Search Documents

By Zara Hosseini

?Microseismicity ?Seismic Systems ?Intrinsically Safe and Explosion Proof Seismic System ?Case studies: ?Gas Drainage Optimization ?Fault Identification ?Conclusion Seismic Event ?Occurrences in which energy is released in the rockmass creating a series of seismic waves propagating throughout the rockmass ?Can cause a Fall of Ground or CoalBurst Factors creating Seismicity: ?Mining at Depth ?High stress zones ?Major geological structures ?Mining practices and strategies ?Mining activities i.e. drilling and blasting

Aug 1, 2013

By Rudolph P. Frizzi

Structures supported on ACIP and DD piles perform successfully when quality control is maintained from the initial site subsurface investigation through pile design, bidding, and construction. The four stages of ACIP / DD pile construction are: preparation, augering the pile, grout / concrete placement, and reinforcement installation. During all four stages, careful observations and communication between the contractor and the owner's engineering inspection personnel are vital to successful pile completion. Automated monitoring equipment (AME) exists to supplement, but not replace, the field personnel's observations during the pile augering and grouting operations. Full-scale field load testing is done to verify the pile's geotechnical and structural design, and the contractor's pile installation means and methods, using several procedures including: conventional top loading, high-strain dynamic, rapid axial compression (i.e. Fundex PLT and Statnamic), and Osterberg Cell. Non-destructive sonic testing is performed to investigate the below-grade sectional properties of the completed pile; such methods include: low-strain impulse testing, and single-hole and cross-hole sonic logging. Post-construction observations are necessary to verify pile location and top properties prior to overlying cap construction.

Jan 1, 2005

By J. R. Yates, R. J. Young, G. E. Forward, J. B. Farrell, R. J. Milbourne

"Sustainable development in the mining and metallurgical industrial sectors can be implemented by two distinct groups: the managers and operators of existing facilities, working with industrial processes and systems that have been operating for many years, in some cases, several decades; and those who are engineering and building new facilities or upgrades of existing plants.The focus of this paper is to look at approaches and tools available to bring sustainable development thinking and action to these two distinct areas. The paper will discuss the concept of working with existing facilities and processes to minimize waste and maximize product from a regional raw material/resource consumption perspective using by-product synergy. The BPS concept has been carried out in Texas (e.g., TXI-Chaparral’s STAR), in Calgary, Alberta, with Suncor assistance, in Montreal, Quebec, with Noranda as project leader, and currently in Ontario with Dofasco as industry champion. Successful outcomes are presented. The paper will also discuss a new approach to designing greenfield facilities or upgrades to existing plants using a sustainable development review process. Undertaking the review early in every project can institutionalize the concept of discussing and implementing waste elimination, design for environment, ecoefficiency, risk minimization and community awareness and involvement in the future capital stock. The review process has been developed as an excellent tool for measuring and reporting on a corporation’s sustainable development progress. Examples of how this approach has been adopted in the mining and metallurgical industry, and the resultant outcomes are given."

Jan 1, 2003

By A. E. Koski

Two of the largest industries in northern Michigan, pulp and paper manufacturing and iron mining, formed a mutually beneficial partnership and collaborative research program to utilize paper mill residuals for waste rock stockpile reclamation. Historically, the majority of the paper industry’s residuals have been disposed of in landfills. The beneficial use of paper mill residuals for mine reclamation provides an environmentally sound recycling solution for the solids generated at northern Michigan paper mills and eliminates the need to strip additional overburden (glacial till) for final mine reclamation. Residuals offer a cost-effective source of organics and nutrients necessary for successful reclamation and waste rock stockpiles offer an economical and environmentally sound solution for disposal of residuals. The goal is to successfully pioneer technical development of paper mill residuals to accomplish vegetation of steep waste rock stockpile slopes and benches to establish a self-sustaining plant community that meets final reclamation requirements. Of the various types of iron mining wastes, rock stockpiles pose the greatest reclamation challenge. Success depends on incorporating sufficient organic matter into the rock stockpiles to produce a growth medium that can sustain vegetation without the need of overburden. This is an ongoing research program that is evolutionary in nature with numerous field trials, greenhouse studies, data collection and monitoring over multiple growing seasons. The program is a combination of innovative ideas and accepted reclamation practices that is proving to be a beneficial and economic approach to paper mill residual management and mine reclamation that will eventually lead from research to standardized reclamation procedures.

