Search Documents

By P. N. Mohan Das, K. Harikrishna Bhat

"The major ilmenite reserves are located in India at Chavara (CH), Manavalakurichi ( MK) and Chatrapur, Orissa (OR). India stands first in terms of ilmenite reserves, which are estimated to be 278 million tonnes out of which, 142 million tonnes are processable. Mineralo-chemical analysis showed that Chavara ilmenite is the most weathered one with about 60% TiO2 while Chatrapur is the least weathered with about 50% TiO2. XRD and SEM studies of different magnetic fractions of these three mineral deposits established the co-existence of ilmenite with pseudorutile, rutile and haematite phases in substantially varying amounts. It is observed that the tropical weathering rather than the source rock difference has apparently played an important role in imparting major compositional and structural dissimilarities among the ilmenites in different places. Further, the chemical analysis, XRD and SEM characterisation of differently weathered samples of MK ilmenite separated by the magnetic fractionation showed that the degree of alteration was invariably associated with the decrease in magnetism, increase in the rutile phase and the change in Fe2+/Fe3+ ratio of ilmenite grains. Magnetically separated fractions when subjected to metallisation with carbonaceous reductant such as coke showed that the degree of reduction increases with the degree of alteration and with the decrease in the Fe2+/Fe3+ ratio.In the processing of ilmenite through the Becher process, aeration rusting of pre - reduced ilmenite is found to be the rate-limiting step thus, affecting the productivity and economy of the process. Investigations have proved that the addition of some organic compounds such as glyoxal, sucrose etc., to the system accelerates the reaction to such an extent that the rusting time has been reduced to less than half. The formation of acids by the these organic compounds during the rusting reaction was proved responsible for maintaining the pH of the solution in the range 3-4 at which iron hydroxide do not precipitate and block the pores in the reacting surface of the grain."

Jan 1, 2003

By Patrick A. Turner, Timothy J. Olson, Abraham J. Schutte, Roman van Ommen

"The use of classifying devices in grinding circuits dates back to the early 1900’s when classifiers were installed to close ball mills. The search for ways to further improve grinding circuits led to the use of hydrocyclones in place of mechanical classifiers in South Africa in the early 1950’s. Today Hydrocyclones are considered as the best classifying devices to close grinding circuits. After 50 years of development the hydrocyclone has changed significantly when compared to the designs of the early days, but the focus to circuit optimization must be expanded to an understanding of the integral system consisting of mill, cyclone feed pump and cyclone.The key to good cyclone circuit design and operation in primary grinding circuits will be discussed including individual cyclone design features such as cone angle or materials of construction, as well as orientation and manifold configuration.Cyclone performance issues as well as maintenance considerations will be detailed in an effort to achieve consistent cyclone operation with minimal coarse solids in the overflow. “The importance of constant cyclone feed conditions is unquestioned today. The challenge of Cyclone sizing is a large number of not fully known variables prior to startup. The most significant unknown variable is slurry viscosity. Because of this, engineers often specify a conservative cyclone system that produces a finer than required separation. However, this approach often leads to higher circulating loads and a higher overflow density in order to produce the required separation. The higher cyclone overflow density results in a less efficient cyclone separation. The average concentrator can pick up 2-4% finer overall grind by having a more aggressive cyclone operation.”"

Jan 1, 2003

By Kal Sastry, Anshuman Prasad

"Agglomeration of fine iron ore concentrates is carried out in two steps:Balling, which refers to the production of green pellets by tumbling moist fines powders in drums, discs, or cones, and Induration, which refers to the subsequent thermal treatment of the green pellets in straight grate or grate-kiln systems.This paper addresses computer simulation of balling or green pelletization step. The process of agglomeration from a mechanistic point of view can be described as the transformation of moist feed to well-formed species or pellets. The moist feed is composed of fines of infinitesimal size while well-formed species are of finite size and number. These well-formed species undergo changes in their size and number through different mechanisms of agglomerate formation and growth. Nucleation, coalescence and layering are the three main mechanisms that describe the formation and growth of granules during an agglomeration process. A population balance equation enables quantitative description of the evolution of agglomerate size distribution due to the occurrence of each of the mechanisms.A numerical solution for the population balance model is necessary and is obtained by the use of a sizediscretization approach. The numerical solutions provide a suitable basis for the analysis of the agglomeration process. Also a coalescence kernel has been introduced that is capable of describing the simultaneous occurrence of nucleation, coalescence and layering mechanisms. The effect of feed moisture has been described using a moisture factor with an exponential functional dependence on the moisture content. The effect of the feed to seed ratio is modelled by the introduction of a crowding factor. It was assumed that only the feed particles which are much more in number experience a crowding or restricted in space interactions effect. A computer simulation program has been developed with MATLAB as the simulation language."

