Search Documents

By Richard A. Arterburn

For many years hydrocyclones, commonly referred to as cyclones, have been extensively utilized in the classification of particles in comminution circuits. The practical range of classification for cyclones is 40 microns to 400 microns, with some remote applications as fine as 5 microns or as coarse as 1000 microns. Cyclones are used in both primary and secondary grinding circuits as well as regrind circuits. The information given in this chapter is intended to provide a method, at least for estimating purposes, of selecting the proper number and size of cyclones and to determine the proper level of operating variables. Generally, it is recommended that cyclone suppliers be consulted for sizing confirmation. Sow cyclone suppliers employ digital computers to aid in the sizing and selection of cyclones. CYCLONE DESCRIPTION AND BASIC OPERATION Figure 1 shows a cutaway view of a typical cyclone. During operation, the feed slurry enters the cyclone under pressure through the feed pipe into the top of the cylindrical feed chamber. This tangential entrance is accomplished by two types of design, as shown in Figure 2. Since the majority of research has been done with the involuted type, the graphs and relationships shown may not be strictly applicable to other designs. As the feed enters the chamber, a rotation of the slurry inside of the cyclone begins, causing centrifugal forces to accelerate the movement of the particles towards the outer wall. The particles migrate downward in a spiral pattern through the cylindrical section and into the conical section. At this point the smaller mass particles migrate toward the center and spiral upward and out through the vortex finder, discharging through the overflow pipe. This product, which contains the finer particles and the majority of the water, is termed the overflow and should be discharged at or near atmospheric pressure. The higher mss particles remain in a downward spiral path along the walls of the conical section and gradually exit through the apex orifice. This product is termed the underflow and also should be discharged at or near atmospheric pressure.

Jan 1, 1982

By Francis A. Pocock

The writer is continually asked, if this electricity:is all you claim for it, why do not the mines put it in and use it? The best answer was given by Mr. John Fox Tallis, in his paper read before the South Wales Institute of Engineers in 1888, namely, that the reasons are similar to those which have prevented the more general employment of other systems of haulage. Managers, as a rule, are " not experienced mechanical engineers; neither are they all versed in electrical engineering." It may be said that there are a number of " able and practical electrical engineers who could do the work; but those electrical engineers are not conversant with the practical routine of colliery work and are, therefore, placed at a disadvantage by not knowing the actual requirements of mining engineers, and the many little difficulties to be met and contended with in underground workings; and, until mining engineers have acquired the necessary knowledge and a confidence in electricity, it is only natural that they will continue to follow the beaten path." In the above remarks, Mr. Tallis has hit the nail on the head. In the face of the partial failure, financially, of the haulage-plant which the Union Electric Company of Philadelphia had set to work at Lykens Valley, Pa., an electric haulage-plant was installed near Scranton, Pa. The question was not whether electricity could do the work, but whether any electrical company knew enough about the practical difficulties to attack and overcome them. That point being settled, the remainder was easy. The contract for the Erie Colliery haulage-plant was signed in January, 1889. This colliery is owned by the Hillside Coal and Iron Company, Mr. Samuel Hines, President, and Captain W. A. May, Superintendent. The company has been using arc-lamps in its breakers for three years. It is the only company in the Lackawanna Valley which has had enterprise enough to do so. Consequently, it was acquainted

