Search Documents

By H. W. Russell, Paul D. MILLER

IT is known that austenitic chromium-nickel steels that have free carbide in the grain boundaries are subject to intergranular corrosion. It is difficult to detect such a susceptible condition in a fabricated article because present test methods require a sample section for examination and in most cases this is difficult to obtain. The question of the nature and prevention of intergranular corrosion in austenitic stainless steels have been ably discussed by Bain and co-workers1-3 and by other investigators.4-10 The present methods of study subject samples to corrosive conditions in such reagents as the Strauss solution, a. mixture of copper sulphate and sulphuric acid. Such tests usually require at least 72 hr. to run. Various methods of measuring the degree of sensitization have been employed, such as the measurement of electrical resistivity, magnetic measurements, measurement of the degree of cracking produced on bending over a mandrel, and microscopic studies. The detection of carbides at the grain boundaries by metallographic polishing and etching methods is tedious and requires a skilled operator. A recent report on such methods of carbide detection is given by the American Society for Testing Materials Subcommittee VI of Committee A-10 11 and by Arness.12 The present investigation was undertaken to develop a simple test procedure for detecting carbide precipitation or susceptibility to intergranular corrosion. The test is designed for use in the plant and for the testing of fabricated structures. Carbide precipitation, the factor leading to susceptibility to corrosion, is produced by heating the alloy in the temperature range 800° to 1600°F., as in welding, in improper annealing or in service where such temperatures are met. The connection between such precipitation and susceptibility to corrosion has been thoroughly discussed, as has been the use of stabilizing addition elements to prevent precipitation. EXPERIMENTAL METHOD A small area of the steel under test is subjected to an anodic treatment in a cell that can be clamped onto a sample or an actual structure. The cell and electrical circuit used are illustrated in Fig. I. The cell C is lead, joined to the steel plate D and insulated from it by a short piece of rubber tubing E. The cell is forced tightly against the steel plate by a spring or clamping device. The seal formed by the rubber against the steel plate is sufficient to retain the liquid bath inside the cell. The spot treated can be made any shape desired, depending on the shape of the rubber gasket. The cell illustrated polishes a circular spot about 3/8-in. diameter. The bath consists of 60 per cent (by weight) sulphuric acid to which is added 5 ml. per liter of Glycyrrhiza extract (U.S.P.). The cell requires about 2 to 2.5

Jan 1, 1941

By Ralph W. M. Lai, D. W. Fuerstenau

This paper presents the results of a study of the principles which control the distribution of ultrafine particles between an oil phase and an aqueous phase. Alkyl sulfonates were used to control the wettability of fine alumina particles and to stabilize the water-isooctane emulsion system in the extraction process. The effects of sulfonate chain length, sulfonate adsorption, pH, and oil-water ratio on the recovery of solids in the oil phase were investigated. Higher extraction was found under conditions which yield higher hydrophobicity and large interfacial area of the oil-water emulsion. Today there is considerable interest in developing methods for the recovery of fine particles from disseminated ores. One such method might be the extraction of fine particulate solids from aqueous suspensions into an oil phase, and one example of a successful industrial process based on oil-water distribution phenomena is the emulsion flotation process used in concentrating manganese ore.' The oil agglomeration process of Farnand, Smith, and Puddington has been suggested for concentrating tin ore. Patents 3-4 for oil flotation processes extend back to that of William Haynes in 1860. The basis of all these processes is directly related to the stabilization of emulsions with solid particles. The first extensive study of oil-water emulsions stabilized by finely divided solids was made by Pickering. Later, Briggs,6 weston, 7 Chessman and King,8 and Leja and Schulman9 experimentally demonstrated how solid particles control water-oil and oil-water systems. Hildebrand10 suggested that fine particles can stabilize an emulsion because the fine particles are partially wettable by both oil and water, that is, that the contact angle must be finite. Takakuwa and Takamori 11 recently applied emulsion inversion to the study of collector adsorption in flotation systems. At the Royal School of Mines, Shergold and Mellgren12 are currently carrying out a comprehensive study of the extraction of fine particles into an organic liquid phase. In the present study of the liquid extraction or oil flotation of ultrafine particles, the recovery of hydro-philic alumina particles of 0.1-µ average diameter was determined after separating an isooctane-water mixture (emulsion) into its two phases. Alkyl sulfonates of different chain lengths were used to change the wettability of the alumina and to effect emulsifi-cation of the oil-water mixture. The effects of the oil-water volume ratio, sulfonate adsorption, and pH on the recovery of the fine particles were investigated. Since the surface charge on an oxide such as alumina is determined by the adsorption or interaction of H+ and OH- with the surface, pH control is extremely important. Furthermore, since the zero point of charge (zpc) of alumina13-14 occurs at pH 9 to 9.4, major adsorption effects with anionic collectors in these systems will occur below pH 9. The results of the foregoing investigation are discussed in terms of the recovery of the fine particles, the oil-water ratio, contact angles, surface tension, the adsorption of sulfonate onto the solid surface, and the emulsifica-tion of oil. MATERIALS AND EXPERIMENTAL METHODS Materials: The particulate solid used in all the experiments was Linde "A" alumina, a high-purity, readily available form of a-alumina. The surface area of the alumina, as evaluated from measurements of stearic acid adsorption from benzene, was 14.5 sq m per gm, based on a value of 20.5 sq Å for the cross-sectional area of stearic acid.13 All aqueous solutions were prepared from triply distilled conductivity water. Other materials included high-purity crystals of sodium alkyl sulfonates, isooctane, and, for pH adjustments, reagent grade hydrochloric acid and sodium hydroxide-Because sulfonic acids are strong acids, they are

Jan 1, 1969

By A. L. Titchener, M. B. Bever

The stored energy of cold work was investigated in drawn gold-silver wires by tin-solution calorimetry as a function of strain, strain rate, initial grain size, and temperature of defornation. The energy expended in the deformation process was measured. Hardness was also measured and was correlated with the stored energy as a function of strain and strain rate. Mechanisms of energy storage are discussed. THE variables which determine the amount of energy stored in a metal during cold work are of two kinds: those involving the metal and its condition and those involving the process of deformation. For example, the stored energy differs between one metal and another and between different degrees of purity of a single metal. It also depends on the nature of the deformation process and particularly the extent, rate, and temperature of deformation. Most investigators have reported the stored energy as a function of strain (or some similar geometric parameter) or of the energy expended during deformation. In general the stored energy increases with strain, rapidly at first, but more slowly at large strains until a saturation level is reached. Information about the effects of other variables, however, is limited. Some data are available on the dependence of the stored energy on the purity of a metal1 and on the composition of