Jan 1, 2006

By K. Oraee

Proven and probable coal reserves in Iran are estimated to be in excess of 5 Billion tons while the annual coal production is a mere 2 Million tons. Underdevelopment of the industry has proved higher production levels to be impossible, despite growing demand for energy supplies. The existences of numerous legislation are thought to have a detrimental effect on coal mining activities to the extent that some business entities have become uneconomical in many areas. This paper provides an analysis of the prevailing mining laws, policy making, legal frameworks and obstacles. It also outlines some other obstacles enshrined in the law and also highlights areas where foreign direct investment should be encouraged. The costs of lost opportunities are then estimated. The paper concludes by demonstrating that deregulations, amendments and in some cases complete abolishment of the incumbent legislations governing the coal mining industry will greatly enhance development of the industry. The analysis provided in this paper together with the results obtained, can prove useful to macro-economic policy makers both at local and national levels.

Feb 27, 2013

By Andrew Wessman

Keywords: Recycling, Electrodeposition, Recovery, Dilute, Dissolved Metal Ions In order to facilitate the recovery of pure metals from solutions containing a mixture of dissolved metal ions, a pulsed electrodeposition method was developed. Using this method, it is possible to selectively remove metal ions from solution based upon the electrochemical potential of the particular ion desired. The use of pulsed electrodeposition rather than direct current electrodeposition creates an electrodeposited material with better morphology, increases electrical efficiency of the process, and avoids problems with short circuiting between electrodes. Using this method, it is possible to recover dissolved metal ions in a purified form in one simple step, and therefore maximizes recovery of the metal ions while obtaining them in a saleable form. This method is likely to be useful in improving the recycling process for numerous complex metal mixtures and alloys.

Jan 1, 2005

By Elaine T. Cullen, Thomas W. Camm

The mentor/learner model is a time-honored approach to teaching, including within the mining industry. Miners know when they see excellence and have a deep respect for experts in their field. By using expert miners as mentors to other, less-experienced miners, training programs can be developed that will have a legitimacy and credibility that resonates with those being trained. Building upon concepts in current theories of adult education, this paper highlights the unique advantages of using mentoring as a teaching method that can make the educational experience both interesting and effective. Current NIOSH safety training materials use these concepts to deliver effective adult learning experiences for workers in the mining industry.

Jan 1, 2002

By Daniel Journeaux

Introduction Daniel Journeaux is President of Janod Incorporated. Janod is a family owned and operated company that has been working in the field of slope stabilization since 1970. Daniel has worked in the rock stabilization industry for 25 years and has been President of Janod since 1992. Daniel has been an invited speaker for the Federal Highways Administration for the Northwest and Southwest divisions, Queens University in Kingston Ontario, The University of Laval, Vulcan Materials Company, CSX annual meeting for the Northeast Division. Daniel has written several articles and has been published in Pit and Quarry, World Tunneling, and American Shotcrete Association magazines. What is Required to Remediate Highwalls There are several techniques available to stabilize highwalls or temporary rock walls to allow for safe mining practices. The following are some of the techniques that can economically be used.

