Search Documents

By C. S. Barrett, P. Coheur

AXnealing twins are common in the microstructure of copper that has been rolled and recrystallized. In such samples it follows that a twin relationship should exist between components of the re-crystallization texture,' and several examples of this have been reported. For example, twin relationships have been found in recrystallized electrolytic copper sheet, as indicated in Fig. I, from a paper by Coheur and Lejeune.2 In this pole figure the cube texture (100) [001] is indicated by the hollow squares in the lower half of the figure (the pole figure for 200 reflections) and in the upper, (III), part of the figure. The texture contains, in addition to this orientation, the first-order twins of it, shown in the figure by the filled triangles. This orientation relation has been suggested by others also, under certain annealing conditions,3'4 although pole figures have not been published to confirm it. Some orientations in recrystallized sheets are identical with their twins, because of the symmetry elements of the texture— this is true, for example, with the (113) [ZII] texture so commonly reported for brass—hence it appears impossible in such samples to decide whether the twin relationships result from twinning or merely from the symmetry of the deformation process. The present investigation of a commercial copper strip seems to yield an example in which annealing twins account unambiguously for the principal orientations present. It proves to be a case, also, for which the recrystallization texture cannot be viewed as derived from the deformation texture by a first or second-order twinning mechanism. Materials and Methods The samples investigated were of secondary copper (melted in belgium) to which 0.19 per cent iron had been added to raise the recrystallization temperature. How much the orientation characteristics of this metal can be ascribed to the iron content and how much to other impurities or to melting and pouring practice have not been investigated.* The rolling was done in one direction only, on a mill with rolls of about 20-cm diameter. A strip I. cm wide was reduced from 5 mm thickness to 0.05 mm by several cold passes at commercial speeds. The samples cut from this 99 per cent reduced strip were X-rayed throughout their entire thickness. A pole figure made soon after rolling and annealing was identical, within experimental error, with one that was made when a two-year interval occurred between rolling and annealing. X-ray patterns were made on a camera2 that traversed

Jan 1, 1947

By Lloyd R. Jackson

In the past 15 years there has been a great deal of interest in the fundamentals of plastic flow and rupture in metals and a number of papers have presented substantial advances toward a fundamental insight into the mechanism of these two processes. This paper is an appraisal of the present position with respect to the following: 1. The relative importance of shear and hydrostatic stresses in controlling the plastic flow of metals. 2. The relative importance of shear and hydrostatic stresses in determining the amount of flow before rupture in metals. 3. The use of generalized strains in determining the effect of plastic flow on the work-hardening of metals. FundamentalS Involved in Plastic Flow In attempting to devise a quantitative description of plastic flow in metals, it has been customary to assume that metals are homogeneous and isotropic. The fact that neither of these assumptions is correct complicates the experimental appraisal of relations developed. Nevertheless, as will be shown, metals are close enough '0 being isotropic and homogeneous so that considerable insight into the mechanism of plastic flow can be obtained. The assumptions of isotropy and homogeneity allow both the elastic and plastic behavior of metals to be described in terms of 12 variables—six being stress variables, and six being strain variables. From this viewpoint, it should be possible to represent the stress-strain relations in the plastic range for metals by a surface in 12 dimensions. One boundary of this surface would be the surface of transition from elastic to plastic behavior; the other would be the surface of rupture. These two surfaces would be joined by the surface of plastic flow. The shape of this composite surface would depend on the test temperature and speed of straining This paper is concerned only with results obtained at constant temperature and constant speed of straining. While such a representation is conceivable, the demonstration of such a surface would present almost insurmountable obstacles. The most fruitful simplification of this concept has been the recognition that the behavior of metals in the plastic region is primarily a result of shear stresses and strains. Based on this viewpoint, it is possible to utilize stress and strain invariants that are independent of hydrostatic components to define an effective stress and strain. In effect, this amounts to reducing the task of representing stresses and strains in 12 dimensions to one of representation in two dimensions. The two invariants (one for stresses and one for strains) that have received most attention are the following: q2 = ½[(Txx= - Tyy)2 + (Tyy - Tzz)2 + (Tzz - Txx)2 + 3(Txy2 + Tyz2 + 7xx2) [1]

