Search Documents

A model has been developed for drum scrubbing which allows selection of geometry and power input. Specific aspects considered are: Calculation of total static and operating volumes. Total residence time based on total operating volume. Solids residence time based on solids operating volume. Selection of the aspect ratio. Alteration of operating fill to allow for smaller or larger feed openings. Selection of proportion of critical speed. Calculation of shell and motor power requirements. The model uses either solids or total residence time to calculate the required operating volume. The solids residence time is based on the proportion of coarse solids in the feed. Material finer than the reject size is considered as part of the slurry. The solids operating volume is the static volume plus the surcharge on the discharge weir required for flow of the solids from the unit. The total operating volume is the static volume plus the surcharge on the discharge weir for the total flow to exit the scrubber. The burden density is calculated from the coarse solids bulk density and the slurry density that includes all the fine solids. Power is calculated using the Liddell and Moys correlations for burden position and shape, and the operating rotational speed. Results from the model (especially power) have been verified from industrial installations of significant size. Predicted and observed power draws are within two per cent. A check against the JKMRC mill model shows power draw prediction agreement to within four per cent.

Jan 1, 2004

By J. A. Beukes, M. Marais

TICOR South Africa is a new titanium feed stock producer. In the Ticor South Africa plant the ilmenite feed to the smelter plant is roasted to enhance its magnetic properties. This allows for the magnetic separation of chromite from the ilmenite. The magnetization reaction relies on partial oxidation with both under- and over-oxidation causing insufficient magnetization. To subject the roaster plant feed material to the required physical conditions a circulating fluid bed (CFB) roaster is used. This paper describes the development of a laboratory model that will aid in the control of the CFB roaster.

Jan 1, 2003

By B. P. Spigarelli

To meet the growing need for CO2 capture and storage technology, Michigan Technological University is researching CO2 capture and storage using carbonate solutions. The objective of the present study was to increase the absorption rate of CO2 into the carbonate solution without reducing the absorption capacity of the solution. This approach used a polypropylene glycol methyl ether (PPGME) as a surfactant to chemically alter the gas bubble size. Experiments were conducted to study the absorption rate of CO2 at varying surfactant concentrations of 0, 0.12, 0.24, 0.36, and 0.48 g/L. Results showed that as the concentration of surfactant increased in solution, the absorption rate also increased. The CO2 absorption rate increased from 3.45 mmol/min CO2 at 0g/L PPGME to 3.92 mmol/min CO2 at 0.48 g/L PPGME. This amounted to a 14% increase in the CO2 absorption rate with no decrease in absorption capacity of the solution.

Feb 27, 2013

Six pioneers of the American mining industry will be inducted into the National Mining Hall of Fame on Saturday, Sept. 13, at the Museum Convention Center in Leadville, CO. The 16th annual Mining Hall of Fame induction banquet will begin with a reception and open house at 5:30p.m., followed by the dinner and program at 7 p.m. The six inductees include James M. Gerstley, the only living member, and George O. Argall, Jr.; John F. “Leadville Johnny” Campion; Charles R. Nailler; Edwin N. Pennebaker and Russell L. Wood.

Jan 1, 2003

By W. J. Young, K. B. Macneill, C. N. Smith

"A BRIEF HISTORY OF THE MURRAY BROOK MINERAL DEPOSITDuring the mid-1950's intensive exploration activity in northern New Brunswick followed the discovery of the world class Brunswick base metal deposit. Using the prototypes of modern airborne geophysical and geochemical exploration techniques many mineralized areas in the Bathurst-Newcastle area were quickly identified. This base metal - silver camp is situated within the metavolcanic - metasidementary rocks of the Tetagouche Group which forms a roughly circular caldera-chaped voloanio complex of Ordivician age.One of the early results in the exploration history in the camp was the discovery of the Murray Brook Deposit by Kennco Explorations, (Canada) Limited. During routine ground checking of geophysical anomalies, most of which turned out to be graphitic schist, the discovery of some copper bearing float was made by the exploration team. This encouraged the company sufficiently to carry out a regional stream sampling program which lead to a large anomaly associated with a hematitic gossan. Diamond drilling of a weak Slingram anomaly over the gossan zone resulted in the discovery of massive sulphide lenses. This was followed in 1956-7 with an intensive drilling program. The result was the delineation of a potential ore body containing an estimated 23 million tons with an overall grade of 0.44% copper, 0.86% lead, 1.95% zinc, 25.73 g/tonne (0.91 oz/ton) silver, 0.28 g/tonne (0.01 oz/ton) gold. Within this package were higher grade zones of copper and lead-zinc mineralization approaching ore grades.A thick blanket of gossan was present and is reported to have caused the drillers considerable trouble as they attempted to penetrate it to get to the underlying sulphides. The gossan, consisting of iron oxides and silica fragments sits on top of the massive sulphides and attains a remarkable thickness of 45.5 meters (150'). Early work had suggested that the gossan was enriched in gold and silver. If this were the case and if the precious metal could be leached out with cyanide, then mining and recovering those values might be economic.With this in mind Northumberland Mines Limited optioned the property from Kennco in 1985. Preliminary leach tests indicated that indeed the gold in particular leached readily. Subsequent drilling of the gossan (using triple core barrel technology for better recovery of the easily ground core) indicated 1,536,363 tonnes (1,690,000 tons) with an average grade of 1.05 g/tonne (0.037 oz/ton) gold and 42.13 g/tonne"

