Search Documents

By T. J. Ballard

"INTRODUCTION The Buck. Creek corundum area of Clay County, North Carolina, includes one of the largest single masses of peridotite outcrops in the whole Appalachian Range and has been described by Pratt, an early authority on corundum, as offering one of the best potentialities for corundum production in North Carolina.Two principal types of corundum deposits are found at Buck Creek the vein type and the corundum-bearing amphibolite dikes.The vein deposits occur in structural fissures that strike north to northeast in a gangue of feldspar, zoisite, an, chlorite. The corundum is generally coarse-grained and good-quality. The corundum content varies from several percent to 50 percent.The corundum in the amphibolites is more or less disseminated through the dike, is generally lower-grade, and is less in quantity, than the vein corundum. About 50 percent of the amphibolite corundum is coarse enough for snagging-wheel grade but is difficult to separate from the amphibolite.Production from the Buck Creek area has been small and came mainly from high-grade pocket in the vein deposits. Pratt 3/ reports 300 tons of corundum ore was produced to about 1896. No record of subsequent production is available.The critical shortage of corundum during the war, due to transportation difficulties and the depletion of deposits abroad, prompted the Bureau of Mines to investigate domestic reserves.After a favorable report was obtained on the Buck Creek area, the Bureau began exploration of the deposit in September 1943 and continued until February 1945."

Apr 1, 1947

By S. Acar, M. Botz

Introduction In 2007, Newmont Mining Corporation will begin construction of a milling and cyanidation leaching circuit for the Yanacocha site in Peru. Ore to be processed in the circuit contains a relatively high level of cyanide-soluble copper, and as a result, leach solutions are expected to contain elevated levels of copper and WAD cyanide. As the means of controlling copper levels in leach solution, a circuit will be installed to precipitate copper sulfide from barren solution using sodium hydrosulfide. In addition, a circuit will be installed to recover cyanide from barren solution, with recovered cyanide to be returned to the leaching circuit and treated solution to be utilized as make-up in existing heap leaching facilities. As needed to support design of the copper precipitation and cyanide recovery circuits, pilot testing was conducted in 2005 to determine preferred operating conditions and evaluate the performance of the processes. This paper presents results from the pilot testing where 99% copper reduction was achieved and 95% to 98% cyanide recovery was achieved.

Jan 1, 2007

By Lon D. Santis

This paper summarizes explosives transportation incident and accident data collected by the U.S. Department of Transportation (DOT) from 1993 to 1998. The paper briefly describes the legislation and regulations that cover hazardous materials transportation. The multimodal incident data collected by the Research and Special Programs Administration (RSPA) contained 86 incidents involving Class 1 materials during transit. Thirty-two occurred on public highways. The Federal Highway Administration (FHWA) data showed there were 8 1 motor-vehicle accidents involving explosives. The FHWA Crash datafile extract contained 649 records categorized as involving Class 1 materials although closer analysis revealed that nearly 90% of these did not involve explosives. In both databases, there were no fatalities caused by the explosive materials although 7 fatalities were the result of injuries suffered during the motorvehicle accident. There were also no serious explosions during any of these incidents or accidents. The paper concludes with an analysis of the risk involved with transportation of commercial Class 1 materials on the highway.

Jan 1, 2000

By Horacio Reeves

Las maquinarias son elementos importantes en el proceso de minería de tajo abierto -en tanto optimizan el rendimiento del trabajo y de los operarios. Sin embargo, su contínuo uso conlleva riesgos ocupacionales en el trabajador como la exposición a vibraciones de cuerpo entero en el caso de equipos pesados. En ese sentido, el presente texto compara los niveles de vibración en los equipos pesados que operan en Antamina con el estándar europeo: Directiva 2002/44/CE, así como los efectos de este en los operarios.

Sep 12, 2005

Coal mining in Indiana is limited to the south-western portion of the state, with coal currently being recovered in 19 counties. The coal-producing area of the state covers approximately 6,500 square miles. Although most of the coal in Indiana is recovered by surface mining methods, a small percentage is recovered through underground mining. To date, 40 percent of the known coal reserves have been removed. Indiana has about 33 billion tons of identified coal reserves, of which approximately 17 billion tons are recoverable using current technology. Of this recoverable coal, about 15 billion tons are recoverable by underground mining and 2 billion tons are recoverable by surface mining methods. The State of Indiana has regulated the environmental impacts of coal mining since 1941. Indiana was the second state in the nation to pass legislation requiring mined land reclamation. Its SMCRA regulatory program was approved July 29,1982, and its Abandoned Mine Land Program was approved July 29, 1982.

