Search Documents

By C. Sima, M. Legoabe

Keywords: Pyrometallurgy, furnace, platinum Mortimer Smelter is one of the three smelting operations in the Anglo Platinum Group. It is located in the Limpopo Province, approximately 100 km north of Rustenburg, and approximately 15 km west of Northam. The smelter operation is the smallest of the three smelting operations in the group, with a smelting capacity of 170 kt/annum. The operation consists of a Larox filtration plant, a Drytech flash drying plant, a modified Elkem / Hatch 19.5 MVA furnace, and a 60 t/h matte crushing plant. The operation does not convert its furnace matte, and hence the final sulphide rich matte is transported to and processed further at the Anglo Platinum Converting Process (ACP) within the Waterval Smelter Complex in Rustenburg. Furnace slag is granulated, and processed through a slag mill, or transported to a slag dump.

Jan 1, 2006

By Evelio N. Horta

The influence of soil improvement replacement area in foundation settlements is discussed for soil improvement methods used in Southeast Florida. A 3D Finite element analysis is used for two typical conditions in the area: foundations bearing on loose sands and foundations bearing on a crust of limestone underlaid by very loose sands. Particular attention is given to Jet Grouting as a soil improvement method. The potential impact of the stiffer jet grout columns on the structural foundation design and quality control issues are also discussed. It is shown that in loose sand conditions 15 to 20% area replacement produces substantial reduction in total settlements. Reduction in total settlements for mixed profile is less significant but the use of the method in those cases is directed to reduce punch through potential.

Jan 1, 2007

A model has been developed as part of the AMIRA P420 Gold Processing Technology Project to simulate the recovery of gold by centrifugal gravity devices. The model (which is available online) uses the simulation methodology developed by Laplante et al (1995) to predict gravity recoverable gold (GRG) recovery under varying operating conditions and circuit configurations. In addition to predicting GRG recovery, the model also predicts the GRG content and size distribution of the cyclone overflow and underflow. The predicted overflow GRG content and size distribution can be used as inputs for a leaching model in which size dependent leaching rates are applied for each size class of GRG and non-gravity recoverable gold (non-GRG) in the cyclone overflow, allowing size-by-size leach recoveries to be determined for GRG and non-GRG. The application of the gravity model and leaching model are demonstrated using a case study. The simulated gravity recovery and leaching performance showed excellent agreement with the measured values. The developed models can be used to assess the sensitivity of gravity gold and leach recoveries to varying feed GRG content, GRG size distribution, gravity circuit feed rate, classifier performance and leach residence time. The described methods can be used to optimise new and existing gravity and leaching circuits.

Aug 1, 2010

By S. C. A. Franca, M. T. Millqvist, A. B. Luz

Laboratory experiments were performed on a Brazilian diatomite from Bahia State to produce an industrial product for use as a filter aid. Bench and pilot plant tests were conducted consisting of: diatomite desegregation, organic matter and clay removal, filtration, drying and calcination. Calcination temperature and sodium carbonate addition influenced diatomite particle size distribution. Optimum filtration rates for calcined products were obtained at 900°C and 47 min. residence time with 3% (w/w) of sodium carbonate addition, and resultant products met specifications imposed on filter aids.

Jan 1, 2002

By M. G. Irish, E. E. Vidal, M. J. Jahraus, P. R. Taylor

An experimental system has been designed to monitor on-line variations of leaching parameters in a closed circuit of cyanide leaching solutions and gold bearing ores. Experiments performed to deter-mine variations in some important leaching parameters of the solution: pH, dissolved oxygen, free cyanide, oxidation/reduction potential, gold content, temperature, pressure and solution chemistry. By comparing results obtained when the leaching solution is allowed to become acid or kept basic, it was possible to infer the chemical reactions that occurred between the solution and the ores.

