chalcopyrite-sphalerite) and three with high rest-potential difference (pyrite-galena, chalcopyrite-galena and pyrite-sphalerite). The second series was performed on a pyrite-sphalerite mixture at four particle sizes (80 % passing 850 µm, 300 µm, 75 µm and 38 µm). The first series showed that the individual sulphides and the mixtures of low rest-potential difference did not self-heat but the mixtures of high rest-potential difference did self-heat. The second series showed that self-heating increased inversely with particle size (increased specific surface area) and revealed that it was the fineness of the pyrite (high rest-potential sulphide) that governed the self-heating effect, indicating the rate-limiting step is the reduction reaction on pyrite (cathodic mineral). The increase in self-heating with high rest-potential difference and increasing particle fineness supports the hypothesis that galvanic interaction contributes to sulphide self-heating. A possible mechanism based on the hydrogen sulphide hypothesis is proposed where the reduction reaction at the cathodic mineral surface is ferric to ferrous. The understanding gained will be of interest to those involved in storage, shipping and disposal of sulphide minerals.INTRODUCTIONSulphide mineral ores are the major source of most base metals such as copper, zinc, nickel and lead. Once the ore is extracted, the sulphide minerals are liberated by size reduction (crushing and grinding), concentrated by flotation, and the concentrates sent for further processing to extract the metal (smelting and refining). At the various stages from mining to concentrate shipment and tailings storage, the sulphides are exposed to a variety of environments, which under certain conditions of air (oxygen), humidity and temperature can cause them to heat. Since no external heat source is involved, this pyrophoric process is known as spontaneous heating or, more commonly, self-heating. The self-heating of sulphides is associated with oxidation reactions under moist conditions. If the heat generated is greater than the heat dissipated, the sulphides will self-heat and the material temperature will rise. This can make working conditions potentially dangerous as oxygen is consumed from the surrounding air and significant quantities of sulphur dioxide (SO2) can be released (Ninteman, 1978)."

Jan 1, 2011

By Kazimierz Gwizdala

In the paper the method for estimation of settlement of vertically loaded piles in a group is presented. The method is generally based on the hybrid procedure with non-linear solution for single piles and with interaction between them for the low-strain shear modulus. Some attention is paid to the influence of deformation and strength parameters used in calculations. The applied model is verified in the framework of the research programme carried out recently in the Geotechnical Department of Gdansk Technical University. It concerns monitoring and analysing the settlements of the existing structures on piles. A comparison of calculation and measurements results for two tested buildings is presented as an example.

Jan 1, 2002

By H. C. de Wet

The predevelopment and preparation of a total infrastructure in a deep level mining environment, prior to the shaft system being commissioned has major advantages. This paper intends to indicate these advantages and outline an understanding of the disadvantages. These benefits can be classified in three basic groups: the financial and timing advantages, a knowledge of the ore body and the development of required technology to meet the design parameters. The required technology in many aspects was still to be developed prior to successful application. Stemming from the technological evolution are some secondary advantages which will be described in each of the groups. Safety and health considerations and some practicalities made some of the new technology redundant prior to the actual application. In each case the actual achievements and the anticipated benefits will be indicated to allow the reader to distinguish clearly between planned and actual achieved advantages.

Jan 1, 1997

Open cast mining has been practiced in South Africa since the late1970s under near ideal geotechnical conditions. In the past decade, with the exhaustion of the traditional South African coal fields, geotechnical conditions have deteriorated. In addition, the nature of the open cast coal mining industry is changing from the conventional strip mining of virgin coal seams to the extraction of underground coal pillars by buffer blasted highwalls. These industry changes have resulted in the need to re-examine the manner in which geotechnical engineering is applied to highwall design. This paper proposes a geotechnical design rationale for open cast highwalls. Furthermore, the rationale takes cognizance of the various geotechnical hazards associated with conventional strip mining and pillar extraction by buffer blasted highwalls. The need to use geotechnical domain models and blasting geotechnics, as proactive tools for rock fall reduction, are also discussed.

