Search Documents

By Homer W. Riley

ANTHRACITE SMALL power-driven, toothed, cast-iron rolls were used first to break anthracite in 1844. Prior to that time, men with hammers, who stood on perforated cast-iron plates, broke the large lumps into commercial sizes. In order to convert run-of-mine into the various sizes required by the anthracite industry, about 20 million tons must be broken, annually, into smaller sizes. This phase of anthracite preparation is of major importance, because the degradation accompanying reduction in coal sizes should be kept at a minimum. The exclusive use of toothed rolls for that purpose indicates that comminution by rolls is the best solution of the problem. Many improvements have been made in tooth design, but the most important was a reduction of the peripheral speed of the rolls from 1000 to 300 ft. per minute. The higher speed was based upon and approximated the velocity of a falling piece of coal when it entered the rolls, Exhaustive roll tests at the slower speed showed that the same size reduction could be affected with less degradation. The adoption, therefore, of slow-speed, compound geared rolls, especially for breaking the larger sizes, became quite general after 1912. A high-speed roll is shown in Fig. 1 and a slow-speed roll in Fig. 2. Anthracite Crushing Problems.-Crushing anthracite presents the problem of selecting a series of rolls that will produce the greatest percentage of the prepared sizes of nut and over. The size distributions to be expected are shown in Table 1. Coal breaking and crushing practices in anthracite breakers involve the use of equipment for comminuting the following classes of material: 1. Run-of-mine-plus 6 ½ -in. coal. 2. Sized coal-steamboat, broken, egg, stove, nut, and pea. 3. Flat coal--coal that is flat and hence not suitable for the market. 4. Bone--a piece of laminated coal and slate, crushed for the purpose of reclaiming the coal. 5. Breaker refuse, reduced to a size suitable for flushing into a mine for back-filling purposes.

Jan 1, 1950

By H. E. Heide

"Before the war, the United States was the world’s leading consumer of tin, the industrial applications of which had become widespread. Domestic production was negligible, and requirements were met almost entirely by imports, principally from British Malaya, United Kingdom and China. Average annual imports for the years 1925-1929 amounted to 78,009 long tons.With the advent of war in Europe and signing of the Japanese-German pact, it was realized that foreign sources of supplies were threatened, and steps were taken by Congress to forestall critical shortages of tin and other minerals. These steps in regard to tin included stock-piling, improving reclamation and conservation, increasing South American production, constructing a smelter in the United States for treatment of tin, ores, and intensifying the search for domestic tin deposits. Annual imports were raised to 140,873 long tons by 1941. On 1945, annual imports had shrunk to 37,675 long tons and consumption had been reduced to 52,100 tons of primary and secondary tin but not tin content of scrap alloy.The Strategic Minerals Act, passed by the Congress in 1939, authorized the investigation of domestic tin deposits.As Alaska had supplied virtually all of the domestic output of tin, an investigation of Alaska deposits was undertaken in 1940 and 1941 by J. B. Mertie, Jr., and Robert R. Coats of the Geological Survey.The Lost River lode tin mine on the Seward Peninsula was examined by H. E. Heide of the Bureau of Mines in 1942. Possibilities for developing a significant amount of tin appeared favorable, and exploration of the ore bodies was started in August 1942."

Jul 1, 1946

By Rodney D. Lamond

The need for blast vibration monitoring can be attributed to a combination of three factors: Structural damage, Blast design and Human annoyance. Traditionally, vibration damage criteria are prescribed in terms of peak particle velocity (PPV), as measured or predicted in the ground surrounding a blast. The PPV in the vicinity of a blasthole is strongly influenced by the quantity of the explosive per delay. In general, the existing prediction models give reliable results but fall short of addressing the change in PPV when the charge is decoupled and/or distributed.