Jan 1, 2004

By J. Griesel, P. H. F. Bouwer, K. Bisaka

Transalloys produces 160 000 tons of SiMn per annum from five AC submerged-arc furnaces. The lime-ore melt from two AC open-arc furnaces is contacted with SiMn to produce 50 000 tons of medium carbon FeMn per annum. Metallics in the slag are reclaimed in a jigging plant, which has been in operation since 1999. The flow of materials between the jigging plant and furnaces has been optimised. The amount of recycle slag in the feed of the SiMn furnaces has been decreased by more than 30% which still provides satisfactory stability of the furnace operation. The jigging plant has absorbed all the additional slag generated, to recover SiMn metal. A review of the raw materials used and operating parameters for SiMn production was also undertaken. Slag to metal ratios were decreased by more than 30% by reducing the slag recycle, removing magnesite from the recipe and introducing high-grade ore. Electrode penetration was improved by reducing coke levels and by utilising more reactive coal. The pitch circle diameter (PCD) was reduced to get a better operating stability on furnace no 5 using the MINSTRAL Control System. Energy consumption on the furnaces improved by more than 15% while SiMn production increased as a result by more than 18%.

Jan 1, 2004

By Roozbeh Afzali

Designing an appropriate tunnel blasting pattern reduces the cost of rock breakage and subsequent operations such as loading, haulage and support of tunnels. For that reason, we developed a software that designs tunnel blasting patterns. Using this software, three different tunnel blast design models based on parallel hole cut, namely, Swedish, Konya and Energy Balance, were investigated and compared for a virtual tunnel. Accordingly, blasting patterns were designed, for different cross sections. The trend of parameters such as specific charge and specific drilling as functions of tunnel cross-section was determined for each model. Our results show that, in general, The Swedish model gives lower specific charge and specific drilling compared to other models.

Jan 1, 2008

By V. Eloy Román

El presente trabajo evalúa la adición del oxígeno puro al circuito de cianuración, con la finalidad de incrementar el porcentaje de recuperación de oro y plata, así como su efecto sobre el consumo de cianuro de sodio. En ese sentido, la mayoría de las plantas mantienen un alto nivel de concentración de cianuro, en lugar de un alto nivel de oxígeno disuelto en la solución. Como consecuencia de ello , operan a niveles de cianuro de modo que la disolución del oro depende del nivel de oxigeno disuelto. Por ello, es más fácil mantener un nivel alto de cianuro, que un nivel alto de oxígeno disuelto en la solución, principalmente si se utiliza aire en lugar de oxígeno.

Sep 12, 2005

By Paul Hughes

This paper summarizes current underhand paste backfill mining as applied to Goldcorp Inc?s Red Lake Mine, Newcrest Mining Ltd?s Kencana Mine and the Lanfranchi Nickel Mine as well as ongoing research at the University of British Columbia?s Norman B. Keevil Institute of Mining Engineering. The Red Lake Mine utilises a 6 m wide undercut with a 2 MPa unconfined strength paste in order to selectively mine its high grade, high-stress orebody. Kencana?s orebody is located in a poor rock mass environment. An 8 m wide, 2 MPa unconfined strength paste sill allows a safe working condition for its high grade orebody. The Lanfranchi Nickel Mine utilises a cable-supported, 2 MPa paste, with 12 m span sills, to optimize the mining of the squeezing rock mass. This paper details the rock mechanic hazards, ground support techniques, paste practices and unique conditions for each mine. Further, an update of ongoing research at the University of British Columbia, focussing on the optimization of safe mining in underhand cut-and-fill mining in high-stress/weak rock masses, is presented.

