Search Documents

By Thomas Fraser, H. F. Yancey

The jig may be termed the standard coal-washing machine. Although exact figures on the relative tonnages of coal treated by the various coal-cleaning processes are not available, it is known that a large part of all the coal given special cleaning treatment is handled by jigs. This wide use of the jig warrants a special study of its performance. In this paper are presented the results of an analysis of work done by a three-compartment jig in treating bituminous coal from the Thick Freeport bed in Allegheny County, Pa. Certain systems of washing coal require sizing before washing, while others treat unsized coal. The prevailing practice, however, for the preparation of coking coal from the more easily washed coal is to treat an unsized or natural feed of about — 1 in. size and smaller. Under such conditions, the minimum size of particle that is beneficiated has long been and is still a matter of discussion and conjecture. In a careful laboratory investigation J?ngstl concluded that the practical limit of settling of fine coal is reached at from 0.02 to 0.008 in. On the other hand, Hancock2 has found that single-compartment jigs, used in preparing coal for the domestic market, usually allow most of the heavy (refuse) particles smaller than 1/4 in. to go into the washed coal. He also states that it is impossible with the ordinary coal jig to make any noticeable improvement in the quality of the coal finer than 20 mesh (about 1/30 in.). Because of its importance in coal cleaning, the work described in this paper was undertaken for the purpose of obtaining information on this subject, as a part of the general coal beneficiation program being carried out by the Bureau of Mines.

Jan 1, 1925

By J. M. Gaines, C. H. Herty, M. W. Lightner, H. Freeman

Few subjects have attracted the attention of metallurgists more than oxygen in steel. From the days of Mushet and Ledebur interest in this subject has been increasing, and as additional knowledge has become available, the problem has naturally grown more complex. Instead of using the simple term "oxygen" we now distinguish between iron oxide, silicates of various kinds, oxysulfides, oxygen as gas and oxygen in solid solution in steel. There are five general methods for determining oxides in steel: hydrogen reduction; vacuum fusion; various wet-extraction methods, including electrolytic methods; methods depending on volatilization of the iron away from the oxides; and metallographic methods. For oxygen in solid steel each of these methods has both advantages and disadvantages. The hydrogen-reduction method is of no use on steels above about 0.20 per cent. carbon;' furthermore, it gives only FeO and possibly some MnO. The vacuum-fusion method2 is expensive and gives total oxygen, with the exception of some A12O3, and does not differentiate between the various oxides in which the oxygen exists. Most of the wet extraction methods3 give only the more insoluble oxides SiO2 and A12O3, though the iodine method gives MnO to an uncertain degree (information that may be more misleading than no information

Jan 1, 1930

By Dever Ashmead

ENGINEERS, operators, miners, and others di-rectly interested in mining will readily agree that more of well-directed illumination in mines will result in a reduction of accidents and general im-provement in the working conditions, comfort, and effi-ciency of those employed underground. Progress has been made in the amount of illumination from individual lamps carried by miners. The candle, which a great many of us can remember as the general method of lighting, was replaced by the oil lamp or torch, later by a specially prepared oil known as "Sunshine," and eventually by the carbide cap lamp. The metal mines still present a field for progress from the standpoint of general illumination, particular-ly those mines having high stopes. Attention is being more and more focussed upon the advantages of im-proved lighting in mines, in order that the underground employee may benefit as the factory workers have al-ready done. The management is vitally interested in the morale of its employees, the reduction of costly accidents and increased production, all of which, judging by results in other industries, will be sub-stantially benefitted through the means of improved general illumination. From data available to the writer, 40 to 50 per cent of the accidents in the metal mines occur at the face; they may be due to roof falls, movement of loose ore, loading of cans, handling of tools, etc. Very probably a large proportion of these accidents may be attributed to lack of light. If sufficient illumination had been present the employee could have seen what was happen-ing and taken the proper precautions. The introduc-tion of better illumination means better visibility, de-crease in accidents, and increase in efficiency.