Jan 1, 1960

By Joseph Fry, Ralph H. Espach

In the spring of 1943, when it was evident that the Tensleep bandstone in the Elk Basin Field, Wyoming and Montana, held a large reserve of petroleum, Bureau of Mines engineers obtained samples of oil from the bottom of nine wells and analyzed them for such physical characteristics as the volumes. of gas in solution. saturation pressures or bubble points, shrinkage in volume caused by the release of gas from solution, expansion of the oil with decrease in pressure, and other related properties. The composition of the gas in solution in the oil was studied. The pressures and temperatures existing in the reservoir and the productivity characteristics of the oil wells were determined. The data obtained indicate that the oil in the Tensleep Reservoir of the Elk Basin Field has unusually varying physiral characteristics, such as a saturation pressure of 1,250 psia and 490 cu ft of gas in solultion in a barrel of oil at the crest of the structure and a saturation pressure of 530 psia and 134 cu ft of gas in solution in a barrel of oil low on the flanks. The hydrogen sulfide content of the gas in solution in the oil varies from 18 per cent for oil on the crest to 5 per cent for oil low on the flanks of the structure. Of even greater significance is the fact that these and other variable characteristics of the reservoir oil are related to the position of the oil in the structure. Many geologists and petroleum engineers have considered that all the oil in a petroleum reservoir has rather uniform physical characteristics and that equilibrium conditions prevailed in all underground accumulations of oil and gas; that such is not always so is borne out by the results of the study by the writers. INTRODUCTION The Rocky Mountain region is one in which may be found striking examples of the unusual in oil and gas accumulations, as is evident from the following: The high helium content (7.6 per cent) of the gas in the Ouray-Leadville limestone sequence in the Rattlesnake Field, New Mexico, and gases of similar helium content in other fields; 50" to 55' API gravity distillate in solution in carbon dioxide gas and recoverable through retrograde condensation, in the North McCallum Field, Colorado; the occurrence of gas, oil, or both in closely related structures contrary to the usual concepts of gravimetric segregation: the accumulation of gas and/or oil in structures closely related to other structures that apparently are more favorable but do not contain oil or gas accumulations; the high hydrogen sulfide content (as high as 42 per cent) of the gas associated with oil in some fields in the Big Horn Basin, Wyoming; and the wide range of fluid chararteristics found in the Elk Basin reservoir. Elk Basin, an interesting old oil field that has been producing oil from the Frontier formation since 1915, is situated in a highly eroded basin resulting from the erosion of the crest of an anticline and some of the underlying softer shales. The field came back into national prominence during 1943 when it became known that it was the largest single reserve of new oil discovered in the United States that year. The Tensleep sandstone was found to contain oil in November. 1942, when a well drilled to a depth of 4,538 ft (44 ft into the Tensleep sandstone) flowed oil at the rate of 2,500 B/D. By the end of 1949, 137 oil-producing wells and five dry holes had been drilled, and approximately 32 million bbl of oil had been produced. Approximately 6,000 acres may be considered productive of oil in the Tensleep Reservoir, and estimates of the oil that will be produced average 200 million bbl. The Tensleep Reservoir has further interest because it ha-greater closure than any oil field in the Rocky Mountain region; the closure of the Elk Basin anticline is variously estimated at 5.000 to 10,000 ft. of which the top 2.00 ft of the structure contained oil. SUBSURFACE OIL SAMPLING Fig. 1 is a structural map of the Elk Basin Tensleep Reservoir, on which the nine wells used in this study and the numbers correvponding to the well designations hereafter referred to are shown. Wells 1. 2, 3, 4, and 8 were tested and sampled during October and November. 1943. and Wells 5, 6. 7, and 9 during June and July, 1944. An electromagnetic type sampler developed by the Bureau of Mines and described by Grandone and Cook' was used in obtaining the subsurface oil samples. As the wells were tubed nearly to bottom, the sampler was run as far as possible in the tubing hut never below the top perforations. The following procedure was used in testing and sampling the wells: A well was shut in for at least three days, after

Jan 1, 1951

By F. D. Rosenthal, F. J. Dunkerley, G. J. Mills

Activities, free energies, and heats and entropies of mixing of liquid Pb-Zn alloys have been obtained by the electrode-potential method between 400° and 650°C. The large positive deviations observed from Raoult's law are in agreement with the phase diagram, which indicates a wide immiscibility field. A vapor-pressure method was used to extend the activity measurements to 900°C, allowing the maximum of the immiscibility gap to be estimated by thermodynamic calculation. Data on the mono-tectic and eutectic points compare favorably with previously existing work. SEVERAL long-standing methods have been in use for the study of phase diagrams from measurement of the activities of the component metals.' The use of thermodynamic analysis for interpreting equilibria data is comparatively recent, however. Such analysis is usually undertaken by first evaluating the principal thermodynamic functions as, for example, the enthalpy, entropy, and free energy of the alloy constituents. These, in turn, quite often can be correlated with the interatomic potential energies and atomistics of the system, from which a clearer understanding of the causes leading to deviations from ideal behavior is gained. The present study of liquid Pb-Zn alloys is concerned with a determination of these quantities by electrode-potential and vapor-pressure measurements, using these values in calculations involving phase equilibria and to obtain a theoretical insight into an alloy system exhibiting strong positive deviations from ideal metallic solution. A considerable portion of the previously reported work is based on thermal analysis. Supplemented by optical studies of solid alloys, these techniques have revealed the essential nature of the immiscible mixtures that are formed. It is difficult, however, using the phase-

Jan 1, 1959

By J. T. Raleigh, D. L. Flock

This study investigated the nature of formation plugging with bacteria and attempted to relate its characteristics to physical rock properties. Fifteen core samples of four specific formation types were defined and plugged using a commonly occurring, uniform sized dead bacteria, Bacillus subtilis. Two of the formation types were fairly uniform-grained sandstones and two were heterogeneous carbonates. The injection rate and concentration of solids in the brine were held constant during the test runs. The pore geometry factor G was a significant petro-physical rock characteristic for correlation with depth of plugging, but lacked importance as a parameter for rate of plugging. Although the G factor may not completely describe porous rock geometry for plugging predictions, for reservoirs with multi-pore systems, there is evidence that the pore geometry factor might form a basis for establishing injection water specification in more llornogeneous reservoirs with only primary porosity development. INTRODUCTION GENERAL PURPOSE Injecting water into oil-bearing formations to increase recovery is common practice in the petroleum industry. One of the most serious operational problems involved with water injection wells is the tendency of the porous rock immediately adjacent to the injection wellbore to plug partially. This results in increased injection pressures and/or a decrease in the rate of injection. This plugging in injection wells can result from a number of causes, including bacteria contained in the injected water.1 The purpose of this work was to investigate the nature of injection plugging with bacteria and to attempt to relate its characteristics to physical rock properties. Many variables exist in research of this type, so, to reduce them, injection rate and concentration of bacteria in brine were held constant. The bacteria used for plugging was a uniform-sized, dead bacteria, Bacillus subtilis, a micro-organism commonly found in water, air and soils. Four specific porous rock types were plugged—two consolidated sandstones and two heterogeneous carbonates. The experimental work involved two distinct phases. The first concerned determining the physical rock properties and the second was the experimental work of actually plugging the selected core samples. PORE GEOMETRY FACTOR Capillary pressure is necessary to displace a wetting fluid from a capillary opening with a nonwetting fluid. The factors which govern capillary pressure are the surface or interfacial tension of the fluids involved, the system wettability and the equivalent pore radius. Thus: P,= 2ucososrd..........(1) Thomeer used the idea that the location and shape of the capillary pressure curve reflect characteristics of the pore structure of any porous media sample.' He presented the mathematical description of capillary pressure curves and of indicated differences in pore geometry of samples. where G = pore geometry factor PC = capillary pressure Pi = displacement pressure (V,)p, = fractional bulk volume occupied by the displacing fluid at any capillary pressure (V,), = fractional bulk volume occupied by the displacing fluid at infinite pressure or total interconnected pore volumes. The shape of the curve is defined by the pore geometry factor G. The curve shape is related directly to the sorting and interconnection of the pores of the sample. The location of an infinite number of curves can be defined by the same asymptotes. However, these curves differ in shape, each curve being described by a specific value of G. Thus, the description of a curve is unique when, in addition to the position of its asymptotes, its shape is defined. These curves can be used graphically to determine the characteristic parameters of any arbitrarily located curve. Those parameters that can be approximated from any capillary pressure curve are: (1) total interconnected pore volume, represented by (V,),- ; (2) extrapolated displacement pressure, the abscissa axis; and (3) pore geometry factor, by the curve shape. PROPERTIES OF BRINE AND BACTERIA The fluid used throughout this study was an aqueous solution of sodium chloride, 25,000 ppm by weight. The addition of salt to fresh water was intended to eliminate clay swelling in the sandstone cores and to retard leaching in the limestone cores. The viscosity of the brine solution at 100F, the temp-