Jan 1, 1890

By Walter Showak

The published phase diagrams for the copper-zirconium system1,2 indicate that the solid solubility of zirconium in copper is not accurately known. Studies made on relatively impure alloys by Pogodin, Shumova, and Kugucheva3 yielded a maximum solubility value of 1 wt pct Zr at the eutectic temperature. Allibone and sykes5 reported that an as-cast 0.2 wt pct Zr alloy is single phase at room temperature. Limited results obtained by Raub and Enge14 indicated that zirconium solubility in copper is less than 0.13 wt pct Zr at 940°C. Tn 1960, on the basis of a microstructural examination of several copper-rich Cu-Zr alloys, saarivirta6 placed the maximum solubility of zirconium in copper at 0.15 wt pct at the eutectic temperature, 980°C. The present note describes results obtained during a re-investigation of the Cu-Zr system for the purpose of accurately establishing the solidus and solvus curves and the eutectic temperature in copper-rich alloys. High-purity copper (99.99 pet) and zirconium (99.64 pet) consolidated reactor grade sponge were used to prepare several alloys, containing up to 2 wt pct Zr, by induction melting in graphite crucibles in vacuum and chill casting into a split steel mold. The melting procedure consisted of first melting the copper charge and then adding the bulk zirconium wrapped in pure copper foil. Chemical analyses were made of both the cold-rolled alloy ingots after homogenization at 925°C for 450 hr in evacuated quartz capsules and of small specimens which had been used in the phase diagram studies. 'The carbon content of each alloy was also determined and was found to be less than 0.001 wt pct in every case. Metallographic and electrical resistivity measurements were used as the primary methods for this investigation, although some thermal analysis studies were also performed. Heat treatments of all the alloys were carried out with the specimens wrapped in molybdenum or alloy foil (of the same composition as the specimen) and sealed in quartz tubes either in vacuum or under a purified helium atmosphere. Following high-temperature anneals for long periods of time, slight depletion of zirconium from the specimen surface was observed. Therefore, careful preparation of samples for microscopic examination and chemical analysis of the samples themselves was necessary to check the composition of samples used in determining phase boundaries. Points on the solvus curve were determined on quenched specimens by both isothermal reaction after solution heat treatment at 950°C for 8 hr and by isothermal annealing of alloy specimens at successively higher temperatures for times ranging from 24 to 500 hr. Liquation studies for positioning of the solidus and eutectic temperatures were performed by holding a pre-

Jan 1, 1962

By C. H. Jr. Herty

The results of a study of the open-hearth process from the physicochemical view-point are given. This study includes experimentation in small laboratory furnaces and in standard 100-ton furnaces. The behavior of manganese, carbon, and phosphorus are quantitatively explained. The action of "residual" manganese is discussed with reference to its relation to iron oxide dissolved in the metal. The solubility of CO in steel and its relation to dissolved FeO and carbon is given. The equation for phosphorus elimination has been tested out on a 200-ton furnace and the results are given in the text. THE effect of temperature and slag composition on the elimination of metalloids in the basic open-hearth process has been qualitatively understood since the early days of steel making. The quantitative effect has, however, only recently been brought to attention. The effect of slag composition has received more attention than that of temperature, primarily because the range of finishing temperatures in the basic open-hearth process is small compared to the large variations found in the composition of the slag at different periods during the process, and to the variations occurring with the use of raw materials of different degrees of impurity. The effect of slag composition on the elimination of metalloids has been studied by Styri1 from the thermochemical standpoint. This method is open to serious errors, in that thermochemical data at 2900° F. are very inaccurate and in many cases completely lacking. Feild2 has calculated equilibrium constants from the rate at which the metalloids are eliminated. The effect of slag viscosity on rate of elimination will affect the constants calculated by this method. Whitely,3 Colcough4 and others have used slag compositions as the basis for calculation of constants by which the extent of elimination may be calculated.

Jan 2, 1926

By S. Weissmann, P. R. Swann, D. F. Wriedt

The sizes and density of precipitates in an intemally oxidized 0.19 wt pct Al-Ag single crystal have been determined by low-angle X-ray scattering and by transmission electron microscopy . The correlation in particle sizes measured by the two techniques is reasonably good. For an oxidizing temperature of 800°C the particles were found to INTERNAL oxidation of dilute alloys of aluminum in silver produces an oxide which has an excess of oxygen compared to Al2O3.' It is believed that the excess oxygen is an indication of the small sizes of the oxide particles. Depending upon the particular model chosen for the oxide structure, the size of the o-A1 particles can be calculated as a function of the oxygen-to-aluminum ratio. These calculations pre- have diameters in the range 30 to 140A, with a mean size of about 50.4 as observed by electron microscopy. At lower oxidizing temperatures, less than 600°C, no clearly resolved particles are formed, and it is suspected that if A1-0 clusters exist they must be exceedingly small, i.e., 10A or less in diameter. dicto that the particles would vary in size from 15 to 100A. This range of sizes is amenable to detection by both small-angle X-ray scattering and transmission electron microscopy. This paper compares the cluster sizes in such internally oxidized A1-Ag alloys determined by transmission electron microscopy and small-angle X-ray scattering. SPECIMEN PREPARATION Single crystals were prepared from 99.9999 pct Ag, obtained from Cominco Products, and 99.99 pct Al, obtained from Aluminum Co. of America. All melting operations were carried out in graphite molds under flowing purified hydrogen in a horizontal zone refiner. The silver was first degassed,