Jan 6, 1928

By Frank Foote, V. H. Nordstrom, Eric R. Jette, Bernard Queneau

The nickel-chromium alloys form the base for many industrial heating alloys, so that this system is of considerable practical importance. The literature on these alloys, however, contains much conflicting evidence, not only regarding the solubility limits of the terminal solid solutions at different temperatures but even regarding the number of phases existing in the system. Part of the difficulty undoubtedly arises from the fact that chromium of sufficiently high purity has been available only during the last few years. A second and possibly even more important difficulty arises from the ease with which chromium reacts with silicon and carbon compounds and the atmosphere to form silicides, carbides, nitrides and oxides. Pilling and Kihlgrenl in 1929 reviewed the existing scanty information. They did not consider the diagram by which they summarized the various bits of information to be entirely satisfactory. Matsunaga2 investigated the system by thermal analysis, microscopic examination and other means. Electrolytic nickel of 99.9 per cent purity and thermit chromium containing 0.30 per cent Al, 0.40 per cent Fe, 0.25 per cent Si and 0.04 per cent C were used. A Tammann furnace with hydrogen flowing through it was used for melting. Sekito and Matsunaga3 reported an X-ray investigation, presumably on these same alloys, which, as far as can be judged from the abstract, essentially confirmed the thermal and microscopic results. Nishigori and Hamasumi4 found compositions for the terminal solid solutions in equilibrium at the eutectic temperature which agreed fairly

Jan 1, 1934

By John Boardman

THE Anaconda company has never indulged in any employee activities at Butte which might be termed paternalistic, but it has exerted a vast amount of effort in care of its employees during working hours. The reason for this policy is not lack of interest or that the company does not feel the effect of employees' activities while they are "off the job"; it is that the company and the city of Butte have grown up together and, each has been adequate in its own sphere, the company in providing employment at the highest possible wage and the city in providing housing, sanitation, commercial services, medical services, schools, churches, amusements and entertainments. The one exception to this independence between the company and the community is the Butte Water Co., which is a wholly owned sub-sidiary of the Anaconda Copper Mining Co. Mention of this relationship is made here because the water supply of such a city as Butte is one of the principal factors in determining the health of the people. Very early in the development of the Anaconda company an adequate and dependable water supply for the operations became necessary, therefore the company took over this important community function. So well has this activity worked out that during the whole period of time covered, in which the company has expanded to become practically the sole mine operator and the community has grown from a small mining camp to the status of a modern city, there has been no shortage of water or any outbreak of water-borne, epidemic disease.

Jan 1, 1938

Development: Iron Ore In Peru Utah Construction Co., of San Francisco and a Peruvian Government corporation have signed an agreement for development of a large iron orebody in Peru. Most tests show 60 pct iron or better. Most of the ore is magnetite. Although ore will be shipped mainly to Eastern U. S. blast furnaces, shipments to the West Coast may develop as the orebody opens up. The construction firm indicated three American steel companies have shown interest in the project. The orebody is located 300 miles south of Lima and about 15 miles from the coast at the same longitude as New York City. Allen D. Christensen, executive vice-president of Utah Construction noted that the distance is shorter between Peru and the East Coast. The ore deposit measures about four to five miles in one direction and 10 miles in the other. As many as 15 outcroppings within these limits have been reported. Several of the outcroppings are thousands of feet long by several hundred feet wide, Christensen said. Shipments between 100,000 and 200,000 tons of ore per month are projected by the company. Cost of opening the mine to production may go over $5 million, Christensen said. It would include building of docks for ocean going vessels, housing, and heavy duty mining and processing equipment. The contract with the Peruvian government gives Utah Construction six to eight months for additional tests and a 20 year concession for mining the orebody. Peru will collect royalties on all ore. The company will also supply about 300,000 tons per year for an electric furnace to be installed by the Peruvian Government at Chimbote. No steel is produced in Peru now. Utah Construction formed the Argonaut Mining Co. last year, and was shipping iron ore from British Columbia to Japan at a rate of more than 50,000 tons a month, before winter weather decreased operations.

Jan 1, 1952

By M. B. Yung

Location THE Fu Chuan district lies near the eastern boundary of Kwang Si province in southern China and is connected with the coast by the West river and its branches. The Journey The first part of the journey from the coast is made very comfortably in one of the West river steamers which runs to Wuchow, the great distributing center for tile whole province. From here there are two ways of reaching the Fu Chuan district. One is to drop clown the West river for 15 miles and ascend the Yuen river for 120 miles. The other is to ascend the Fu river, which joins the West river at Wuchow, and at Ping Lok tike chairs across country. Of the two the former is the more direct and shorter but for other reasons I chose the latter. At Wuchow one must provide his own means of transportation, which may be a native boat anywhere up to 40 ft. in length, but not over 18-in. draft. The method of working these river boats against the swift current which in many places develops into rapids is interesting and worthy of note. Tracking along the bank with the tow line attached to the mast head is the most common procedure, but poling, sculling, sailing and winding up the rapids by a windlass are used as the case may require. The boatmen are the hardiest set of fellows I have ever seen often putting in 15 hr. of the most exhausting labor. The average clay's run against the current is 15 miles. On this trip one should have his own food, bedding and servants, and a guard of 10, or more soldiers is almost a necessity as certain parts of the river are infested with pirates.