Jan 1, 1995

By Richard Brummer, John Hadjigeorgiou, Patrick Andrieux

Some of the major challenges associated with underground mining at depth and/or under high extraction ratios are related to the resulting high stress levels, which can lead to the failure and collapse of the rock mass surrounding the excavations. Sudden and violent failures, which can have severe consequences, represent the highest degree of difficulty in terms of underground personnel exposure, erratic and unpredictable production, ground rehabilitation requirements, possible reserve losses and overall mining costs.

Jan 1, 2012

By Yunnen Chen

This work concerns the removal of zinc(II) and COD by means of sawdust obtained as a by-product from locally used wood. The zinc(II) and COD removal study has been carried out batchwise where the influence of physico-chemical key parameters such as tree species, pH value of solution, temperature and contacting time and dosage of adsorbent have been considered. The maximum percent removal was attained at pH 9 all for Zn(II) and COD after about 60 min. The adsorbent can be effectively desorption using 0.1 M HCl. The experimental results showed that ion exchange maybe the major adsorption mechanisms for binding the divalent metal ions to the sawdust. Sawdust was a potential adsorbent for the removal of Zn(II) from the effluent of electroplating industry.

Jan 1, 2009

By M. J. Gilbey

London Underground is the oldest and one of the deepest Metros in the world. The temperature of the Underground has been increasing over the last 100 years, mainly as a consequence of increases in train service. Further increases in train service are planned in the coming years to meet the predicted growth in passenger demand. Unabated, the additional service will increase temperatures on the Underground. London Underground Limited (LUL) has therefore set up the Cooling the Tube Programme (CTP) to tackle the issues of thermal conditions on the Underground. Some of LUL?s studies and cooling methods have borrowed experience and techniques from the mining industry; some of methods used or proposed may in turn be of interest to the mining community. This paper presents a background into the sources of heat on the Underground network, the manner in which the heat is presently dissipated, the analysis of future temperatures and criterion and a number of means and methods being used or proposed to cool the network in an environmentally sensitive manner.

Jan 1, 2009

Where space is limited, as it is throughout most of the northeastern United States, new construction either takes place high above street level, or below it. In Lower Manhattan, NY both kinds of expansion can be found in abundance. That is good news for the nearly 200 attendees at the George A. Fox Conference, presented by the Underground Construction Association (UCA) of SME at the Graduate Center, City University of New York, on Jan. 30. Among the many projects taking place in Lower Manhattan?s massive trans-formation process, are expansions to the city?s vast underground network of subways and other tunnels. ?New Yorkers either live on the ground or below it,? said keynote speaker Charles J. Maikish while explaining how an attempt to build above street level walkways never caught on in the city. Maikish is the executive director of the Lower Manhattan Construction Command Center. His job is to oversee the $22 billion project that will transform the island by 2010. From the construction of Freedom Tower at the site of the fallen World Trade Center buildings, to the expansion of the Second Avenue Subway, the extension of the East Side Access, No. 7 line, the new trans-Hudson line and numerous waterway tunnel expansions, including City Water Tunnel No. 3, the task Maikish is charged with is a huge one. He is primarily responsible for coordinating the scheduling and staging of the overall rebuilding plan, along with the day-to-day coordination of construction work down-town. He places particular focus on mitigating impacts on the environment and mobility, maintaining and improving access and alleviating congestion of any kind related to construction. At the time of the Fox Conference, there were 59 projects under way in Manhattan. All of those projects need things like concrete and steel delivered to sites in very tight working environments. And some need the equipment in even tighter spaces. ?This is not just about the recovery of Lower Manhat-tan (from the 2001 terrorist attacks) but this is a plan to restore it and to maintain its integrity,? said Maikish. ?I think that is the appropriate response to the terrorist attacks.? When Freedom Tower is completed, it will stand 541 m (1,776 ft) about the skyline. That will be a strong statement to the world about America?s strength. But it is the work that takes place much lower that was of interest to the conference attendees. On this respect, Maikish said Manhattan?s efforts below ground aim to provide relief to the city?s street level congestion and to make sure Manhattan ? already essential to the economy of the United States and the world ? stays current by upgrading the existing telecommunications and technological network while also allowing room for growth in that area.

