Search Documents

By R. L. Wilcox, M. L. Fuller

Owing to the nature of the die-casting process, fresllly cast alloys are undoubtedly not at equilibrium from the standpoint of alloy phase relationships. After casting, therefore, they tend to undergo phase changes, with the ultimate effeet of reaching a state of equilibrium at the aging temperature, beyond which no fnrther change takes place. This phase alteration undoubtedly is one of the primary causes of the changes in dimensions and physical properties that zinc-alloy die castings undergo during aging. It is planned to report on this problem in a series of papers of which this is the first. The writers have made a study of commercial zinc die-casting alloys over a period of several years, utilizing the X-ray diffraction technic of determining the phase composition changes in the alloys. Up to the present, two principal phase changes have been observed which are capable of causing dimensional changes: (I) the segregation of secondary constituents from the zinc-base solid solution and (2) the beta aluminum-zinc decomposition. The latter is the subject of the present paper and studies on the former will be reported upon at a future time. Scope of Study In the present investigation a special technic for the study of the beta phase in zinc-alloy die castings has been developed, making possible the determination of the period of existence of the beta phase after casting. The pure beta constituent and its decomposition have been studied in detail. The effect of magnesium and copper on the velocity of the decomposition is reported. The heat of decomposition, the eutectoid temperature arid the accompanying density change have been measured. The density change lias been calculated from data on crystal structure and the result thus obtained has been compared with the actual change.

Jan 1, 1935

By C. M. Marquardt

Tramp iron and steel moving on a conveyor belt cause small currents to be generated in a coil situated in a strong magnetic field, which are converted to an alternating current and are amplified. The output voltage from the amplifier fires a thyratron with a relay in its anode circuit, which actuates a howler and simultaneously drops a spot of marker material on the belt. THE problem of tramp iron removal from moving ore belts is a long standing one. When heavy ore streams are carried on a belt, magnetic pulleys and strong surface magnets fail to remove tramp buried in the ore stream. Tramp iron buried in the ore stream cannot be pulled from the bed by surface magnets and is carried past the magnetic pulley by the falling ore stream. With the increased use of detachable bits the problem of the detection and removal of tramp has become more necessary and difficult. Several types of tramp detectors have been developed. It would serve no practical purpose here to review exhaustively the literature on the subject. Methods of tramp detection used are: (1) The magnetic method, wherein the small current generated by the magnetized tramp passing a Coil is used. (2) The unbalanced oscillator method wherein the tank circuit of a stable radio- or audio-frequency oscillator is unbalanced causing a change of frequency or a change in plate current due to changes in eddy currents, hysteresis, or dielectric because of the presence of tramp. (3) The bridge methods wherein the impedance of one leg of an alternating current inductive bridge is changed due to the presence of conducting tramp. Each of these methods of tramp detection has its field of usefulness. The second and third methods are excellent for oxide iron ores, coal, sand and gravel, grain, etc. However, these latter methods are not suitable for use on ores that contain rich conducting sulphides, since a large piece of pyrite or galena will cause the same detector response as a piece of tramp iron. At the Caselton, Nevada, plant of the Combined Metals Reduction Co., sulphide ores are treated; therefore, it was necessary that a tramp detector operating on only the magnetic properties of the tramp iron be used. Tramp iron detectors of this type operate on the principle that if a piece of tramp iron moves near a coil in a high intensity, steady magnetic field, the presence of the moving tramp iron causes the magnetic flux lines through the coil to change. This induces a mall current in the Coil. In series with the Coil is generally placed a relay sensitive to currents of 1 to 3 microamp. When the tramp iron passes near the coil the flux linkages change, causing this very sensitive relay to actuate. Since the contacts of such a relay are very small it must actuate a second relay capable of breaking a larger current