Jan 1, 1966

By R. E. Cook

This paper presents results of a study to determine to what extent errors in estimated free gas saturation affect the results of static pressure calculations from build-up curves in two-phase systems. Use is made of the method of pressure build-up curve analysis developed by Miller, Dyes and Hutchinson1 , with modifications for two-phase flow advanced by Perrine2. Cornhined fluid compressibility of gas-oil mixtures is included, with special attention given to the discontinuity that occurs in fluid compressibility at the saturation pressure and its effect on static pressure calculations from build-up curves. The sensitivity of static pressure calculations to errors in gas saturation is considered over wide ranges of formation and fluid properties and reservoir pressure conditions. It is concluded from this study that for analyses of two-phase pressure build-up curves (I) the use of under-saturated crude compressibility data, even when producing GOR's are at or near solution values, will result in very significant negative errors in calculated static pressrrre, and (2) except for large values of buildup curve .slope and/or very low crude gravities, rather large errors in calculated gas saturation can he tolerated without .significant effect on calculated static pressures. The conc1usions arc qualified as referring only to the effects of gas saturation and excludc possible errors in the nuumerous other factors that enter into the ancllysis of pressure build-up curves. INTRODUCTION As part of the analysis of basic data for several major Eocene reservoirs in the Bolivar Coastal field (Western Venezuela), it was necessary to analyze a large number of pressure build-up curves for oil permeability and static reservoir pressure. From performance data it became apparent that gravity segregation is very active in these reservoirs. As a result of this performance it was recognized that the free gas saturation within the oil leg of the reservoirs would be small but would be subject to certain errors in calculation due to the inaccuracy of relative permeability data in the low gas saturation region. Since all of the various methods of build-up curve analysis were originally derived for sin- gle-phase, constant compressibility systems, and since the presence of a small but rather indeterminate gas saturation would greatly affect the reservoir fluid compressibility, a study was undertaken to investigate the effect of gas saturation on the results of two-phase pressure build-up analyses. TWO-PHASE BUILD-UP CURVE ANALYSIS The method of analysis used in this investigation is basically that originally developed by Miller, Dyes and Hutchinson1, with modifications for two-phase flow advanced by Perrine2. Miller, et al, showed that the original equation for single-phase permeability away from the well bore, held for two-phase flow except that the calculated permeability is the effective permeability to oil away from the wellbore. This finding was acknowledged by Per-rine, who also presented the equation for effective gas permeability* as Since Eqs. 1 and 2 contain no terms influenced by fluid compressibility, no distinct problem should develop in calculating permeability from two-phase build-up curves. In regard to the calculation of static reservoir pressure from build-up curves in single-phase systems, the modified Miller, et al, method as presented by Perrine is briefly as follows. 1. From build-up curve data, PVT data for the reservoir fluid and the well spacing and sand thickness, calculate the climensionless shut-in time corresponding to the highest value of actual shut-in time (t, hrs) on the straight-line portion of a semi-log build-up curve. Dimenrsionless shut-in time is related to actual shut-in time by the relation, t- 0.000264 kt 2. From a graph of dimension less shut-in time vs dimensionless pressure difference (Fig. 1 1 ) find the value of dimensionless pressure difference corresponding to the value of 7 calculated under (1) above. Dimen-

By S. N. Singh, M. C. Flemings

Results are presented of a detailed study on the combined influences of ingot dendrite am spacing and thermomechanical treatments on the structure and solution kinetics of high --purity cast and worked 7075 alloy. Solution kinetics were found to depend sensitively on ingot dendrite am spacing and on details of therrnomechanical processing, including amount of reduction and extent of&apos; solution treatment before reduction. An approximate analysis is given for rate of solution of nonequilibrium second phase in the cast and worked structres; results of the analysis are compared with experiment. MICROSEGREGATION in high strength aluminum alloys manifests itself as "coring" (composition differences within the primary aluminum-rich phase), and as interdendritic second phase. The mechanism of formation of the microsegregation is understood, and approximate prediction of the amount of second phase is possible for simple binary systems.1,2 When alloy elements or impurities are present in amounts less than their solid solubility at solution temperature, any phases forming from these elements are termed "nonequilibrium" and can be dissolved by appropriate solution treatment. The rate at which the nonequilibrium phases are removed depends sensitively on their spacing (dendrite arm spacing in the cast material, or band spacing in wrought material). When alloy elements or impurities are present in amounts in excess of their solubility at the solution temperature, second phase particles form an "equilibrium" second phase that does not dissolve in heat treatment and may, in fact, coarsen in such treatment. Usual commercial, high strength, wrought aluminum alloys contain nonequilibrium second phases that were not fully dissolved during ingot processing. They also contain equilibrium second phases resulting from impurities present in amounts greater than their solubility. As has been shown by Antes, Lipson, and Rosenthal,3 and will be demonstrated further in a subsequent paper by the authors,4 significant improvements in mechanical properties of high strength alloys can be achieved by reduction or elimination of these second phases. Methods of elimination are 1) to employ high purity materials to minimize amounts of equilibrium second phase, and 2) to employ suitable thermomechanical processing techniques to fully eliminate nonequilibrium second phases. Work reported herein comprises a study of selected thermomechani- cal processing treatments, and of their influence on solution kinetics of wrought high purity 7075 alloy. EXPERIMENTAL PROCEDURE Melting and Casting. The bulk of the work reported was performed on a single ingot of high purity 7075 alloy. The ingot was 4 in. by 4 in. by 8 in. high, uni-directionally solidified following a procedure previously described.5 The mold was heated to 1350°F before pouring the melt. The bottom chill was carbon coated stainless steel. Water was circulated through the chill after the melt was poured. The 7075 alloy was prepared from high purity virgin material (aluminum, zinc, magnesium) and from master alloys (Al-50 pct Cu, A1-15 pct Cr, A1-5 pct Ti). Final measured melt composition (wt pct) was: Zn Mg Cu Cr Ti Fe Si Al 5.70 2.28 1.35 0.18 0.15 <0.002 <0.012 bal Melting was done in a silicon carbide crucible; all tools were coated with zircon wash to minimize iron contamination; degassing was by bubbling chlorine through the melt. che-rmomechanical Treatments. Detailed studies were made on material taken from a location approximately 13 in. from the chill and 51/2 in. from the chill (i.e., from 1 in. thick slices taken between 1 and 2 in. from the chill and between 5 and 6 in. from the chill). Solution treatment was done at 860°F in an air-circulating furnace with a "bottom drop" arrangement to achieve minimum delay time between solution treatment and quench. Samples solution treated in this way were 2 in. by 2 in. by 1 in. Temperature of the quench water was approximately 10°C. Mechanical reduction was by cold rolling. Samples 11/2 and 51/2 in. from the chill were treated for 12 and 24 hr, respectively, before cold rolling. Reduction by cold rolling was then 4/1, 16/1, and 35/1. In each case, several intermediate anneals (1/2 hr at 860°F) were used to permit reaching the final thickness without cracking; two such anneals were used for the 4/1 reduction, five for 16/1, and six for 35/1. After working, materials were again solution treated for various lengths of time from 0 to 48 hr and quenched in water. Structural Measurements. Secondary dendrite arm spacings were measured using procedures previously described.&apos; For each measurement reported, five photomicrographs were first made at X75. Measurements were made of dendrite arm spacings in at least 20 different grains (grain structure was equiaxed). Grain size measurements were made by running a number of random traverses across photomicrographs of the samples and obtaining the mean lineal intercept. Measurement of the volume percent of second phase and porosity was done by quantitative metallography. A two-dimensional systematic point count was used