Jan 1, 2007

By W. E. Coughlin, R. L. Faverty, F. H. Lightner

Introduction The intent of this paper is to present the general strategy and method of implementation to achieve a "fast-track" mine development. The major objectives of a "fast-track" or rapid development schedule are to minimize front-end development expenditures and to realize an early cash flow from operations. The Borealis project of Houston International Minerals Corp. (HIMCO) is used as the working example to illustrate the development schedule. Borealis is a 2.3 kt/d (2,500 stpd) gold-silver heap leach operation near Hawthorne, NV, Pre-Feasibility Planning Proper early planning and identification of priority items were necessary to expedite project progress. On April 1, 1978, HIMCO leased the rights to the Borealis prospect and initiated exploration activities almost immediately. Since Borealis was showing excellent potential for mine development, an effort to clear the way environmentally was initiated during the summer of 1979. With the Borealis properties located within the Toiyabe National Forest, the US Forest Service (USFS) was recognized as the "lead" or respon¬sible agency for addressing the environmental issues. Early scoping of the environmental issues by both HIMCO and the USFS allowed HIMCO to take the initiative and address two potentially critical issues-archaeological and biological. Third party consultants, agreed upon by HIMCO and the USFS, were contracted to conduct archaeological and biological surveys. Desert Research Institute of Reno, NV, provided archaeological services, and JFL & Associates of Boulder, CO, provided biological services. These efforts began in the fall of 1979 and continued through the summer of 1980. Conservative Design Criteria By adoption of conservation design criteria, flowsheets and processing data required for detail engineering were firmly established with a minimum of impact on schedule. On Oct. 21, 1980, HIMCO formally initiated a feasibility study to evaluate the Borealis project. Four organizations were contracted for particular scopes of work: • John T. Boyd Co.: Ore reserve estimation, preliminary mine plan, and mine capital and operating cost estimation. • Bechtel Civil and Minerals: Conceptual engineering, processing capital and operating cost estimation. • Hazen Research Inc.: Metallurgical testing. • Sierra Pacific Power: Cost estimation for power supply. Metallurgical testing and conceptual engineering of both heap and agitation leach flowsheets were investigated concurrently. Numerous economic evaluations were conducted for both heap and agitation leaching at varying production capacities. The results indicated a heap leaching flowsheet treating 454 kt/y (500,000 stpy) yielded the best economics and was compatible with the "fast-track" development goal. Conservative design criteria was established to provide operating flexibility and ensure plant productivities. A summary of major design criteria is presented in Table 1. HIMCO assembled the results of the studies of the various consultants along with internally generated studies to produce the feasibility document. The decision to supply 100% equity by HIMCO rather than arrange project financing help to expedite the project. Cooperation Between HIMCO and Regulatory Agencies With cooperation and mutual trust established between HIMCO and regulatory agencies, the time required for environmental permitting was streamlined as much as practical. To expedite the required construction permits, HIMCO proposed to the USFS that HIMCO fund the total cost of an Environmental Assessment Report (EAR) and that issues be addressed at the technical level of an Environmental Impact Statement (EIS). The previous studies on the critical issues of archaeology and biology provided HIMCO with the information to satisfy the proposed approach. Houston International Minerals and the USFS agreed to have Environmental Research and Technology (ERT) of Fort Collins, CO, prepare a draft EAR for the USFS.

Jan 11, 1983

By Thomas Leonard, Philip R. Berger, Bryan E. Papillon

Bardon Trimount Inc., a large producer of aggregate, crushed stone, and concrete, was experiencing significant public opposition to its five quarries in the Boston area. It was believed by the authors that this opposition could be significantly lessened if the total number of blasts per week were reduced. Although the blasting company at these quarries, Austin Powder Company, contended that this could easily and safely be accomplished by increasing the size of the blasts, regulations precluded this alternative by limiting the total amount of explosives that could be used per blast.