Jan 1, 2005

By Hideo Ando, Yuka Satou, Tatsuya Ishitake

Whole-body vibration occurs when the body is supported on a surface which is vibrating. Occupational exposures to whole-body vibration mainly occurs in the transportation industry, but also in association with other industrial process. Epidemiological studies have frequently indicated an elevated health risk for the spine in workers exposed to whole-body vibration. With regarding to train or bus operators, a fall of drivers’ wakefulness level because of fatigue is often pointed out. This decrease in wakefulness results in an increase of the occurrence of accidents. However, a study of how whole-body vibration affects people's level of wakefulness has not been done. To test the hypothesis that exposure to whole-body vibration has a certain effects on level of wakefulness, the change of a subjective wakefulness level and changes of electroencephalogram (EEG) were observed under experimental exposure to short-term whole-body vibration. Methods Subjects are ten healthy male university students, with an average age of 20.7 ± 1.8 years old, and they are all nonsmokers. Using the equipment (CV-300, AKASHI) of whole-body vibration generator, we consider an exposure environment of actual driver work, so that set the frequency and the acceleration level as 10 Hz and 0.6ms-2 r.m.s.. The subjects were exposed to whole-body vibration in the seated position and exposure time was fixed for 12 minutes. Subjective wakefulness level was evaluated using the questionnaire of VASS (Visual Analog Sleepiness Scale) and KSS (The Kwansei Gakuin Sleepiness Scale). For the electroencephalogram (EEG) measurement, it was equipped with the electrodes based on the International ten-twenty electrode system (C3-A2, O1-A2, O2-A1). EEG activity in the alpha frequency band (8 – 12 Hz) is one of the most typical physiological indicator which represent the transition from wakefulness to sleepiness. AAT (Alpha Attenuation Test) which repeats three times each opened and closed eye for 1 minute was performed in a seating position with directions of the researcher in the beginning, in the middle and in the end of exposure to whole-body vibration. For analysis, power spectral analysis was conducted over the last 6 min of EEG, and wakefulness levels were defined as the ratio of mean alpha power during eyes closed versus eyes opened. The laboratory was kept at room temperature (21 ± 1.0 degrees C), humidity was 50 ± 5%, noise level was 63.6 dB (A) eq, and illumination 510 lx. Each experiment was started around 10:00 am to minimize the effect of biorhythm.

Jan 6, 2006

Jan 1, 1969

By R. C. Ford, W. L. Niccoli, J. B. Finley

All mining operations are superimposed on natural hydrologic systems. As a result, mining operations are influenced by natural hydrologic processes and require water management systems to successfully conduct mining activities. Managing water and mining-related solutions is a critical task at all stages of the mine life because of the time-dependent nature of natural and mining-related flows. Effective operation of the mining water management system requires a “systems” approach that integrates the time-dependent effects of all water and mine solution handling components. This paper discusses the concept and application of dynamic systems modeling to address the time dependent nature of mining water management systems.

Jan 1, 2002

By C. Restarick, R. G. Robins, R. M. Taylor, I. Ennis

Lime addition to acid mine drainage waters (AMD), possibly accompanied by aeration, has been the basis for their remediation by precipitation of predominantly metal hydroxides. An efficient novel alternative technique causes precipitation of double M(II)-M(III) hydroxy sulfates which readily precipitate and are easily dewatered. When the Fe(II)/Fe(III) + Al(III) ratio of the AMD is appropriate, the Green Precipitate (GP) Process provides a more effective alternative to normal liming/aeration. The process can be adapted to give a continuous in-line treatment by the choice of suitable computer-controlled reactors designed to improve the liming efficiency, reduce scaling and control the rate of treatment. The processes are described in terms of the chemistry involved.

Jan 1, 2000

By Y. I. Rabinovich, S. C. Brown

In the Florida phosphate industry, fatty acid collectors are used to separate phosphate ore from silica during the rougher flotation stage. However, the presence of multivalent ions (in particular Ca++) in the processing water has been reported to result in the activation of silica with respect to oleate adsorption, rendering it floatable. Hence, adequate separation may not be achieved during the rougher flotation stage. In this study, the direct measurement of surface inter-action forces via atomic force microscopy was used to delineate possible mechanisms for calcium activation under phosphate flotation conditions at oleate/calcium concentrations both above and below the calcium dioleate precipitation limit.

