Search Documents

By J. H. Slater

There is nothing particularly new about the use of sinter in a blast-furnace burden. For many years flue dust has been sintered at the various blast-furnace plants to put it in a form that could be recharged to the furnace with some assurance that it would stay in the second time. This paper is not a compilation of scientific data but only an attempt to give our experience with sinter. There are some unexplained discrepancies in the tests given here, such as the flue dust produced and iron tonnages, but the results given are the results that were obtained. Sinter is not the cure-all for blast-furnace problems. A good coke is still the most important factor in good furnace operation. However, good sinter is a big help. As flue dust is produced under varying operating conditions and fluctuates greatly in carbon content, it is difficult to produce from flue dust alone a uniform sinter, which will give satisfactory blast-furnace results. Sinter made from flue dust alone will change in character with every carbon variation. Almost invariably flue dust contains carbon in excess of the amount necessary to make good sinter, and this excess must be burned out. This, of course, necessitates reduction of the speed of the sintering machine and thus a decrease in tonnage. An alternative is to dilute with a carbon-free material to use up the excess carbon. High-carbon material when sintered results in a very dense, undesirable product, since the excess heat melts the charge into a hard, nonporous mass, and tends to form refractory silicates. At the Republic Steel plant in Cleveland, there had existed since 1924 a continuous-type sintering machine having 224 sq. in. of grate-bar area, capable of producing 9 to 11 tons of sinter per hour from flue dust. Under a former management, it was the practice to sinter only the flue dust from the blast furnaces, no attempt being made to recover the gas-washer sludge. As the dust was limited, the plant operated only part time. In other words, there was a sintering plant representing considerable investment, with good facilities for screening and preparation of raw materials, and flue dust available for only part-time operation. The sinter produced was costly and not a very desirable product. The first step was to install equipment for the recovery of the gas-washer sludge. This was done in the form of two large thickeners and a filter, which have proved very satisfactory. It was then decided to screen out the minus 3/8-in. fines from the Mesabi ores, mix them with flue dust and coke breeze when necessary, and operate the plant at full capacity. The tonnage increased to 18 tons per hour and the product was much improved. Sintering costs fell and the product was a preferred blast-furnace material, which on an iron unit cost compared very favorably with good Mesabi ores. On the average, 40 per cent flue dust and 60 per cent fine ore was being used. The oversize from the ore screening also became a preferred product for the

Jan 1, 1941

By Basil B. Zavoico

The World War I1 spread to Russia on June 22, 1941, when the German Armies began their invasion. The Soviet industries, which were already engaged in a tremendous armament program, further accelerated the flow of munitions, and equipment and supplies for all purposes not directly military were either entirely eliminated or reduced to an absolute minimum. With the occupation by German armies of the Dniepr and Kharkov industrial regions, this trend was necessarily further accentuated. The oil industry of Russia, in consequence, was left to rely more and more upon itself, its own very limited manufacturing facilities, extensive repair shops and probably much used equipment out of order stacked in the warehouses. All evidence available to date points to the fact that the new situation not only did not affect the production either quantitatively or qualitatively, but, on the contrary, caused a larger flow of much needed fuels to the country's war machine, primarily by renaissance of both management and labor. The oil industry of the Soviet Union, left to depend entirely upon itself for equip ment and supplies, and even for new workers and technicians to replace those called into the services, did and is still doing a good and effective job. Since it could not hope for new equipment and parts and could not blame any other industry for the delays in delivery, it dragged out old machines from storage and repaired them in its own machine shops. Often such stored and used equipment was but slightly defective, waiting for some small part from factories in Central Russia, plants that now were either in German hands or entirely converted to the manufacture of munitions. More particularly, instead of the pipe that could not be taken to the Caucasus from Central Russia, casing reclaimed from abandoned or submarginal wells was used, or pipe from the abandoned or but slightly used pipe lines; and this practice is being continued even now on a large scale, to create an ample reserve for the duration of the conflict. Indirectly such a development was even an improvement on pre-war days, when many wells about to be completed had to wait for weeks, even months, for the arrival of new pipe, all blame then being placed outside of the industry on the factories in Central Russia. For the purpose of reclaiming equipment and pipe still usable, special crews were organized. The war also caused much quicker adaptation of certain American practices and introduction of many emergency measures, such as: removal of derricks upon completion of wells and the use of drilling equipment mounted on skids for rapid transfer from location to location—both of these practices, while standard in the U.S.A., being new in Russia; installation of simplified surface pumping units; substitution of wooden bearings in the surface pump equipment; completion of wells in the Ural-Volga district, where formations are hard and tight throughout the sedimentary column, without either casing or

Jan 1, 1942

By Holbrook G. Botset

Experiments performed in this laboratory on the flow of gas-liquid mixtures through unconsolidated sands have been described and discussed in an earlier paper.4 In these earlier experiments a definite relationship was found between the liquid saturation of a sand and its permeability to the liquid or gas phase. Furthermore, the nature of the sand, the permeabilities of the sands over a range between 17 and 260 darcies, appeared to have a negligible effect upon the saturation-permeability relation. Likewise experiments indicated that the viscosity of the liquid, or the substitution of an immiscible liquid for the gas phase, had only a very slight effect on the permeability-saturation relation. This conclusion has since been definitely confirmed by the experiments of M. C. Leverett3 on the flow of oil and water through unconsolidated sands. The sands used by Leverett were of very low permeability (between 6.8 and 1.04 darcies), while the oil-water viscosity ratio varied between 90 and 0.057. Since the sands that constitute petroleum reservoirs are largely consolidated, although of widely varying degrees of consolidation, it was desirable to extend the experiments on gas-liquid mixtures to consolidated sand. In the study of consolidated sands additional variables are involved, but for the initial experiments the only new variable to be introduced was the cementing material. Experimental Procedure A comparatively limited assortment of sandstones was available for the selection of the experimental material. Of these, the Nichols buff sandstone appeared to be most suitable. It gives no visual evidence of any bedding planes, it has a firm structure, permitting easy handling, and its permeability is about 0.5 darcy. Its only disadvantage is the fact that it contains an appreciable amount of ferric oxide which, for experiments involving water, will hydrate and reduce the permeability. This