Jan 1, 1970

By K. G. Wikle, W. W. Beaver

The factors which control the rate of dissolution of pure gold in cyanide solution were studied both directly and through measurement of solution the current-potential curves for the anodic and cathodic portions of the reaction. The mechanism of dissolution is probably electrochemical the reaction in nature, and the rate is determined by the rate of diffusion of dissolved oxygen or cyanide to the gold surface, depending on their relative concentrations. The significance of the results and the effects of impurities are considered. ALTHOUGH the dissolution of gold in aerated cyanide solutions has been used as an industrial process for treatment of gold ores since the late nineteenth century, the factors which determine the rate of the reaction have never been identified unambiguously. Studies of the rate of dissolution by Maclaurin,1 White,2 Christy,3 Beyers,4 Thompson,6 and others are contradictory in their conclusions; some claiming that diffusion of the reactants to the gold. surface controls the rate, and others that the chemical reaction is inherently slow and related to high activation energy for the reaction. Christy3 and &apos;Thompson" both suggest that the reaction is electrochemical in nature and that the dissolution of gold proceeds at local anodic regions while the oxygen is reduced at cathodic regions on the gold surface. Although their studies are ingenious and do indicate an electrochemical reaction under the conditions of study, their experiments were of limited nature and failed to identify the rate-controlling process in the system. The importance from an industrial viewpoint of a knowledge of the mechanism and rate-controlling factors in gold dissolution can be illustrated as follows: If the rate is controlled by a slow chemical reaction rather than by diffusion of the reactants, then an increased temperature should have a marked accelerating effect; agitation of the slurry should have no effect on rate: and increased concentration of reactants should cause acceleration of the rate. If the rate is controlled by the diffusion of one or the other of the reactants to the gold surface, then increased agitation should increase the rate; increased temperature will increase the rate, but not as much as for the case of a slow chemical reaction; increased concentration of the reactant which is diffusion limited will increase the rate; and the concentration of other reactants should be without effect on the rate. It may be concluded that for design of a commercial process for gold leaching, the rate-controlling factors of the reaction should be understood so that an intelligent choice of the conditions of agitation, temperature, and reactant concentration may be made. The experiments described here lead to the unambiguous conclusion that in a system of pure gold and a pure aerated cyanide solution the rate of dissolution is controlled either by the rate of diffusion of dissolved oxygen or cyanide to the gold surface, depending on the relative concentrations of each. There is also ample, but not conclusive, evidence that the mechanism of the reaction is identical to that of electrochemical corrosion. The practical significance of these conclusions will be discussed later in the paper. Experimental The experimental method used in this work was to employ an electrolytic cell which performed the overall gold-dissolution reaction, and to study the anodic and cathodic reactions of this cell as to their nature and the rate-controlling factors. Simple experiments on the rate of dissolution and the potential of the dissolving specimen also were performed under conditions of agitation, temperature, and concentration identical to those used in the electrode studies. Analysis of the electrode studies by well established theories of electrochemical corrosion were made, and the results were found to bear a one-to-one relation with actual rate and potential measurements. Electrode Studies: The Anodic Reaction: The gold specimen used for all of the electrode studies and the rate determination consisted of a sheet of 99.99 + pct Au wrapped around a lucite rod and sealed at the edges with plastic cement, thus forming a cylinder of gold of known and constant area (8.0 sq cm). The lucite rod was threaded into a brass spindle which could be rotated at speeds of 100, 300, and 500 rpm. For the electrode studies electrical contact between the gold cylinder and the brass spindle was made by means of a gold strip covered with plastic. The anodic dissolution of gold was studied by immersing the electrode in a solution containing known concentrations of KCN and KAu(CN)2 but free of oxygen, and by passing an anodic current through the gold electrode. The pH of the solution was maintained between 10.5 to 11.0 in these and all other tests by addition of KOH. The pH was measured before and after each test by means of a glass-elec-

Jan 1, 1955

By A. J. Griest, P. D. Frost, J. R. Doig

During the past 5 years, research directed toward the development of titanium alloys having improved strength-ductility relationships and heat treatability has been carried out at Battelle for the U. S. Air Force.1"3 In the course of this work, a method of heat treating ß-stabilized titanium alloys was developed which produced a wide range of useful properties.4 The heat treatment consisted of two steps: a) solution treating at temperatures in the a-ß phase region, and b) overaging at a lower temperature in the range 800°to 1100°F. Corollary to the alloy development work, research was conducted on the mechanism of the heat-treatment reaction. The investigations of Frost and co-workers on isothermal transformation in Ti-Cr5 and Ti-Mn8 alloys disclosed the existence of the transition phase, w, during the course of the decomposition of metastable ß phase. Subsequent work at Battelle7,8 &apos;and at Case Institute by Brotzen and co-workerss further clarified the nature of the decomposition process. Beta decomposition was found to proceed by the following series of reactions: 1 2 3 4 a + Ti, My (in eutectoid systems). ßo, ßr, and ßU refer to ß phase of original, enriched, and ultimate alloy contents, respectively. Omega is a transition phase having a complex structure. 10-13 Step 4, of course, occurs only in ß-eutectoid systems. This paper presents data correlating transformation behavior with mechanical properties for the following alloys: Ti-8Mn, Ti-8Mn-2A1, Ti-4Mn-4A1, Ti-6Al-4V, and Ti-4Fe. The isothermal decomposition of ß in titanium-manganese alloys of similar composition has been investigated by Frost and coworkers8 and the effect of various annealing treatments on alloys in this system has been studied by Holden, Ogden, and Jaffee.14 The compositions Ti-8Mn-2Al, Ti-4Mn-4A1, and Ti-6A1-4V, were studied in the present work in an effort to define more clearly the effect of aluminum on the response to solution and aging treatments. Ogden, Holden, and Jaffee15 have invesitgated the effect of aluminum on the response of a similar alloy (Ti-8.8Mn-2.46A1) to annealing treatments, and Luini and Lee16 have made an exploratory investigation of the heat-treatability of the Ti-4Mn-4Al alloy. The Ti-4Fe alloy was studied as an example of a moderate1y active eutectoid system. Holden, Ogden, and Jaffee 17 have studied Ti-Fe alloys and have presented some hardness data for aging at 400°C for alloys of Ti-2.56, 5.01, and 7.35 iron after quenching from the a-ß field (750°C). EXPERIMENTAL PROCEDURES The experimental procedures generally used in the precipitation-hardening study are outlined in the following sections. Departures from these techniques are noted in the discussions of the individual alloys. Table I presents the nominal and actual compositions of the alloys studied, together with the swaging and rolling temperatures. In all cases, these temperatures were in the a-ß field and the microstructures consisted of an equiaxed a-ß mixture. Melting and Fabrication—Except for the commer-