Jan 1, 1993

By Thomas M. Barczak, David P. Conover

Longwall shields provide essential ground control in longwall mining, yet a high percentage of shields are operating at less than peak capacity and many at well below the rated support capacity due to defective hydraulic cylinders or malfunctions in other hydraulic components. Leg pressure data are currently collected on state-of-the-art longwall shields, but typically are not analyzed to evaluate shield performance. The National Institute for Occupational Safety and Health (NIOSH) Shield Hydraulics Inspection and Evaluation of Leg Data (SHIELD) program is a Visual Basic software system that is designed to analyze leg pressure data and identify shields that are not performing to rated specifications. The program analysis is configured to detect the following conditions: (1) loss of leg pressure, (2) imbalance in leg pressure, (3) low set pressure, (4) low yield pressure, and (5) full extension of the bottom stage. Other performance assessment measures include the percentage of the support capacity utilized (ratio of peak load to yield load), the percent of time that a shield operates at yield load, the ratio of the set load to the yield load, and the amount of support capacity that is lost due to leaking cylinders. Historical record keeping will allow the user to select a particular shield and review the performance record as developed by the program for that shield. In addition to these performance assessment measures, the software will include an animated description of shield hydraulic systems that will describe the operation and significance of each hydraulic component and the impact of component failures on the shield’s capability to provide the required roof support. A general overview of the SHIELD program is provided in the paper together with an example analysis of a 2.5-year-old Australian longwall face.

By Dolly Chakraborty, S. Ranganathan, S. N. Sinha

Experiments were conducted to study the influence of temperature, particle size and ore/coke ratio on the kinetics of reduction. The rate of reduction increased with temperature. The reduction of iron was completed at shorter time intervals at temperature above 1000ºC. Usually the reduction of chromium commenced after the reduction of iron was almost complete. Reduction was controlled by diffusion at low temperatures and by chemical reaction at higher temperatures. The nature of the reducing agent had a very significant influence on the rate of reduction. The study showed that chromium was converted into the carbide during reduction. Increasing the size of the reducing agent increased the rate of reduction initially. After a critical size, the rate of reduction decreased. However, increasing the size of the ore particle decreased the rate of reduction, initially. Beyond a critical size, it increased. An optimum particle size of the chromite ore and that of coke must be chosen, particularly in the production of agglomerates to achieve maximum degree of reduction.

Jan 1, 2007

Flawed mining studies have been major contributors to poor investment decisions in mining for many years, contributing to the long period of poor industry profitability. Most of the major mining houses have now adopted quite formal processes and quality standards for mining studies to reduce the potential for poor investment decisions in the future. Other organisations such as the World Bank also have specific requirements for particular types of studies, such as bankable studies. This increasing requirement for rigour and discipline means a highly structured and phased sequence of studies is now required along with the development and adoption of industry-wide standards in mine ventilation studies. New terms in the study process such as ?independent peer review? and ?hold and review? are assisting in this process. More traditional terms such as ?feasibility study? and ?pre-feasibility study? now have much more precise technical definitions. Specific standards for the ventilation components of the various phases of a mining study are proposed in this paper.