Jan 1, 1996

By Walter R. Curtner

Many, if not most, of today's pollution liability claims are related to events ("occurrences") that happened in the past. This fact creates an opportunity to obtain a large amount of insurance coverage at essentially no cost. Furthermore, in many cases, this insurance coverage is readily available. Scenario #1 For some 15 years, an underground gas tank has had a slow leak. The leak has now been discovered because the gas has contaminated nearby wells. As a result, an expensive $1 million cleanup is required. In addition, a liability suit has been filed for damages due to the contamination of nearby wells. Consequently, legal expenses are being incurred. Are all of these actual and potential costs insured? Obviously, if you have a pollution liability policy in place, the above costs will probably be insured. I say probably because business liability policies are not uniform. But, what if you don't have a pollution liability policy and what if your current general liability policy excludes all pollution liability (as most of them do today)? Under these circumstances, it first appears there is no insurance for this $1 million cleanup and liability suit. But this is probably not the case. You may well have insurance coverage, and you may well have much more insurance coverage than you ever expected. And, the insurance that I'm referring to is already in place. You simply need to find it and learn how to use this insurance - I'm referring to your old policies. In many cases, old liability insurance policies provide coverage for claims made today, because these policies were written on an "occurrence" basis of coverage. In fact, most still are written this way. This means that the insurance policy covers bodily injury or property damage liabilities (as defined in the policy) arising out of' "occurrences" or accidents that happen during the policy period regardless of' when the claim for damages is made. Therefore, for insurance purposes, the key question is: when did the "occurrence" take place? If someone falls and breaks a leg, that is clearly an "occurrence." The broken leg occurrence is, therefore, insured by the liability policy that was in existence at the time of the fall - regardless of when the claim or suit is filed, if ever. However, the answer to this question is seldom an easy one when you are looking at a pollution claim. In our scenario, the tank had a slow leak over 15 years, but property damage was not discovered until now. The question of when the "occurrence" (as defined in the insurance policy) took place has been litigated and continues to be litigated in many courts across the country. But, most often the answer has been that, for insurance purposes, the "occurrence" is the entire period that the tank was leaking (15 years), even though the contamination to the water was not discovered until 1987. This means that the person or company that is insured can potentially use all of its general liability policies (if they are "occurrence" policies, and most were), which were purchased during the 15 years from 1972 until 1987. And, these policies will potentially insure all of the claims and related exposures that arise out of this leaky underground gas tank. Scenario #2 In our first scenario, the claims and expenses were insured by past general liability policies because the claims arose out of events in the past, which, in turn, caused damage. Let's look at another example. In this scenario, Company XYZ has received a request to help clean up a landfill site because 10 years ago, XYZ dumped some toxic substances at the site, which was totally legal at the time. XYZ has not dumped anything at the site since this time. Nevertheless, XYZ is now being required to contribute $2 million to the cleanup of this site. In this scenario, if you had purchased "occurrence" general liability policies 10 years ago, these 1977 policies would (potentially) apply to the current $2 million cleanup claim. And, the reason is that the "occurrence" leading to the 1987 claim took place in 1977.

Jan 10, 1987

By Frank P. Frandina, Michael J. Loehr, Paul E. Gabryszak

The Heartland Corridor Clearance Improvement Project is part of a regional Public-Private initiative to allow double stack container trains a direct route from the Port of Norfolk through Virginia, West Virginia, Eastern Kentucky and into Central Ohio. In the Preliminary Engineering stage, 30 existing tunnels were assessed and 28 were found to need clearance improvements to allow the use of double stack trains. Alternative tunnel enlargement methods were developed to achieve the desired clearance improvements, while maintaining structural integrity and minimizing disruption to train traffic. This paper summarizes the geometric and condition investigations of the existing tunnels, as well as describes the preferred methodologies to achieve the desired clearance. The clearance improvements will be implemented beginning in the summer of 2007.