Jan 1, 1960

By DeVerle P. Harris

Risk for most mineral investments is greater than that of average business ventures, because the physical and economic characteristics of the mineral deposit are never known with certainty. Inasmuch as the merits of a potential mineral investment cannot be fully appraised without consideration of the impact to the investor of the possible unfavorable events associated with the adoption of the project, methods of risk analysis are important in project evaluation and investment selection. The conceptual framework for risk analysis and the means by which some of the recommended practices might be implemented are examined. In addition to the normal business risk due to market forces, the physical and economic characteristics of the mineral deposit are never known with certainty, for only partial or indirect information is available, such as data from drill cores or surface and underground workings. Consequently, risk for most mineral investments is greater than that of average business ventures. Inasmuch as the merits of a potential mineral investment cannot be fully appraised without consideration of the impact to the investor of the possible unfavorable events associated with adoption of the project, methods of risk analysis are important in project evaluation and investment selection. This paper examines the conceptual framework for risk analysis and means by which might be implemented some of the recommended procedures. Utility Theory A discourse on risk and its impact upon investment selection quite often leads the reader into the concept of utility theory, for utility theory is a device constructed by economists to measure the satisfaction an individuai receives from a good; in the case of investment analysis, that good is the outcome of an investment. It briefly is reviewed here to describe the reaction of the individual to risk and as a stepping stone to other techniques more suited to risk analysis at the level of the firm. Utility theory proposes that an investor possess a utility map (curve), such as indicated in Fig. 1, which indicates the value in utiles of potential monetary rewards to an individual with some specific endowment of resources. Points on this map are obtained from the following relationship:

Jan 1, 1971

By R. C. Craze

This paper discusses the characteristics of the velocity logs now available to the petroleum industry, and some of their advantages and limitations. The velocity log was designed as an aid to the geophysicist to determine velocity layering in the earth and to provide fast, accurate and economical vertical travel time data. After a number of logs had been made, studies were carried out on their use ia correlating strata in adjacent wells. It was found that adjacent strata usually show sufficient velocity contrast to make it possible to correlate these from well to well, even in areas where electric or radioactive logs fail.&apos; In addition, velocity logs have been useful in the determination of porosity and thickness of reservoir rock.&apos; These uses for velocity logs require an understanding of the characteristics of the log in response to the changes in velocity and in borehole conditions encountered normally in logging. GENERAL DISCUSSION OF INSTRUMENTATION The measurement made in velocity logging is more accurately described as a measurement of time rather than velocity. Ideally the log is obtained by measuring the length of time required for compressional sound waves to travel through a fixed distance in the formation. In practice, the time measurement may be made accurately but the distance through which the waves have traveled may vary slightly. Changes in borehole diameter are responsible largely for the difficulty in maintaining a fixed distance, especially if the diameter variations are so abrupt and frequent that the borehole instrument cannot follow contours of the hole. Several service companies have velocity logging equipment available or under development which have different transmitters, receivers, and measuring systems. While these differences are important, there are actually only two systems in use at the present time (Fig. I)."&apos; The first system initiates a pulse at a trans-mitter and detects it at a single receiver. The transmitter and receiver are separated by a fixed distance, called the spacing. The time measured is that between the initiation of the pulse and the first arrival of acoustical energy at the receiver. The second system uses two receivers and a transmitter. The receivers are separated by a fixed distance and the time between arrivals of energy at the two receivers is measured. Here, the spacing is the distance between receivers. The two systems have much in common for it is possible to record both logs simultaneously. Usually the transmitter is an electro-mechanical transducer which produces discrete

By Malcolm McColl, C. A. Mead

Thin films (of mica have unique attributes that are exceptionally good for studies of high-field conduction mechamisms in thin-film insulators and the quantum mechanical tunneling of electrons from metal to metal. The principal advantages of using mica films are that the films are crystalline and the cleavage planes occur every 10Å. This property results in films whose thicknesses are integral multiples of 10Å and whose surfaces are uniformly parallel over sizable areas. Hence, very well-defined metal -mica-metal structures are possible. Furthermore, the fact that the insulator is split fro??! a bulk sample allows the index of refraction, dielectric constant, forbidden energy gap, and trapping levels and their density- to be obtained directly from measurements performed on thick samples Of mica rather than requiring that these properties be interred from the conduction characterrsties alone. In the work to he described, all the cleaving was done in a high vacuum just prior to the evaporation of metal elertrodes so as to avoid air contamination at the interfaces. Results of these studies indicate that the current through the 30 and 40Å films exhibited quantitative agreement with the theoretical voltage and temperature dependence derived by Strallon for the tunneling of electrons directly from metal to metal. Thicker films at room temperature exhibited volt-ampere curves suggesting Schottky emission of electrons from the cathode into the conduction band of mica. However, the thermal activation energy was smaller than that found from other measurements, and the experimsntal Schottky dielectric constant was larger than the square of the index of refraction. These facts would indicate that the electrons were being injected into polaron stales ill the iusulator. At low temperatures and high fields, the current through the thicker films did not exhibit the Fowler -Nordheim dependence as would be predicted by a simple extention of the theory of field emission into a vacuum. THE mechanism of electrons tunneling through insulating films has received considerable attention in the last few years due to the devices possible utilizing tunneling&apos;-4 and the success of tunneling in the study of superconductivity.5,6 Until the recent paper by Hartman and chivian7 on the study of aluminum oxide, there had been no reported successful quantitative experimental fit to the theory. Their method of fabrication necessarily results in a polycrystalline insulator, the stoichiometry of which is nonuniform from one side to the other. This structure also introduces complications to the shape of the barrier which is set up by the insulator since the insulator possesses a spatially nonuniform band structure and dielectric constant. Due to these facts an analysis of the data in terms of a pviori barrier shape is of questionable validity. The use of muscovite mica not only overcomes these disadvantages but, as an insulating thin film, provides physical properties (dielectric constant. trapping levels and their densities, forbidden energy gap, and so forth) that are identical to the easily measured values of the bulk sample. Furthermore, it is a single-crystal insulator whose cleavage planes (10Å apart8,9) provide uniformly parallel surfaces of well-known separation. This material is therefore ideally suited to the study of electron-transport phenomena. Von Hippel10 using a 6.5-µ-thick sample was the first to observe the high-field conductivity (=5 x l06 v per cm) of mica. No attempt was made to develop an empirical formula, but Von Hippel concluded from intuitive arguments that the current was being space-charge limited by trapped electrons. Mal&apos;tsev11 in a more recent investigation at high fields observed a dependence of the conductivity a on the field F of the form exp(ßF1/2). This dependence was attributed to the Frenkel effect,12,13 a Schottky type of emission from filled traps. No mention in the English abstract was made of the thicknesses of his samples or, and more important, of how well the value of ß fit Frenkel&apos;s theory. In 1962 Foote and Kazan14 developed a technique for splitting mica to a thickness of less than 100Å and observed a dependence of the current density j on the field of the form j = jo exp(ßF1/2) on a thin sample thought to be 40Å thick. Assuming that this was a Schottky emission process and that the appropriate dielectric constant for such a mechanism would be closer to a low-frequency value of 7.6, Foote and Kazan calculated from ß an independent thickness of the mica of 36Å. No further investigation was made of the phenomenon. However, the work reported in this paper indicates that the film measured by Foote and Kazan was probably 60Å thick, the error arising from the measurement of the very small metal-insulator-metal diode areas that were used, along with the diode capacitance and dielectric constant, to calculate the thickness. In the research reported in this paper, Foote and Kazan&apos;s technique was modified to cleave muscovite in a vacuum of 10-6 Torr, immediately after which metal electrodes were evaporated creating Au-mica-A1 diodes. Aluminum was chosen because of its strong adhesion to mica, as necessitated by the