May 1, 2011

The Mine Safety and Health Administration (MSHA) conducted a respirable dust survey to evaluate the effectiveness of a water curtain utilized for dust control on continuous miner sections. The purpose of this survey was to determine if the water curtain was effective in reducing respirable dust concentrations, since several mines currently use water curtains to control miners? respirable dust exposures. The survey was conducted on a supersection of an underground coal mine, which utilized two continuous miners on the same split of air. Each continuous miner alternated taking a cut so that both continuous miners would not operate at the same time. The underground coal mine is located in Knox County, Indiana. The water curtain evaluated in this survey was located in the last open crosscut between the intake side continuous miner and the return side continuous miner. When the intake side continuous miner cuts coal, its exhaust air would be used to ventilate the return side of the section. The intent of the water curtain was to reduce the intake air respirable dust concentration (generated by the intake side continuous miner) before the air stream ventilated the return side of the section. To determine the effectiveness of the water curtain in reducing respirable dust concentrations, respirable dust sampling pumps were placed on both the intake side and the return side of the water curtain. Additional respirable dust sampling pumps were placed farther downstream from the water curtain to monitor dust levels downstream of the water curtain, but in an area where respirable dust would not be created by anything other than the intake side continuous miner or additional section air. The water curtain and the respirable dust sampling pumps were operated only when the intake side continuous miner was cutting coal. The samples were analyzed for respirable dust and quartz content. The water curtain showed minimal effect in controlling respirable dust and respirable quartz dust, but the reduction was so negligible that this survey could not quantify the reduction. The measured reductions are within the accuracy of the sampling equipment.

Jan 1, 2009

New Zealand has often been quoted by metallurgists and others as one of the countries in which Tellurium is found, and locally it has been recorded that appreciable quantities of tellurium have been met with in the Thames and surroundingdistricts. However, specimens containing tellurium which have been obtained on this field have not been preserved and their scarcity today points to the fact that tellurium is not here abundant.To ascertain its distribution, analyses and assays have been made by the author on a large number of ores, the results of several of which are given below.The presence of any considerable percentage of tellurium has an important bearing on the metallurgical treatment of ores in which it is found.

Jan 1, 1901

By H. Arima, T. Fujita, W. Yen

The copper catalyzed gold oxidation and reduction mechanisms in ammonium thiosulfate solution were investigated by Eh-pH diagram based on the optimum reagent combination for 60 mass% -75 µm silicate ore at 16g/t Au with the maximum gold extraction of 92% and the minimum ammonium thiosulfate consumption of 23 kg/t-ore for 24 hour’s leaching at ambient temperature. The gold recovery by cementation was nearly 100% by Zn and Al powders at Metal/Au mass ratio of 30, and around 95% by Cu powder at Cu/Au+ mass ratio of 50. In order to oxidize the gold efficiently with the less thiosulfate consumption, the stable region of [Cu(NH3)4]2+ should be as wide as possible in the region, where [Cu(S2O3)2]3- was more stable than [Cu(NH3)2]+. In order to reduce gold from the pregnant solution with the less metal powder’s (Zn, Cu, Al) consumption, the stable region of [Cu(S2O3)2]3- should be wider than [Cu(NH3)2]+ on copper precipitation. Zinc powder may recover gold more efficiently than copper powder with the similar trend on the effect of ammonia, copper and thiosulfate. However, the large amount of copper will be co-precipitated along with gold since the stability of zinc ammine and thiosulfate complexes are higher than that of copper’s. Aluminium may reduce gold efficiently at higher thiosulfate concentration and pH. These results were confirmed and compared with the optimum reagent combination for finer grind sample at 100 mass% -75 µm, which is the optimum ore size for the standard cyanidation at 1.0 g/ l NaCN to obtain about 95% gold extraction. The optimum reagent combination was concluded as 0.5 mol/l NH4OH, 0.0001 mol/l CuSO4*5H2O and 0.05 mol/l (NH4)2S2O3 with the result of 94% gold extraction and 3kg/t-ore of ammonium thiosulfate consumption. Gold and copper stabilities were well agreed with the result of coarser grind ore thermodynamically. The lower reagent combination will reduce gold oxidation power, but significantly minimize the reagent consumption. From this pregnant solution, nearly 100% of gold was successfully recovered by zinc precipitation at Zn/Au+ mass ratio of 30. Aluminium and copper precipitations resulted in less than 40% of gold recovery at Metal/Gold mass ratio of 30. The reagent consumption cost on this lower reagent combination followed by zinc precipitation was $1.6/t-ore, while the cyanidation was $3.1/t-ore. Thiosulfate oxidation mechanism indicated the similarity to Belousov-Zhabotinsky reaction.