Jan 1, 2003

By Stoyan N. Groudev, Ioannis Paspaliaris, Plamen S. Georgiev, Irena I. Spasova, Kostas Komnitsas

"The uranium deposit Curilo located in Western Bulgaria for a long period of time was a site of intensive mining activities including both the open-pit and underground mining techniques as well as in situ leaching of uranium. The ore was rich in pyrite and, apart from uranium, contained some non-ferrous metals. The mining operations in the deposit were ended in 1990 but since that time the deposit is a permanent source of acid drainage waters. The generation of these waters is connected mainly with the oxidation of pyrite and other sulphide minerals by the indigenous acidophilic chemolithotrophic bacteria.Laboratory and pilot-scale studies revealed that an efficient clean-up of the above-mentioned waters was achieved by means of passive systems of the wetland type. In 2001 a wetland was constructed in the deposit to treat a portion of the acid drainage waters which were discharged to a small ravine. This ravine reaches into the Teina, a small river that is a tributary of the upper reaches of the Iskar river.The wetland was constructed in the ravine and its bottom was located on intrusive rocks with a very low permeability. The rocks were covered by a 30 – 50 cm layer consisting of a mixture of soil, plant compost and crushed limestone. The wetland was characterized by an abundant water and emergent vegetation and a diverse microflora. Typha latifolia, Typha angustifolia and Phragmites australis were the prevalent plant species in the wetland but species of the genera Juncus, Eleocharis, Carex and Poa as well as different algae were also well present.The acid drainage waters treated by the wetland had a pH in the range of about 2.5 – 4.1 and contained uranium, radium, some heavy metals (iron, manganese, copper, zinc, cadmium, lead), arsenic and sulphates in concentrations much higher than the relevant permissible levels for waters intended for use in the agriculture and/or industry. The watercourse through the wetland covered a distance of about 0.2 – 1.0 l/s."

Jan 1, 2003

By Rebecca Hope, Derick Moolman, Frikkie Malan

"Despite the lip service that has been paid to pro-active plant maintenance processes over recent years, a significant portion of maintenance in industry is still reactive. The business driving force to prevent expensive production opportunity costs arising from “break-down maintenance” is obvious. Various benefits can be derived from successfully deploying remote equipment diagnosis technology and associated business processes.From an end-client’s viewpoint these include the ability to predict and take actions to prevent equipment breakdowns, increasing the lifetime of equipment by responding to appropriate operating instructions and therefore improving the return on capital expenditure. Better planning and scheduling of maintenance priorities and resources with performance measures like an Equipment Health Index are also possible. The knowledge that a qualified supplier engineer is constantly in touch with the operating conditions of their equipment, albeit remotely, is more than a comfort, and can be translated into quantifiable cost savings and improved supplier service levels."

Jan 1, 2003

By P. K. Sen, Mrinal K. Ghose

Tailing slurry is usually abrasive and possesses high viscosity. This paper examines the existing iron ore beneficiation process and focuses on some of the key environmental issues related to the disposal of tailings. It identifies that almost 32% of the iron ore extracted ends up as tailings and they are usually disposed in slurry form in tailing ponds. By the year 2000, 27 Mt of iron ore tailings were generated in India, which has become one of the biggest waste handling problems to the industry. Characteristics of the tailings vary widely. So the physical nature of tailings cannot be considered separately in isolation without considering the mill effluent from the beneficiation plant. In the present investigation, studies were carried out in three iron ore mines in India to evaluate the characteristics of tailings from the beneficiation plant. The tailing samples were collected from different locations during a time period of one year and analyzed. The results will be discussed and the characteristics of the tailings have been evaluated. The disposal system of tailings at the three mines was evaluated. The research on the settling characteristics of tailings indicates that the area provided in the existing tailing ponds in India is much more than that of the experimental results. This paper concludes that sedimentation tests are essential to design appropriate tailings pond with respect to size. In the proposed scheme it is suggested that an additional unit process, i.e. sedimentation tank be added to the process before the disposal of tailings to the tailing pond.