Jan 1, 1965

By G. H. Bruce, C. E. Williams

The trend toward deeper drilling, together with the attcndant increase in power requirements for circulation of the drilling fluid, has emphasized the need for a critical examination of the factors affecting the removal of bit cuttings from the hole by the drilling fluid. The ability of drilling fluids to lift cuttings is called their carrying capacity. A series of laboratory and field experiments has been conducted to determine the minimrim annular velocity necessary to remove cuttings, and to investigate the effects of properties of drilling fluids on their carrying capacities. Consideration of the results of these experiments led to the following conclusions: 1. Turbulent flow in the well annulus is most desirable from the standpoint of cutting removal. 2. Low viscosity and low gel are advantageous in removing cuttings. 3. Increase in mud weight is effective in increasing carrying capacity. 4. The carrying capacity is higher when the pipe is rotated than when it is not. 5. If turbulent flow can be maintained, an annular velocity slightly higher than the slip velocity of the largest cuttings to be transported should keep the bore hole clean. This implies velocities of 100 to 125 ft per minute rather than the presently used 175 to 225 ft per minute. INTRODUCTION Power Savings by Reduction of Annular Velocities A large portion of the power expended in drilling operations is consumed in circulating the drilling fluid. An important factor in establishing the rate of mud circulation is the minimum velocity in the annulus necessary to remove bit cuttings. Empirically, it has been found that average annular mud velocities of about 200 ft per minute will remove cuttings. It was not definitely known, however, whether annular velocities of about 200 ft per minute were just above the minimum necessary to remove cuttings, or whether such velocities could be materially reduced without sacrifice of the ability of the mud to remove cuttings. It is apparent that if annular velocities could be reduced without impairment of cutting removal, a considerable saving in power requirements would result. Need for Research on Carrying Capacity The ability of a drilling fluid to transport cuttings is called its carrying capacity. Although it has been recognized that the carrying capacity of a mud is affected by mud properties such as viscosity and density1,2,3,4 there have been various views in the industry as to the effects of these mud properties on carrying capacity. The economic importance of the problem of carrying capacity and the scarcity of information on the subject indicated that research on the problem was needed. THE FACTORS AFFECTING CARRYING CAPACITY Qualitative Determination of Factors The mechanism of cutting transport is closely related to that involved in the separation of material by settling processes. A considerable amount of research has been done on settling problems, and discussions of sedimentation theory can be found in standard texts.5,6 Consideration of the information available from these sources, together with consideration of the mechanism of cutting transport, leads to the conclusion that the factors affecting carrying capacity are the dimensions of the system, the physical properties of the cuttings. and the physical properties of the drilling fluid. system Dimensions and Their Effect The dimensions of the fluid circulating system of importance to carrying capacity are the bore hole size, drill pipe size, pump capacity, and pump speed. These dimensions determine the annular velocity of the drilling fluid. Physical Properties and Their Effects The physical properties involved in the interaction between mud and cuttings are the density and shape of the cuttings and the density, viscosity and gel strength of the drilling fluid. The effect of the density factor on carrying capacity is fairly obvious; high density difference between cuttings and fluid results in a low buoyant force and therefore decreases carrying capacity. The effect of cutting shape is less obvious. Although

Jan 1, 1951

By Jei Y. Choi, Paul G. Shewmon

The surface self-diffusion coefficient of copper (D,) has been measured between 847° and 1069 "C for six different orientations. These were the(111), (110, (100, and three higher index surfaces. The activation energy for Ds (designated Q s) was found to be about 49 kcal per mol for all six surfaces, and Do about 2 x 104 sq cm per sec. At any temperature Ds varied by no more than a factor of three over these orientations. It is shown that, if the free energy of a surface atom is uniquely determined by its number of nearest neighbors, it follows from the Principle of microscopic reversibility that Qs should have the same value for all surface orientations, and Ds should vary little with orientation. This model also suggests that for clean fee metals Qs ~ 2/3 AH, (heat of vaporization). This is true for copper. ALTHOUGH it has been appreciated for several decades that atoms can diffuse more rapidly on a surface than through the bulk of a crystal, it has only been in the last few years that reliable values of the surface self-diffusion coefficient (Ds) have become available. Tracer studies of Ds had been attempted prior to this period, but when a tracer is placed on a surface, an ever increasing fraction of it is drained off into the lattice. The correction for this loss involves a very difficult, and as yet unperformed calculation. Those who have worked with tracers have not corrected for this loss.1, 2 Thus their results indicate that Ds is greater than the self-diffusion coefficient in the lattice (Dl), but it has not been established that they give quantitative data on Ds. A procedure which avoids the problem of tracer loss is to study the rate of mass-transfer under the effect of surface tension. If the surface asperity being studied is very small, the mass transfer occurs entirely by surface diffusion. The kinetics at which a grain boundary groove forms on an initially plane surface is a well-studied case of this type. The smoothing of a slight scratch in an otherwise flat surface is another procedure that has been studied. If these grooves are up to 20 to 30 µ in width, the dominant mechanism for mass transfer is surface diffusion (at least in the case of metals with low vapor pressures), and the widths can easily be measured with an interference microscope. Of these two, mass-transfer techniques only in the case of grain boundary grooving has a rigorous mathematical treatment been given. This was done by Mullins.3,4 His analysis predicted that in the case of copper in an atmosphere of an inert gas, surface diffusion should be the dominant transport mechanism. This analysis gave an equation for the groove profile and predicted that the width of the groove would increase as (time)1/4. Mullins and Shewmon showed that both of these predictions agreed with experiments.5 Thus the validity of the values of Ds given by this procedure seems to be well established. Gjostein has used copper bicrystals and the grain boundary grooving technique to determine Ds and the activation energy for surface selfdiffusion (9,) in the [001] direction on surfaces ranging between the (100) and (110) planes.= He reported that Qs = 41 kcal per mole and Do = 6.5 x 102 sq cm per sec for all orientations studied. Since the results did not change with the dew-point of the dry hydrogen atmosphere or the type of refractory tube used, he concluded that the surfaces were clean, or at least that the results were not influenced by any impurities chemisorbed from the atmosphere. The work reported here reproduces and extends Gjostein&apos;s study in that D s and Q s were determined for copper over a wider range of orientations. To study the effects of impurities, two purities of copper were used as well as cathodic etching to remove any possible electropolishing film. Gjostein postulated that the diffusing atoms on a surface near a low index plane are the few atoms which are adsorbed on the smooth region between ledges or steps in the surface. A more rigorous derivation of the equation relating Ds to the concentration and jump frequency of these adsorbed atoms is given here. Using this treatment, our empirical observation that Q s and D s are essentially the same for all surface orientations can be shown to follow from the assumption that the free energy of a surface atom is uniquely determined by its number of nearest neighbors. The studies of D s using the scratch technique have been carried out by Blakely and Mukura on nickel,&apos; and by Geguzin and Oveharenko on copper. The latter study using copper gives values of D s roughly