Jan 1, 1947

By Richard M. Foose

Most of the roofing granules produced in Pennsylvania are made by two companies at three plants. The Advance Industrial Supply Co. has three quarries and a mill at Gladhill Station, in southern Adams County. The Funkhouser Company is actively engaged in mining, quarrying and milling at Charmian, about one mile west of Gladhill Station, and at Delta, in southern York County. These three plants produced approximately 100,000 short tons of granules in 1943. The production of rooling granules in 1937 for the whole country was only about 500,000 tons, generally indicating the large growth of the industry since that time. The fundamentals of producing roofing granules were discussed comprehensively by G. W. Josephson in a paper before the Industrial Minerals Division in October 1943 (TP 1725, this volume page 460). The purpose of this paper is to describe the actual methods of mining the rock and milling it to make roofing granules, as practiced by the three Pennsylvania plants. Mining and Milling Funkhouser Company (Delta) The Funkhouser Company, near Delta, in southern York County, Pennsylvania, operates three joined quarries and a mine in the Peach Bottom slate. The joined quarries extend 1200 ft. in a northeast-southwest direction along the strike of the slate cleavage and are about 200 ft. .wide. The working face is about 45 ft. high. The quarrying operation is rather simple: Ingersoll-Rand Jackhamers, I-in. and 1 1/4-in., with hollow drill steel, are used to undercut the quarry face with 10-ft. holes. The face is "blown" and allowed to slump on the quarry floor. Loaded by a Marion electric shovel into trucks, the shattered rock is taken to the primary crusher 2500 ft. away. In addition to the normal quarrying operations, a drift into the northeast wall of the middle quarry was begun about 1935, and has advanced about 2000 ft. since then. Rooms have been driven at angles to the drift along choice beds of slate. The drifts and rooms have a roof more than 35 ft. high and the main drift and rooms are all more than 40 ft. wide. There is no cribbing at any place in the mine. Several of the rooms were driven upward on a 5' slope and in some of them there was stop-ing. Ingersoll-Rand Jackhamers are used, and only wet drilling is practiced. When visited in January 1940, an electric shovel was operating at the head of the drift, scooping up the slate blasted out of the working face. This, too, is trucked to the primary crusher. Some of the better quality slate is saved for making slate shingles. The primary crusher, which is a No. 30 McCulley gyratory, receives the slate from the trucks and crushes it to about a-in. size (Fig. I). This product travels by a 30-in. belt conveyor to Niagara vibrating screens with 2-in. holes. The minus a-in. product moves to a storage silo by bucket

Jan 1, 1948

By Corliss R. Kinney

Since the first atomic bomb exploded over Japan, a great deal of speculation has been published about the use of atomic energy instead of coal for the production of power. Atomic energy, in time, may displace coal for this purpose, but atomic energy will not displace coal in supplying chemical raw materials to the rapidly expanding carbon-chemicals market. Modern civilization demands large quantities of carbon compounds and the logical source of many of these is coal. Consequently, many progressive operators are considering the possibilities of the utilization of coal as a chemical raw material as never before. Furthermore, the demand for clean, smokeless, and ashless fuels will continue to increase and the only way to handle coal under those conditions is to take it apart, just as crude petroleum is taken apart. One can readily imagine where the petroleum industry would be now if it had insisted on selling customers only crude oil, perhaps emulsified with a little salt water to correspond to the moisture and mineral matter in raw coal. The time seems to be coming at an accelerated Dace when mine operators will find that competing for a highly selective fuel market by producing a larger tonnage at smaller cost will be less profitable than to increase the value of a smaller tonnage many fold by producing something more valuable to industry and civilization than raw coal. For example, about 750,000 tons of carbon black selling for $50 to $60 per ton was produced in the United States in 1945. This tonnage is insignificant compared with the total production of coal in the United States, but a very tidy tonnage, together with the coal necessary to operate the process, for any mine operator fortunate enough to obtain a method of producing a better carbon black from coal. From the point of view of tonnage, the manufacture of coke of various kinds and its by-products is at present the most important source of carbon chemicals from coal. Nearly 20 per cent of the coal mined in this country is used for this purpose. A large proportion of the coke is used for the production of iron and steel, but even in this operation a considerable part of the coke is used for a chemical purpose; that is, the reduction of the ore to metallic iron. In addition, large quantities of coke are used in manufacturing many important products that find their way into the market. Possibilities of Acetylene One of the important chemicals manufactured from coke is calcium carbide, from which many products are made. One of these is acetylene. This hydrocarbon can also be manufactured from natural gas or from waste oil-refinery gas and these industries will probably offer competition for the manufacture of acetylene. Coke-oven gas can be used for making acetylene and should receive consideration

Jan 1, 1947

By W. M. Mobley

The coal industry in Alabama, centered in Birmingham, has pioneered coal-bene-ficiation practice in the United States. The nature of the coal seams and mining methods employed have necessitated use of equipment and methods best adapted to the local conditions. Although all of the 30 or more coal seams now being mined in the state receive beneficiation, only the three most important producers of coking coals, the Pratt, Mary Lee and Black Creek, are discussed in detail. Nature of the seams, washability characteristics and equipment used are given as examples of the extent of work and progress in this field. The coal seams in Alabama are relatively thin and pitching, making mining difficult and expensive. Most of them are characterized by thin partings of rock or shale in the seam itself, as well as laminations of bone and rash. Mechanical mining methods have increased the occlusions from roof and floor to such an extent that nearly all the coal mined in the state must receive some treatment before it can be put on the market. During the year ending Sept. 30, 1943,' 18,129,792 tons of coal were mined in the state and 14,364,177 tons, or 79.2 per cent, received treatment. Excluding from the total the 1,223,014 tons produced by small wagon mines and the hand-picked lump coal, the amount re- ceiving beneficiation would be more than 90.00 per cent. This is, by far, greater than in any other coal-producing state. The earliest record of coal beneficiation in Alabama was the installation in 1890 of an experimental Lurig washer by Alexander Cunningham, for the Sloss Iron and Steel Co. at its blast furnace in Birmingham.2 In 1894 the Jeffrey Manufacturing Co. introduced the English Robinson washer, a combination of a hydraulic classifier and centrifugal machine. Erskine Ramsay, who has contributed so much to the coal industry, saw its possibilities as well as its mechanical defects and soon had his inventive mind at work. He added a sludge tank of his own design, and many Robinson-Ramsay washers were installed in Alabama and other states. The Stewart jig appeared in 1900, followed by the Montgomery jig in 1910 and both have found extensive use. Increased interest in this field led to new designs, such as the American, Elmore, Burke and Faust. The first Baum-type Norton jig was operated in 1930 and within the last five years six large installations of this type have been made by the McNally-Pitts-burg, Jeffrey and Link-Belt Companies. Wet-washing tables were introduced in 1922 but not extensively used until recently. The two most popular types are the Deister-Overstrom and Deister Plat-O. The coal-cleaning equipment used in Alabama has been relatively simple, yet efficient, but as the amount of impurities in the raw coal has been increased by mechanical mining and labor costs have become higher, much interest has been shown in sand cones, froth flotation and