Jan 1, 2003

By Paul W. Weiblen, Louis J. Cabri, Rolando Lastra

"Preliminary tests were done to determine whether comminution by electric-pulse disaggregation, or EPD (cf. Rudashevsky et al; 1995), was more effective than using conventional crushing for Merensky Reef ore. A hand sample of the Merensky Reef was sawn in two: then one sub-sample was comminuted to – 2 mm using E-PD at the University of Minnesota, and the other sub-sample was crushed to –2 mm using a conventional jaw crusher at CANMET.The products of the electric-pulse disaggregation and jaw crusher were fractionated by sieving and by a separation using a heavy liquid with a specific gravity of 3.3, because the proportion of platinum-group minerals (PGM) and sulphides to silicate minerals is very low. Thus, four mineral separates were produced: –2000 + 833 µm, -833 +208 µm, -208-µm float and -208-µm sink. All the mineral separates were studied by image analysis (Lastra et al; 1998). The main objective was to determine the liberation of gangue (silicate minerals), chromite, pyrrhotite, chalcopyrite, pentlandite and PGM. In the case of the PGM, a specific image analysis program was written to search and measure these minerals."

Jan 1, 2003

By Dominic Howarth, Diana Drinkwater, Don McKee

At a time when the mining and minerals industry across the world is undergoing unprecedented change, the very fabric of the tertiary education system which is the principal source of trained professionals to the industry is in decline in many countries. The change sweeping the industry is globalisation as evidenced by the emergence of a relatively small number of increasingly dominant corporations with operations in most of the major mining countries. The education sector is struggling to provide sufficient graduates as the viability of small mining schools declines. That is only part of the problem as the global operating industry is increasingly seeking graduates who are comfortable working in different countries and cultures. One obvious response to the industry needs and developments is for the education sector to consider how it can best respond to the global opportunities. This paper presents the case for a global education network which is based on a network of international thinking Universities and which makes use of the latest in educational thinking and technologies to provide a quality education and in the process produce graduates fitted for international careers.

Jan 1, 2003

By T. V. Chnyrenkova, J. Troncoso, V. A. Luganov, G. P. Kluev

"Arsenic-gold bearing ores are used as flux in smelting or are leached out with extraction of gold. For decreasing arsenic content in processed materials and for breaking up the lattice and opening up of gold the raw materials are roasted. Some regularity was established for sulfidizing of arsenic bearing compounds in a presence of pyrite and for oxidation of ores and concentrates in the presence of soda.This article analyses the results of laboratory and pilot testing of dissociating and oxidizing roasting of gold-arsenic bearing concentrates. During the dissociation roasting under vacuum arsenic is sublimated into elemental and sulfide forms. This process allows minimizing the negative influence on the environment but requires costly engineering solutions. Roasting in a limited quantity of oxygen in the gaseous phase makes it possible to sublimate arsenic in the form of oxides and sulfides and may be carried out in fluid bed furnaces."

Jan 1, 2003

By Briony C. Ruse, David V. Boger, Fiona Sofra1

"The sustainability of the mining industry must be addressed through improving tailings management. The use of thickened tailings and pastes stems from a paradigm shift towards designing tailings disposal sites to suit their surrounding environment, rather than manipulating the environment to accommodate the tailings. Thickened tailings and pastes usually exhibit non-Newtonian behaviour, so a thorough understanding of the rheological characteristics of the material is required in order to determine the disposal plant operating conditions.As environmental factors translate into economic issues, minimising waste production using dry disposal methods is gaining popularity. The use of rheological information is of high importance in evaluating the spreading characteristics, the transportation and the dewatering of thickened mineral tailings. The principles outlined may be applied to many industries encompassing a wide range of waste materials. The main obstacle to the widespread implementation of dry disposal methods has been the high initial capital cost of the methods due to the dewatering step, and the high cost of pumping thick suspensions across any great distance. Proper and thorough costing of tailings disposal activities combined with an accounting approach that shows closure and post-closure care costs on a per tonne basis of tailings disposed throughout the life of the tailings facility will show that dry disposal methods are more favourable than they might seem on initial appraisal."

Jan 1, 2003

By Wang Xiaotie, Yu Yongfu, Che Liping, Zhang Fuguang

The flotation process of native Rare Earth minerals such as bastnasite, monazite, mixed minerals of bastnasite and monazite, using the new effective collector Dh was studied in this paper, respectively, and the flotation properties are described. The good qualities of the new collector Dh were revealed through comparing with other collector of Rare Earth minerals. The test results of different ore samples show that at moderate pulp pH (8.5-9.5), Rare earth minerals can be effectively separated from barium, calcium and silicon bearing intergrowth minerals (barite, calcite and silicate minerals) and high quality Rare Earth concentrates can be obtained successfully by the new collector Dh, acid silica gel, turpentine and reagents fitting together rationally. In order to determine optimum technical conditions, the effect of pulp pH, pulp temperature, pulp density and the effect of dosage of reagents (Dh and acid silica gel) on the flotation were investigated in the test.