Jan 1, 1962

By Donald B. Evans, Robert D. Pehlke

The solubility of nitrogen in liquid Fe-A1 alloys has been measured up to the solubility limit for formation of aluminum nitride using the Sieverts method. The activity coefficient of nitrogen decreases slightly with increasing aluminum content in the range of 0 to 4 wt pct Al. Based on a nitride composition, AlN, the standard free energy of formation of aluminum nitride from fhe elements dissolved in liquid iron has been determined to be: ?F" = -59,250 + 25.55 T in the range from 1600º to 1750ºC. The solubility of nitrogen in liquid iron alloys and the interaction of nitrogen with dissolved alloying elements in liquid iron have been the subject of a number of research investigations.&apos; Most of this work, however, has been reported for concentrations well below those necessary for the formation of the alloy nitride phase. Data in the concentration region near the solubility limit of the alloy nitride, particularly for systems exhibiting stable nitrides, are important in evaluating the denitrifying power of various alloying elements. They are also useful in determining the stability of a given nitride if it is to be used as a refractory to contain liquid iron alloys. In view of the importance of aluminum as a deoxidizing agent in commercial steelmaking and the fact that its nitride, AIN, is a highly stable compound and has merited some consideration as an industrial refractory, the following investigation was undertaken. The use of the Sieverts technique provided a measurement of the equilibrium nitrogen solubility in liquid Fe-A1 alloys as a function of nitrogen gas pressure up to 3.85 wt pct A1 in the temperature range of 1600º to 1750°C. The values obtained by the Sieverts method were checked by means of a quenching method in which liquid iron was equilibrated with an A1N crucible under a known partial pressure of nitrogen gas, and the solubility of A1N in liquid iron determined by chemical analysis. EXPERIMENTAL PROCEDURE The theoretical considerations involved in determining the solubility product of a solid alloy nitride phase in liquid iron by measuring the point of departure of the nitrogen gas solubility from Sieverts law have been discussed by Rao and par lee.&apos; The principal problem is to determine the variation of nitrogen solubility in an alloy as a function of the pressure of nitrogen gas over it with sufficient precision to establish the break point in the curve at the solubility limit of the alloy nitride phase. A fairly large number of data points are required to do this. A second problem is the determination of the composition of the precipitated solid nitride phase. This is necessary in order to define completely the thermodynamic relationships. The Sieverts apparatus used to make the nitrogen solubility measurements in this investigation is of essentially the same design as that described by Pehlke and E1liott.l The charge materials were Ferrovac-E high purity iron supplied by Crucible Steel Co. and 99.99+ pct pure aluminum. Recrystal-lized alumina crucibles were used, and were not attacked by the liquid alloys. The hot volume of the system which was measured for each melt ranged from 46 to 50 standard cu cm and was found to decrease linearly with decreasing pressure and with increasing temperature. The temperature coefficient of the hot volume at 1 atm pressure of argon gas was essentially constant for all experiments at a value of -6 X 10-3 cu cm per "C. The melt temperature was measured with a Leeds and Northrup disappearing filament type optical pyrometer sighted vertically downward on the center of the melt surface. The temperature scale was calibrated against the observed melting point of pure iron taken as 1536°C. The emissivity of all melts was assumed to be that of pure iron, taken as 0.43. The charge weights ranged from 110 to 140 g and the range of aluminum contents covered was from 0 to 3.85 wt pct. Aluminum additions were made as 12 to 15 wt pct A1-Fe master alloys previously prepared in the system under purified argon. The compositions of the master alloys were checked by chemical analysis and found to be in agreement with the charge analyses. Vertical cross sections of the master-alloy ingots were used as charge material for the equilibrations in order to minimize the effect of any segregation which might have occurred during solidification of the master alloys. Determinations of the solubility product of

Jan 1, 1964

By R. S. Shoemaker, R. M. Darrah

Expanded markets for copper in the past few years and a consequent search for new ore bodies have revitalized the widely known but seldom applied method of producing copper called heap leaching. Heap leaching is defined here as the process applied to oxide ores which have been mined solely for the purpose of leaching. In this case, all costs of mining the ore become a part (and a substantial one, as will be shown) of the cost of the copper produced, whereas in dump leaching the mining cost has already been accounted for as a stripping cost for the sulfide ore. Of course, with newly opened ore bodies, stripping costs may be divided through accounting procedures, between the copper produced by the mill and that obtained by leaching, but in general this type of operation must be economic on the basis of the sulfide ore alone. Heap Leaching Requires Low Capitalization Heap leaching, as a beneficiation method, is unique in that it is the only process used for the recovery of a metal in which the time involved from mining the ore to metal production is measured in months instead of hours or at the most, days. Then too, after the ore body has been depleted and mining has ceased, metal production will continue for some substantial period of time. Heap leaching is also unique because unlike any other method of beneficiation, metal recovery cannot be accurately forecast ahead of time and recovery will never approach that of a conventionally milled sulfide ore or even that of a vat leached oxide ore. Counter-balancing this drawback, however, is the relatively low capital expenditure necessary to put a heap leaching operation into production and the consequence that smaller ore bodies which would not support the higher capital cost involved in a vat leaching plant can be made into producers. Stated more simply, in heap leaching the operator accepts low recovery in exchange for low capital costs and low break even point. Whether the operator chooses vat leaching with its higher recovery and higher capital costs, is a mater of economics which depends in part on the nature of the ore to decide. For instance, an ore that will vat leach in 7 to 10 days using 7 pounds of sulfuric acid per pound of copper produced might use double or triple that amount of acid during the months that are required for heap leaching.

Jan 12, 1968

By Y. Shimomura, M. Serizawa, Y. Takahashi, K. Miyagawa

The "semi-pellet" sintering method developed and currently being used at the Fuji Iron & Steel&apos;s Hirohata Works is discusssd. It is shown that the method makes fine-sized material easily sinterable and increases sinter production. The operation can be incorporated readily into conventional sintering plants. Sintering plant raw materials currently being used in the Hirohata Works consist of 40 pct pyrite cinder, 40 pct fines resulting from crushing and screening of imported ores, and 20 pct others, such as mill scale and iron sands. Pyrite cinder, a major component in the sinter feed, has been getting finer since 1952, due to the increased grinding required for the improvement of the results in the iron sulfide flotation and to the adoption of FluoSolid roasters in sul-furic acid plants; some fines pass 100-mesh sieve almost completely. Increased use of the fine-sized pyrite cinders in the sinter raw mix resulted in such difficulties as decreased bed permeability, uneven firing conditions, and low yield. In an attempt to study the cause and to find a remedy for this problem, a series of experiments were made, using an 80-kg experimental sintering pan. As a result it was established that, by rolling the fine-sized pyrite cinders into small balls of 10 to 3 mm diam (hereafter called semi-pellets) and mixing them into the sinter raw mix, the bed permeability was improved, the sintering time shortened, and the yield and production rate increased. It is proposed that this new method be called the semi-pellet sintem&apos;ng. In recent years the pelletizing process has taken the spotlight in the agglomeration field for treating fine-sized ores here in Japan as well as in the U.S. and Europe. This process produces pellets suitable for the blast furnace charge as such, and consists of three major operations: fine grinding, balling, and firing. With regard to the firing technique, some problems still appear unsolved. In the semi-pellet sintering, however, several ad- vantages can be claimed: the balling operation is relatively simple because only small-sized balls are shown to be acceptable and the operation can be readily incorporated into the conventional sintering plant, since only balling, not grinding or firing, equipment is needed. Basic test work on the process was initiated in 1954 and favorable results were obtained. Accordingly a pilot plant was built in 1955 and the test work was continued. The semi-pellets thus prepared in the pilot plant were tested further by USing them in the actual sintering pan and their beneficial effects ascertained. In late 1956 a drum-type balling machine (2.4X4 m) was installed and it went into operation in April 1957 in conjunction with the Greenawalt sintering plant (8 pans having dimensions of 7.2 m in length, 3 m in width, and 0.3 m in depth). In October 1958 a cone-type pelletizer, with a 2.2 m diam, and later a disk-type pelletizer were further added in the plant. In the DL sintering plant (2000 tpd), newly built in July, 1960, four disk-type pelletizers (3.2 m diam, 10 tph capacity) were installed. By mixing the semi-pellets thus prepared with the feed, the sintering operation was found to be greatly improved. The results of the basic test work, and the equipment and operation of the semi-pellet sintering operation at the Hirohata Works will be described. ON THE SINTERING CHARACTERISTICS OF FINE SIZED PYRITE CINDERS To ascertain the effect of addition of fine-sized pyrite cinders on the sintering characteristics, a series of measurements on bed permeability was carried out by varying the size distribution of pyrite cinders. The composition of the raw mix used in the tests was fixed at 50 pct pyrite cinder, 20 pct Larap magnetite fines, 30 pct sinter return, and 5 pct coke; only the size distribution of the pyrite cinder was varied. Also the moisture content was changed at each size distribution. The results are given in Fig. 1. For all pyrite cinders tested the bed