Jan 1, 1940

By Alfred H. Hesse, Edwin T. Myskowski

The development by the U. S. Bureau of Mines of a process for purifying manganese by electrolysis has stimulated interest in manganese alloys. While recent publications have shown some alloys of manganese and copper to possess rather unusual properties, none have included information on tensile properties, which have an important bearing on the usefulness of the alloys. Manganese-copper alloys can be heat-treated, since the single phases that exist at high temperatures may be retained by quenching. According to Persson,1 when quenched alloys containing from about 30 to nearly IOO per cent manganese are reheated, alpha manganese is precipitated (Fig. I). Calculations based on Persson's X-ray data indicate that this decomposi-tion is accompanied by a change in volume of as much as ; per cent. The reason that this large volume change has not been noted probably is the slow rate at which equilibrium is reached by these alloys. In an investigation on hardening by cold-work and heat-treatment, Dean and Anderson3 found that quenched alloys increase in hardness with manganese content and that high-manganese alloys harden very slowly with cold-work, while high-copper alloys harden much more rapidly. Heat-treatment has little effect on manganese-copper alloys containing less than 40 per cent Mn, and affects those alloys containing more than 40 per cent in accordance with their manganese content and heat-treating temperature. Dean and Anderson4 also found that cold-work increased electrical resistance of alloys containing from 50 to 80 per cent Mn, and that heat-treatment of alloys containing from 40 to 96 per cent Mn altered the electrical resistance considerably. Dean, Anderson and Potter6 have shown that the high vibration damping capacity that characterizes manganese-copper alloys containing 40 to go per cent Mn is affected by cold-work and heat-treatments. Highest vibration damping capacity at low stresses was obtained by heating for 2 hr. at 450°C. (842°F.) after quenching from solution temperatures. Preparalion of Alloys.—The alloys for these tests were melted in a 17-lb. basic-lined high-frequency induction furnace using electrolytic manganese, grade A ingot copper and a 70-30 CU-Mn master alloy (69.80 per cent Cu, 0.12 Fe, 0.04 Si, 0.006 S, 0.07 C, balance Mn). The manganese was heated slowly to expel excess dissolved gases and melted before the addition of copper. No fluxes or covers were used. The melts were cast in tapered iron molds and the ingots were reduced go per cent when forged to 1/2-in. rounds. These rods were given 2-hr. solution treatments at temperatures that depended upon the composition (Table I). Tensile Tests.—The tensile specimens, 0.313-in. diameter (1.25-in. gauge length),

Jan 1, 1942

By E. C. Houston, H. S. Rankin

Olivine is considered a valuable potential source of metallic magnesium in the chloride electrolytic process. Treatment of olivine with hydrochloric acid can be carried out under conditions that prevent the formation of gelatinous silicic acid, which would inhibit the reaction by forming a covering around the ore particles. It is our hypothesis that the formation of gelatinous silicic acid is avoided by the dehydrating action of the magnesium chloride, which takes up water to form a series of hydrates and leaves the silicic acid in granular condition. Leaching serves to separate the magnesium chloride from the silicic acid and unattacked ore, which can be treated with fresh acid in successive steps until extraction is essentially complete. The leach solution can be i purified by the addition of caustic magnesia and the precipitated impurities removed by decantation or filtration. The resulting magnesium chloride contains: Fe, less than 0.001 Per cent; Mn, 0.012 ; per cent; Ni, none. Chlorination† of olivine has two major defects: (1) a large part of the chlorine goes to form silicon and iron chlorides, (2) the anhydrous magnesium chloride is held by absorption in the finely divided silica. SupplY It is well known that olivine, a silicate of magnesium and iron, is present in large amounts in several localities in the United States. The largest deposits occur in the southeast and on the Pacific Coast.' The southeastern deposits were surveyed by Lewis2 in 1896 and by Hunter3 in the period 1933-1940 It is estimated that high-grade olivine, conveniently located with regard to transportation and power, is present in excess of 230 million tons above local drainage level in western North Carolina and north Georgia. Previous Technical Work In the past few years, olivine has attracted considerable attention in the refractory field. In the chemical processing industry, however, it has long been thought axiomatic that the cost of processing silicates is an economic barrier to their utilization, especially where more reactive minerals, such as carbonates, oxides or salts, are available. This attitude is not entirely justified in connection with olivine. unlike most silicates, olivine is readily attacked by acids, chlorine and other reagents without resorting to fusion to break down the silicate structure. Olivine has been suggested as a raw material for making epsom salt by roasting with pyrites.4 Other processes include acid treatment6 and digestion with calcium chloride.6 Recently a small plant was built near Webster, N. C., for making epsom salt from olivine by treatment with sulphuric acid. This plant is now in commercial operation, producing approximately two tons per day. Olivine is also receiving attention from the fertilizer industry as an inexpensive source of soluble magnesium.

