Search Documents

By Steinar L. Ellefmo, Fredrik Søreide

"The Norwegian University of Science and Technology (NTNU) and Nordic Ocean Resources AS, with support from Statoil ASA have carried out a project reviewing the knowledge about seabed mineral resources in Norway to identify and prioritize needs for further research and development.A special focus area in the project has been to increase the knowledge of possible massive sulfide mineralizations along the Mid-Atlantic Ridge. This Ridge is a subsea mountain range which separates the Eurasian and the North American continental plates. In this area, seafloor massive sulphides (SMS) are formed from the volcanic and hydrothermal activities along the Ridge. A large part of the North-Atlantic Mid-Atlantic Ridge between Jan Mayen and Spitsbergen is located on the Norwegian shelf.Analysis and interpretations of multibeam data have been carried out by NTNU in cooperation with the Russian Institute for Geology and Mineral Resources of the Oceans in order to disclose relevant areas for the formation of SMS deposits. This analysis has identified several promising areas."

Sep 1, 2014

By E. C. Grunsky, B. W. Smee

"The development of low-cost, rapid multielement analytical techniques has generated large geochemical databases in many exploration programs. When a sampling program consists of several thousand samples, the resulting data matrix is enormous and effective interpretation using all of the elements individually becomes burdensome. However, the application of multivariate statistical techniques can extract geochemical patterns related to the underlying geology, weathering, alteration and mineralization. Imaging the results over topography enhances the interpretation of these patterns. Examples of this approach are shown from mineral exploration programs in Canada and Mexico. IntroductionThere has been a dramatic change in the effectiveness of using geochemical survey data in the past ten years. This is mostly due to:• lower cost of geochemical analysis;• lower detection limits;• new methods of multi-element analysis;• a marked decrease in the turnaround time;and• the intelligent use of computers in presenting geochemical data.Geochemical surveys commonly have two objectives: locating abnormal concentrations of ore-forming or pathfinder elements and characterizing the underlying host lithologies. Geochemical surveys often employ a wide range of sample media that may typically include whole rock lithogeochemistry, various soil horizons, till and basal till sampling, stream sediments, lake sediments, and various forms of weathered regolith. Each of these sample media will exhibit a unique element distribution that must be factored in the interpretation phase of a geochemical survey study. This can become a cumbersome process if univariate data handling methods are employed."

Jan 1, 2003

Empirical methods involve the scientific interpretation of real-world experience. Many problems in ground control lend themselves to an empirical approach because the mines provide us with plenty of experience with full-scale rock structures. During the past 10 years, powerful design techniques have emerged from statistical analyses of large databases of real-world pillar successes and failures. These include the Analysis of Retreat Mining Pillar Stability (ARMPS), the Analysis of Longwall Pillar Stability (ALPS), the Mark-Bieniawski rectangular pillar strength formula, and guidelines for preventing massive pillar collapses. In the process, our practical understanding of pillar behavior has been greatly enriched.

Jan 5, 1999

By Oswald J. Heinrich

(with figures on plate V.) THE origin of spontaneous combustion in collieries is, of course, chiefly due to bad system in laying out the pits, unclean workings, insufficient ventilation, and neglect in damming off works after they are exhausted of the main coal. This is particularly indispensable in the Richmond field, because it is difficult and dangerous here, on account of the inferior roof, to remove the last vestiges of coal ; and we are compelled also to retain all the slates and bands, as far as possible, in the pit, to help fill up, although such material is liable to fire. This, however, can be prevented to a great extent, as men¬tioned below. I am satisfied that the only system of working this thick coal is by cross-cutting ( Querbau, ouvrage à travers) or working in benches, as practiced in France (Creusot, Rive de Gier, St. Etienne), in Sile¬sia (Königsgrube), which I have used as far as it is practicable in an old pit, almost torn to pieces by former workings. Modifications may, of course, be needed, even in the same pit, on account of irregu¬larities in the seam. I am also satisfied for economical reasons (on account of the heavy cost for timbering) that pits here ought to be worked upwards, even if it requires a longer period of time to win the coal, and a greater outlay of capital to commence with. The various saddle-shaped "troubles" making natural minor basins in the main basin aid in the execution of this plan. A pit worked once ought to be worked out clean, given up, and dammed off forever. If sections of proper height are assumed, according to the required amount of production for a certain period of time, they ought to be worked out and filled in as much as possible, dammed off, and ulti¬mately allowed to fill up with water, in order to protect the tipper works in future from fire in the gob below. This I consider indispen¬sable, because we may not be able profitably to fill in all the ground. To do so we have to use the waste of the mine, although it is liable to fire in time. In using this stuff, it ought to be surrounded by walls of rock not liable to take fire, laid firmly in clay, the gob being in the middle, and firmly covered and packed with clay on top. In