Jan 1, 1964

By W. F. Carew, H. D. Kessler, F. A. Crossley

AS part of a program on phase relationships and transformation processes of titanium alloy systems, the titanium-rich corner of the Ti-Mo-V system has been investigated. This region was surveyed primarily to supply information toward the development of a creep resistant, weldable alloy, with a minimum alloy content, for use in the 425° to 550 °C range. Specifically, the investigation was directed toward the development of a stable ß alloy with less total alloying additions than is found in the Ti-30 pet Mo alloy. A secondary objective was the development of a creep resistant, weldable a-ß alloy for application around 300°C. Molybdenum was selected as primary additive to titanium on the basis of an investigation1 which showed that the Ti-30 pet Mo alloy had promising elevated temperature tensile properties. Furthermore, aging studies1 showed no tendency for this

Jan 1, 1957

By P. W. Bakarian

PREVIOUS determinations1,2,3 of the texture of magnesium and its alloys have shown only slight variations in the principal features of the structure. This investigation presents pole figures for magnesium and two of its alloys, in which differences of some magnitude will be shown. Schmid and Wassermann have considered the texture of magnesium in analogy with that of zinc-also a hexagonal lattice. Whereas the zinc texture is said to be derived primarily through basal slip and secondarily through {102}† twinning, the {102} twinning is considered impossible at the later stages of the rolling in magnesium because of its smaller axial ratio. This state of affairs appears reasonable for pure magnesium, but for alloy textures the situation is more complex. A double orientation similar to that found in zinc has been reported by J. D. Hanawalt,4 and the addition of small amounts of calcium to magnesium and its alloys to produce a double texture was noted by J. C. McDonald.5 The pole figures of this investigation, using an improved X-ray technique, show these various textures. The dependence of directional properties of rolled sheet on modifications of texture is well recognized. Correlation of physical properties with existing texture should be even more significant if quantitative valuations are attached to the various areas on the pole figures. Such a quantitative technique is developed herein. EXPERIMENTAL METHOD Two alloys were used, besides high-purity magnesium. In each case, the metal was extruded to bars 32 in. thick and hot-rolled to a thickness of about 0.075 in. It had been established previously that such a reduction was more than sufficient to eliminate the extruded structure. The rolling proceeded in the same direction as that of the extrusion, without any cross rolling. The temperatures corresponded to normal commercial practice, averaging around 600°F. A unique method of preparing the sample was developed in this work. Instead of using a flat specimen, a stem of the metal was cut out of the rolled sheet in the desired direction (rolling direction) as shown in Fig. 2. From a sheet of 0.075 to 0.065-in. gauge, the stem was cut to a square cross section with a jeweler's saw, rounded with a file and polishing paper to a diameter of 0.060 in, and evenly etched in dilute hydrochloric acid to a diameter of 0.038 ± 0.001 in. In this way, a cylinder of the original sheet with its axis in the desired direction was produced. By using this type of specimen for the pin-point pictures, any variance in the absorption of the diffracted beam at the various angular settings of the specimen, was completely eliminated.*

Jan 1, 1941

By R. W. Raymond

THE Brüclrner roasting-cylinder is well known as an apparatus which has done good work in the desulphnrization, particularly of refractory silver ores, in the western districts of this country. A paper by Mr. J. M. Locke, of Cincinnati, describing the cylinders, as constructed by Messrs. Lane & Bodley, in that city, may be found at p. 295, vol. ii., of the Transactions of the Institute; and a paper by Mr. N. H. Cone, vol. iv., p. 226, gives an account of their operation in Colorado. The purpose of the present paper is to present an .improved construction, designed by Mr. Brückner. This is clearly shown in the accompanying plate, which scarcely needs explanation. It will be seen at once that this construction involves two cylinders, instead of one. Mr. Brückner thinks that three cylinders might be better yet, as securing an exact mechanical reproduction of the work of the well-known three-hearth Fortschaufelungsofen, the most perfect of the reverberatories in which delicate roasting is performed with hand-labor. THE APPARATUS. Erection of the Cylinders.—Although the cylinders may he put lip at any locality, or added to existing works, it is preferable, if possible, to choose the site on a hill sloping naturally, say about 30' or 33. Two excavations are made, one 8 to 12 feet higher up than the other; and each is protected by a wall with a batter of about 1 inch to the foot, to prevent slides of stone and earth. Each cylinder being 20 feet long and 7 feet in diameter, the total excavation should be 60 to 70 feet along the hill, and 15 to 25 feet wide. On each level a building is erected 35 feet long by 20 feet wide and 12 feet high, with the roof containing a ventilator against the hill. When both buildings are on the same level, there should preferably be a solid frame-work of very heavy timber, to carry the four rollers which bear the upper cylinder. The four rollers carrying the lower cylinder should preferably rest on two very heavy pieces of timber, strongly braced together and laid to their top in a foundation made of stone or brick and cement. Foundations are necessary only under each two opposite rollers, but they must be made carefully,