Jan 1, 2004

By R. J. Sweigard, R. V. Ramani

G.F. Learning The paper by R.V. Ramani and R.J. Sweigard is a wonderful description of the labyrinthine web that has been spun about the mining industry by energetic bureaucrats and politicians over the past 50 years. The remedy for the problem, however, is not more of the same, but less. That may be difficult for the industry to achieve, for it is not a technical solution but a political one. And the current fervor for more detailed planning at all levels of government and private enterprise has become deeply ingrained. The authors recommend the provision of more information about mining and mineral resources to "macro" (i.e., government) land use planners. They apparently overlook, however, the already strong tendency on the part of most government land use planners to consider themselves omniscient. Thus, giving them more information about the technical problems of mining will only make them want to get more and more involved in the "micro" (private, site specific) mine development and production plans of the individual mining firm. In fact, this has already happened at all levels of jurisdiction from municipal to federal government. Examples are legion. The most effective way to ameliorate the adverse impacts of government land use planning on existing and potential mining operations is to: (1) introduce greater flexibility in the definition of land use zones by local and state governments; (2) adopt realistic and relevant ambient environmental performance standards in governing relationships between mineral land uses and concurrent or subsequent nonmining land uses; (3) allow greater leeway for economic considerations in land use decisions in contrast to the explicit legalistic approach now in vogue; (4) recognize that all minerals are not the same and that sand and gravel mining should not be treated the same as underground metal mining, coal stripping, oil field production, or in situ leaching; and (5) eliminate the notion that mining operators should be responsible for determining in detail the use of land by subsequent owners of mined land. This last bit of conventional ethic really makes no more sense than requiring the builders of every shopping center or government office complex to provide detailed plans for the use of that land when its use for shopping or government is ended. Did the builder of Ebbetts Field plan for Brooklyn after the Dodgers went to Los Angeles? Should the developer of the Bingham Pit plan for suburban Salt Lake City after the copper mining goes to Chile? The nation's mining industry must address these questions before further bankrupting itself to provide more data to planners and spending thousands of dollars per acre to create land that when reclaimed is worth only a few hundred dollars per acre. Reply by R.V. Ramani and R.J. Sweigard We thank Mr. Leaming for his valuable contribution. His views on the problems of land use planning and mineral resources are most welcome additions to our paper. As the title indicates, our paper was more concerned with the impacts of land use planning on mineral resource conservation than with the details of the planning process. On the whole, his five recommendations would be helpful for mineral resource conservation. However, we would suggest that the argument he presents for his final recommendation does not address the differences between mining as a land use and commercial or institutional uses. We believe that this difference is the crux of the issue. We share Mr. Leaming's desire to ameliorate the adverse impacts of land use planning. Possibly the most detrimental impact is the loss of mineral resources. Any development, whether mineral or community, that does not give proper consideration to other resources can result in permanent loss or sterilization of resources. With proper planning, some of these losses can be avoided. As our paper indicated, one factor that limits the consideration of mineral resources, and ultimately leads to their sterilization, is the generally inadequate levels of resource characterization and understanding of the unique nature of mineral resources and mining operations. The last point raised by Mr. Leaming is also important. In terms of reclamation and land use planning in mining districts, we certainly do not advocate spending more than what the results are worth. The main thrust of the paper was to explore the avenues for conserving the mineral resources so that, at some appropriate time, the issue of mining and reclamation can still be addressed.

Jan 4, 1985

The increased cost of imported oil fuels, coupled with our understandable reluctance to commit ourselves to the use of nuclear energy, has resulted in a renewed reliance on coal as a primary source of energy. New Zealand is fortunate in being fairly well endowed in its coal resources, but their exploitation until now, has been on a relatively small scale. Future exploitation, whether from underground or open cast mines, must be on a very much larger scale. This paper outlines some of the factors which should be considered in planning large open cast mines.

Jan 1, 1976

By H. Reginald Hardy

This report is Volume I of a three volume final report on the micro-seismic monitoring of a longwall coal mine. Volume I deals for the most part with the detailed aspects of the microseismic field study itself, however, brief references are made to other secondary studies described in Volumes II and III. During this field study a mobile microseismic monitoring facility and associated transducers were employed to detect and record microseismic activity above a longwall panel at Greenwich Colleries, Barnesboro, Pennsylvania. The fundamental objectives of this study were (1) to evaluate the feasibility of detecting microseismic activity originating from longwall mining operations using an approximately planar, near-surface, geophone array installed above the longwall and (2) to attempt to locate the sources of the various microseismic events. This investigation has proven that, using the techniques developed it is possible to detect microseismic events at depths of more than 400 ft and at horizontal distances in excess of 800 ft from the source. The majority of the observed events were found to have frequencies on the order of 10 to 100 Hz, and particle velocities of 50 to 300 µips. When a suitable velocity model was utilized, most of the events located were computed to be within ±100 ft vertically of the coal seam and ±50 ft horizontally of the longwall face. The results of the overall research project suggest that additional research should be undertaken in a number of associated areas.