Jan 1, 1947

By H. R. Banks

Pondering the action of a ball mill employed to carry on comminution from the product of fine crushing to the point where flotation, cyanidation or other concentrating methods are applicable, one wonders where this machine had its origin. When Henry Wadsworth Longfellow reiterated the observation of that older poet Von Logau, and wrote "Tho' the mills of God grind slowly, yet they grind exceeding small," he probably visualized the type of mill that was employed in medieval times for the production of flour, and can therefore not be considered as having gained admittance to the fraternity of millmen, on behalf of either poet. He does, however, make it quite clear that the efficiency of even these Mills of Destiny was low, and to that extent voices a characteristic of fine-grinding equipment that has been the bugbear of all metallurgical engineers. Principle of Ball Mill The principle of the ball mill probably is traceable to the action along the coast line of oceans or lakes, or in the mountain streams. Wave action on rocks and pebbles, close to the shore line, gives the potential energy to the grinding media, which, in their rolling and tossing, break down the sands, and the resultant "pulp" carried out from the shore is classified and settles out in sizes ranging downward to extremely he mesh. Surely, these are the real mills of God. If we allow our minds to dwell on the total tonnage that has been handled in this way, adding to the sands and clays at present in existence those enormous tonnages of metamorphosed sedimentaries we sense the vast quantity of rock that has been so reduced. Is it not likely, therefore, that the answer to the beginnings of pebble milling, and eventually ball milling, came through the perception of this natural mill by one of our engineering forebears? Methods of Grinding The relatively low return of mechanical input to a ball mill, in terms of useful work accomplished, has always intrigued me immensely. The potential energy absorbed by a ball raised to a high point in its path is apparently released with a very small return in useful work. Is the ball mill the most desirable means of he grinding, or is there some other method through which we can recover a reasonable amount of the energy input in terms of useful work? Some years ago, on his retirement, H. W. Hardinge was questioned as to his thoughts on the trend of fine-grinding equipment. As I recall, his prophecy at that time was that the most likely field for improvement in grinding media would be toward a charge of flat disks with some mechanical scheme to cause them to slide over each other. Undoubtedly, Mr. Hardinge went through the usual experience of the muller and bucking board, the customary introduction of the budding millman to his calling. I have often wondered, but have never got beyond the wondering stage, as to the

Jan 1, 1947

By Warren E. Wilson

The transportation of solids in pipe lines is a matter of deep concern in many fields of engineering. Much experimental and theoretical work has been done in an effort to devise means of designing pipe lines that will satisfactorily transport given solid loads, but there remain many unanswered questions in this field. The present discussion will be confined to a rather narrow portion of this field and will endeavor to point out certain factors that may well be considered when comparing the relative economy of various installations. The data have been presented previously but a new interpretation was prompted by a suggestion in a paper by Professor O'Brien,' of the University of California, that the friction work per pound of dry material should be considered in determining the relative efficiency of various installations. This method of considering relative economy in various pipe lines leads to some rather unexpected conclusions, especially with reference to the economy of large pipe sizes. A previous suggestion by the writer concerning the economy of a rather peculiar type of installation is strengthened. It is not believed that the considerations set forth herein apply directly in the case of dredge lines, where economy is largely a matter of a high rate of pumping in order to reduce the unit overhead charge. However, it is believed that some value may be gained from these considerations in cases involving the disposal of a fixed amount of solids per unit time with a minimum expenditure of energy and at a low cost for replacement of worn pipes. Such situations are not uncommon in the disposal of mill tailings and the disposal of solids deposited from irrigation waters. It was found that data leading to general conclusions for various pipe sizes were not available but certain definite trends are indicated and methods of analyzing available data are presented in the hope that they may be of assistance in preparing engineering estimates on designs of pipe lines of the type described above. Energy Requirements Carrying out the idea contained in Professor O'Brien's paper concerning the method of computing energy required to transport solids, the following analysis leads to some rather interesting conclusions. Let us represent: Solids load in terms of mass per unit time by w Ratio of mass of suspended solids to total mass of mixture flowing by p Volume rate of flow of mixture by Q Length of pipe by L Slope of energy grade line by s Mass per unit volume of solids by m8. Mass per unit volume of liquid by mi Mass per unit volume of mixture by 11 We then have as an expression for the solids load: w = pqmm The work done per unit mass, p, on the mixture to move it along the pipe the