Jan 1, 1873

Study on Reasonable Mineral Processing Flow Sheet of Yunfu Low-Grade Pyrite Ores Low-grade ores in Yunfu Pyrite Mining Area were investigated, in order to find an economical, reasonable and environment-friendly mineral processing technology, which is of low consumption and high efficiency in pyrite recovering, which can ensure that the quality of pyrite concentrate product is eligible for sale and the sulfur content of the discharged tailings meets the national emission standards. A flow sheet with a classification, a jigging for coarse-grain minerals and a spiral chute separation for fine-grained minerals was adopted, and the sulfur grade and recovery of the pyrite concentrate is 35.50 per cent and 86.70 per cent respectively, while the grade of tailings is only 6.70 per cent.

Sep 13, 2010

By Jon Y. Kaneshiro, Sean A. Menge, M. Luis Piek, Brian Barker

The Lake Hodges to Olivenhain Pipeline project is part of a 40-megawatt pumped storage project linking two reservoirs as part of the San Diego County Water Authority’s $939 million Emergency Storage Project. Seeking to expedite project completion, the project was advertised as Design-Build, a first for the owner. Awarded to Kiewit Pacific with Parsons as designer, the 1,750m (5,700ft) long, 4.25-m (14 ft) horseshoe tunnel was excavated with conventional drill-and-shoot technique. The mining method was well suited to deal with the shear zones, the very abrasive rock, and 13.3% and19.6% grades. At the apex of the alignment, a 60m (200ft) by 3.6m (12ft) diameter raisebore shaft with surge chamber to protect against pump malfunction was constructed. Upon completion of mining, the tunnel was lined with a 3m (10 ft) diameter high strength steel pipe. Scheduled to come on-line by January 1, 2008, the Lake Hodges to Olivenhain pumped storage project is valued at $108 million, delivering a reliable source of water in emergency situations and electricity-generating capability to meet the growing demands of the San Diego region.

Jan 1, 2007

Many sampling standards arrive at a value for the prescribed sample mass by assuming a specific relation between the sample mass and the relative standard deviation of the fundamental error and assigning a value to the tolerated coefficient of variation. In order to obtain an equation that provides a relation between the minimum sample mass and the particle properties, many different models for the drawing of a sample have been developed. Here, a model for the drawing of a sample is proposed which can be considered to be a generalisation of the model used in GyÆs sampling theory. Using simulations, it is illustrated that the generalised model can lead to a better correspondence with actual sampling processes.

Jan 1, 2005

By Mark L. Chatman

This report presents an economic mineral assessment and Inventory of mines and prospects In the approximately 176,000-acre Patagonia Mountains-Canelo Hills Unit of Coronado National Forest. Deposits or areas most likely to experience future development are characterized in terms of their economics, based on data acquired by the author from a variety of sources, and supplemented by USBM field data collected by other workers in 1990 and 1991. Numerous mine maps, rock-chip sample assays, and detailed descriptions of mine and prospect sites are in this report and appendixes. Heavy but sporadic mining, mainly between the 1850's and 1950's was nearly all confined to the Patagonia Mountains. High-grade sulfide veins, replacements, and skarn deposits accounted for most of the production, which included large quantities of zinc, lead, copper, and silver, and considerable quantities of gold. Small Quantities of molybdenum, manganese, tungsten, and placer gold have been mined. Most of the traditionally mined metalliferous sites will not see future activity due to the low tonnages present and removal of most high-grade rock. Possible future development areas include copper porphyries and breccia pipes; most are too deeply buried for current development. Localities where similar deposits may be concealed are identified.