Jan 1, 1992

Maghemite - A Source of Heavy Medium for Coal Washeries Use of magnetite as heavy medium in coal preparation plants has been increasing steadily in recent years. It might be in short supply in some areas or excessively costly in certain times. In Turkey, the cost of heavy medium magnetite has almost tripled since 2003. As a result, alternative sources of heavy medium material have been evaluated. A maghemite ore from Elbistan-Kahramanmaras was found to be an interesting source. Tests showed that the maghemite ore can be enriched via magnetic separation at 1556 gauss to obtain a heavy medium material with 4.93 g/cm3 density and 97.22 per cent magnetic recovery. Further tests were conducted to determine the optimum field strength for magnetic separation, friability and regeneration recovery.

Sep 13, 2010

By D. Brunner, G. R. Baiden, H. J. Yazici

System simulation is an increasingly popular technique for analyzing and improving existing as well as newly designed underground mining operations. An engineering firm that specializes in simulation helped a major metals producer build a long-range planning model of an existing underground mine. Subsequently the team adapted this model to assess technology alternatives in the design of a new mine. The two models differ in the level of detail used for modeling the development process. This paper discusses the differences in approach between the models along with the experiences gained and challenges faced during the construction and use of the models.

Jan 1, 1999

By K B. Quast

Changes in feed size distribution can have significant effects in rod mill grinding. The product sizing resulting from wet batch milling of a tin ore showed little influence on fines production after truncating the feed at either the coarse or fine end. The addition of fine material caused a less amount of fines to be produced and a possible increase in grinding at coarse sizes, although this is complicated by the changing feed size distribution. The changes in feed size distribution caused no tendency for preferential grinding of the cassiterite.

Jan 1, 1998

By Sean Gallagher

The vast majority of ergonomics research has addressed the demands of work in standing or sitting postures, and understandably so. However, many workers (for example, underground miners, aircraft baggage handlers, plumbers, agricultural workers, mechanics, and others) are often required to adopt postures such as kneeling, stooping, squatting, or lying down for significant periods of the work day.

Jan 1, 2005

By M. C. Roberts

As nations advance through various stages of economic development, the patterns of demand for minerals change. For example, as a nation develops from a subsistence economy through industrialization and into a service based economy, the use of minerals is at first low, then grows rapidly, and finally stabilizes. The past trends in the use of agricultural minerals by the currently advanced nations provide a pattern that the world as a whole may follow as it progresses through the stages of economic development. Future needs for agricultural minerals are estimated using this approach.

Jan 1, 2001

By Patiño E

Bioleaching is an established technology for the pre-treatment of refractory gold ores and concentrates and the leaching of whole ore copper heaps. In many cases, it offers economic, environmental and technical advantages over pressure oxidation and roasting. However for bioleaching to compete successfully with others pre-treatment processes it needs to be optimized with regard to the parameters that affect the bioleaching reactions and the growth of the microorganism involved. In this sense, this paper focus on the thermodynamic approach applied in bioleaching through of the definition of the growth system and it is thermodynamics analysis, the effect of heat production and energy dissipation on growth and thermodynamic analysis of growth kinetics and the effect of nonstandard conditions.