Jan 1, 1886

By H. O. Hofman, H. L. Norton

Zinc smelters in the central western States have established a very high standard of purity for blende-concentrates, viz., zinc 60, iron less than 3, and lead less than 1 per cent. The very low percentage of iron is made possible by the blende containing less than 0.5 per cent. of isomorphous iron sulphide and by the sparing occurrence of pyritic material in the large blende-deposits of southwestern Missouri and southeastern Kansas. The blende in these districts occurs in sub-carboniferous limestone, and is associated with chert, residual clay, cal-cite, pyrite or marcasite and bitumen. The different minerals are coarse and therefore readily separated by mechanical washing from the blende, with the exception of pyrite and marcasite, as blende has a specific gravity of from 3.9 to 4.1; marcasite, from 4.85 to 4.90; and pyrite, from 4.95 to 5.10. The common procedure of dressing the ores' is to crush in a breaker, size in a trommel with 0.5-in. holes, pass the over-size through roughing-rolls and then jig the ore, now reduced to 0.5 in. maximum size, in roughing multiple-sieve jigs. The products of these are waste-tailings, side-discharge coarse concentrates, side-discharge coarse middlings and bottom-discharge fine middlings. The coarse concentrates are sent to the market. The coarse middlings are crushed in middlings-rolls and brought back into the system by feeding into the main trommel. The fine middlings are cleaned upon finishing-jigs. Any pyrite or marcasite present follows the blende and increases the percent- +1MASSACHUSETTS INSTITUTE OF TECHNOLOGY, BOSTON, MASS.

Jan 1, 1905

By H. J. Struth

A glance into the immediate future of the refining industry, and a retrospective view of 1929, cannot fail to emphasize the need for effective measures of control of refinery still runs. With oil producers alert to the need for control of the crude supply, it has become more than ever necessary for refiners to complete the movement toward stabilization by concerted determination to maintain still run schedules within the limitations prescribed by the demand for gasoline. The outlook for continued growth in the demand for gasoline appears to be well sustained by a preliminary survey of requirements for 1930. In fact, it is apparent that the industry will be assured of a market for gasoline that will aggregate in volume at least 472,000,000 bbl. this year. This indicates a gain in total demand over 1929 of about 9 per cent. or about 4.6 per cent, less than the gain recorded during 1929 over 1928, which amounted to 13.6 per cent. Despite the indicated increase in gasoline demand this year, it is apparent that little, if any, more crude will be required than last year. This is shown in Table 1, presenting estimates of gasoline demand and probable crude requirements for 1930. Table 1.—Preliminary Survey of 1930 Gasoline and Crude Run Requirements Millions of Barrels Doniestic gasoline demand................................... 397 Foreign gasoline demand..................................... 75 Total indicated demand...................................... 472 Natural gasoline content..................................... 53 Net gasoline from crude...................................... 419 Imported gasoline........................................... 13 Net gasoline required from refineries.......................... 406 Indicated excess stock Dec. 31, 1929........................... 10 Maximum protluction required................................ 396" At 40 per cent. gasolitlc recovery, this represents a maximum crude converson of 990,000,000 bbl., or a daily average for the ycar 2,712,000 barrels. Year after year, the refining branch of the petroleum industry has been found guilty of running crude to stills greatly in excess of normal requirements, causing frequent periods of market depression. A review