Jan 1, 1942

by their overdogmatic picture of geology and their resulting drastic oversimplification and idealization of geologic features. I am in hearty disagreement with the recommendation that geophysics should be done by cooperative work between a geologist and a geophysi-cist. That arrangement would be comparable to doing petrography by having a physicist at the microscope and a geologist sitting by his side. The interpretation of the geological significance of geophysical data can be done efficiently only by a physicist who has become also a good geologist or by a geologist who is also a good geophysicist. Less Well-trained Men The rank and file, composing perhaps two-thirds of the personnel of exploratory geophysics, is not, and should not be, composed of highly trained men. The routine, stereotyped character of the work and the impossibility of promotion of more than a few from these lower ranks even under the best circumstances justify companies in filling the bulk of these rank and file positions with men having only a bachelor's degree at the most. There can be a wide range of training for such positions, although certain lines of study are preferred for certain kinds of work, and different employers have different preferences. For work in gravitational and magnetic prospecting, first preference will be for men having geological training and second for men with civil engineering training. In seismic work, men with geological training are preferred by some employers for computers; physicists, electrical engineers and all whose technical education has covered radio circuits are preferred for the other technical positions. Collegiate training in geophysical prospecting brings no preference and by many employers is given a slightly inferior rating. One large company seldom hires men who have just graduated with a major in geophysical prospecting. This prejudice is based on the reasoning that much of what is learned in college is obsolete or obsolescent, that most of the techniques learned in college will have to be unlearned, because different from those used by the employing company, and that in the long run additional courses in basic physics, mathematics and geology are of more value to a man than the courses on geophysical prospecting. DISCUSSION [This discussion refers to the five papers beginning on page 23 and ending on page 74.1 L. W. Blau,* Houston, Texas.—I have had some rather sad experiences with forecasting. For example, I could not foresee 10 years ago my present occupation, and I do not profess to be able to look ahead 10 years and tell anyone what he will be doing then. Referring to the point raised in the discussion, I do not know, for example, what the price of oil will be 10 years from now. If an appreciable number of

Jan 1, 1940

By Tell Ertl

THE Piceance Creek Basin in northwestern Colorado is believed to contain the richest large deposit of oil shale in North America. The major portion, about 1650 sq miles, is bounded by the White River on the north, the Grand Hogback, which runs from Meeker to Rifle, on the east, the Colorado River to the south, and the drainage basin of Salt and Douglas Creeks on the west. The Basin is a plateau 7000 to 9000 ft high, composed of 3000 ft of the Green River series of Eocene age and surrounded by a steep escarpment of 1000 to 3000 ft. From the escarpment the beds dip gently toward the center. Although oil shale is found in all members of the Green River series, the rich thick beds are found chiefly in the Parachute Creek member. This is normally capped by 100 to 200 ft of the Evacuation Creek, the youngest member of the Green River series. Actually the Piceance Creek Basin oil shale is not a shale, nor does it contain oil. It is magnesium marlstone holding solid organic matter capable of being broken down by heat into gases, some of which can be condensed into oil. The marlstone is resilient nonporous rock, difficult to sample by pick or hammer and moil. Many companies and individuals prospected the Colorado oil shale shortly after the first World War,' see Fig. 1, but because of the discovery of large quantities of petroleum in the late 1920's in Cali- fornia, Oklahoma, and East Texas, interest in oil shale development waned and did not revive until World War 11. In 1944 the writer, employed by the Bureau of Mines, prospected the high grade oil shale in numerous places along the southern outcrop of the Piceance Creek Basin. Several channel samples about 100 ft in length were cut, see Fig. 2. An eight-man crew needed a week to cut a satisfactory channel 80 ft long in the cliff face. The Phillips Petroleum Co., the Union Oil Co. of California and others also prospected the oil shale outcrop. In 1945 the Bureau of Mines initiated a core drilling program for the purpose of obtaining accurate samples from the Piceance Creek Basin. The U. S. Geological Survey set up a program for the geological study of the Basin that is still going on." Until the end of 1951 a total of 31 holes was drilled for core with diamond drills, and, in addition, cuttings through the oil shale have been obtained from 4 gas wells drilled by standard rotary oil well rigs. The Bureau of Mines drilled 12 of the holes, the Union Oil Company of California 8, the Standard Oil Company of California 6, the Sun Oil Company 3,