Jan 1, 1947

By R. H. Smith, A. C. Polk

The physical properties of the materials are listed, together with a short explanation of how this material binds the sand grains together without materially reducing the effective permeability of the sand. The chemical can be used in wells with bottom-hole temperatures ranging from 105°F to more than 350°F A description of the equipment required and the techniques used for applying these plastics to the wells is included. Introduction Recovering oil and gas from unconsoli-dated sand formations offers one of the most troublesome of all production problems. These sands generally present no particular trouble while drilling is in progress, but after the well has been completed and a pressure differential has been established across the face of the producing zone, the formation begins to L'slough," resulting in "sanding up" of the well. The term "sanding up" means that sufficient volumes of sand have moved into the well bore or casing to cause a serious reduction or complete halt of all flow of oil, water or gas. In rare cases a well may produce only a small amount of sand and still continue to flow or pump, the sand being carried to the surface in the fluid stream. However, in such instances, the result may be a costly repair bill due to the effect of the sand on surface and pumping equipment. The difficulty of producing petroleum from sands that are loosely cemented has long been recognized by petroleum engineers but only within the last few years has any new approach to the problem been undertaken. This involves the use of plastics that are capable of bonding the individual sand grains in place without materially reducing the effective permeability of a formation. The successful application of plastics for the consolidation of poorly cemented sands is relatively recent but now it is widely used in many of the more difficult areas on the Gulf Coast of Texas and Louisiana. This relatively new use of plastics1 in the oil fields has been preceded by much laboratory and field research on the use of various chemicals2,3 for solving numerous well-completion and work-over problems. Plastics now are being used successfully to control gas-oil and water-oil ratios,4'6 in zone isolation, the repair of casing leaks, the elimination of caving in cable-tool drilling wells6'7 and in the setting of linerss and casing.9 Sand-consolidating plastics, however, are basically different from all others in that they must not form an impervious seal. Field Practices The approach to the sanding-up problem usually has been the mechanical obstruction of the movement of the sand grains.

Jan 1, 1947

By H. L. Barr

THE following report covers the history of the development of the mine, present equipment, methods and costs of mining and milling. In addition, a description of the ore deposit is given with emphasis on the origin of the fractures, mode and types of ore occurrence, and mechanics of granite emplacement. An endeavor has been made to present a complete and accurate statement of the San Mauricio mine, the highest grade gold mine in the Philippine Islands. Credit is gratefully acknowledged to the mine staff for descriptions and details regarding their particular field of work. All analyses were made by Mr. T. A. DeVore, head chemist, San Mauricio Mining Co. Messrs. Edward Wisser, J. E. Fyfe, A. F. Skerl and W. B. Meek, geol-ogists, have contributed geologic information and ideas, for which thanks are extended. The Executive Committee of Marsman and Co., Inc., Managers of the Company, has kindly given permission for publication. Mr. J. B. Stapler, Division Manager, Marsman and Co., has had the courtesy to read the manuscript and to give critical and helpful suggestions.

Jan 1, 1940

By F. H. Allen, R. P. Roe

The performance history of a volumetric gas condensate reservoir is presented. Curves depict the pressure-production relation and illustrate the phace behavior of the reservoir fluid. This performance is compared to calculated performance. This Bacon Lime Reservoir was discovered in 1941 and has been produced to field separators and gas sales. Reservoir performance has been observed by periodic bottom hole pressure sur. veys and companion sample analysis of well effluents, in addition to gas and condensate production data. , The pressure-production history demonstrates that the reservoir has produced under volumetric control. The "retrograde" behavior of the reservoir fluid is illustrated by decreasing butanes-plus content of the well effluent, followed by revaporization as the reservoir pressure approaches abandonment. Calculated performance predictions are compared to actual performance and some discussion offered on apparent discrepancies. INTRODUCTION Since the late 1930's, many gas condensate reservoirs have been developed, the retrograde theory of phase behavior has been generally accepted, and a number of cycling programs have been initiated. Numerous technical papers have since appeared in the literature dealing with the theory and application of cycling the gas condensate reservoirs. Some cycling operations have now advanced to a stage where it is possible to determine performance characteristics to a fair degree of accuracy. Field performance data for gas condensate reservoirs operated by pressure depletion have not been so extensively reported in the literature, although their probable behavior has been discussed in explanation of the retrograde theory. It is the purpose of this paper to compare calculated theoretical reservoir performance with field observations and well stream analyze; which have been obtained throughout the practical producing life of a small volumetric gas condensate reservoir. The reservoir under study is the Bacon Lime Zone of a field located in East Texas. The Bacon Lime occurs in the Lower Glen Rose Formation of Cretaceous Age. This Bacon Lime Reservoir is encountered at an average depth of 7600 ft (7203 ft subsea elevation) and comprises approximately 3100 acres located on a structural high with 80 ft of productive closure. The producing formation consists of approximately 50 ft of dense crystalline fossiliferous dolomite of generally low permeability with typical wide variation in both permeability and porosity, the more permeable stringers measuring 30 to 40 millidarcys. The average porosity is extimated to be 10 per cent with a connate water saturation of approximately 30 per cent of the pore space. The reservoir temperature was found to be 220°F and the original pressure was 3691 psia at -7200 ft elevation. The re ervoir was discovered in November, 1.941, and is now essentially depleted, Throughout most of its productive life, from the standpoint of cumulative withdrawals, the reservoir has been produced by five wells. During its latter stages of depletion, 16 wells were completed in the Bacon Lime.