Jan 1, 2007

Discussion of the paper of Frederick Laist, presented at the Butte meeting, August, 1913, and printed in Bulletin No. 79, July, 1913, pp. 1147 to 1162. J. C. DICK, Salt Lake City, Utah :-I would like to ask Mr. Laist why a 10 per cent. salt solution was used. MR. LAIST :-The reason for using salt in the solution is to get .the sulphur. The solution of dilute sulphuric acid has no solvent action on the sulphur even after roasting, and the addition of the salt is made primarily to dissolve the sulphur chlorides. MR. DICK:-I would like to ask also if you made any experiments as to grinding fine your calcines, rather than leaving the coarse material. MR. LAIST :-We have not made any experiments along those lines except in the laboratory, but the objections which we have to grinding are that the difficulties of roasting are very much greater when roasting finely ground material than when roasting coarse material, and the difficulties of leaching are somewhat increased; the percolating system is simpler and easier to manipulate, particularly when acid solutions are used, so that we prefer from our experience not to grind. STUART CROASDALE,* Denver, Colo. (communication to -the Secretary +) :-In order to meet the conditions involved in his ore-treatment problem, Mr. Laist has developed a very interesting and apparently successful metallurgical hybrid which he calls the oxychloridizing roast. The lower floors of the MacDougall furnaces are made to accomplish what used to be done on the " cooling floor" in the old days of salt roasting and " hypo " or brine leaching of silver ores.

Jan 11, 1913

By de Bruin J H

A method new to Australia was used for sinking a vertical shaft at Broken Hill in the development of Pasminco Southern Operations No 5 Ventilation Shaft. The 6 m diameter shaft of 820 m depth was planned with a construction method which allowed access for ground support as sinking proceeded by mechanical excavation.The vertical shaft boring machine, known as the V-Mole, was originally developed in West Germany. The machine operates in a manner similar to a full face TBM but vertically and the cuttings drop down a previously constructed raise. The raise is subject to stringent tolerance on verticality and must remain stable for the duration of reaming.

Jan 1, 1993

By M. F. Trice

Pyrophyllite is a hydrous aluminum silicate (A1²Si4O10(OH)²)1 that, occurs in both the foliated and the massive forms. The foliated variety resembles talc in that it has a greasy feel, a pearly luster, perfect basal cleavage, and usually is white, although in some deposits apple green, gray, brown, russet, and nearly black specimens may be found. The massive deposits of pyrophyllite yield pearl gray to light tan aggregates, some of which are so friable that they may be crushed with the hands into a fine gritty powder. Frequently specimens of the massive variety are studded with crystals of radial structure. The mineral has a specific gravity of about 2.7 and a hardness of 1 on Mohs' scale.' The chemical composition of commercial pyrophyllite reflects the mineralogy of the deposits, which, according to Stuckey12 contain pyrophyllite and quartz, together with chloritoid, sericite, and a few other minerals of negligible importance. The latter, he says, ('are noticed in but small quantities to the extent they might occur as accessory constituents of an igneous rock or as products of regional metamorphism or weathering. . . . Quartz is abundant everywhere except in the very best grades of pyrophyllite." Analyses of specimens from several deposits are listed in Table 1, showing that the silica content varies from 57 to 73 per cent and the alumina from 22 to 33 per cent. Oxides of iron and the alkaline metals are collectively present, with one exception, to an extent of about 1 to 1.5 per cent. Sources At present, North Carolina is the only commercial source of pyrophyllite, although the mineral has been found in small quantities in many parts of the world. The North Carolina deposits are in the "Carolina Slate Belt," which traverses the center of the state in a southwesterly direction. This belt varies from 8 to 50 miles in width. Two major deposits of pyrophyllite lie along its eastern boundary, in what is known as the Deep