Jan 1, 1953

By Max C. Eastman, V. H. Wilhelm

California had a record year in production and drilling activity, but the results have not been sufficient to keep up with the enormous increase in demand due to war activity. During the year, 164 dry wildcats were drilled, 80 dry wells in proved areas, 31 gas wells, and 1158 successful oil-well completions for a total of 1433 wells, compared with a total of 765 in 1942. With new discoveries of only 20,000,000 and production of 283,000,000 bbl. for the year, total reserves of California oil have decreased more than 250,000,000 bbl. However, revised estimates of the reserves of old fields indicate an increase in the state's reserves of I00,000,000 barrels. The completion of 1158 wells has served only to maintain the maximum efficient daily rate of production at 800,000 barrels. There is evidence in many fields that oil is being withdrawn too rapidly to obtain the maximum recovery, and more rapidly than is conducive to good production practice. Statistics for 1943 as compared with I942 are shown in the table in the next column, Supply and Demand Steadily mounting needs of the military forces and increased industrial consumption raised total demand for all petroleum products on the Pacific Coast to 914,000 bbl. daily in 1943. That all-time record demand was 149,ooo bbl. daily higher than in 1942 and 214,000 bbl. daily above 1941 demand. Despite restrictions due to shortages of critical material, crude-oil production was boosted from 680,000 bbl. daily in 1942 to 779,000 bbl. daily in 1943, the highest level in 15 years. However, the new crude supply plus natural gasoline production and imports from other states totaled only 840,000 bbl. daily, leaving a deficiency between supply and demand of 74,000 bbl. daily. That shortage had to be made up by withdrawals from inventories, which had been steadily depleted during the previous four years. Aboveground reserves, which totaled 159,574,000 bbl. on Jan. I, 1939, were down to ~8.000,000, bbl. at the end of 1943. Significantly enough, the greater part of that decrease occurred during the last six months of I9437 when more than 23,000,000 bbl. was taken from inventories of both crude and products. Although the size of total inventories on Dec. 31, 1943 might appear substantial, about 65 per

Jan 1, 1944

By David R. Mitchell

The mineral pyrite (or marcasite) occurs in coal beds as balls, lenses, veinlets and bands. Several million tons are wasted annually on the refuse dumps from coal mining and coal-preparation activities. Sporadic attempts have been made in the United States to recover this pyrite for manufacture of sulphuric acid but only a few plants have succeeded in recovering it on a commercial scale. Several chemical companies in the East became concerned about supplies of pyrite early in 1943, but by late summer of that year the situation had eased. If for no other reason than national security and self-sufficiency during wartime, methods of recovering pyrite from coal-mine refuse should be worked out and made available to coal-mine operators who are potential producers of pyrite. Eastern sulphuric-acid plants are particularly likely to have their sources of raw material blocked by war conditions, so that special studies to determine where supplies of pyrite can be obtained for these plants from inland sources are desirable. Davis's1 summarization of conditions during World War I gives the following facts: During those years, the shortage of pyrite became acute. Shipments of hand-picked pyrite were made from a number of coal mines in Illinois, Indiana, western Kentucky, Ohio and Pennsylvania. A mechanical concentrating plant for sepa- rating pyrite from picking-table refuse was built at Danville, Ill., and operated for several years, and a small pyrite-concen-trating plant treating washery refuse near Gillespie, Ill., operated for several months in 1918. The Consolidation Coal Co. of Fairmont, W. Va., constructed and operated a sulphuric-acid plant using pyrite recovered from coal-mine refuse. The U. S. Bureau of Mines during 1917-1919 made a comprehensive survey of pyrite-production possibilities from coal mines and estimated that there was a potential yearly production of 435.000 tons from Ohio and Pennsylvania and 928,000 tons from Kansas, Missouri, Iowa, Illinois, and Indiana mines. This estimate included only mines that could produce one per cent or more of their coal production as pyrite containing a minimum of 40 per cent sulphur. PyRite Production According to the Minerals Yearbook,2 approximately 660,000 long tons of pyrite was produced in the United States in 1941, with an average sulphur content of 42 per cent. The average value f.o.b. mines was $3.09 per long ton. Spanish pyrite, 48 per cent sulphur minimum, was quoted at 12 cents a unit c.i.f. U. S. ports, equal to $5.76 a ton for shipments of minimum sulphur content. Most of the pyrite produced in the United States is obtained as a by-product in the dressing of copper and zinc ores. Metal mines in the East making pyrite concentrate for the market or use in company-operated sulphuric-acid plants

Jan 1, 1944

By H. F. Yancey, M. R. Geer, Franklin T. Davis

Coke with low phosphorus content is required by some of the electrometallurgical and chemical plants recently attracted to the Pacific Northwest by the hydroelectric power available from Bonneville and Grand Coulee dams. Shipping such coke into the area from eastern points involves a high freight charge, and during wartime consumes precious rail and ship-bottom space, so it is highly desirable to produce coke from the coking coals of Washington to meet the requirements of these industries. Although coke has been made from Washington coals since 1884, little has been known about their phosphorus contents or about the extent to which phosphorus could be reduced by cleaning, An investigation was undertaken, therefore, to determine the manner in which phosphorus occurs in the coking coals of Washington and its amenability to removal by ordinary coal-washing methods. Previous Work Phosphorus is a deleterious element in coke used for numerous metallurgical processes, including the production of pig iron, yet comparatively little published information is available on the occurrence and elimination of phosphorus in any of the coals of this country. A variation from 0.009 to 0.062 per cent phosphorus in various horizons of the Pittsburgh bed in the Connellsville region of Pennsylania has been reported,' and a reduction in phosphorus content from 0.020 per cent in the raw coal to 0.018 per cent in the washed coal was obtained in washing coal from the same bed in the Pittsburgh area;2 the latter figures represent average analyses for a year's operation of the washery on about 800,000 tons of coal. A reduction in phosphorus content from 0.018 to 0.011 per cent in washing coal from the Pittsburgh bed at another washery was observed, and the same report provides data on the phosphorus reduction obtained by separating 10 other coals on a bath of 1.35 specific gravity.3 European investigators have been especially active in correlating phosphorus content with petrographic analysis; fusain and durain generally contain the highest percentage of phosphorus, but this relationship is not universal.4 Some of these investigators have found that phosphorus is removed in the coal-washing process,5 but others have observed that the clean coal contained as much or even more phosphorus than the raw coal.'