Jan 1, 2003

By James Y. Oldshue

"Very seldom is it possible when contacting a gas with a slurry to measure the dissolved gas concentration in the slurry, and even were it possible, seldom are equilibrium data available with a suitable Henry’s law constant.In general, by assuming a reasonable value for the dissolved gas concentration in the slurry and a corresponding equilibrium gas partial pressure P*, Kga values can be calculated for the pilot plant and scaled up. Then, with the same P* value at various reaction conditions, a mixer can be designed which is quite satisfactory, having a reasonable design factor for full-scale performance.We will take as an example a slurry of a known solids composition and use a continuous 4 tank system. By assuming a percentage saturation of the dissolved gas in the first tank, the dissolved gas concentration can be obtained in the other three tanks. It usually is possible to measure the off-gas composition in each of the 4 tanks. If the top of the tanks is connected in the form of a multi-compartmented horizontal autoclave, then a modified top off-gas composition in each compartment must be used."

Jan 1, 2003

By G. Demi, G. Belardi, N. Shehu, S. Cico

The physico-chemical interaction between minerals such as olivine, chromite and serpentine and the ions most commonly present in solution, like Ca and Mg and flotation reagents such as EDTA and oleic acid was investigated. The study was conducted via release tests, electrophoretic measurements and microflotation of selected minerals coming from the Kukes deposit (Albania).

Jan 1, 2003

By Gerke Gilian, Pretz Thomas, Pehlken Alexandra

"The evaluation of health hazards within the treatment of mineral and waste materials is gaining more and more importance in industrial countries. The need to control occupational safety has been recognised, and regulations which describe general protective measurements for personnel provide a tool to protect their health. It is the aim of the paper to give an outlook for practical approaches to risk assessment and to present measures for exposure reduction in accordance with the state of the art in Germany.Both the treatment of minerals and of waste materials are described in relation to the risk assessment. The method of evaluating health hazards in the two industries is similar and therefore both examples are presented next to each other.The example presented in the paper is the German “Biostoffverordnung” (the regulation for biological materials) which is important for the waste treatment industry. All kinds of waste treatment facilities (like composting facilities, waste dumps, sorting facilities for packaging materials) are obliged to carry out an assessment of health hazards for a variety of working areas and working places. The possible safety requirements deriving from this regulation are presented and discussed under the aspect of biological hazards.All over the world each country has different guidelines and regulations but all have one target in common – to protect the employees. This can be achieved through a good management system of occupational health and safety. Therefore the health hazards have to be known and assessed.Principles of the assessment of health hazards are described through:Data collection on siteData evaluationAssessment of health hazardsDocumentation"

Jan 1, 2003

By Victor Avdokhin, lvan Kovlekov

"Studies of the process of concentration of gold-containing sands and technogenic resources show that the main reason of gold losses is misbalance between size of gold particles and degree of roughness of mineral bed. This results in free circulation of small gold particles in pores with following washing off the particles from the bed by turbulent flows.We elaborated design of magnetic sluice, intended for improving efficiency of recovering fine gold by optimizing magnetic field of a magnetic system on the base of forming catching coat from magnetic mineralsThe magnetic sluice includes trough-shaped body from magnetic-conducting material. On the bottom of the trough, magnets are placed, and opposite poles of the magnets are oriented outwards. Thickness of the bottom is determined to be sufficient for locking magnetic lines of force of the magnets on each other. The magnets of rectangular plate shape are placed on the rough bottom, covering the whole surface or with spare areas; the magnets are placed across the trough with alteration of rows with the same pole orientation."