Jan 1, 1942

By A. A. Smith, J. S. Smart

THe elements silver, cadmium, tin, antimony and tellurium either are found as impurities in commercial coppers or are intentionally added to produce coppers for special uses. When present in small quantities, each of these metals exerts a significant effect on the properties of copper, but despite considerable experience and investigation much remains to be learned about their specific behavior. The presence of extraneous elements, particularly oxygen, complicates the study of individual additions of impurities in the range o to 0.05 per cent, and the use of high-purity copper has been found extremely helpful in circumventing these difficulties. It has also been found that individual behavior can be satisfactorilv determined from measurements of two commercially important properties, conductivity and softening temperature, according to methods that have been described previously.1,2 Data of this type, obtained in the course of a general investigation of the effects of impurities on the properties of both oxygen-bearing 2nd oxygen-free copper are presented herewith. All samples except those containing cadmium were prepared as 3/8-in. continuously cast oxygen-free rod from pure copper and weighed amounts of a similarly synthesized master alloy. Composition was checked by chemical methods, which in every case verified the calculated analyses. Test wires were cold-drawn one B, and S. number per pass on a string-up machine using four 30-min. 600°C. anneals at 0.3125, 0.257, 0.204 and 0.162 in. and a final cold reduction of 75 per cent to 0.081 in. Some oxygen-bearing samples were produced directly from the 3/8-in. oxygen-free rods by diffusion from a surface scale at 850°C. and drawn to size as listed above, but most of the alloys were remelted in pure graphite and cast through air into a I-in. round mold. The slugs were then hot-rolled to 5/16 in., drawn to 0.162 in., annealed as listed above, and drawn to 0.081 inch. Conductivity wires were annealed for I hr. at 100°C. intervals between 300' and 800°F., using a hydrogen atmosphere for oxygen-free samples and purified nitrogen for the oxygen-bearing type. All samples were quenched from the annealing temperature in 10 per cent H²S04 and conductivity was measured on a Hoopes bridge that had been checked against a Kelvin bridge. The softening temperatures represent the half-hard stage of the annealing curve as determined by a standard procedure.' Effect of Silver Numerous excellent studies of the argentiferous coppers are found in the literature, and these have been adequately

Jan 1, 1943

The coal resources of the Singleton- Muswellbrook area of New South Wales are of major importance to Australia, and are likely to play a significant role in meeting the expanding demands for energy in many countries of the world. Coal resources of 45 thousand million tonnes of which 15 thousand million tonnes lie at a depth of less than 200m have been estimated. The history of coal mining in the area commenced in the mid 1800's and has been one of fluctuations in production but of rapid expansion in more recent years. It is destined to become the largest coal producing area in New South Wales. Coal is being won from the area by strip mining, open pit mining and by underground means. The techniques involved are described. The area is well endowed with infra- structure such as modern towns, railways, road- ways and access to port facilities. Production of both coking coal and steaming coal is expected to rise significantly within the next 25 years. A large proportion of the State's anticipated increased production to between 117 and 177 million tonnes by the year 2000 is likely to come from this area.

Jan 1, 1979

Pongkor Gold Mines is one of seven units of production owned by PT Aneka Tambang (State owned mining company). The mine is located in the western part of Java Island, Indonesia. It is in the Bogor District and approximately 110 kilometres to the south of capital Jakarta. It is located in very steep hilly terrain intersected by many river valleys and the mine site is approximately 500 metres above mean sea level (see Figures 1 and 2 - Mine location map and picture)