Jan 1, 1994

By Bengt H. Fellenius

The bearing capacity equation?"the triple N formula"? is now about 50 years old. It was developed from theory of plastic resistance of metal to a cone being pressed into the surface of the metal, superpositioned by resistance due to shear in an interparticulate medium (soil; note, we are not dealing with metallurgy), and tempered by work necessary to move the footing into the medium. The equation (and its coefficients) was "confirmed" by tests on small footings placed at or near the surface of the soil. The equation is a basic tenet of every geotechnical textbook, manual, and code. Over the years, innumerable variations of the N-coefficients and adjustments to the equation have been published. The main assumption behind the bearing capacity equation is that a shear plane develops between two essentially otherwise unaffected bodies: the main soil body and a body comprised of the footing with some soil. Moreover, the notion is that a model footing placed at or near the surface of a soil would behave proportionally or similarly to a full-scale footing, or to even a same size footing (pile toe) placed at some depth in the ground. This is not in agreement with factual observations. It is suggested that the behavior of a small or large diameter footing as well as a pile toe is governed by compression of the soil below the footing or pile toe and not by "bearing capacity".

Jan 1, 1999

By S. K. Kawatra, S. J. Ripke

Bentonite clay is used as a binder for iron ore concentrate pelletization. Bentonites are sensitive to cations such as calcium, magnesium, sodium, and potassium that are known to be dissolved in the moisture remaining in the iron ore concentrate. These cations affect the ability of bentonite to absorb water, as measured by the plate water absorbance (PWA) test. This paper addresses the relationships between plant water chemistry and pellet strength for a wide PWA range of bentonites. Experiments were conducted to determine the effect of concentrate moisture solute chemistry and bentonite PWA value on the wet knock and wet and dry compressive strengths of iron ore pellets. Experiments used seven different types of bentonite that had PWA values ranging from 564 to 1033. Flushing plant concentrate with distilled water to remove the dissolved cations resulted in increased pellet strengths, to a widely varying degree, for each bentonite tested; wet knock values increased an average of 92% and dry compressive strength increased an average of 46%. In addition, pellet strengths were not found to be directly related to the ability of bentonite to absorb distilled water, measured by the PWA test.

Jan 1, 2002

[ ]

Jan 1, 1938

By P. -É. Boileau, VibRG, S. Grenier, M. Smets, T. Eger, J. Stevenson

Load-haul dump vehicles (LHDs) are used to move waste rock and ore in underground mining operations. The LHD is designed for bi-directional operation and the driver sits sideways to the direction of travel. LHD operators have higher reports of low back pain and neck discomfort than other mobile equipment operators who do not sit sideways in the vehicle, but are exposed to whole-body vibration (WBV)1. Exposure to WBV is linked with reports of lower-back pain, neck problems and spinal degeneration2,3. Static sitting postures, sitting with the neck and back twisted, and sitting with the back in an unsupported posture are also linked with an increased risk of developing back pain4. The objective of this study was to determine typical vibration exposure levels and driving postures for LHD operators. Methods Whole-body vibration exposure was measured at the seat-pan, in accordance with the ISO 2631-1 standard5, on seven LHD vehicles with a 10 yard bucket haulage capacity. Vibration data were recorded with a Biometrics™ DataLog II (P3X8) and stored on a 128 Mb Simpletech™ multimedia card. Comparisons were made to the ISO 2631-1 Health Guidance Caution Zone (HGCZ) in order to determine potential injury risk. Operator posture was monitored with three digital video cameras which were secured inside each operator’s cab to the top left corner, top right corner and back right corner. Reflective tape was placed on each driver’s shoulders, head, and back in several locations and in several locations on the vehicle seat in order to aid in posture coding. Posture coding was performed with 3DMatch v4.50 multiple video view analysis feature. Vibration measurement and posture recording occurred simultaneously for 60 minutes while the LHD operator performed typical duties. Results and Discussion Results indicate LHD operators may be exposed to whole-body vibration levels putting them at risk for injury (Table 1). According to ISO 2631-1 the frequency weighted acceleration values corresponding to the lower and upper limits of the HGCZ (for an 8 hr exposure duration) are 0.45 and 0.90 m/s2 respectively5. Six of the seven vehicles showed exposure levels within the HGCZ defined for 8 hours. Preliminary video analysis indicated LHD operators were exposed to potentially harmful levels of WBV while adopting asymmetric postures (Table 2). For example, one LHD operator (Figure 1) worked with his neck twisted greater than 40 degrees for 93 % of a 60 minute work cycle. According to the Swedish National Work Injury Criteria, neck rotation should be less than 15 degrees if the motion is required for greater than 80% of the work time6. Results of this study highlight the need to further examine the contribution of non-neutral working postures and

Jan 6, 2006

By Robert J. Kuhne

The Iron Ore Company of Canada has successfully employed advanced process control (APC) to optimize the operation of their induration machines. A significant increase in machine throughput and a reduction in fired pellet quality giveaway were observed following the APC implementation on all six machines. This paper discusses the opportunity for process control optimization in induration, reviews the property estimation and multivariable control technologies, and describes how the IOCC control strategy captured this opportunity. APC performance data is presented. The dependence of APC performance on control room operator acceptance, process equipment and instrumentation is highlighted.