Jan 1, 2002

By A F. Cooper

Otago Schist in the Mount Patriarch, High Burn and Cameron Creek areas of northwest Otago grades from textural grade IIA in the east to textural grade III in the west. The entire region is of the actinolite-pumpellyite metamorphic facies. Lithologies in the area are interbedded turbidite sequences comprising pelite and psammite together with pebble conglomerate, greenschist and metachert horizons. The mineral assemblage of the schist is typically quartz-albite-epidote-actinolite-pumpellyite-chlorite-stilpnomelane-calcite. A good foliation is well defined in the area and is predominantly parallel to bedding, except in hinges of mesoscopic isoclinal folds. The structure of the area appears to be defined by a large southwest plunging isoclinal fold defined by bedding with a steeply dipping axial planar foliation. Kink folding and dextral strike-slip faulting in the area postdates the ductile phase of deformation. Pods of rhodonite, rhodochrosite, spessartine garnet, coombsite, caryopilite, Mnstilpnomelane and Ni-Cu-Zn sulphides were found in concordant metachert layers in the Mount Patriarch area. Metachert was also found in float in the Cameron Creek area. Malachite occurrences relating to copper mineralisation were also noted in a green metachert horizon on the eastern flank of Mount Patriarch. The coombsite, in only the third observation worldwide, is the most Fe-rich variety reported.

Jan 1, 2003

By G. P. Tomaino

Talc is a layered, hydrous magnesium silicate mineral. It has a soft, soapy feel and typically a smooth texture. Talc is also known for its insulation, heat resistance, chemical stability, oil absorption and strong covering quality. Talc, Mg3Si4O10 (OH)2, has a theoretical chemical composition of MgO at 31.7 percent, SiO2 at 63.5 percent, and H2O at 4.8 percent. However, talc’s chemical and mineralogical composition can vary depending on its geological history/parent rock association. These mineral associations and variable levels are usually chlorite and carbonates (magnesite, calcite and dolomite). Two key elemental substitutions that can occur in the talc crystal structure are iron for magnesium and fluorine for hydroxyl. These compositional differences may limit or enhance the talc’s usage in specific market niches. The United States remains self-sufficient in most grades of talc.

Jan 1, 2005

By T. Bajpayee, J. Ellenberger

Microseismic monitoring and evaluation is one aspect of the National Institute for Occupational Safety and Health (NIOSH) research program. Roof falls are often preceded by a period of elevated microseismic activity, but not all periods of elevated activity result in a roof fall, nor do all roof falls occur after some amount of elevated activity. The objective of this study is to review periods of elevated microseismic activity and determine whether fracture activity rate can be used to anticipate the initiation of roof falls. The study was carried out at an underground limestone mine where major roof falls are associated with excessive horizontal stress. The progression of roof falls was detected by the microseismic signature produced by the rock falling from the mine roof onto the mine floor, which is termed a roof fall impact event. A total of nine elevated fracture activity periods that resulted in seven major roof falls were examined. It was observed that elevated fracture activity preceded the initial roof fall impact event in three out of four major roof falls. The initial impact event was not identified for the remaining three roof falls. Fracture event rates were analyzed and a roof fall alarm trigger of five fracture events in a ten minute time period was established for this test case. The fall alarm trigger was tested against six of the elevated activity periods. Four roof falls occurred in the six periods of elevated activity, and two would have triggered the alarm before the roof fall occurred, while two false alarms were generated. The results show that limited success would have been achieved by the microseismic system as a roof fall alarm trigger. However, the trigger would have been successful at warning of the onset of elevated activity, allowing mine employees to respond appropriately. The study highlighted some issues with implementing such a system in an operating mine, including the need for real time identification of fracture related microseismic signals among mining induced signals, and accurate location and identification of fracture clustering.