Jan 1, 1930

By J. H. Frye, C. P. Sun

A Frimary substitutional solid solution is a solution that has the same crystalline structure as the solvent metal, and in which solute atoms have replaced, solvent atoms at random on the host lattice. This replacement usually results in an increase in hardness as measured by conventional penetration tests. The factors controlling this hardness increase have been investigated in some detail for copper and silver alloys.1-5 It has been shown that at least four factors are involved: (1) concentration of solute, (2) row of the periodic table from which the solute is taken, (3) increase in lattice parameter of the solvent produced by the solute, and (4) work-hardening produced by penetration of the hardness indenter.2,4 The last factor is of the utmost importance. An investigation of the available data2,4 leads to the conclusion that the solutes that produce large hardness increases in copper or silver do so principally because they increase the rate of work-hardening. Furthermore, it is doubtful whether any solute produces appreciable hardening in the absence of plastic deformation and hence work-hardening. Thus it is clear that an understanding of the effect of solutes on rate of work-hardening is essential to an understanding of the hardness of solid solutions. This effect of solutes is also important in forming operations such as rolling or deep drawing. The presence of elements that confer rapid rates of work-hardening will increase power consumption and may well decrease the amount of deformation possible between anneals. This paper is the report of an investigation of the factors that control rates of work-hardening in copper and silver solid solutions. The silver and copper alloys considered are those in which all solutes are from the B subgroups or second short period of the periodic table. Experience with hardness, with structure of alloys, and with electrical conductivity has proved that results of a fundamental nature are most likely to be obtained if alloys are made up on the basis of the positions of the constituent elements in the periodic table. In previous work, Meyer analysis data on high-purity copper and silver solid solutions were obtained through careful measurements with fully calibrated equipment and these data were corrected to correspond to a standard grain size. From these corrected Meyer analysis data rates of work-hardening have now been calculated. Calculation of Rates as Work- HARDENING The Meyer analyses, on which this study of rates of work-hardening is based, consisted in determining impression

Jan 1, 1944

By Theodore A. Blake

At the Chicago meeting of the Institute, May, 1884,I had the pleasure of announcing the introduction of a new machine for fine crushing, or The Blake multiple-jaw crusher, which, in combina tion with the ordinary Blake breaker, could be used in the reduc tion of ores or any hard and brittle substance to almost any degree of fineness. I am now able to give some practical results derived from its use on an extensive scale, on the gold ores of South Caro lina and the iron ores of Lake Champlain, together with some accurate and detailed statistics of the cost of crushing over one hundred thousand long tons of magnetic iron ores of the Chateaugay Ore and Iron Company at Lyon Mountain, Clinton County, N. Y., about thirty miles west of Plattsburgh. The construction of the multiple jaw-crusher, since the date of my first paper, is the same, except in the substitution of main swinging, instead of main sliding, or toggle jaw,—thus doing away with the upward thrust on the tension rods and the wear incident thereunto. (See Fig. 1.) It has also been found, in case of the fine crusher, that is, in machines of not over 4 inch width of opening, that the use of several small machines with a series of jaw openings, say 15 inches by 4 inch, is better than one large machine with a series of openings 24 by 4 inch, or 36 inches by 4 inch, as at first constructed. Many details of the method of holding in jaw-plates, etc., have been perfected. Without giving any details with respect to the different mills built upon the Blake 'system, let me state that, although it has proved possible to carry any hard and brittle material with crushers alone to a fineness such that all particles will pass a 30-mesh wire screen, still the economical limit of such crushing will be found somewhere between 14 and 20. If it is necessary to carry all the material to a fineness greater than this, the system must be supple

Jan 1, 1888

By Arthur F. Taggart, T. C. Fitt, A. W. Thomas

IT was noticed early by operators that high recoveries and flocculation of the sulphide minerals were closely correlated in agitation-froth flotation. Later, this readily visible flocculation was found almost invariably to be due to the binding together of the oiled sulphides by minute air bubbles, and is now known to be characteristic of pulps in which at least one of the mineral species is coated with an insoluble collecting oil. In 1930 it was reported1 that in differential flotation a correlation exists between Brownian movement of particles in the pulp and their nonfloatability, and that Brownian movement and dispersion are likewise correlated, whence it would appear to follow that dispersion of a mineral particle in a flotation pulp denotes a particle condition unfavorable to flotation. In 1934 it was postulated2 that Brownian movement, dispersion and nonfloatability all flow from the condition of the surface of the dispersed particles. It was also postulated at that time that the surfaces of dispersed particles are ionized, the ionized compound being a product of reaction between a component of the particle and a. component of the pulp, of a mass solubility of the general order of a fraction of a milligram to 15 to 20 mg. per liter. It was then further asserted, and has since been confirmed by Bankoff,3 that sulphides so conditioned with soluble collectors as to be floatable flocculate without the intervention of air bubbles as binding media. The present paper comprises an inquiry into the nature of the bound and counter ions in zinc sulphide dispersed by sodium arsenate. A part of its findings was mentioned in the 1934 paper above cited.2 The tests show that: I. When powdered granular zinc sulphide is immersed in aqueous solutions of sodium arsenate, arsenate ion is abstracted from solution and anchored to the solid surface, while sulphate and lower sulphoxy ions are concurrently displaced therefrom in substantially stoichiometric quantities. 2. The ion counterbalancing the anchored arsenate ion is zinc. 3. Dispersion and Brownian movement of zinc sulphide are concurrently maxima at an arsenate-ion concentration lying between 0.01 and 0.001-molar sodium arsenate. 4. Any condition or reaction that tends to remove the zinc arsenate coating from the zinc sulphide particles decreases dispersion and Brownian movement concurrently. EXPERIMENTAL Three samples of zinc sulphide were used. Lot I was C.P. zinc sulphide, washed well beyond absence of chloride, as shown by test with silver ion. Lot 2 was prepared by precipita-