Jan 1, 1950

By H. Siebel, N. A. D. Parlee

MIZIKAR, Grace, and parlee' studied rates of absorption of oxygen in stagnant liquid silver in a new type of open-ended gas-liquid metal diffusion cell, where the capillary diameters used were 1.5, 2, and 3 mm. They reported that the rates appeared to be controlled by the rate of diffusion of oxygen atoms in liquid silver and they used their data to arrive at the following equation as a reasonably good representation of the diffusivity (D) of oxygen in liquid silver: D = (14.7)10-4 exp (-7100 ± 3200)/RT cm2/sec Since this type of diffusion cell offers a promising method of measuring diffusivities of gas atoms in liquid metals, the senior author of this note and his students are carrying on a critical examination of the method, and are attempting to improve and extend the technique. The research reported briefly here was designed to examine more carefully the earlier conclusion1 that the absorption rate is diffusion-controlled, and to find out whether the diameter of the cell could be greatly increased and thus extend the method to systems where gas solubilities and diffusion rates are much smaller than in the case of oxygen in silver. For the purpose of these experiments, the open-ended capillary cell used by Mizikar, Grace, and Parlee was replaced by a small cylindrical crucible (1 to 1.7 cm in diam) containing pure silver (to a depth of 1.3 to 3 cm) resting in the bottom of a closed-ended vertical quartz tube, with an evacuated quartz filler tube just above the crucible to reduce dead volume. The method of measuring the rate of absorption was otherwise very similar to that of Mizikar, Grace, and Parlee and all the same precautions were taken. A much smaller and shorter tube furnace was used for heating, but simi- lar precautions about temperature gradients were observed. This technique was nothing more than the application of a Sieverts apparatus to the measurement of rates of absorption in small crucibles of stagnant liquid silver. In each run the volume of gas absorbed (V) was plotted against the square root of time (vt) and apparent diffusivities were calculated from the slope of the line, as described by Mizikar, Grace, and parlee.' Care was taken to use only the data obtained during the early part of the total absorption period while the cell functioned as one of infinite depth. The results at 1000°C are summarized in Table I and Fig. 1. The following conclusions may be drawn: 1) Diffusion cells up to 1.7 cm in diam yield, within experimental error, the same values for the diffusivity of oxygen (D) as the capillary cells of 1.5, 2, and 3 mm in diam employed by Mizikar, Grace, and Parlee. Cell diameters as large as 1.7 cm are probably not desirable for the most precise work. Intermediate sizes, perhaps 0.5 cm, will be most practical. 2) All absorptions measured were consistent with a model where the rate is controlled by the diffusion of gas atoms in the metal. The fact that runs at absorption pressures ranging from 0.1 to 1 atm (at any one temperature) give

Jan 1, 1965

By -1ng. B. Stampa

Introduction The author investigates the technology available for mine flow reversibility by reversing the operation of the main fans. Air bypassing, reversed sense of impeller rotation, and blade angle overturning are indentified as the most important means of achieving the flow reversibility. The axial flow fan is studied in some detail and the important variables of fan capacity, pressure, and efficiency are compared. Although some references to rotor velocity vectors are made (Fig. 1) the subject is not presented in detail in order to stay within the paper's intent. Background Where applicable, the requirements of mine air reversibility are an important part of the overall mining operation and should be given proper attention during mine ventilation design. The need for preventing mine fires in intake shafts is the reason that, for a long time, it has been a requirement in the Eastern European countries to have the feature of flow reversibility built into all main mine ventilators. In West German coal mines, this requirement does not apply since higher priority is given to safety precautions. Some metal and mineral mines in the United States are required to have ventilation currents readily reversible in order to fight underground fires as stipulated by the Title 30, Mineral Resources, and by the mining laws of some states. From an equipment performance standpoint, assuming the validity of other flow technical data, the question of the ventilator flow reversibility is of ten related to the actual scenario of the begining of an emergency. Most of the time, the system operates within half of the design capacity only and assuming that the equivalent mine orifice is stable only a quarter of the design pressure must be produced by the fan in any event. For such an operating point, the effective gradient and energy losses can be disregarded since fire emergencies usually last for only a short period of time. Equipment Comparison Fig. 2 depicts a ventilation arrangement wherein the flow can be reversed through changing the functional position of the dampers (slideplate or blade type). Both axial or radial fans can be applied in this case. For the mine exhaust operation, slide plates (guillotines) I and I11 are opened while plates I1 and IV are closed. The flow thus encounters two reroutings, which due to the reverse ventilation flow cannot be equipped with proper sheet metal deflectors, and therefore large pressure losses result during the air reroute operation. When the intake operation is considered, the dampers I and I11 are closed and the pair I1 and IV is opened. For this arrangement, almost the same flow conditions exist as for the foregoing exhaust mode; however, one additional corner must be applied. Even if a highly efficient ventilator is used in one of the previously described systems, the additional pressure losses resulting from air rerouting plus those encountered between the planes "0" and "00" significantly affect the overall energy requirements. Illustrated in Table 1 are the relative component losses of even flows for evaluation of various detour arrangements. From the aerodynamics standpoint, when these components are being designed, serious consideration must be given to the individual levels of the pressure loss coefficient, 5. Should there be an increase in the sum of the loss coefficients due to the particular component selection such that, for example, the net change is 1.2; the resulting pressure to be produced by the fan can be calculated from:

Jan 1, 1981

By P. G. Winchell, R. J. Russell

The distribution of displacements of originally plane surfaces by an invariant-plane strain has been analyzed statistically. The displacement ratio (the magnitude of the displacement of a point originally a unit distance from the invariant plane) can be determined from an analysis either of tilts of random surfaces or of displacements of random scratches scribed on a randowz surface. In either case the mean of the tangent of the observed displacement angle is related to the displacement ratio, and the number of observations used in determining the mean is related to the confidence limits placed on the estimate of the displacement ratio. In estimating the effect of applied stress on a phase transformation whose displacement effects can be approximated as an invariant-plane strain,* the dis- placement ratio of the invariant-plane strain is of primary importance. Two procedures for determining such displacement ratios are considered here. In the tilt method the measured quantity is taken to be the angle through which a random polish plane is rotated by the invariant-plane strain. In the scratch method the measured quantity is taken to be the angle between the original direction of a random scratch in a random polish plane and the projection of its final direction in the polish plane. In order to obtain precise results from either of the methods, it is necessary to measure the relative volume change associated with the strain in a separate experiment. TILT METHOD A locally homogeneous invariant-plane strain, P, with displacement ratio, S, may be written&apos; where ; and < are unit vectors indicating the displacement direction and invariant-plane normal, respectively, as pictured in Fig. 1. Eq. [I] describes a uniaxial strain if the direction of displacement is parallel to the invariant-plane normal and a pure shear strain if the displacement direction is perpendicular to the invariant-plane normal. The original orientation of the random polish plane relative to the invariant plane and to the displacement direction is shown in Fig. 2. The angle 03 between < and u is related to the relative volume change, ?V/V, and to the displacement ratio by As a result of the invariant-plane strain, the polish plane is rotated about its intersection with the invariant plane by the angle y, which is always taken to be positive. The tangent of this angle in terms of the above parameters is

Jan 1, 1967

By R. J. Pearce, I. Whittle, J. J. Stobbs

The oxidation kinetics of UCu5 in carbon dioxide have been studied over the temperature range 350° to 850°C. At any one temperature, two successive parabolic rate constants are obtained. Up to 650°C, the temperature dependence of the reaction is snzall and the first parabolic rate constant is higher than the second. At temperatures of 690°C and above, there is a very marked temperature dependence and the second rate constant is the higher. Metallo-graphic examination has shown that attack proceeds via internal oxidation. THE oxidation behavior of the U-Cu intermetallic compound, UCu5, in carbon dioxide was briefly examined during investigations aimed at selecting oxidation-resistant uranium-alloy coatings.&apos; It was found that an extremely thick, coherent scale was formed coated at the scale-gas interface with a thin, apparently continuous layer of copper. A more detailed investigation of the oxidation of UCus has now been made. Previous published work2 has been limited to a brief examination of UCu5 in connection with the oxidation of a U-1 wt pct Cu alloy in carbon dioxide. No attempt was made to explain its behavior, but the work indicated that attack proceeded by intern oxidation, with the formation of a layer of copper on the surface of the specimen. EXPERIMENTAL UCus was prepared by arc melting the stoichio-metric amounts of high-purity copper* and uran-