Jan 1, 2007

By A. Roca, G. Ríos, I. Ruíz, M. Cruells

Flash Smelting Furnace (FSF) hot dust-laden is cooled in a waste heat boiler (WHB) and then dedusted in electrostatic precipitators (ESP’s) before being treated, together with the Peirce Smith Converters off-gases, in the sulfuric acid plants for SO2 removal. FSF dust is sulfated by SO2 and O2 in the WHB. Typically, 70% of the dust from the FSF drops in the WHB while the remainder is caught in the ESPs. The collected dust is recycled to the FSF for Cu recovery. Some smelters have developed hydrometallurgical treatments to recover Cu from the dust; impurities, such as As and Bi, are bled as leach plant residues. This paper presents a study (laboratory scale), of leaching the FSF dust, generated in Atlantic Copper Smelter using the weak acid bleed from the gas scrubbing/cooling section (GSCS) of sulfuric acid plants. Leaching was performed with 0.5 mol L-1 sulfuric acid concentration, 60ºC, and a solid/liquid ratio 1/3. After leaching, H2O2 was used for arsenic and iron oxidation. pH was adjusted for precipitation of arsenic and iron as scorodite or as scorodite and arsenical jarosite. The precipitation was carried out at 95ºC during 3-6 h. Liquids after precipitation are suitable for subsequent treatments of electrolysis. INTRODUCTION The copper smelter dusts are usually recirculated totally or partially to the flash furnace. This practice increases the amount of impurities feeding the furnace. Some authors have developed processes for treatment of these materials for copper and zinc recovery and for arsenic, antimony and bismuth inertization. The processes for the treatment of copper smelter dusts can be pyrometallurgical (Yu, 1987; Carter, Vance, Aldridge, Zaw, & Khoe, 1994; Fu, Jiang &Wang, 2000), hydrometallurgical, or mixed processes (Yin et al, 1992; Mulale, Mwema, & Mashala, 1999; Gorai, Jana, & Khan, 2002). Hydrometallurgical processes have been extensively studied and, in some cases, applied to an industrial scale. The most important chemical reagent proposed for leaching the dusts has been sulfuric acid (Roman-Moguel, Plascencia, Pérez, & Garcia, 1995; Gabb, & Evans, 1997; Larouche, 2001; Morales, Cruells, Roca, & Bergó, 2010; Cáceres, Cruells, Morales, & Roca, 2012; Ecometales, 2013; Yang, Fu, Liu, Chen, & Zhang, 2017). Processes developed in alkaline media, and in some cases with the presence of sulfide, have also been carried out (Gabler, & Jones, 1988; Morales, Hevia, & Cifuentes, 2009; Alguacil, Garcia-Diaz, Lopez, Rodriguez, & Alonso, 2013), as well as by using a bioleaching process (Massinaie, Oliazadeh, & Seyed Bagheri, 2006; Bakhtiari, Atashi, Zivdar, Seyedbagheri, & Fazaelipoor, 2011).

Jan 1, 2019

By F. T. Cawood

One of the consequences of globalizing mine finance is a necessity to apply uniform accountancy and valuation standards that are clearly understood and consistently applied by the global investment community. However, each country has unique circumstances, which sometimes make it difficult to align domestic practice with international requirements. South Africa is no exception and issues such as its political history, a taxation regime enforcing different rules on different mineral producers and a unique mineral rights ownership distribution, are barriers to internationalization. The economy is in a transitional phase as a result of the many and diverse policy documents following the change in political dispensation in 1994. Many of these documents have recently been implemented through new legislation and, in the case of mining, negotiations are continuing in order to ensure an acceptable outcome. This paper discusses the challenges that the South African minerals industry faces in the field of mineral property valuation. It draws on international experience and includes a discussion on the unique considerations that the South African mineral property market must take into account in establishing a code for this purpose, as such a code could later be aligned with international practice.