Jan 1, 1943

By Duncan MacVichie

The iron fields described here are located in the Iron Springs and Pinto mining districts, Iron County, Utah. This region is in southwestern Utah, about 260 miles south from Salt Lake City, and is reached by the Los Angeles & Salt Lake railroad of the Union Pacific system. The iron fields lie at an elevation of 5500 to 7500 ft. above sea level, and are essentially desert in character. They are covered with a light growth of sage brush, piñon pine, and scattered cedar. Weather conditions are unusually favorable for all-year mining operations, the winters being mild with little or no snow; and the summers not excessively hot, the temperature rarely rising to 100 during the day, while the nights are invariably cool. The iron-ore bearing area extends from the Iron Springs district to the Iron Mountain mining district, being approximately 25 miles long in a northeast-southwest direction, and from 1 to 3 miles wide in a northwest-southeast direction. In the Iron Springs and Pinto mining districts, the ore occurs at various points around three sides of Granite Mountain and Iron Mountain. This is readily understood by reference to Figs. 1-4. These mountains are composed of andesite, which has been forced up through the surrounding sedimentary formation, in the form of laccoliths. An extensive report on the geology of these districts was made by Leith and Harder,' who state: The three dominating geological features of the district are three large andesite laccoliths which constitute the Three Peaks, Granite Mountain, and Iron Mountain; lying in a northeast-southwest line across the area in question. Three unconformable sedimentary series, aggregating 4000 ft. in thickness, outcrop in successive rings around these laccoliths, dipping outward asymmetrically, very steeply at the contact, less steeply farther away. Still farther from the laccoliths, lava-flows 2000 ft. thick rest in nearly horizontal attitudes on the tilted sedimentary rocks. These general relations are modified by faulting. All of the rock formations of the district are more or less covered on the middle and lower slopes by unconsolidated and partly consolidated erosion debris, both aqueous and subaerial, which spreads out on the lower ground to make the deserts.

Jan 1, 1927

By R. W. Raymond

THE question, what is the best proportion among weight, fall, and speed of stamps, is one which has not yet received thorough and systematic examination. In considering the economical application of stamping machinery, we meet, at the beginning, with serious difficulties in obtaining accurate data for comparison. The weight and fall of stamps vary as the shoes and dies wear out; and this may lead to a change of speed also. Moreover, defects in engines, boilers, or machinery for the transmission of power, may occasion serious losses, which cannot fairly be charged to the arrangements of the stamps proper. Again, the capacity of stamp-mills is directly dependent, in some degree, upon the nature and extent of discharge, fineness of screens, and other peculiarities of the battery. Finally, the hardness and tenacity of the rock crushed varies so much that comparisons between different localities cannot be implicitly trusted. The safest experiments are those made in the same mill, by changing first one and then another condition of working; but this is seldom possible for such conditions as weight and lift of stamps, and only within narrow limits for their speed. We may eliminate of friction, transmission, and generation of power, in the case of stamps, by measuring the power actually developed by their fall. Thus, the weight, multiplied into the fall in feet, and the number of drops per minute, gives us exactly the number of foot-pounds exerted by each stamp. Dividing by 33,000, the number of foot-pounds per minute in one-horse power, we have the horse-power per stamp, from which the effective power of the whole mill may be obtained. Dividing the amount of rock crushed daily by the effective horse-power, gives us the daily amount per horse-power ; and this is the best measure that can be obtained for the effectiveness of the stamps. A complete discussion of the subject would require us to determine the exact influence of the discharge, etc., and the exact resistance offered by different classes of rocks, for both of which points the data are wanting. Professor J. D. Hague, in the third volume of the United States Geological Exploration of the Fortieth Parallel, gives a valuable