Jan 9, 1914

By J. D. Kalasky

Continuous mining has revolutionized the coal industry but intensified the problems of earlier mechanization. From the installation of the first miner, it was recognized that face ventilation would be one of these problems. To establish an efficient work cycle for the equipment being used, conventional mechanized mining provides four or more development faces. Continuous mining, relying on a single machine, requires only one face, although more than one can be driven alternately by the same machine. In gaseous areas mined by the older methods, the intermittent rate of exposure allows time for the face to bleed off or be cleared, and the width obtained with conventional units makes it possible to hang a brattice line almost to the face. Continuous mining increases the ventilation hazards; there is no margin of time, and very limited space. For all practical purposes, continuous miners available today can be grouped into two major types, rippers and borers. The two can be further classified, respectively, as flexible and rigid. Both types have been in operation in U. S. coal mines for the past five to ten years in a number of seams, under various conditions ranging from slightly gaseous to very gaseous. Common methods of face ventilation utilizing jute or plastic brattice material for line curtains, stoppings, and checks have so far met with success. Air volumes to operating sections are greater than for conventional mining, and specific instructions have been given to section crews stressing the precautions needed in dealing with a steady rate of gas emission and the importance of maintaining reasonably air-tight brattice to direct a good steady flow toward the face at all times. Operators of continuous miners, as well as the foreman on each section, are equipped with an approved safety lamp for gas testing. When the miner is in steady operation, tests for gas at the face are made at 15 to 30-min intervals, depending on the

Jan 1, 1960

By A. W. Hesse

Twelve years ago, some coal-mine operators, mining engineers, oil and gas operators, Bureau of Mines engineers, geologists and state mine inspectors met in Pittsburgh, Pa. to discuss and solve if possible, the problems in connection with the drilling of oil and gas wells through or near coal mines and through the future coal reserves. Regulations were drafted and presented by O. P. Hood and A. G. Heggem of the Bureau of Mines.' . There was considerable discussion of the various articles, practically all of which appear in Bulletin 65, but the interest aroused at that meeting was short lived. Practically none of the important coal-producing states gave the matter the consideration it should have received. Notwithstanding the marked progress in safety work, coal mines still have an unenviable reputation for mine explosions. Our mining laws have become stricter and the enforcement, especially in Pennsylvania, more rigid, but what good will come from a rigid enforcement of the mining laws if some source of danger exists all around the mines, over which the operators have no control ? It is hardly necessary to recite all the cases of natural-gas explosions published in Bulletin 65, but with some of them I am especially familiar. In 1912, while visiting the Miners' Hospital, at Fairmont, W. Va., my attention was called to a patient swathed in in bandages so that no part of his face and hands were visible. He had not been told that his two sons, mere boys, had died of the burns they had received in the same accident—explosion due to natural gas leaking into a country mine at Peora, Harrison Co., W. Va.

Jan 1, 1925

By R. M. Murray

Although blister copper has been produced at the Mount Lyell Mining and Railway Company's works since 1896, it is only during the past five years that electrolytic refining has been undertaken locally, this having been done previously at customs refineries, at first in the United States, and afterwards at Port Kembla, New South Wales. Left to right: smelter building, converter building, blower building (in which converter-generators are housed), tank house and anode dock. Wire-bar furnace building in background at center. Possessing a hydroelectric power plant capable of generating power considerably in excess of the requirements of its mines and works at the time, the company was in a favorable position to undertake its own refining work, provided this advantage was not offset by the high cost of coal, which would have to be imported from the mainland, and provided also that the capital cost of the plant would not be unduly large in regard to the relatively small amount of copper to be treated. A study of these several conditions led to the adoption of a high-density plant using blister-copper anodes and equipped with an electric boiler to provide any