Jan 1, 1965

By S. F. Urban, G. Derge

AT the time this investigation was initiated variations were observed in the quality of different heats of basic electric-furnace steels, although they had been made under purportedly similar conditions. This indicated that these variations were related to normally unobserved variations in the character of the bath, especially during the "refining" period. Although the slags used for this operation are commonly referred to as "reducing" slags, and are regarded as having a "deoxidizing" action on the bath, no reliable measurements of this action were available. It was decided, therefore, to study the behavior of oxygen in the metal for a large enough number of heats to learn its normal variations and to relate these variations to regularly observed conditions [f] operation. The most important general conclusion reached was that the time a heat is held under a reducing slag should be reduced to a minimum, which was about an hour and a half under the conditions studied. Beyond this time no observable beneficial effects are obtained from the reducing slags, insofar as oxygen and sulphur content of the bath are concerned. It is likely that added time may increase hydrogen content as well as heat costs. The oxygen content of the bath is never reduced below the amount in equilibrium with the carbon. Concurrently with this work, J. S. Marsh1 presented data that supplement and support many of the results of this paper. PROCEDURE The work was done in two different electric-furnace shops of the same plant. The selection of heats was made primarily with regard to the convenience of heat schedules. Companion slag and metal samples were taken just prior to slag-off and throughout the refining period for an initial set of 17 heats, and before slag-off and near tap for an additional 13 heats. Slag sampling presented no particular problem; a spoonful of slag was poured onto a metal plate and when sufficiently cool was sealed in an airtight container. Sampling the metal for oxygen presented a more complex problem. Because of the lack of previous experience in sampling electric-furnace baths, a number of methods were compared. Chilled Wedge Samples2 An unkilled metal sample is removed from tie furnace in a well-slagged carbometer spoon and poured immediately into a heavy copper mold designed to provide rapid freezing. Three different types of molds were used to determine the optimum for electric-furnace heats. The Big Wedge Mold (a) was a 4 by 4 by 4-in. split copper mold, yielding a wedge-shaped casting 1 in. wide, 1 ½ in. long, and ¼ in. maximum thickness, and was finally adopted as the most satisfactory design. The Long Wedge Mold (b) was a 2 by 2 by 5 ¼ -in. split copper mold, yielding a wedge-shaped casting 1 in. wide, 2 ¾ in. long, and ¼ in. maximum thickness. The Small Wedge Mold (c) was 2 by 2 by 4-in. split copper mold, yielding a wedge-shaped casting 1 in. wide, 1 ½ in. long, and ¼ in. maximum thickness.

Jan 1, 1947

By W. C. Krumbein

GEOLOGICAL problems are approached from a geometrical (space relations) viewpoint, a kinematical (time sequence) viewpoint, or a dynamical viewpoint. The first two require sound training in conventional geology and in field methods. The third approach requires a solid foundation of chemistry, physics, and mathematics. Modern training for geologists should include close integration of basic sciences with geological principles. INTRODUCTION Our knowledge of the earth has increased tremendously during the last half century. We know more about its surface configuration, the distribution of its natural resources, the procession of living forms that inhabited it in the past, the chemical composition of its oceans, the areal distribution of its surface rocks, the movements of its atmosphere, and so on. Not only do we know more facts about the earth, but we have a better understanding of the processes that take place on and within it, such as the nature of earthquakes, the thermodynamics of the atmosphere, the chemical equilibria involved in the formation of igneous rocks, the mechanics of stream flow, the dynamics of the earth&apos;s origin, and so on. Many sciences contributed to the sum total of this knowledge, including such established disciplines as geology, geography, physics, chemistry, astronomy, biology. Out of this accumulation of new knowledge grew also a group of new sciences, such as seismology, oceanography, meteorology, volcanology, hydrology. Collectively these latter are known as the geophysical and geochemical sciences, and to a large extent they began as branches of geology. Until the turn of the century, for example, the study of earthquakes (seismology) was a part of geology, although as early as 1846 Mallet, a physicist, had suggested that the subject could be investigated by elastic-wave theory. Comparatively little progress was made along these lines until the seismograph was developed near the turn of the century; since then, additional earthquake data have accumulated rapidly, but more important, the interpretation of these data essentially has kept pace with their accumulation. In similar fashion, meteorology was generally considered a branch of geology as recently as one or two decades ago. Considerable progress had been made in such aspects as weather forecasting, but the science dates its recent rapid rise from the year 1911, when Bjerknes first applied the principles of dynamics to the analysis of air masses. The rapid development of such disciplines as oceanography, volcanology and hydrology was due in part to the application of principles of chemical equilibrium, of dynamics, and of thermodynamics to earth problems, by men who were essentially physicists or chemists by training. The last half century, therefore, and particularly the last two decades, saw the influx of numerous chemists and physicists into the realm of the earth sciences. In the meantime the main body of geology itself showed a marked growth, and

Jan 1, 1941

By B. W. Vallat

The Newport mine, located at Ironwood, gogebic county, Mich., on the Gogebic iron-range, is owned and operated by the Newport Mining Co., for the mining of iron-ore. I. GEOLOGY. The general geology of the gogebic range has been determined and recorded at different times by well-known geologists,&apos; and their work will be referred to briefly in connection with the local conditions in the mine. The strike of the formation across this property is about 15" north of east. The general dip is 68" to the north. At the base of the formation on the aouth lies the granite. Looking north, at right angles to the strike of the formation, we have the foot-wall of quartz-slates and quartzite about 400 ft. wide; the iron-formation about 800 ft. wide, and the hanging-mall of black slates. The iron-formation is composed of banded jasper and quartzite together with iron oxide and concentrations of iron-ore. In character the ore iu a soft red hematite, with occasional masses of hard blue "steel ore." The formation is crossed in many places by diorite dikes, which cut through at various angles, the larger or main dikes dipping into the foot-wall in a SE. direction at angles varying from 15" to 30°, while numerous small dikes occur which strike through the formation in a vertical plane and at approximately right angles to the main dikes. There are various theories concerning these dikes, especially as to the time of their origin with relation to the ore-deposition. The commonly-accepted theory is that the dikes were there first, but there are some who contend that they were formed