Jan 1, 1944

By A. M. Hall

Sulphur, even in small amounts, may often be harmful to nickel and high-nickel alloys, causing impairment of mechanical strength and destruction of malleability and ductility, as shown by Merica and Waltenberg.l,2 It may act either in the form of nonmetallic inclusions produced in the liquid state during furnacing or as reaction products resulting from its diffusion into the solid metal. In recognizing the action of this element, ability to identify its various forms by means of the microscope is often of considerable importance, especially when direct quantitative methods are inapplicable. Of the sulphur compounds associated with nickel and high-nickel alloys, the sulphides that may be found in malleable nickel, Monelt and Inconel are an important group. These sulphides were investi- gated by metallographic methods in order to provide descriptive data by which to identify them. The nominal compositions of malleable nickel, Monel and Inconel are given in Table I. The term "sulphide" is employed here in a very general sense, to designate a substance in which sulphur and one or more metallic elements are combined. The term includes any combinations of compounds and solid solutions. Method of Investigation Three groups of small laboratory melts were made, one group to represent each of the three types of alloy under investigation. Within each group, a number of ingots with a sufficient variety of chemical analyses were prepared so that the effect of each of the elements entering the complete commercial alloy could be isolated and observed. In most cases, to facilitate metallographic study by exaggerating the number and size of the resulting sulphides, somewhat greater amounts of the minor elements were added than are present in the commercial alloys. Likewise, considerably more sulphur was added than is normal, but not enough to complicate the system. Transverse sections were cut at a point one third of the distance from the butt to the head of each ingot, polished and examined with an inverted stage metallo-graph equipped with a combination polar -izing-analyzing vertical illuminator. The light source was a tungsten-mercury vapor arc lamp.

Jan 1, 1943

By Basil B. Zavoico

The symposium on production for the year 1942 contains no papers on the foreign situation except those on Argentina and Mexico. It has always been the policy of officers in charge of the symposium to refrain from publishing information that might possibly injure national or private interests. At the close of the war we hope again to publish full and accurate records of production abroad. Excerpts From Circular to Authors In order to facilitate interpretation of the data in this chapter, we print the following excerpts from the Circular to Authors. The field is the unit in this tabulation. In cases of fields extending across State boundaries, such as Rodessa, it is suggested that each State author treat the section of the field in his State as a unit, and by a footnote indicate that the field extends into an adjacent State. Each space in Table I may represent one of four possibilities; either it is not applicable to the particular field, or the proper entry is not determinable, or the proper entry may be determinable but is not determinable from data available to the author, or the proper entry is determinable. When spaces are not applicable, leave blank; in spaces where the proper entries are determinable but not determinable from data available to the author, please insert y; in spaces where the proper entries are determinable by the author, make such entries. y implies a Rope that in some future year a definite figure will be available. The entry of a zero is a positive declaration, and it is an important declaration where it is in order. Inability to determine precisely the correct entry for a particular space should not lead the author to insert merely y. Contributions of great value may be made by the author in many cases where entries are not subject to precise determination. In such cases the author should use his good judgment and make the best entry possible under the circumstances. For many spaces the correct entries represent the opinion of the author (for example, "Area Proved") and in such cases the entry need not be hedged to such extent as when the quantities are definite yet can be ascertained only approximately by the author. In cases under definite headings but where figures are only approximate, the author may use x. It is thought that the nearest whole numbers are sufficiently accurate for our purposes except as to percentage of sulphur in oil. If an author desires to report any other figures to tenths, he may do so. The quantity of gas produced should include, where possible, gas sold or otherwise marketed, and gas blown into the air, burned as flares or otherwise wasted. Segregation of these figures would be interesting if the authors can make such segregation. In any event, the figures should represent as nearly as possible the total quantity of gas removed from the reservoir. Under the columns on "Depth," the average depth to the top of the productive zones and to the bottom of the productive wells, when subtracted, should give the approximate thickness of the productive zone. For fields where this is not true because of unusually high dip or for some other reasons, it is suggested that the authors indicate in their text the approximate average thickness of the productive zone.

Jan 1, 1943

By William H. Spice

The year 1942 in the South Central Texas area was marked by a sharp curtailment of exploratory drilling as compared with the past several years. In the 33 counties that compose this district, 17 of which are nonproducing counties, only 51 exploratory wells were drilled during the year 1942. This compares with 118 exploratory wells drilled during 1941, or a decrease of more than 50 per cent. At the end of the year 10 active exploratory wells were drilling in this area, as against 19 being drilled at the end of 1941. Of the exploratory wells drilled, two brought in oil wells and were new field discoveries and one was a gas well extending a recently discovered shallow gas area in the western part of the district. This compares with five new oil fields, one new . gas field and two extension wells drilled in 1941. Both new field discoveries were small and in areas outside of the general trend of the main producing horizon of the district in Edwards limestone: One new field, the Imogene, in Atascosa County, is a deep Edwards limestone prospect at 7500 ft., and the other new field, the Poth, in Wilson County, is a sSEa110w Wilcox (Eocene) prospect at 4000 ft. Subsequent drilling in each field to the end of I942 has proved disappointing. There were no new discoveries along the old Balcones fault-line trend, although 35 of the exploratory wells were drilled in counties along this trend. Approximately 38 wells were drilled in or adjacent to the proven fields of the district, of which 18 were oil wells, 2 were gas wells and 17 were dry holes. The district produced 6,186,178 bbl. of oil during 1942, which was a 7 per cent decrease under production for 1941. Approximately 4,961,000 bbl. of this total production, a slight increase over 1941, was produced by the four Edwards-limestone fields, Luling, Branyon, Salt Flat and Darst Creek, and the rest of the production came from the other 42 active fields in the district. During the year, 20 new producing wells were completed and 221 wells were abandoned in the producing fields. This alarming excess rate of abandonment~ over completions will be further reflected undoubtedly by a further decreased rate of 1943 production under 1942. Two active fields in the district in which more than one producing well was completed during the year were Bee Creek and Washburn. The majority of exploratory work in the district was confined to areas along the Wilcox trend, with a certain amount in progress along the deeper Edwards limestone trend. The successful completion of sevemi wells in the Washburn field from multiple sands in the Lower Wilcor (Eocene) has stimulated exploratory work along this trend, while the completion of a small well in the Imogene field from the Edwards limestone at 7500 ft. has renewed interest in this horizon at depths greater than generally are producing in the district. New Fields ounty. ble Oil and Refining Company's No. I