Jan 1, 1934

By S. R. Goodman, Hsun Hu

PREVIOUS investigations on the temperature dependence of rolling texture transition in high-purity silver1'2 and in electrolytic copperS have shown that a brass-type texture is favored at low rolling tem- peratures, whereas a copper-type texture is favored at high rolling temperatures. The transition takes place gradually as a function of the temperature of deformation, and a general correlation between texture transition and stacking-fault frequency or probability exists—a copper-type texture is associated with low stacking-fault frequencies, and a brass-type texture is associated with high stacking-fault frequencies. If the stacking-fault energy is calculated from the stacking-fault frequency and the dislocation density of the specimen, one finds that with low stacking-fault energies a brass-type texture will be developed, and that with high stacking-fault energies the texture will be of the copper-type. These findings are consistent with the idea that the formation of rolling textures in fcc metals may depend on their stacking-fault energy, although results of such nature always involve the ambiguity that a change in the density (or width) of stacking faults produced by deformation at different temperatures may be actually due to a variation in the stress, rather than due to a change in the specific stacking-fault energy per se. It has also been shown that the type of annealing texture depends entirely on the deformation texture. From a copper-type rolling texture, a strong cube texture will be formed upon recrystallization, whereas from a brass-type rolling texture, the annealing texture will be quite different from the cube orientation. Based on these results on texture transition in pure fcc metals, it appeared possible to effect a

Jan 1, 1963

By Ray Arms

This paper includes a brief classification of dry-cleaning devices, with a theoretical discussion of the principles involved. It outlines the methods of handling dust and screening difficulties at the McComas plant, as well as other plants that are being constructed and other dry-cleaning devices being developed. It describes the American Pneumatic Separator and discusses the sizing required, the effect of moisture in the raw coal, disposition of the middlings, and other aspects of the process. It gives s results of tests on various coals, and results of operation at Raton and McComas. DRY CLEANING, or pneumatic separation, is not, strictly speaking, a recent discovery. Among the archives of the Patent Office may be found many patents dating back as far as 1850 which cover early attempts to separate materials of varying specific gravity or of different shape by means of air. Hundreds of patents covering this art have been issued, which may be roughly classified into four general groups, as follows: 1. Stationary devices with pulsating air currents. The separating surface is usually riffled and air is supplied by bellows or compressors. This group' also includes air jigs, which have been used rather extensively. 2. Stationary devices with continuous air currents. These submitted the material to a continuous current of air, either horizontal or vertical. Chaff is blown from wheat by such a device. 3. Reciprocating or vibrating devices with pulsating air. A small group in which the pulsating air is supplied by bellows and some motion provided in the separating surface to move the stratified material to various discharge points. 4. Reciprocating or vibrating devices with continuous air supply. This is by far the most important group and all recent developments have been along this line. All of the above groups involve the stratification of material by air and include none of the dry methods that use other principles, such as coefficient of friction, magnetism, etc.

Jan 3, 1924

By Henry M. Howe

in Cast-Iron. It has been generally accepted that the presence of silicon in cast-iron leads to the formation of graphite; and this has been explained by saying that the silicon lowers the solvent power of iron for carbon at and somewhat below the freezing-point, so that, in the presence of silicon, the iron is unable to retain in solution or combination the whole of the carbon with which it has united while molten, and therefore expels the excess of carbon in the form of graphite, during and immediately after solidification. Probably the best way to study this question would be to examine pure cast-irons, i.e., those containing nothing but iron, carbon and silicon, which at the same time should have been saturated with carbon when molten. But the data for such a study are not at hand; so we must turn to commercial pig-irons as they are made in the blast-furnace, and before their composition has been changed by remelting. Much evidence has been offered of late, tending to oppose the theory of the action of silicon above set forth. Some of this evidence will be examined here. 1. Mr. Bachman's Results. In particular, Mr. F. E. Bachman† has published a collection of analyses of cast-iron, in which the proportion of graphite at first appears to be nearly independent of the proportion of silicon present. Thus, in his Table LI., we find that with pro-