By H. M. St. John

Like every present-day manufacturer, the brass foundryman is faced with the necessity of reducing the cost of his finished product without impairing its appearance or quality. He must use every economy that the progress of art and science puts at his disposal and should also be alert to profit by any peculiarity in his own situation or the nature of his product that may give him an exceptional advantage. Much can be accomplished by the adoption of labor-saving equipment and improved methods of melting, molding and handling. Control of pouring temperature, study of defective castings and their causes, laboratory control of molding sand and core mixtures, the use of less expensive alloys, all contribute to the desired end. Assuming that the composition of the alloy is already as inexpensive as the character of the casting will permit, still further savings can be made by the intelligent purchase and utilization of the metals needed to produce the desired analysis. Functions of Secondary and Virgin Metals in Casting Brass It is no longer a general assumption among foundrymen that quality castings must be made from an "all virgin" mix. If suitable secondary metals can be obtained more cheaply it is wasteful to use any larger proportion of virgin metal than is required to produce castings of the desired properties. To follow such a course, however, imposes upon the foundryman a heavier obligation than was formerly the case, to make sure by test and inspection that his castings really are of the desired quality. So long as he used the most expensive grades of metal and his melting practice was reasonably correct he was not obliged to give much thought to the quality of the metal in the castings. If he is to use secondary metals he must, in order to retain the confidence of his customer, examine these metals very carefully before use, exercise scrupulous control over his melting and pouring conditions and examine his castings closely. These statements apply more particularly to the jobbing foundry. The foundry department in a manufacturing plant is in a somewhat

Jan 1, 1930

By W. F. Hergert, L. H. Banning

Experimental production of Al-Si alloys, containing from 33 to 55 pct Al, by direct reduction of aluminum silicates in a three-phase arc furnace is described. Advantages of a smelting technique utilizing hogged wood waste as part of the reductant and for temperature control are discussed. WORK on the problem of producing aluminum by smelting has been in progress since the middle of the eighteenth century. Early work met with little success and in 1782 Lavoisier, an eminent French chemist, expressed the belief that alumina could not be reduced by carbon. It was almost a century later when the Cowles brothers developed a process for the production of aluminum alloys by reducing alumina coincident with the reduction of other metal oxides. In practice, the other metal oxide was usually copper. In 1907 it was first shown that alumina alone could be reduced by carbon at a temperature of 2200°C. The metal produced was volatilized and lost or recombined with the oxides of carbon formed in the reaction.' For a number of years after the Cowles brothers abandoned production of Cu-A1 alloys because their product was not commercially competitive with the aluminum produced by the Hall process, there was little interest in thermal reduction processes. After World War I interest in such processes was renewed and a number of patents were issued on processes for the production of A1-Si alloys.' , "he function of the silicon in these processes was the same as the function of the copper in the Cowles brothers process, namely, to prevent the reduced aluminum from recombining with the oxides of carbon and to promote absorption of the aluminum vapors set free at the high temperature required for the reduction reaction. The advantage of using silicon in place of copper for this function is that silicon has a higher boiling point (2600"C) than copper (2310"C) and its oxides, combined with aluminum oxides, occur in nature in almost unlimited quantities. No A1-Si alloys have been produced commercially in the United States, as far as is known. However, considerable experimental smelting of aluminum silicate materials has been done by the TVA at Wilson Dam, Ala.' The most extensive development and commercialization of the electrothermal production of A1-Si alloys took place in Germany before and during World War II.V he furnaces used in the