Jan 1, 2003

By Jim Petrie, Mary Stewart, Damien Giurco

This paper describes a generic approach to analysing the environmental and economic performance of a generic global mineral/metal value chain, with the express view of improving the quality of prospective decision-making within the industry in order to ensure more sustainable outcomes. As a point of departure we propose that it is not possible to place metals in the context of the sustainable development of society without paying due regard to the entire metals value chain. Thus, the starting point for this analysis is the development of a global stocks flows and transformations model, for the metal of interest. Any aspect of the value chain, e.g. “metals refining, “goods manufacture”, “use and disposal”, can be assessed, either relative to other stages in the value chain, or in more detail by focusing on the technologies used within that stage. The use of this model as a decision support tool is explored here for the case of copper. Both primary and secondary production routes are enumerated, covering a range of processes, for seven distinct geographic regions around the globe. The value of the modelling approach is explored for different energy mixes. In particular, the case study examines the impact of increased recycling on the (re) distribution of global and regional environmental impacts for technologies-in-place in these different regions. The aim of these case studies is to highlight to the minerals processing and metals refining industries their potential role in a more sustainable global society.

Jan 1, 2003

By Chris A. Fleming

"Interest in the recovery of cyanide from gold and silver plant tailings has heightened in recent years. This interest has been spurred by several factors:Increasingly stringent regulations throughout the gold producing world, governing discharge limits for free and total cyanide to tailings ponds and the environment.The increasing cost of active chemical treatment versus passive (natural degradation) treatment of tailing, to bring them in line with environmental regulations.The worldwide trend to processing of more complex gold ore bodies, which is usually accompanied by higher levels of cyanide consumptions and greater concentrations of cyanide (particularly the copper cyanide complex) in tailings.The growing negative perception of the general public for the gold mining industry, due to several highly publicized cyanide spills in recent years (breaches of tailings dams, accidents involving trucks carrying cyanide to gold plants, etc.).The ability to recover cyanide from gold plant tailings has been known almost as long as the cyanidation process has been practiced, but there has been little incentive to process tailings in this way in the past. With the development of technologies that make it possible to recover and recycle free or complexed cyanide directly from gold plant slurry tailings, which indicates, on paper at least, the potential for significant cost savings compared to cyanide destruction, coupled with the introduction of legislation to seriously limit the discharge of cyanide to the environment in most gold-producing regions of the world, many companies are evaluating the cyanide-recovery alternative."

Jan 1, 2003

By P. Huang, D. W. Fuerstenau

Various factors that control the natural flotability of talc, including differences due to crystal face and edge effects, were delineated. For study of talc depression phenomena, dextrin was used as a model depressant. For the enhancement of talc flotation, dodecylammonium acetate (DDAA) was used as the collector. The interaction of DDAA with talc was assessed by flotation experiments and electrokinetic (zeta potential) measurements, from which the role of hydrophobic bonding can be demonstrated. The results presented in this paper provide useful information on how the crystal chemistry and surface chemistry control the electrical double layer, adsorption phenomena, wettability, and flotation behavior of talc in aqueous media.

Jan 1, 2003

By Shailin Lalloo, Allan B. Nesbitt

"Gravity separation by centrifugal equipment, particularly in the mineral processing industry is a novel approach of optimising product recovery. The manufacture and sale of centrifugal equipment by recently established companies is now beginning to have a significant impact on the industry. Some benefits of operating at increased gravity include: reduced environmental issues, a shorter lead time, lower capital cost and improved recoveries of elemental mineral before entering the grinding circuit.Of topical discussion is the use of centrifugal separators for the recovery of less valuable minerals that will form a greater proportion of the feed compared to traditional scalping circuits where the gold content is extremely low. This ultimately results in the centrifugal system having to have a greater mass pull. In addition, the relative density difference between gangue and valuable mineral is likely to be less and therefore modelling and optimisation of this separation process will be necessary. Some researchers have muted using fluidisation models to model the forces present in the separation zone of a centrifugal separator2. It is not unusual for the manufactures of centrifugal separation equipment to use fluidisation terminology to describe what happens in the separation zone. Most fluidisation models are based on the empirical/classic relationship between superficial fluid velocity and voidage postulated by Richardson and Zaki. However, no researcher has proved the effectiveness of this relationship in an increased gravity Environment."

Jan 1, 2003

By P. B. Altringer

The Federal Bureau of Mines conducted a study to determine if residues from fractional distillation represent a potential source of mineral values. A literature review and discussions with tar sand specialists failed to disclose the mineralogical nature of residues remaining after bitumen extraction. To develop this information, pilot plant tar sand residues or toluene-cleaned tar sands from 23 deposits were examined. The nature of the residues was determined by standard mineralogical methods and the chemical compositions were determined by X-ray and ICP (inductively-coupled plasma spectroscopy). None of the sands or concentrates examined contained sufficient valuable minerals to be economically important.

Jan 1, 1982