Jan 1, 1901

By F. L. Ransome

THAT geology and mining should stand in close and mutually helpful relationship was recognized in the United States at an early period, but it is not possible to set a precise date at which the study of ore deposits became a thoroughly reputable and important branch of geological science. As early as 1850, appeared the first ,part of Foster and Whitney's report1 on the Lake Superior region, devoted mainly to the copper-bearing areas, followed, in the succeeding year, by the second part,2 on the iron lands. This appears to have been the first comprehensive report on what might, at that time at least, be called "western" ore deposits to be prepared and published under the auspices of the Federal government. An outgrowth from this work was Whitney's Metallic Wealth of the United States,3 which appeared in 1854. It was the earliest general work on the ore deposits of the country, and remained a standard reference book for marly forty years. From 1853 on, various parties were sent out by the War Department to explore routes for proposed railways and wagon roads from the Mississippi Valley to the Pacific Coast. Geologists were attached to most of these parties, but their work was mainly of broad reconnaissance character, little attention being paid to ore deposits. Although the

Jan 1, 1933

By Webster Hodge

MALL generators and motors are required to Soperate, in some critical applications, at temperatures where cold-worked silver-bearing copper re-crystallizes. Copper containing up to 30 oz Ag per ton has been used for many years to build the highest grades of commutators and slip rings. With failure of commutators impending because silver-bearing copper cannot withstand the stresses imposed at these higher temperatures, Cr-Cu was tried as a substitute with varying degrees of success. Cr-Cu proved difficult to fabricate because a critical heat treatment was necessary to obtain sufficient ductility. Besides, its rupture strength was shown to be low at operating temperatures, its electrical conductivity lower than desired, and its cost high. Furthermore, it often contained hidden flaws. The Nippert Electric Products Co. set out to find a better material by undertaking a research project with the stated objective of providing a material suitable for commutators that would have 1) a softening temperature above 750°F (400°C), 2) a minimum electrical conductivity of 90 pct of that of pure copper, 3) a strength not less that that of cold-worked silver-bearing copper, and 4) a materials cost of not over 1.5 times the cost of copper containing 25 to 30 oz Ag per ton. No commercial alloy met these specifications. However, it was found that copper containing from 0.18 to 0.35 pct Zr could be produced quite easily in the laboratory, and promised to fulfill the major requirements noted above. Interest naturally centered in the lower part of this composition range, since such alloys gave somewhat better electrical conductivities, and were lower in

Jan 1, 1958

THROUGH the courtesy of the Southern Appala-chian Coal Operators' Association, a joint meeting of the Southern Appalachian Efficiency Associa-tion and local members of the A. I. M. E. and A. S. M. E. was held at Knoxville, Tenn., on Nov. 12. In introduc-ing the subject and stating the object of the meeting, H. Foster Bain, speaking for the. Institute members, said "Shoveling coal is the largest job of hand labor re-maining in this country, with the exception of the mis-cellaneous work on the farms, and even there nearly all the big jobs are now performed with the help of machines. The men in the coal mines, by hand labor, dig, each year, more cubic yards than were taken out of the Panama Canal. It has been a natural ambition of engineers, operators and men alike to follow here the characteristic lead of American industry and to substi-tute as far as possible the work of machines for the work of men; to promote the latter to the position of con-trolling and directing mechanical power rather than being themselves the machines that lift the coal from the floor of the room into the mine car. "Handling materials is one of the regular jobs of mechanical engineers, and the American Society of Me-chanical Engineers maintains a Materials Handling Division for discussion of the technical problems con-cerned. Having in mind the excellent results that had flowed from application of mechanical power and de-vices to these problems in factories, port terminals, warehouses, and other above-ground plants, the Me-chanical Engineers began to consider the possibility of introducing similar methods underground. Individual-ly, many were called upon to design, erect and operate machines for such use and at once they found them-selves faced by many novel conditions and difficulties. The Division thereupon planned a general meeting in New York in March, 1926, for consideration of problems and progress in this field. The Mining Engineers. and representative coal operators were invited to attend and

Jan 12, 1927

By J. L. Keats

IN THE literature on the elimination of metalloids in basic open-hearth practice, there are a great many heats recorded in which excellent data on changes in slag and metal composition during refining are given, but in almost all of these heats either temperature data or weights and analysis of charge are unrecorded and observations on the physical characteristics of the slag are almost always lacking. With these points in mind, a test heat was made in which as complete as data possible on all the factors that affect the elimination of metalloids were obtained. THE TEST HEAT The test heat was made in a standard 100 ton stationary furnace at the Lackawanna Steel Co., Lackawanna, N. Y. on January 17, 1922. The Charge-Scrap.-The scrap consisted entirely of rail-heat butts, selected from a number of heats made, the week before the test. The average analysis of the scrap was calculated from the analysis of these heats-and from the weight of scrap from each heat. Pig Iron.-Two ladles of pig iron were used in the charge and two samples were taken from each ladle as it was poured into the furnace. These four samples were composited for the average pig-iron sample.