Jan 1, 1943

By Paul A. Schafer

BaLatoc mine, the principal gold-producing mine in the Philippines, is 10 miles southeast of Baguio, in the Cordillera Central of northern Luzon.' The region is a deeply dissected plateau, ranging in altitude from 3000 to 5000 ft. above sea level. The rocks consist chiefly of granodiorite, diorite, and remnants of metamorphosed sediments, cut by dikes of andesite porphyry and quartz-diorite porphyry. All are intruded by a volcanic breccia plug, oval in horizontal section, about 3200 ft. long and 2300 ft. wide, which is the north central part of the mineralized area. Three main vein systems have been developed (Fig. I): 96, 231 and 364, which strike about N.70°E. and dip 50° to 90°S. Each system is a braided zone consisting of many individual components. They are disturbed by a series of premineral faults or shear zones striking about N.4s°E. Twelve of these produce important effects on the persistence, character, and quality of veins. From west to. east the faults are named (after claims): Hog, Big Gun, Bull, Pine, Lolita, Bar No. I, Bar No. 2, Curt, Sun, Helen, Itoe, and Frog. They are early breaks formed prior to the N.70°E. vein fractures. Mineralization occurs on them but, with several prominent exceptions, they are too low grade to mine. A number of northwesterly striking faults complete the structural pattern. Although they are relatively abundant, the effect on the veins is so small that they do not present any problems in mining or development. All of these faults that have been observed are later than the N.70°E. veins and offset them to the left. Northeast Faults The early northeast faults* are notably continuous in spite of their small displacements, 20 to 100 ft. Frequently they appear so weak that their importance is masked and their identity clouded. The gouge along any of these faults may vary from exceedingly weak at one point to very strong at another point only a short distance away. In other words, the amount of gouge depends on the changes of attitude of the fault plane, and is no indication of the extent of the movement. Places where walls are spread apart are filled with gouge squeezed from tight places. Also, mineralization sometimes obscures fault gouges by replacement. The mineralization of northeast faults has produced several important ore bodies; namely, 231 west on On fault and 96 vein on the same fault. To a smaller extent, Lolita, Curt, Bull, Bar NO. I, and Sun

Jan 1, 1949

By Wilson D. Michell

The Magma copper vein trends east-west, dips 70" south, and cuts through a 6000-ft thickness of limestones, quartzites,. shale, diabase, and schist. The vein is itself a fault with a horizontal offset of 500 ft on the formation contacts in the two walls. There are two principal faults of large displacement and numerous smaller steep and flat faults that complicate the prediction of ore occurrence. A study of the geology, its systematic recording to facitliate ready reference, and graphic methods of interpretation of mineralization have aided the exploration, development, 2nd mining of the ore. In making predictions of the distribution of mineable ore bodies and their shape in critical areas, studies are made of "mineralization contours" and "mineralization trends," which are developed on a longitudinal section of the vein from variations in the concentration of the combined base metal content as shown by assays of available openings in the mine. Introduction This paper describes an example of geological work applied directly to mining and exploration problems in a deep vein deposit, and it is presented as being of interest especially to those engaged in working more or less similar veins. In 1944 to 1945 the writer spent a year as assistant to J. K. Gustafson in a thorough geological examination of the Magma mine. Much of the writer's subsequent independent work described in the present paper had its inception in ideas originated by Gustafson during that examination. Objectives of Geological Work at Magma Mine The objectives of geological work at Magma, as at operating vein mines of a similar nature, can be summarized as follows: 1. Direct assistance to the mining department by means of predictions as to the size, shape, grade, and location of ore bodies; by solution of fault problems and irregularities in the veins; by prepara-?ion of detailed ore-reserve estimates in specific areas; by keeping a complete record of the geology and assay results in the mine; and by guiding development work. In short, geology can aid in the realization of the prime purpose of the mining department, which is that of producing the greatest amount of ore in the most economical and expeditious manner possible. 2. Guidance for exploration, especially diamond drilling, in undeveloped areas of the mine. 3. Contributions to the understanding of the general geology of the deposit and its regional setting, including ore genesis, structure, and mineral relationships. Magma Ore Deposit The east-west trending Magma vein, dipping about 70" south, cuts through a 6000-ft thickness of concordant limestones, quartzites, shale, diabase, and schist, named in descending order. These