May 1, 2007

By J. Matos e Silva

The paper refers five examples of executed diaphragm walls with one to five levels of anchorages. For each example a comparison is made between the results of the design using the traditional criteria and the Eurocode 7 recommendations. A comparison is also made with the behaviour of the diaphragm walls during the construction phase. From the referred examples the author presents his conclusions.

Jan 1, 2002

By B. P. Sereda

The properties, characteristics and phase structure of chamotte refractories produced with the usage of mullitecorund chamotte and caoline have been given. The comparison of new refractory C-45 obtained by us and refractory C-43 produced by traditional method has done. The physical-chemical properties of refractories is reviewed. The visual porosity, density and pore characteristics of given refractories was calculated. It is established that C-45 has the less gas permeability then C-45 that gives melting units more stability. The petrographical microstructures of refractories have been done. The main phase structures and their influence on refractories properties have been observed. It is established that refractories with mullitecorund chamotte adition has more advantages then refractories gained by traditional method and can be applied to melting units.

Jan 1, 2010

By W. Mackenzie

The development of a resource project inevitably requires the investigation of a vast range of issues across most engineering disciplines - mining, metallurgical, chemical, civil, electrical, mechanical and environmental - as well as the geosciences. It is also a characteristic feature of the resource industry that no two orebodies - and hence no two development projects - are the same. So these technical issues have to be addressed to a greater or lesser extent in evaluating any resource project's development potential. Not surprisingly then, technical issues tend to predominate when assessing the development potential of a project in the process typically referred to as `doing a feasibility study'. But the principal purpose of a `feasibility study' is to determine whether a development opportunity makes good business sense, not just whether it is technically possible. Resolution of technical issues is often seen as the primary focus of a feasibility study, whereas in reality, these technical issues are the basis upon which an asset delivery and business plan is built. This is not to say that technical issues are unimportant - they are a prerequisite to the demonstration of a project's viability. The feasibility study process must therefore demonstrate that not only have the technical issues been satisfactorily addressed, but also that the broader commercial, economic and social issues have been considered in the development of a comprehensive business plan, which includes an assessment of the risk-reward profile of the proposed development. This paper will present a framework for the conduct of `feasibility studies' and provide guidance to minimum standards and best practice.

Jan 1, 2007

By Robert G. Gibson, Joel D. Gibbons

Measurements and analyses were conducted of whole-body vibration aboard seven commercially available passenger and/or recreational vehicles: sedan; sport-utility vehicle (SUV); pickup truck; moving truck; motorcycle; all-terrain vehicle (ATV); and boat. The purpose of the testing was to measure and assess whole-body vibration exposure in a range of typical vehicle environments in order to gain understanding of typical exposure levels characteristic of activities of daily living. Vehicle models tested (and model year) were: Ford Taurus (1995); Jeep Cherokee Sport (2000); Toyota Tundra SR5 (2002); Ford F-350 (1997); Harley-Davidson Electra Glide Classic (2004); Yamaha Kodiak 400 4x4; and Steiger Craft Model 21 Montauk. All vehicles were tested with their standard factory-installed seats and were operated under a range of normal operating conditions and speeds typical of intended vehicle use. Methods The measurement, processing, analysis, and exposure assessment methods follow the guidance of generally accepted, national and international consensus standards relevant to the evaluation of whole-body vibration, including ISO 2631-1 [1] and ANSI S3.18 [2]. Seats were instrumented with low-mass triaxial accelerometers mounted in seat pads. Accelerometers used in the test are specified to have flat frequency response over the frequency range of 0.5 to 80 Hz, and all accelerometers were recently calibrated traceable to the National Institute of Standards and Technology (NIST). Seat pads were installed following guidance in the relevant standards [1, 2], with sensitive axes of the accelerometers following the standard coordinate system with respect to the seated occupant. (The x-axis represents fore-aft motion; the y-axis represents side-to-side motion; and the z-axis represents vertical motion with respect to the occupant.) Vibration data processing and analysis, including filtering, sampling, frequency-weighting, averaging, summation, and determination of basic and additional metrics followed procedures in the relevant standards [1, 2]. Digitized time series data were acquired and stored using a PC-based data acquisition system. Whole-body vibration exposure analyses were conducted via post-processing. During data processing, recorded periods of seat acceleration that were identified and verified as resulting from occupant-induced motion rather than vehicle motion were excluded prior to exposure analysis. The basic evaluation metric for whole-body vibration is the frequency-weighted root-mean-square (r.m.s.) acceleration, aw. The primary additional evaluation metric is the fourth-power