Jan 1, 2001

By C. M. Badeen, J. Paige, W. Evans, L. McCauley, A. Caddies, I. Alilovic, R. Turcotte, C. O. Lyogun, C. Bonner

Gear pumps are very commonly used for the pumping of AN-water based emulsion products for both handling and blast loading applications. The potential major hazardous problems likely to be encountered with these pumps are: (i) high probability of friction; (ii) possibility of product confinement in the area of the bushings; (iii); high bearing failure rate; (iv) pump running dry; (v) presence of foreign material; (vi) deadheading of pump; (vii) delamination of elastomer from steel gears. Of all these possible scenarios, the no-flow situations where the pump is running dry or deadheaded have always been recognized as the most serious ones.

Jan 1, 2015

By Svato Prochazka

Content: ? commonly used drive systems ? drive system efficiency ? introduction to SR technology ? SR drive system advantages Commonly Used Feeder Drives Technologies ? VFD + induction motor ? hydraulic drive + hydraulic motor SR drive + SR motor

May 1, 2010

By P. J. Rider

Diamond Value Management?s objective is to achieve $/ton revenue improvement across De Beers group mines. The respective %improvement contributions are measured against targets set by each of the operations. Degree of target achievement is measured via a maturity model at each operation. DVM comprises seven elements. It spans several value chain facets and various collaborative projects are conducted under its umbrella. New technologies in De Beers are also evaluated from a DVM perspective.

Jan 1, 2003

By J. Dionne

"Next to the actual mine of Les Explorations Muscocho Ltée in Montauban, Quebéc, you could find a total of 364 000 tons of flotation tailings assaying 1.4 Au g/t et 82 g Ag/t to the south of the municipality. This tailings pile is what is left of previous operations. Preliminary leaching tests on these tailings in laboratory columns gave interesting results which led to tests in larger columns in 1984 and to a pilot test on a 750 ton heap in Montauban during the summer of 1985.This paper briefly describes the columns tests performed at the Centre de Recherches minérales and the heap leaching test designed and conducted by SOQUEM in Montauban. It also presents the results obtained.RESUMEPrès de la mine actuelle de Les Explorations Muscocho Ltée à Montauban, Quebéc, se trouvent, au pied du village, 364 000 tonnes de rejets de flottation titrant environ 1,4 g Au/t et 82 g Ag/t. Ce tonnage de rejets représente ce qui reste de l'opération des anciennes mines de Montauban.Des essais préliminaires de lixiviation en colonne sur ces rejets ont donné des résultats encourageants. Ils ont été suivis en 1984 par des essais en colonnes plus volumineuses et par un essai pilote à Montauban en 1985 sur une pile de rejets de 750 tonnes.Ce te x te donne une brève de script ion des essais en colonne effectues au Centre de Recherches minérales et de l’essai pilote planifie et exécute à Montauban par SOQUEM. Il présente les résultats obtenus."

Jan 1, 1987

By G J. Lyman, F S. Bourgeois

As the prices of metals slide, financial control of mineral processing operations becomes more and more important. Control of a mineral processing operation implies measurement of grades, recoveries and losses, with every effort being made to recover more product from the same feed. Shareholders become more concerned with the transparency of the operations and the corporate governance.There is only one way to achieve this and this is by sampling and making good use of the results of that sampling. Sampling systems that provide only 'rough' figures are not good enough. Similarly, a competitive position in the marketplace demands close control of product quality. Maximisation of product output demands that the product just meet the specification so that product yield is maximised. Decisions based on precise sampling results carry less risk that those based on imprecise results.This paper reports some recent advances in sampling theory that permit full quantification of sampling distributions, not just the sampling variance as has been possible in the past. These advances can be used together with simulation methods to tie down sampling precisions and develop calculations that quantify decision making risk when using the sampling results. A number of examples illustrate the use of the new advances and a final example indicates the development of risk analysis curves in the coupling of sampling precision to sale of a commodity.CITATION:Lyman, G J and Bourgeois, F S, 2015. Sampling, corporate governance and risk analysis, in Proceedings MetPlant 2015, pp 27–34 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015