Jan 1, 1949

By Donald C. Branford

The place of geophysics in the curriculum of a college or an engineering school has been much discussed. There is uncertainty as to whether the graduate may be called a "geological geophysicist" or a "geophysical geologist." Some have used the term "geophysical engineer." The question of the specialized undergraduate curriculum versus a general undergraduate training in the parent sciences with the addition of cultural electives has been and is still being argued. The literature during the past Io years shows that there are two rather definite schools of thought on this subject. The prospective employer, engaged in active geophysical exploration, visualizes the graduate in terms of the routine work he will do in the field. The school administrator, grounded in many years of tradition in the cultural type of education, visualizes the graduate in terms of his position in a political and cultural society as well as in his work as a professional geophysicist. Both are right and both wrong. A third school of thought, that of the student himself, has been almost totally ignored. It would seem best, for the purpose of this paper, to treat these various points and allied material separately, and then to integrate the conclusions as a set of conditions that should be fulfilled as far as possible in the ideal curriculum. At the end the relationship of our findings to the curriculum that has been tentatively adopted at the University of Pittsburgh will be considered. Divisions in Definition or Field of Geophysics Geophysics is that field of science in which geological and earth problems are solved with the use of physical and chemical techniques. Altogether too much attention has been paid to the artificial separation in this science of the commercial applications from the so-called "pure" or academic geophysics. The only real difference in the two types of work is one of scale of operations. In the commercial field the scale is large in terms of fmancial backing, immediate economic importance, and speed of operations. In the academic field the scale is large in terms of breadth of interests, in eventual economic importance, and length of time allowable for theoretical investigations. In exploration work the scale is small in terms of dimensions, since the methods are applicable only to the outer 20,000 ft. or SO of the earth's crust. In academic work, the student is not pressed for results of immediate economic importance, and therefore can afford to spend more time on problems that seem unimportant at the time. In the sense of background knowledge of the parent sciences necessary to the geophysicist, no essential difference can be found. Physics, chemistry, geology, and mathematics together, and in their proper proportionate amounts, form the matrix from which geophysical ideas and methods may spring.

Jan 1, 1946

By Helmut Thielsch

During the last three decades a great many arguments have been presented on the subject of "mosaicJ' or "blockJJ structures of metals. Apparently because of insufficient evidence, the "block-structure" theories have never been widely understood among the physical metallurgists in this country, and most investigators among the few that have tried to demonstrate the existence of such an inner strutture Of crystals or grains have failed to recognize also the existence of a lamellar structure. Moreover, little thought has been given to justify the existence of such "lamellar" or "mosaic-block" structures on a theoretical basis. Since properties such as Plasticity; ferro-magnetism, hardness, diffusion, and others may be explained by structural faults in the lattice network of the crystals: the great importance of a more detailed knowledge of the structure within crystals or grains becomes now evident. Because Of the vast extent of the field Of submicroscopic structures, it shall be the purpose Of this paper only to review the more important of the results obtained by other investigators, especially in Germany, where a great deal of attention has been given to mosaic structure during the last three years. The origin of this mosaic patternt and effects of cold reduction and recrystallization will be shown in further studies later on. Imperfections in Crystals The many terms used in the literature to denote structural types of crystals are often not clearly defined. To clear up some of the confusion, the meaning of the more important terms will be given here. ideal, or perfect without any structural imperfections are called "ideal crystals,,or ''Perfect'' crystals,n meaning a Homogeneous interior structure of atoms, ions or molecules, as the case may be. In other words, at every point in the interior of the crystal exactly the same orientation of the crystallographic axes of the coordinate system would exist. The Surface of such a body, if etched with an appropriate etching reagent, would reflect light with perfect uniformity. Crystals of this type are almost nonexistent. Real Crystals.—L'Real crystals"' may contain various types of structural defects, which can be classified into: (I) lineage structure, (2) mosaic-block structure, (3) lamellar structure. The inhomogeneities many,in these groups mean that the orientation of the crystallographic aies will not be the same at every point within the interior of a crystal (or grain of a poly crystalline body). 'Perjecl Real Crystals.—The term "perfect real crystals " is generally used to describe crystals with minute structural or thermo-dynamical inhomogeneities. The former

Jan 1, 1946

By Charles R. L. Oder, Howard W. Miller

Approximately 5000 tons of zinc ore a day was mined during 1943 in the Mascot-Jefferson City district in East Tennessee. This ore came from the Kingsport formation, a part of the Knox dolomite, of Ordovician age. The Kings-port is composed of 350 to 400 ft. of limestone and dolomite. Thin cherts, sandy layers and shales are numerous. Frequently, the limestones are altered to crystalline dolomite. The Kingsport is divisible into four main lithologic zones. These divisions are illustrated in an accompanying table, which gives detailed sections of the ore-bearing beds as found in the mines and shows the exact positions of the various ore zones within the formation. Key beds are described and the practical applications of stratigraphy in mapping, prospecting and mining are discussed. Introduction The Mascot-Jefferson City zinc district is in Knox and Jefferson Counties, in the Great Valley of East Tennessee. It extends from Mascot, I3 miles northeast of Knoxville, to Jefferson City, about 30 miles northeast of that city. The American Zinc Company of Tennessee is producing from five mines in the district, in which it has operated for more than 30 years. The only other important producer is the Universal Exploration Co. The approximate daily production of the district in 1943 was 5000 tons of sulphide ore, grading from 2.5 to 6 per cent zinc. Small amounts of oxidized ore are mined intermittently. The Knox dolomite has been described by various geologists,'-' but no detailed descriptions of the rock sections revealed by mining have been published. Rock units are not conspicuously different and careful study is required to distinguish them. Nevertheless, familiarity with the stratigraphy of the mineralized zones is essential to successful exploration and extraction of the ores; therefore the purpose of this paper is to give detailed stratigraphic sections as measured in the mines, to discuss their important features and to show their relationship to the stratigraphy of the district. Generalized Section Table I gives the most characteristic general features of the major stratigraphic units. The formation names given in parenthesis are locally and widely used terms, the correlations of which are not necessarily established. For this reason they are put in quotation marks and are replaced by more restricted terms. The names "Mascot" and "Kingsport" were adopted from local towns. They were chosen jointly by Josiah Bridge, of the Federal Geological Survey, and the senior author for use in their separate unpublished manuscripts describing the Knox dolomite in East Tennessee. Descriptions of the type sections may soon be published. The name "Longview" was first applied by Butts6 in Alabama.