Jan 1, 2009

By M. Prud’Homme

Potash is an important natural mineral used largely as a fertilizer in the production of food and fiber. About 93 percent of all potash consumed globally is used in agriculture as fertilizer. The balance is used to manufacture potassium chemicals. Most potash is extracted by conventional underground mining methods. Solution mining is used when underground deposits are irregular and very deep. The other main production method involves the evaporation of brines in shallow salt lakes, followed by the harvesting of potassium minerals.

Jan 1, 2005

By Jack Elorenta

We often hear that, "Blasting was an art, but now blasting is now a science". 'Scientific' blasting implies that we have quantified and reproducible measurements of the feedstock and product of the blasting process. However, the industry's reluctance to adopt two key technologies, drill monitoring and optical size analyzers, sheds doubt on the claims of scientific blasting.

Jan 1, 2003

By Christopher C. Jobes, Alan G. Mayton, Timothy J. Matty, Joseph P. DuCarme

Mining injury statistics show that a significant number of back, neck, and head injuries are linked to exposure from vehicle vibration. Use of a suspension seat is a common way to isolate the vehicle operator from the adverse effects of vibration exposure. Thus, researchers at the National Institute for Occupational Safety and Health1 – Pittsburgh Research Laboratory (NIOSH – PRL) performed laboratory studies on four passive and two semi-active seat suspension designs. These are typical of seat suspensions commonly found on large off-road heavy surface mining, construction and agricultural vehicles as either replacement or original equipment manufacturer (OEM) systems. One included a pneumatic (air bladder) spring mechanism. The fifth and sixth suspensions were a NIOSH magnetorheological (MR) semi-active damper design based on the pneumatic (air bladder) and one of the coil spring suspensions above. These suspensions were modified with a commercially available MR damper substituted for the OEM damper. These six seat suspension systems were tested and analyzed, for vertical vibration only, using the ISO 5007 Standard [1]. This paper describes the laboratory vibration tests using a MTS® shaker table and discusses the results obtained for the different suspension designs and highlights the rheonetic technology studied. Implications of the seat suspension designs relative to their capabilities for isolating vehicle operators from vibration exposure are discussed. Results for suspensions 1 through 3 showed frequencies of isolation from 2.1 to 3.0 Hz using the 40-kg (88-lb) mass and from 1.65 Hz to 1.8 Hz using the 80-kg (176-lb) mass. Suspension #4, in tests with only the 80-kg (176-lb) mass, showed an isolation frequency of 3.7 Hz. With the MR damper added to seat suspension #4, the peak transmissibility was lowered from 1.3 to 0.95 and showed a corresponding downward shift in frequency from 2.25 Hz to 1.4 Hz. In fact, the results for suspension #5 (the MR damper added to seat suspension #4), using test #3 conditions of the programmed control algorithm, showed isolation (attenuation of transmitted vibration) throughout the test frequency range from 1.0 to 6.0 Hz.

By C. A. Cole

This work consists of research in cable fault location and the construction of four field-test units based on the research. Swept-frequency sounding of mine cables with RF signals has been the technique most thoroughly investigated. The swept-frequency technique is supplemented with a form of moving target indication (MTI) to provide a method for locating the position of a technician along a cable and relative to a suspected fault. Separate, more limited investigations involved high-voltage time domain reflectometry and acoustical probing of mine cables. Particular areas of research included microprocessor-based control of the swept-frequency system, a microprocessor-based fast Fourier trans-form for spectral analysis, RF synthesizers, transmit-receive switches, RF receivers, cable dispersion-compensation techniques, low-voltage multielement display systems, and techniques for injecting or recovering RF energy through cable walls in support of clamp-on fault locators.

Jan 1, 1982

By M. Arias

"An attractive foreign investment legislation, an anti-mining framework in the jurisdiction where a head office is located, the geographical location of the mineral resources, a country that offers the technology needed by the industry for its operations -- these are some of the many factors that make mining and mineral exploration a global business. It is precisely in the complexity of this new era of globalization and market environment, that sustainability initiatives are challenged. Responsible management of mineral exploration and mining is no longer defined by the use of efficient technology and resource management. Sustainability is not only a report compliance exercise or a green revolution. Sustainability is like any business, a long term profitable proposition. This new approach encompasses four pillars: social, economic, environment, and culture. This new approach connects humans and corporations; it is the way to engage, respect and improve relations with the people with whom we work and our neighbours."