Jan 1, 1961

By L. D. Mullins, E. B. Elfrink, W. L. Wahl

In the past few years several articles and papers presenting results of solution gas-drive depletion calculations have appeared in the lit-erature. Such calculations are of interest to the oil industry, for investment decisions must often be made before much is known about a reservoir. At other times, an estimate of the possible benefits to be realized from alternate production methods is desirable, and theoretical depletion calculations can serve as a floor or reference level from which to work. In any case, an estimate of ultimate oil recovery based upon engineering data is commonly required. An engineer confronted with the problem of obtaining, for a specific reservoir system, an estimate of ultimate oil recovery by solution gas-drive depletion usually will be forced to perform the calculations himself. This is despite the quantity of data in the literature. Rarely will either experience or the literature provide results from a reservoir system similar in all important respects to the one under consideration, and calculated results are not so plentiful that satisfactory interpolation procedures can be devised. Performing the calculations, however, is a tedious, time-consuming task unless an electronic computer is available, and, in practice, time and manpower are not always available for this purpose. A quick, simple, consistent method was needed for reducing the uncer- tainty in estimated oil recovery from solution gas-drive reservoirs when only minimum information about the reservoir system is available. PROCEDURE Method of Calculation The usual requisite assumptions were made so that the material balance equation could be used to calculate data for the charts. The following assumptions were made: (1) the reservoir is homogeneous and isotropic; (2) oil recovery is due entirely to solution gas drive and neither a gas cap nor a water drive nor gravity drainage is present; (3) the initial reservoir pressure is the bubble-point pressure of the reservoir fluid; (4) initial total liquid saturation is 100 per cent of pore space; (5) interstitial water saturation remains at the initial value as the reservoir pressure declines from the bubble-point pressure to atmospheric pressure; (6) equilibrium gas saturation is 5 per cent of pore space; and (7) oil and gas saturations are uniformly distributed throughout the reservoir at all times. There are no saturation gradients due to a wellbore, nor is the geometry of the reservoir system considered. The material balance equation was written in the form of a differential equation&apos; which was integrated to determine the change in oil saturation for an assigned pressure drop. Formal integration was not possible, so recourse was made to the Runge-Kutta method&apos; of numerical integration. All computations were performed on IBM equipment. Numerical integration yielded the change in oil saturation within the reservoir as the pressure. declined from the bubble-point pressure to atmospheric pressure. The initial oil saturation minus the change in oil saturation yielded the oil saturation at atmospheric pressure. The oil originally in place was obtained by dividing the initial oil saturation by the initial formation volume factor (differential liberation) while the oil in place at atmospheric pressure was obtained by dividing the final oil saturation by the formation volume factor at atmospheric pressure. U1timate oil recovery, expressed as a percentage of the initial oil in place, was obtained by dividing the difference between the oil initially in place and the oil in place at atmospheric pressure by the oil initially in place and multiplying by 100. PVT Data Charts were based upon 135 solutions to the material balance equation. PVT properties of the reservoir fluids were variables in this equation and had to be known as functions of pressure. The required PVT data might have been obtained from either actual reservoir fluid systems or correlated data. However, correlated PVT data were developed and employed in the calculations for the following reasons: (1) it is doubtful that 135 sets of PVT data could have been obtained for the values of variables investigated in this study, and (2) results of recovery calculations from randomly obtained PVT data could not be correlated as well as rssults from selected PVT data. The PVT data used to develop the

By J. P. Boisseau, C. N. J. Wagner, E. N. Aqua

An analysis ulas made of powder-paltern peaks from cold-rolled polycrystalline copper and from copper powders, compacted into briquets (1 in. diameter) with pressures up to about 106 psi. Powder-pattern peaks from both contact faces were measured with a diffractometer and CuKa radiation. Laltice-parameter measurements indicate the presence of residual stresses in the bulk specimen of the order of a - -10 kg per sq mm after 93 pct reduction in thickness, and give some evidence for the occurrence of deformation stacking faults (probability a - 0.003) in both bulk and powder samples. Fourier analyses of the line profiles were carried out on the (111) - (222) and (200) - (400) Pairs of reflections. The particle sizes decrease rapidly with increasing deformation and reach asymptotic values of De (111) = 550A and D, (200) = 350A at about 25 pct reduction in thickness or 80,000 psi pressure for compaction. The anisotropy of the particle sizes indicates the presence of microtwins and stacking faults on (111) planes. The rms strains increase also with deformation and reach limiting values of 2 x 10-3 in the [100] direction and 1 x 10-3 in the [Ill] direction at a distance L = 100A normal to the reflecting planes. THE diffraction of X-rays in cold-worked, polycrystalline, fcc metals and alloys yields Debye-Scherrer patterns in which the individual (hkl) lines may show a broadening, a shift, and an asymmetric shape.&apos; These effects can be explained by the fragmentation of the small, coherently diffracting domains, the presence of residual elastic strains in the lattice, and the formation of stacking faults. X-ray studies of stacking faults in fcc metals and alloys have been methodically performed during the last few years, but so far most of the investigators dealt with cold-worked powder specimens obtained by filing.2-8,10-19 In such specimens, the crystals are randomly oriented and the average elastic strains are assumed to be zero, so that the observed peak shifts are due to stacking faults only. The agreement between X-ray diffraction theory1,20 and experiment is generally good. On the contrary, cold-worked, polycrystalline bulk specimens (after wire drawing, rolling, plastic deformation by tension or compression, etc.) contain residual elastic strains, which may not average to zero in the surface of the specimen and show very strong preferred orientation of certain lattice planes (texture) parallel to the specimen surface. Nonzero elastic strains also produce peak shifts, the magnitudes of which depend upon the crystallographic orientation of the reflecting lattice planes in elastically anisotropic materials as well as on the type of plastic deformation and which have to be taken into account when measuring stacking-fault probabilities in deformed bulk specimens.21-23 The purpose of the present investigations was to perform a detailed X-ray analysis on a bulk specimen of a fcc metal deformed by rolling at room temperature and on powder of the same material deformed by compaction, and to compare these results with those previously obtained on cold-worked filings.18 Pure copper was chosen for this study since it is known to produce only a small quantity of stacking faults by filing at room temperature.3,16,17,19 The residual elastic strain in the surface of the bulk copper should be the predominant factor determining

Jan 1, 1965