Jan 1, 1997

By Thomas E. Leontis

INTRODUCTION THE importance of magnesium alloys in the manufacture of aircraft engines has been realized for many years. A concentrated effort has been exerted in the laboratories of the Dow Chemical Co. to develop magnesium-base alloys with improved properties at elevated temperatures whereby greater advantage can be taken of the inherent lightness of these materials. In an earlier publication,1 attention was called to the superior tensile properties and resistance to creep of cerium-containing magnesium alloys at temperatures up to 700°F. More recently, additional data on magnesium-cerium alloys have been furnished by Murphy and Payne.2 The present paper deals with the mechanical properties of sand-cast magnesium alloys containing zinc, at temperatures up to 500°F. The study includes binary Mg-Zn† alloys containing up to 10 pct zinc and several ternary and some polynary alloys based on the Mg-1Zn,†Mg-3Zn, Mg-4.4Zn, Mg-6Zn, and Mg-10Zn binaries. The compositional variation in the tensile properties, hardness, and creep at room and elevated temperatures, and in the electrical conductivity at room temperature has been determined. The results of these tests show that many zinc-containing magnesium alloys exhibit resistance to creep at elevated temperatures significantly higher than that of present commercial magnesium alloys, but lower than that of alloys of the magnesium-cerium type. In addition, they have high tensile properties at room and elevated temperatures and high conductivity. This combination of mechanical properties and conductivity indicates that these alloys should be given serious consideration for commercial applications involving exposure to temperatures higher than those to which present commercial magnesium alloys can be taken safely. LITERATURE The properties of sand-cast magnesium alloys containing zinc as a principal alloying element have not been investigated very extensively, especially at elevated temperatures. The following remarks, which are confined to sand-cast alloys, will serve as a summary of the most important references on this phase of magnesium metallurgy. The first recorded determination of the tensile strength of binary Mg-Zn alloys as a function of zinc content was reported by Aitchison.3 Similar studies, including the measurement of elongation and hardness, have been performed by Gann and Winston,4 Dumas and Rockaert,5 Haughton and Prytherch,6 and by Spitaler, the last being reported by Beck.7 A slight superiority in the tensile strength of chillcast Mg + 8 Zn alloy over the sand-cast alloy was noted by Maybrey 8 That alloys of magnesium containing 5 to 12 pct zinc

Jan 1, 1948

The reduction in the number and duration of machinery and equipment failures is an important source of economical efficiency enhancement in the Polish coal mining industry.Non-dismantling methods have been thus developed to evaluate the technical state of machines. Among these viroacoustical methods are the most effectively employed. Two-directional organisation of the testing can be chosen, such as periodical and continuous inspection. The monitoring methods for ball bearing, rope tension uniformity, longwall shearers, main fans and shafts installations etc. Instrumentation for monitoring measurements are either of intrinsically - safe or explosion - proof construction, which enables using them in a gas-hazard atmosphere. The development of these procedures has led to the trials to insert the diagnostic methods into the organisational scheme of a coal mine.

Jan 1, 1991

By Bishop D. J

The Imperial Smelting Process for the simultaneous production of zinc and lead is probably regarded by the ecologist as a necessary evil with the benefits of its products marginally outweighing the adverse effects of its operation. The purpose of the paper is to examine the environmental impact of the process and to provide information which will demonstrate that the process has considerable indirect environmental benefits and that success is being achieved in reducing direct pollution of the environment by the process. About 12 per cent of the world's zinc and seven per cent of its lead is produced by the process. This proportion will increase with the construction of a new smelter in China. After a brief description of the process the paper considers one of its principal advantages, its ability to treat bulk concentrates. The production of these at the mine can have a number of environmental benefits. Less comminution may be required to separate the metals from the gangue than is needed to separate them from each other; recoveries can be improved in flotation resulting in cleaner tailings dams, less power demand and reduced consumption of potentially hazardous reagents. Simplification of mining and above ground ore handling may also give significant benefits . The process is a considerable consumer of secondary materials such as galvanisers' ashes, copper smelter dusts and materials containing zinc and lead derived from steel plant dusts. The majority of these materials are fed to the blast furnace after hot briquetting. The consumption of secondary materials is a considerable environmental benefit since otherwise they would require to be dumped in secure land-fill sites. The operation of the process itself continues to be subjected to increasingly stringent environmental standards of which examples are provided. Details are provided of lead emissions at Avonmouth showing considerable success in reducing these while increasing production. The slag from the process continues to find many useful applications.

Jan 1, 1993