Jan 1, 2011

By P Maillet, A J. Crawford, S M. Eggins

TheFiji Islands are remnants of a once continuous Solomon-Vanuatu-Fiji-Tonga volcanic arc (the Vitiaz arc), located at the boundary between the Indian-Australian and Pacific plates. They record a history of: (i)                  arc volcanism the late Eocene to late Miocene, (ii)                an extensive magmatic response to arc rifting (5.5 - 3.0 Ma) during which volcanism was dominated by shoshonitic to tholeiitic basalts, and as rifting continued, (iii)               a transition from arc to intraplate volcanism.   The Hunter Ridge-Hunter Fracture Zone separates the inactive South Fiji Basin from the actively spreading North Fiji Basin, and has been considered to be a transform zone, almost parallel to the motion vector of the Australian plate. However rocks dredged during the 1993 æAlizeÆ cruise, from along the northern part of the Hunter Ridge are typical arc tholeiites, and therefore demand that subduction has occurred beneath the Hunter Ridge sometime during the last ~5 Ma. The Kadavu Island group, south westernmost Fiji, lies at the north-eastern end of the Hunter Ridge-Hunter Fracture Zone, and possibly results from oblique subduction of South Fiji Basin oceanic crust, which may have accompanied the anticlockwise rotation of Fiji during opening of the North Fiji Basin. These islands consist dominantly of 3.4 - 0.5 Ma old medium-high K andesites and dacites, with many traits typical of subduction-related volcanics, ie predominance of intermediate members (55 - 65% SiO2) no Fe enrichment, TiO2<1%, and negative Nb-Ta anomalies. These features contrast strongly with volcanics from elsewhere in Fiji around this time, where volcanic centres produced Om-like intraplate olivine basalts. The Kadavu Islands become gradually younger to the southwest, and show a significant decrease in K2O with time. The north easternmost islands (Astrolabe islands) containing the oldest rocks (~3 Ma) have shoshonitic affinities and are considered to be of similar age and composition to the youngest shoshonites found elsewhere in Fiji.

Jan 1, 1995

By S. H. Miller

Biodegradable hydraulic fluids can save tens or hundreds of thousands of dollars in fines and clean up costs in the event of a hydraulic fluid leak or spill. When properly selected, applied, maintained and monitored, a biodegradable fluid will have a long useful life and will protect equipment as well as or better than conventional petroleum based hydraulic fluids.

Jan 1, 2000

By Bruce Vandenberg, Andy Bartfay-Szabo, Steve Conway

Recent advances in solid-state, field portable, fast framing video camera systems and PC based frame capture hardware now allow blast imaging up to 500 frames per second. Up to 8 seconds of data can be stored directly into the unit, downloaded to a PC or archived to a standard VCR without data compression. Since no film processing is involved, motion analysis can be performed instantly and on-site within a few minutes. This paper will describe the design features and applications of the SVClOOO system and compare these with the analogous aspects of film based cameras.

Jan 1, 1995

Spectrum Resources commenced operations as a public listed mining company in August, 1983, with a variety of precious metal projects in New Zealand. At that time the outlook for most mineral commodities, with the notable exception of precious metals, was decidedly gloomy. Metal prices were depressed and demand forecasts were universally gloomy. Against this background the company reviewed the non-traditional metals sector to try and identify a 'new' metal with an above average demand growth and market value. Lithium, a commodity with exciting new applications in storage batteries and alloys, met both criteria. Annual world consumption of lithium is around 7000 tonnes; current prices are around $NZ40/lb for lithium metal and demand growth is projected at five to seven per cent per annum. Geothermal fluids at Wairakei and elsewhere contain anomalous amounts of lithium and in May, 1984, the Chemistry Division of DSIR was commissioned to carry out a literature survey on the possible recovery of lithium and other minerals from geothermal waters. The survey results were encouraging and the company subsequently negotiated exclusive access rights, for research purposes, to geothermal discharge fluids from the Wairakei and Kawerau geothermal fluids. Most of the subsequent investigations reported here were carried out by Chemistry Division, DSIR, under contract to the company with some assistance from the Industrial Processing Division, DSIR.