Jan 1, 1912

By Nicholas J. Grant, Noboru Komatsu

Electron-micrographic studies and hardness tests were made of an internally oxidized dispersion-strengthened Cu-12 vol pct SiO2 alloy follozuing longtime annealing at elevated temperatures. The rate of coarsening of SiO2 particles and the relationship between hardness and interpavticle spacing were Dispersion -strengthened alloys exhibit a remarkable stability of structure and properties at elevated temperatures compared with conventional alloys; nevertheless, when they are exposed to high measured. The rate of coarsening of SiO2 particles is controlled by the decomposition of SiO, rather than by the diffusion rates of silicon or oxygen through the copper matrix. The mechanism of coarsening was also studied by using a diffusion-couple technique. temperatures, weakening takes place as a result of coarsening of the dispersed phase. The theoretical treatment of the coarsening of dispersed phases has been treated by Greenwood,1 wagner,, and others3 by considering the interfacial energy of dispersions and the diffusion of solute atoms. Recently, experimental work on the coarsening of relatively insoluble, finely dispersed cobalt particles in copper was reported by Livingston,4 and on aluminum oxide in nickel by Dromsky, Lenel, and Ansell;5 according to these investigations, the rate

Jan 1, 1964

By E. C. Truesdale, R. K. Waring

The Research Division of The New Jersey Zinc Company (of Pa.) has conducted, over a period of years, numerous tests of the reducibility of various zinc ores and the reactivity of various kinds of coal, using a number of different experimental methods. Most of these tests have involved the reduction of mixtures of ore and coal. In such cases the following simultaneous reactions are believed to be mainly responsible for the production of zinc, as was shown by Bodenstein1 some years ago: ZnO+ CO = Zn + CO2 [1] C + CO2 = 2 CO [2] Each of these reactions is dependent upon the other for the supply of CO and CO2 , respectively, and the over-all rate of formation of zinc vapor will be determined by the slower of these two reactions. An analogous pair of reactions sometimes of importance is: ZnO + H2 = Zn + H2 O [31 C + H2O = CO + Ha [4] While it is possible to obtain an indication of the relative reducibility of various ores, or of a fine versus a coarse ore, by testing them with a given coal, and while coal reactivities may be measured in a corresponding manner, a more direct determination of relative reaction rates is possible by carrying out the desired reactions, such as I and 2, separately and under reproducible conditions. It is one purpose of this paper to present some of the results that have been obtained by the latter method. C. G. Maier2 discusses the relative rates of reactions I and 2 and concludes that while at relatively low temperatures reaction I is faster than reaction 2, this difference becomes less with increasing temperatures, although at smelting temperatures reaction I is still the faster. He also says (p. 48), "At temperatures . . . between IIOO° and I3oo°C., . . . the zinc oxide reduction reaction is intrinsically more rapid than its physical limitations; that is, it is limited by gas diffusion rates." In the course of numerous reactivity tests involving the separate use of reactions and I and 2, we have obtained data that show by direct experiment, we believe for the first time, the correctness of Maier&apos;s statements concerning these reactions. We also include data on the relative rate of reaction 3, involving reduction by hydrogen. Finally, some interesting results obtained by carrying out the reduction of a zinc ore-coal briquet in streaming atmospheres of nitrogen, carbon monoxide and hydrogen, respectively, are presented. *

Jan 1, 1943

By B. W. Frazier

IN the numbers of the Engineering and Mining Journal of June 27th and July 11th, 1874, there appeared some very complete statistics of the working of some anthracite blast-furnaces belonging to a large establishment in this country, followed by calculations of the heat requirements of the furnaces, similar to those which have been made for European furnaces by Mr. I. Lowthian Bell, Prof. Gruner, Prof. Akerman and others. To the author of these valuable papers, Mr. John A. Church, of New York, the thanks of American iron metallurgists are due for this attempt (the first, to my knowledge at least), to attack systematically and scientifically the problem of economy of fuel in our anthracite blast-furnaces, by applying the formulas obtained from European practice and from the experiments of European metallurgists, to the determination of the amounts and the modes of distribution of the heat production and absorption in our furnaces. In order to facilitate a comparison of the results thus obtained for the anthracite furnaces in question with those obtained for the best types of European coke furnaces, I have reduced to the same standard of heat units (the product of the ton and the degree Centigrade), and placed side by side, the calculations of the heat requirements of one of the furnaces of the Clarence works, as given by Mr. Bell, of a furnace at Pouzin, on the banks of the Rhone, given by Prof. Gruner, and of the anthracite furnaces for 1869-73, as given -by Mr. Church. Table I shows the different conditions of working of the three furnaces, of which Table II gives the respective heat requirements. I have made this latter table in such a manner as to give for each furnace its heat requirements, both according to the views of Mr. Bell and those of Prof. Gruner. Mr. Bell assumes that all the carbonic acid produced by the decomposition of the carbonate of lime of the charge, is reduced to carbonic oxide by contact with solid carbon ; also, that the carbon of the pig iron is a portion of that deposited in the ore in the upper part of the furnace, by the dissociation of carbonic oxide. Prof. Gruner, on the other hand, assumes that all the carbonic acid of the carbonates of the charge escapes unreduced, and that the carbon deposited in the upper part of the furnace, by the dissocia¬tion of carbonic oxide, is again converted into carbonic oxide or

Jan 1, 1875