Sep 12, 2005

By N. A. Gokeen, M. Ohtani

EFFECT of elements on the solubility of carbon in liquid iron is useful in calculating and correlating a number of thermodynamic properties as shown elsewhere in detail.' Kitchener, Bockris, and spratt2, and later Turkdogan and Hancock3 have investigated the effect of sulfur on the solubility of carbon at various temperatures and concentrations. For any chosen sulfur concentration, the solubility of carbon reported by Kitchener et al. is considerably lower than that by Turkdogan and Hancock. It was therefore felt that a reinvestigation of this problem was necessary. EXPERIMENTAL METHOD An alloy of Fe-C-S .was prepared with electrolytic iron and ferrous sulfide melted by induction in a graphite crucible, 4 in. high 1 1/2 in. ID under a CO-atmosphere. The temperature, held at 1500" ± 5°C in all experiments, was measured with a Pt-Pt + 10 pct Rh thermocouple immersed into the melt. In order to assure saturation with carbon, the melt was stirred with a graphite rod. After approximately 1 hr at 1500 °C, a sample was obtained by sucking the melt into a silica tube, 4 mm ID. The sample was then analyzed for carbon and sulfur by usual methods. RESULTS The results are presented in Table I and plotted in Fig. 1 with the individual values of Turkdogan and Hancock.3 Scattering in the data is equivalent to 3 pct or less in carbon analysis. The broken line represents the empirical equation obtained by Kitchener et al. from their data. It is evident that the present data are in good agreement with those of the former investigators but in disagreement with the latter. The cause for this discrepancy cannot be readily offered since the experimental methods in the three investigations were nearly identical. Additional evidence corroborating the author's results may be presented in the following manner. The difference between the solubilities of carbon in the ternary Fe-C-X melt with a small concentration of any element X, and in the binary Fe-C melt is %?C = %CIII-%CII [1] where %?C is the change in solubility, and %CIII and %CII are the solubilities in the ternary and the binary systems respectively. The value of %Cii

Jan 1, 1961

By K. Oraee

Mining Ventures are considered as high risk projects and therefore managing the risks is inevitable. Risk assessment is an important part of the complex process of risk management, hence applying appropriated and practical methods for ranking the risks associated with projects, can help to perform a better risk management. In this research the applicability of using Techniques for Order Preference by Similarity to Ideal Solution (TOPSIS) method for risk ranking in an underground mine, extracting by block caving method, was studied. Via this method, the risk associated with reserve estimation ranked as the first while in conventional method (P-I Matrix method) located in the sixteenth. Also there were significant differences in ranks of the other risks. Considering the more criteria, with different weights, in comparison with conventional methods, the results comprised from TOPSIS method are more reliable. By implementing this method risks are ranked better and more realistic and consequently then will be managed more efficient.

Jan 1, 2011

By Harvey W. Parker

The underground industry is challenged by many complex technical and non-technical issues and risks. The most obvious of these are the traditional technical issues that we usually try to address with risk management techniques. However, there are many other non-technical risks that our projects face on a daily basis which we often fail to fully recognize or appreciate. This paper addresses some of the less-technical broad-based risks in order to put them into perspective with the technical risks we face day to day in underground planning, design and construction. The good news is that Risk Management techniques are not always about bad things. For obvious reasons Risk Management is always thought of in terms of the ?downside? of risk (i.e., the identification and mitigation of things that can go wrong). On the contrary, there is an ?upside? of things that might go better than expected. Fortunately, if a deliberate effort is made, the same principles and techniques that our industry uses in Risk Management can be applied toward identifying and quantifying the Opportunities and Benefits that might occur. In this way, the process of conducting risk management programs can not only identify the downside risk but can be used to identify and direct projects to take advantage of the upside of uncertainty (i.e., Opportunities as they arise). This beneficial aspect of risk management programs will be highlighted in this paper together with the importance of the non-technical issues.

Jan 1, 2008

By V. E. Chrapunov, T. V. Chnyrenkova, R. A. Isakova, V. A. Luganov

Arsenic-gold bearing ores are used as a flux in smelting or leached out to extract gold. To decrease arsenic content in processed materials and to break up the lattice to free the gold, raw materials are roasted. This article analyses the results of laboratory and pilot testing of dissociating and oxidizing roasting of gold-arsenic bearing concentrates. During the dissociation roasting under vacuum arsenic is sublimated into elemental and sulfide forms. The process allows to minimize the negative influence on the environment but requires costly engineering solutions. Roasting in a neutral medium or with limited quantity of oxygen in the gaseous phase makes it possible to sublimate arsenic in the form of oxides and sulfides and may be carried out in the autogeneous mode in fluid bed furnaces. If oxidizing roasting of the concentrates is done in the presence of soda, practically all arsenic and sulfur form water-soluble compounds and remain in cinder.