Jan 1, 2004

Throughout history, many of the world's achievements, conflicts and problems can be traced to the demand for minerals. With the rapid expansion of our industrialised society in recent years the demand for minerals has grown to such an extent that uncertainties about availability and cost have arisen, especially in the case of energy minerals.Minerals have acquired a new dimension for governments as the availability of these resources is interwoven with the ability of governments to achieve their developmental goals on national and international levels. Accordingly, the supply of minerals will increasingly be affected by social and political factors.

Jan 1, 1986

By M. Mononen, J. Huuskonen, M. Vauhkonen, J. Kourunen, A. Lehikoinen

"A new approach to measure process conditions in flotation cells is presented. Real scale flotation cells in a Zinc circuit are imaged using Outotec LevelSense sensors based on electrical resistance tomography. The latest results from long period plant tests show that the sensors together with FrothControl analysis give new information that correlates well with other process parameters. The sensors can compensate for electrical contact contamination using an automatic calibration technique and they are basically maintenance free. The results indicate that using the LevelSense sensors and FrothControl solution, the process control and optimization can be done automatically, stabilizing and improving the metallurgical performance of the flotation process.INTRODUCTIONThe froth flotation process is widely used in mineral industry for the separation of minerals from low-grade ore slurry. Different property parameters of froth and slurry could be measured to monitor and control the flotation process: air bubble size distribution, flow dynamics, thickness of the froth bed, amount of solids in the froth, etc. Some techniques already exist that can be utilized in studying these important parameters on-line. Examples of the techniques are the high-speed video imaging, simple conductivity probes, ultrasound techniques, floats and pressure transducers (Maldonado et al., 2008). These techniques, however, often suffer from some limitations. For example, the video imaging only gives information from the surface of the froth, simple conductivity probes suffer from contamination and the floats may get stuck and therefore do not give reliable signal for process control and optimization."

Jan 1, 2013

Engineering education has become a matter of national concern, at last, so I would like to talk about the links between the mining industry, the universities and technological developments. The Australasian mining industry and the mining schools have collaborated closely since the first school was established in 1871 and during those years there were a series of remarkable technological developments. For example:In the late 1880s George AndersoIl Richard developed chloride leaching of gold at Mt Morgan. This made a large difference to the wealth of Mt Morgan Mining Ltd.In the mid 1890s Robert Sticht demonstrated that pyrite smelting was an economically feasible process at Mt Lyell and the wealth which came to Mt Lyell Mining Co from his outstanding work made it one of the great companies in the country.During the first 15 years of this century flotation was developed at Broken Hill and it has proved to be one of the great technological inventions of this century.In the 1920s G K Williams started his outstanding work on lead smelting and refining at Port Pirie, this was work which ultimately re-wrote the text book on lead metallurgy and established Port Pirie as the mecca for lead metallurgists.In the 1920s also Frank Stillwell, later joined by Austin Edwards, established the new science of mineragraphy at the University of Melbourne. They were both great geologists, both were superb scientists and oddly enough both were outstanding athletes.In the 1930s Dr Ian Wark, a man in the front rank of Australian scientists of any period, started his outstanding work on flotation, work which resulted in a text book which remains a leader in its field today.In the 1930s also Arnold Black at Broken Hill South Ltd picked up the work which had been done at Mt Lyell many years previously and eventually wrote the papers on hydraulic fill which demonstrated that he led the world in fill technology. What a remarkable story of achievement it was, it laid the groundwork for the great industry we have today. It was possible because the industry was well supported by outstanding university schools and I would like to talk about some of these.

Jan 1, 1989