Jan 1, 1949

By H. N. Mills

The glass industry is a major user of many industrial minerals in the manufacture of its product. It is the intent of this chapter to: (1) acquaint the reader with the glass industry by including a few production statistics, and (2) cover the various aspects of the major raw materials used to make glass. The matter of glass compositions, properties, and batches is considered beyond the scope of this chapter which deals only with raw materials. For more details on the particular minerals and rocks used in glassmaking, the reader is referred to chapters in the commodity section of this book. Glass Industry Statistics Glass manufacture in the United States can be divided into three major product classifications as follows: 1) Glass containers 2) Pressed and blown glass 3) Flat glass Glass containers include bottles and jars for the packaging of food and beverages, as well as drugs, chemicals, and cosmetics. Pressed and blown glass includes table, kitchen, art and novelty ware, lighting and electronic glassware, and fiber glass. Flat glass covers sheet or window glass, plate, laminated, and safety glass. The US Department of Commerce statistics, as recorded in the 1977 Census of Manufacturers, compares the dollar value of glass shipments for each product category. These statistics are shown in Table 1 (Anon., 1980) and are self-explanatory. A comparison of the tonnage output in each product classification is difficult, as production data is reported in "gross" for glass containers, "pounds" for fiber glass, "pieces" for glassware, [ ] and "square feet" for flat glass. In the case of glass containers, an average "pounds per gross" factor can be applied to the total production figures reported in thousands of gross in Bureau of Census industrial reports. Table 2 presents the calculated annual production tonnage for glass containers for the years 1974-1979. Except for 1979, there was a yearly increase in production. The tonnage figures of Table 2 are further influenced by decreasing weight per gross which has occurred in the glass container industry since 1975. This reflects the gradual shift to lighter weight containers for beverages. Other segments of the glass industry have experienced growth, but the figures in tons are not published information. Fiber glass growth has been influenced by the heavy demand for insulation as part of energy conservation efforts on a national basis. The production of flat glass by the float process has continued to grow with several new plants entering production. All portions of the glass industry experienced the effects of the general economic decline of 1979-1980, but the outlook for the future is bright. Batch Materials For Glass Use Materials and Function Soda-lime-silica glass represents the largest proportion of glass manufactured for commercial use. It is produced by the fluxing and

Jan 1, 1983

By Edward H. Robie

SUBJECT to formal Board approval in September, AIME dues will continue indefinitely at the present scale of $20 for Members and Associate Members; and $12 for Junior Members for the first six years of such membership, thereafter $17. That is the wish of the Board of Directors and the will of the membership, as expressed in the recent referendum. Though the official returns, as reported by the tellers, are not available as this is written, the data are sufficiently complete to give the results to the nearest percent. The total vote was approximately 93 pct for continuance of the present scale. Metals Branch members voted about 94 pet for continuance; Mining Branch members slightly less than that; and Petroleum Branch members about 91 pct. As in the referendum of 1949, there was no particular difference of opinion on the question of dues as between the three Branches. The percentage of ballots returned was about 61 pct, only slightly more than in the 1949 referendum. But the affirmative vote was much greater, 93 pct against 78 pet in the earlier referendum. Looked at another way, a majority of those to whom ballots were sent, 56 pct, voted to continue the present scale of dues, whereas only 46 1/2 pct of those canvassed voted to raise the dues in the previous referendum. But approximately 600 , members expressed their opinion that the dues should go back to $15 for Members and Associate Members and to $10 and $15 for Junior Members. This is a substantial group of members who either do not think they are getting their money's worth from AIME membership, or believe that a more businesslike conduct of Institute affairs should provide current services at less cost, or believe that more service is being provided for their dues than they need. As to the first point, it is probable that some members are not getting their money's worth. They perhaps have only a fringe interest in. AIME activities, or they do not or cannot participate in such activities at the Local Section, divisional, or national level, so that all they get out of the Institute is the monthly journal, which they do not have time to read. If they did read it intelligently, and acted upon the professional information thus gained, it is difficult to understand how one or more ideas cannot be gained that would be worth $20 to them professionally. But the 600 members who want lower dues offer a challenge to the Directors and to the staff to do a better job; to make Institute membership so rewarding that every. member will be thoroughly satisfied. Twenty 1935 to 1939 dollars are worth only $11.60 now, according to the latest government data, but that makes it all the more necessary for us all to appraise the value of what we buy. To the 93 pct of Institute members who expressed a vote of confidence, so to speak, the staff, and we feel sure the Directors as well, are most appreciative and thankful.

Jan 1, 1952