Jan 6, 2006

By Peter Cain

Longwall extraction in the Phalen Scam in the Sydney Coalfield of Nova Scotia is carried out under flooded abandoned workings in the Harbour Seam 140 m above, and at depth of up to 700 m beneath the Atlantic Ocean. Careful planning of panel and pillar dimensions is necessary to prevent inflows from the overlying workings and to prevent the development of excessive subsidence strains at the seabed. This paper briefly summarises the research undertaken over the past five years by CBDC and CBCRL into the problems associated with mining under water, and then describes the development and application of a design/planning code of practice developed jointly by CBDC, CBCRL and mine regulatory agencies. The design method employed in the Code of Practise is based on empirical data from the coalfield and parameters developed from subsidence modelling and previous water inflow experience. It includes precautionary measures to be adopted during development and mining, and monitoring procedures to be followed. It is flexible enough to allow future developments in the understanding of inflow mechanisms to be incoporated without major modifications, and represents a major step forward in reducing the potential hazards associated with coal extraction in the coalfield.

Jan 1, 1996

Most mining operations have been happy to live in blissful ignorance of what their equipment is really capable of. Shareholders have been shown increasing tonnes output per employee (due to rationalising employee numbers). It is now known that the best practice for large mining trucks is 52 per cent higher than average or best practice for excavators is 41 per cent higher than average, or 38 per cent in shovels or 35 per cent with draglines, etc. The data is available. The bell curve of performance is flat. Substantial underperformance is rife. If you are working in or supplying equipment or services to one of the majority of operating mines that donÆt achieve best practice surely you want to know why. Or maybe you donÆt? For many mining people this sort of knowledge could be dangerous to their career so keeping the MD or CEO in the dark is a good option. Many suppliers donÆt want the performance of their equipment benchmarked? Mining consultants donÆt have the data so they are happy to keep guessing. Unfortunately, many Business Improvement or Business Excellence projects are about ticking the participantÆs æcareer boxesÆ. The first step to capacity utilisation is knowing what the capacity is. Even then people and culture will get in the way. People are the biggest hurdle to capacity utilisation. This paper will discuss what the mine of the future (and today) will need to do to utilise the productive capacity of its assets. It is not just benchmarking. It is not just automation. It is not just technology. It is about engaging those people who impact on equipment performance; right from the operator up to the Mine Manager. Doing it better involves a process to facilitate change and a culture which says it is OK to try even if you are wrong.

Jan 1, 2009

Technical disputes, commercial negotiations and workplace/societal conflict are a natural part of doing business and just living itself. Conflict is everywhere û at home (between family and neighbours); in the workplace (between management, co-workers and unions), with contractors and with other companies; and everywhere at the community level, dealing with land access (pastoralists/farmers and indigenous/First Nation people), environmental protestors and NIMBY-ites - Civil Society in general. Exploration and mining companies, operating in more remote, less developed and culturally diverse regions, tend to encounter myriad areas of conflict (typically emotion-charged) and they are outlined. Dispute prevention, management and various binding and non-binding resolution techniques are discussed. The paper gives a general overview of the ADR nomenclature and framework (mediation, conciliation, expert determination, adjudication, arbitration and litigation) encouraging technical professionals to participate. Its thesis is that lawyers should not necessarily be the first port of call when problems arise between the mining workforce, contractors, joint venture partners, purchasers of prospects/mines, traditional land owners, protest groups, etc. If the matter must be litigated, the role of the expert witness is critical in pretrial planning, negotiations, mediation and litigation management, so a few guidelines are provided. Whilst dispute resolution has a legal context, the paper is written from an AusIMM technical professionalÆs perspective, emphasising practical long-lasting pragmatic solutions.

Jan 1, 2006