Jan 1, 1956

By V. R. Garfias

. EVEN before the arrival of Cortes in 1519, the history of Mexico was closely linked to that of its mineral production; the mining activities of the Aztecs being thus described by Clavigero, one of the early historians: In the mountains of Anahuac there abound in veins all kinds of metals, and infinite variety of other fossiliferous products. The Aztecs obtained gold from the countries of the Cohuijques, of the Mixtecas, of the Zapotecas and from various other places. They gathered that precious metal usually in grain, from the sands of the rivers, keeping a certain portion for the crown. They obtained silver from the mines of Taxco, of Tzumpango and others; however, this metal was not as esteemed by them as by other neighboring nations. They had two kinds of copper; one hard, which they used instead of iron to make sickles; lances and all kinds of rural and military instru-ments and another, soft, with which they made kettles, goblets and other receptacles. This metal abounds mainly in the province of Zacatula and in that of Cohuijques, which at present is in the kingdom of Michoacan. They obtained tin from the mines of Taxco and lead from those of Izmiquilpan, located in the country of the Otomies. From the tin they made money, and the lead, we know they sold in the market places, but we ignore the uses to which they applied it. They also had mines of iron in Tlaxcala, in Taxco and in other places; but they either had not discovered them, or did not know how to make use of the metal they contained. In Chilapa there were mines of mercury, and in other places there were mines of sulphur, alum, vitriol, cinnabar, cohre and of a white earth which they esteemed highly. As regards mercury and vitriol, we do not know of what use (they were to them; the other metals they used in paintings and dyes. There were then great abundance of amber and asphalt-bitu-men of Judea-on the coast of the seas and many cities of that territory paid tribute of one and the other to the kingdom of Mexico. They mounted the amber in gold, and it was only used as ornament and display by them. With the asphalt they made certain perfumes.

Jan 1, 1937

By Andrews Allen

THE large increase in the wages of mine workers makes it imperative that all factors tending to limit production per miner be eliminated, if possible. The trolley and storage-battery locomotive, mining machine, hoisting engine, mining system, etc. have increased the possible output per man. But this output is still limited by the capacity of the hoisting engine and cable and by the size of the mine car. The superiority of skip hoisting in metal mining is shown by its almost universal adoption. By varying the size of skip and the rope speed, any desired hoisting tonnage can be secured and, since only one kind of material is handled and breakage is unimportant, the loading of the skips can be easily and cheaply effected from bins into which the cars are dumped. The cars may then be designed to fit the conditions in the mine instead of being a compromise between hoisting and mining conditions, very likely suiting neither. In coal mines, the usual practice has been to hoist the car to the surface, either on platform or self-dumping cages. Of late years the number of skip-hoisting plants in coal mines has been rapidly increasing, but there is more or less inertia to overcome in establishing so radical a change in practice; also the earlier skip operations were not uniformly successful. As a result, it became evident that metal-mining practice would require radical modification before skip hoisting could be successfully used in coal mining.

Jan 2, 1921

By Clarence Zener

THE internal friction of nonferrous metals vibrating at low stress amplitudes has so far always been successfully interpreted in terms of inhomogeneities of one sort or another. Examples are the fluctuation of stress across a specimen vibrating transversely,1,2,3 the stress inhomogeneities due to the elastic anisotropy and partial random orientation of the individual crystallites,4,5 localized weak regions introduced by cold-working,6,7 grain boundaries and possibly twinning planes.8,9 Perfect single crystals are, by definition, homogeneous. Actual single crystals usually, perhaps always, contains some imperfections. The present investigation. was undertaken to determine whether the internal friction of single crystals may likewise be attributed to inhomogeneities. This study was made possible through the gift of a large single crystal of 70-30 alpha brass by H. L. Burghoff, of the Chase Brass and Copper Co. The specimen, ½ in. in diameter and 10 in. long, was similar to samples previously described by Mr. Burghoff.10 EXPERIMENTAL METHOD The experimental method used has previously been described in Institute papers.5,6,9 The measure of internal friction adopted here, 1/Q, is (1/p) X the logarithmic decrement, a measure used by some writers, and is also (1/2p) X the specific damping capacity, a measure used by other writers. In all measurements the stress level was kept so low that the measurements were independent of stress level. In all measurements in which the temperature was varied, observations were made as the specimen slowly cooled from its highest temperature. The specimen was vibrated transversely. Observations were made at the funda¬mental frequency and at the first overtone, of about 620 and 1710 cycles per second, respectively. No attempt was made to avoid acoustical losses. EXPERIMENTAL RESULTS The specimen was annealed for several hours at 450°C. The temperature dependence of the internal friction was then determined from room temperature to 400°C. As shown in Fig. 1, the internal friction increased by only a factor of 2 from room temperature to 300°C., then by a factor of l00 during the next 100° interval. These measurements are consistent with the view that the observed internal friction is the superposition of two distinct parts. One, dominant at room temperature, is nearly independent of temperature. This part may be accounted for by acoustical losses and by transverse thermal currents. It was not further investigated. The second part, when plotted in the manner of Fig. I, lies upon a straight line. Therefore it has a heat of activation H; i.e., it varies with temperature as Internal friction e~H/RT [I]

Jan 1, 1942