Jan 2, 1926

By A. G. Taylor, H. P. Ehrlinger, U. C. Tainton

FOR the last 15 years lead has been the standard material for anodes in electrolytic zinc production and it has been generally accepted that this lead should be as free as possible from impurities. Laistl says, "Next in importance to the purity of solution is the purity of the electrodes and tank lining material. The purest lead obtainable should be used for anodes." The same conclusion is expressed by Ingalls2 and by two German investigators who say that experiments have demonstrated that the purer the lead, the greater is its resistance to corrosion during electrolysis.3 Pure lead, however, while the best material hitherto available for anodes, is not entirely free from objection. The plain lead anode gradually disintegrates under electrolysis, so that the life of an anode, say 1/4 in. thick, is frequently not more than two years. Part of the lead from the anode finds its way to the cathode, lowering the purity of the deposited zinc and decreasing the hydrogen overvoltage. The rest of the lead that comes from the disintegration of the anode goes into the manganese dioxide which is precipitated in the cells, rendering unsaleable what might otherwise be a valuable by-product. Yet a further disadvantage of plain lead anodes comes from their tendency to bend or buckle during electrolysis, as a result of intercrystalline oxidation. This makes it necessary to use a fairly aide spacing between anode and cathode to avoid short circuits, and thus leads to a higher power consurnption than would otherwise be necessary. The power consumption is also affected by the high decomposition voltage at a lead peroxide surface.

Jan 1, 1929

By D. L. Albright, R. W. Kraft

A technique is described whereby the study of crystal perfection through the use of conventional X-ray rockite curves is extended to three dimerzsions. Specinzens of unidirectionally solidified eutec-tic alloy which consist of a nearly perfect parallel arrangement of alternating Platelets of Al and CuAl2, but which contain lamellar faults have been analyzed by this technique in conjunction with X-ray microscopy. Analysis of the data has shown that some rotational symmetry about the growth direction occurs, that small groups of lamellae between faults diffract as a unit, and that the misorientation caused by a fault is on the order of a degree of arc. A eutectic-grain can be defined as that portion of a eutectic specimen in which the crystallographic orientation of each phase AND the microscopic or met-allographic orientation of the phase particles have fixed angular relationships one to another. Eutectic-grains of the A1-CuA12 eutectic, which is a normal lamellar eutectic, have been grown by unidirectional solidification and identified as such.1-3 To a first approximation, a eutectic-grain in this system consists of two interpenetrating single crystals which are related to each other and to the lamellae themselves as follows:

Jan 1, 1962

By J. M. Locke

Bruckner's revolving cylinders for roasting ores, etc., are now used at a number of the mills in Colorado and New Mexico, for the purpose of roasting and chloridizing silver ores, with highly satisfactory results, even from those cylinders of small size, erected before the many improvements of recent date. AS examples of the larger improved cylinders, reference can be made to those erected at the Tennessee Reduction Works, Silver City, Grant County, New Mexico, and those which were built, in 1871, at the celebrated Caribou Silver Mill and Mines, Colorado, a mining enterprise which has proved so satisfactory as to have been lately sold to a Holland company for an enormous amount. These cylinders, as now constructed by Messrs. Lane & Bodley, of Cincinnati,,Ohio, are shown in Plate 111, in which Fig. I is an elevation in perspective, Fig. 2 a longitudinal, and Fig. 3 a transverse section. Fig. 4 is a sketch of a mill, with Bruckner's cylinder. The exterior of the cylinder is a shell of boiler iron, 12 feet long by 5 feet 6 inches in diameter. The ends are partially closed with similar material, leaving in the centre a circular opening about 2 feet in diameter, bounded by a flange projecting several inches. Upon one side is placed an opening closed by a hinged door. Upon the outside of the cylinder are bolted three bands, as shown in Fig. 1, in which the section of the first is square, and that of the third semi- . circular; the second, or middle band, is a strong spur gear. Passing through the cylinder are six pipes parallel to one another, in a plane at an angle of 15" to the axis of the cylinder; these pipes also lie in this plane at an angle of from 30" to 35' to the longitudinal .axis of the plane, as shown in Fig. 2, where the internal arrangement of the cylinder is seen, a perforated diaphragm being formed through part of the cylinder by means of perforated plates placed between