Jan 1, 2002

By Joseph Haid, om, Rio Yang, Kelly Fleetwood

Some coal mining operations in the Powder River Basin are currently observing a number of blast holes detonating sympathetically within their cast blasts. Sympathetic detonation can cause poor cast results, high blast vibration levels, excessive back break and fly rock, along with a number of other undesirable blast results. The reduction or the total elimination of blast hole sympathetic detonation is of paramount importance to the coal mining companies operating in the Powder River Basin. This paper describes a systematic approach to prevent cast blast holes from detonating sympathetically through the use of the electronic initiation and expanded blast patterns. In-situ measurements outlined in this paper were recorded from pressure probes, velocity of detonation probes and near field accelerometers, along with digital images generated from a high speed CCD camera. Large diameter angled drill holes were also checked for any measurable amount of deviation by a cable type borehole measurement tool. The field measurements provided the scientific evidence, statistical data, and documentation necessary to develop a sound method or a “road map” that would minimize and in some situations prevent the occurrence of blast hole sympathetic detonation.

Jan 1, 2005

By D. Jepsen

Land access and tenure certainty for exploration and mine development is absolutely critical to the foundation of a healthy, sustainable and environmentally-sound mineral exploration and mining sector. Without certainty, mineral exploration will be severely eroded, resulting in reduced possibility of discovering and developing new mines. The development of positive relationships based on a shared commitment of understanding, mutual respect and trust by First Nations and the mineral sector can provide this increased business certainty and social and economic benefits for local First Nations. As a sector, we face many challenges in regard to building relationships with First Nations. The root solution to addressing these challenges lies in recognizing and understanding the unique cultural differences that exist between indigenous people and the business community. From the Canadian perspective, the First Nations culture differs vastly from non-Aboriginal culture. It is equally as imperative that cultural differences be acknowledged and respected at home as they are when seeking business opportunities in other countries. The traditional “business” approaches and relationships that one understands and incorporates with one’s contractors, legal counsel, investors and Board are generally not be the best approach for the introductory and subsequent meetings with indigenous peoples. This paper is written from the perspective of my experiences accumulated over the past ten years, first as Manager of Aboriginal Affairs for one of the largest forest companies in British Columbia and now, as President and CEO of the Association for Mineral Exploration BC (AME BC). My opinions are not necessarily endorsed by AME BC. Before the gritty issues of consultation and benefit sharing are dealt with, it is worthwhile to clear up the confusion surrounding terminology. “Indigenous Peoples” is used in a global context; “Aboriginal Peoples” is used in the Canadian context therefore includes Métis, Inuit and First Nations Peoples. The term “First Nations”, in the context of British Columbia, perhaps has its roots in the fact that treaties have largely not been settled. Therefore it is important to reaffirm that British Columbia was not discovered. First Nations have resided in British Columbia since time immemorial.

Jan 1, 2007

The Beginning ! The status quo simply isn?t sustainable ! Our social license is at risk ! The bar keeps rising ? We must improve our performance, both operational and social ? We must improve stakeholder judgement of our industry by taking action collectively Implementing TSM " TSM Guiding Principles " Performance Indicators " Crisis communications " External Outreach " Tailings management " Energy management " Performance manuals, guides " Reporting " Communities of Interest Advisory Panel

May 1, 2004

By A. A. Paoli

The selection of a mining plant for carrying on development work presents many problems distinct in themselves, and affected by various local factors. In this paper, the writer proposes outlining and discussing in some detail the chief factors governing the economic selection of such plants. This will be followed by an enumeration of the underground and surface plant required for carrying on several hypothetical exploratory and mining operations. Where it is impossible or not convenient to obtain hydro-electric power, and where wood for fuel is scarce, we now find oil engines being used. A 100 h.p. oil engine, such as would be required to operate a three-drill air compressor, consumes approximately five Imperial gallons of fuel-oil per hour at full load. On the basis of a 60 per cent load factor, this gives, for eight hours' operation, a probable actual consumption of twenty-four Imperial gallons.

Jan 1, 1929

By M. J. Hannan

Considerable interest has arisen in developing analytical methods suitable for measuring resource commodity substitution patterns. some of this work has applied the Translog method to estimate actual elasticities of substitution. Recent examples incl.uae Privolos and Dunietz (1987), Kopp and Smith (1983), and Moroney and Trapani (1983). Another method, one which has received attention earlier in the work of Fisher and Pry (1970), is that of the logistic or diffusion function. We believe that the latter method has properties suitable for analyzing current problems of material substitution. The present study thus evaluates this method in its original logistic form as well as an extended version incorporating additional explanatory influences. The analysis is applied to copper/aluminum substitution and iron ore beneficiation. Substitution for copper by aluminum is examined in the building wire and cable, and magnet wire end-use markets. For iron ore, the substitution of pellets for sinter is considered for the U. S. market.

Jan 1, 1990