Jan 1, 1986

By C. J. Kirkland

For two thousand years and more, we insular Britons have been grateful for the existence of the narrow strip of water that separates us from mainland Europe. It has given us a sense of security against invaders, though it has been breached many times. The first recorded serious consideration of a fixed crossing of the English Channel was in around 1802, when it was suggested to Napoleon I. The motive was not entirely peaceable and the British Navy, who saw themselves as defenders of our shores, were decidedly unenthusiastic A whole series of imaginative schemes were proposed in the course of the nineteenth century, embracing viaducts, immersed tubes, artificial islands as resting places for the horses which were to draw carriages, as well as mechanically bored tunnels. The first Channel Tunnel Company was formed in 1872, and an application for permission to construct a tunnel was made to the British parliament. A Colonel Beaumont, of the Corps of Royal Engineers designed and constructed a machine which, in around 1882, bored over a mile of tunnel out to sea from Britain which exists to this day.

Jan 1, 1991

In understanding the consequence of existing law, and the likely implications of its reform, it is necessary to comprehend the logic of the situation that the law provides individual decision makers and how that situation would be adjusted by reform. In particular, the way in which natural resources, including minerals, are used and managed is influenced by the definition and structure of property rights that the law provides. Property rights are enforceable claims to use or to benefit from resources. An example is a mining licence that allows its holder to extract minerals in a specified area. Property rights establish the structure of incentives, opportunities and constraints within which resource use decisions are made, ie the logic of the situation, and hence influence the use and management of resources. The extent and type of mining in New Zealand, for example, reflects the rights that miners have to extract minerals, and their rights to benefit from mining as against their duties to compensate landowners and pay royalties. This paper describes the characteristics of minerals that are relevant to the definition of property rights, analyses the implications of alternative property right arrangements and describes the existing situation.

Jan 1, 1988

By Paul Russell, M. M. Kimberley, Erick F. Welland, Louis Cope, C. C. Mosher, William M. Shepard, William C. Larson, Graham Closs

Exploration activities in 1980 felt the effects of unstable economic conditions and oscillating metal prices. In the cyclical, boom-or-bust precious metals and uranium markets, precious metals activity flourished and uranium was definitely in a slump. By November last year, the price for vellowcake was down nearly $20 from two years earlier. Many mining and milling operations closed, particularly in Wyoming, New Mexico, and Colorado. Decreasing emphasis on nuclear power continued to impact the market, as did the Three Mile Island accident of 1979. Earlier forecasts estimated that 10 to 12 reactors would be ordered per year by US utilities throughout the 1980s, but current forecasts suggest that it may be 1983 or 1984, or even later, before any new US plants are ordered, according to Thomas A. Boyden, vice president of Nuclear Exchange Corp. "Without those new plants, the consumption loss to industry is 4 to 5 million pounds (1.8-2.3 kt) of uranium per year. The cumulative loss to the industry is currently estimated at 25 to 30 million pounds (11.3-13.6 kt)," Boyden said in a May 1980 presenta¬tion. Despite the plunging market, there were a few notable uranium explora¬tion programs: •Exxon expanded uranium exploration in New Mexico, where the company reportedly took preliminary steps toward acquiring mineral rights to a 22-km2 prospect, 19 km south of Santa Fe. • Mountain States Resources began the second phase of an exploratory drilling program on its Sinbad/ Solo prospect in Utah. • Also in Utah, Cotter Corp. drilled its first exploratory hole in the Dirty Devil River district. Exploration for precious metals in 1980, however, appeared to tend toward the opposite extreme. High prices sparked near feverish searches in Alaska, California, Colorado, and Nevada. Numerous mines abandoned years ago were revived with some signs of success. Significant gold finds were reported in California and Nevada: • Homestake Mining Co. announced a gold discovery in California estimated to contain over 5 Mt with an average grade of about 5.8 g/t. Because the deposit consists of finely disseminated particles not visible to the eye, many speculate that prospectors bypassed the area during the 1849 California gold rush. • Newmont Mining Corp. discovered two gold ore bodies-Maggie Creek and Gold Quarry. Maggie Creek reportedly contains an estimated 13.7 t of gold in 4.3 Mt of ore, and Gold Quarry contains about 31.1 t of gold in 9 Mt of low grade ore and 2.3 Mt of higher grade ore. Highlights of this year's exploration review include articles on the modest growth recorded in geophysical activity, technical developments in exploration geochemistry, the variety of new instruments being tested or made available for exploration, and a state-by-state exploration review for the year.

Jan 5, 1981