Jan 1, 1978

By William Gleason

"It is safe to say that the coal industry, in the United States and globally, is currently suffering through one of the hardest times in its history.A perfect storm of competition, changing energy demands, politics and public perceptions have collided, inflicting significant harm to the industry that many say is irreparable. This, in turn, has led to massive job losses in some regions, heavy cuts in production and even bankruptcy filings from two of the largest coal mining companies in the nation.Cheaper natural gas can certainly take a large share of the blame for the struggle of coal, as utility companies switch from coal to natural gas for power generation. According to the U.S. Energy Information Administration (EIA) the amount of coal used for electricity generation in the United States is at a 45-year low.November 2015 marked the fifth consecutive month that natural gas was the leading source of power generation in the United States. EIA said generators produced 101,866 thousand megawatt hours (MWh) of electricity with gas in November versus just 87,789 thousand MWh with coal, the lowest monthly level since May 1980 when monthly coal use was 84,884 thousand MWh.According to Robert Godby, director of the Center for Energy Economics and Public Policy at the University of Wyoming, there are a number of factors playing a role in the decline of coal, but he points to the advances in fracking as the tipping point.“A lot of people will argue that regulation is the cause of the decline, and it has played a part, for sure, but the story of the recent past is more about what competition has done to the energy market,” Godby told Mining Engineering. “The war on coal was originally declared by natural gas in 2008.”The price of natural gas, which was at $13 per million Btu before the gas fracking boom, has fallen to as low as $1.68 in December 2015. Likewise, Godby said the cost of wind generation is now lower than the cost of generation from coal and the cost of solar generation is coming down as well. In addition to that, the demand for energy has changed in the past five years with more efficiencies in everything from building design to lightbulbs."

Jan 1, 2015

One of the important directions of further increase of quality and efficiency of control of mining companies and branches is the creation of the operation and development monitoring systems of such facilities. The main purpose of these systems is to provide managers with reliable and timely information on the current state and typical tendencies of operation of the facilities under control. However until the present time no scientific and methodical ground for system monitoring of the mining companies and branches has been created. Therefore, the authors of the report have aimed to assess the current situation with regard to the researches in this field and to do analysis of the most important aspects and ways of solution of the issue under consideration.

Dec 6, 2010

By Charles L. Kimbell

The year 1977 generally was a year of growth in overall world mineral industry activity, although there were downturns in major elements of the world's iron and steel industries. The sharp upturns in market economy nation activities that were noted in 1976, following the reduced performance levels of 1975, were moderated, and in the centrally planned economy nations, overall mineral industry activity apparently continued to increase, but at a pace in keeping with that of 1916 rather than at the higher rates of the earlier 1976's. Noteworthy during the year, if only in a negative sense, was the inability of world powers to reach any significant agreement on issues relating to deep seabed mining. Interest from a commercial viewpoint centered around deposits or so-called manganese nodules. These materials, which indeed are chiefly manganese in terms of their content on a quantitative basis, really were of commercial interest primarily far their copper, nickel, and cobalt content. Participants at the Third United Nations Law of the Sea Conference looked into seabed mining rights, but reached no mutually agreeable decisions.

Jan 1, 1981

By Poltak Sinaga

PT Kaltim Prima Coal?s 13-km (8-mile) overland conveyor (OLC) was commissioned in 1991. It is a conventional three-roller, 35 degree trough belt type. Cost and performance optimization during initial design resulted in a 5.4-m/sec (17.7-ft/sec) belt speed, 1,000 mm- (40 in.-) belt width to convey 1.35 kt/h (1,490 stph) and 7 Mt/a (7.7 million stpy) of coal. Despite a high initial figure, the belt speed was lifted to 6.5 m/sec (21 ft/sec) in 1996 to accommodate mine throughput in-crease. In 2002, a new low loss ST2100 1,100 mm- (43 in.-) wide belt replaced the ST2250 that was due to be changed-out. An upgrade project was initiated at the end of 2003 to further increase the belt speed to increase the OLC capacity to 30 Mt/a (33 million stpy). Upgrading the OLC by increasing the belt speed was the lowest capital option. Increasing belt width and/or modifying the trough angle to have larger cross sectional area was not an economical option because it would require expensive changes and significant down time of the OLC. To achieve 30 Mt/a (33 million stpy), the belt speed had to be increased to 8.5 m/sec (28 ft/sec). Although such high belt speed looked feasible, there was no information at that time of other OLC operating at such high speed. There was a risk that the conveyor would not operate safely and reliably at higher speeds. This risk was escalated by the fact there was no facility to lower or fine-tune the belt speed once the higher belt speed was implemented.

Jan 1, 2009