Jan 1, 1951

By George C. Howard, P. P. Scott

During the drilling of wells, fractures which are created or widened by drilling fluid pressure are suspected of being a frequent cause of lost circulation. A study of the variables which are believed by the authors to he related to fracturing led to the premise that the presence of an effective lost circulation material in a drilling mud stream would serve to plug small fractures at the moment they are encountered or created and thereby a a possible cause of lost Circula. tion by preventing fluid pressure from widening and extending the fractures. A large number of lost circulation materials were classified and tested in simulated fractures and in shallow wells. Granular type materials with a gradation of particle sizes were found to be the most effective for plugging. Within the limits of pumpahility, the concentration in mud of each lost circulation material tested was found to be a controlling factor in determining the maximum size fracture which could be sealed. A new type centrifugal sorter was given preliminary tests and found to be capable of concentrating cuttings for rejection and reclaiming lost circulation materials. INTRODUCTION The control and prevention of lost circulation of drilling fluids is a problem frequently encountered during the drilling of oil and gas wells. Lost circulation or lost returns may be defined as the loss to formation voids of the drilling fluids or cement slurries used in the process of rotary drilling and well completion. The loss may vary from n gradual lowering of mud level in the pits to a complete loss of returns. Not to be confused with lost circulation is the continuous reduction in mud volume caused by the loss of the fluid phase of muds as filtrate and the solid phase as filter cake during the continuous filt~ation process which occurs on permeable formation surfaces. The loss of drilling fluids and their costly constituents is only one of the detrimental effects experienced when circulation is lost. The loss of drilling time, plugging of potentially productive formations, stuck drill pipe, blow-outs, excessive inflow of water, and excessive caving of formatioils are other effects which contribute to make the control and prevention

Jan 1, 1951

By Lewis W. MacNaughton, F. L. Burchard

The North Texas district, as herein defined, includes the counties of Archer, Baylor, Clay, Coolie, Foard, Hardeman, Knox, Montague, Wichita, and Wilbarger. This area covers generally the crest and south flank of a system of buried mountains known as the Red River uplift. The oil and gas accumulations along this feature are in traps, which, although localized by structures incident to the regional uplift, are usually modified by stratigraphic changes in the sediments. Excepting the fields in southeastern Baylor, southern Archer, and southwestern Clay Counties, all the fields within the district are on this Red River uplift. These exceptions, which have the same type of oil and gas accumulation as the other fields, are on the extreme north end of the Bend arch, which is a broad anticline plunging northward from the Llano uplift in central Texas to Archer County. The larger part of past oil and gas production has come from Pennsylvanian strata, with less important amounts from the Permian, and minor but increasingly important quantities from the Ordovician. DevELopments during 1941 Nearly 1600 wells were drilled in the district during 1941 as compared with more than 1700 in 1940. However, the ratio of successful drilling operations was higher and some 1200 oil wells were completed. Production held about even with the previous year, as did the number of producing oil wells. Known oil reserves increased slightly throughout exploration, which generally was carried on at greater depths than in former years. The average depth of discovery wells was 300 ft. deeper than in 1940. Although discoveries were evenly divided numerically between horizons above the base of the Strawn series and those below the Strawn, the deeper horizons, including the Bend series of the Pennsylvanian, the Mississippian limestone, and the Simpson and Ellenburger of the Ordovician, furnished most of the increase in oil reserves. The largest single addition to the reserves was in the Ellenburger formation in the K.M.A. field. During the year 112 wells were completed in this horizon, bringing the total developed acreage to some 4600 acres. The Straan series in K.M.A. also received considerable development in 1941, with 114 completions. K.M.A. Pressure Maintenance Satisfactory progress was made by the K.M.A. Pressure Maintenance Association in 1941. At the end of the year, 99 wells were being used for input and total monthly volume of gas returned to the reservoir reached a high of 340,548 M cu. ft. in December from a low of 208,853 M cu. ft. in February. Total volume of gas returned during 1941 was 3,306,052 M cu. ft. To the end of the year, 150 cu. ft. of gas had been returned for every barrel of oil produced from the reservoir while the input ratio for December was 397 cu. ft. Per

Jan 1, 1942

By E. O. Kirkendall

The investigation reported herein was undertaken to obtain data to supplement those presented in an earlier paper,l particularly for longer times at a higher temperature. This information may further develop our knowledge of the mechanism of diffusion in substitutional solid solutions. Diffusion of solute atoms interstitially dissolved is not difficult to visualize: it can take place without much disturbance of the solvent atoms. The mechanism of diffusion of solute atoms substitutionally dissolved is not so easily understood. Many theories have been advanced. Rosen-hain,2,3 Frenkel,4 Smekal,5 Langmuir,3,6 Steigman, Shockley and Nix,' and Johnson8 all proposed theories to explain diffusion. Langmuir's proposed mechanism consisted of a simple cyclic interchange of atoms involving an interchange in lattice positions of four or more atoms. This mechanism, accepted by the author at the time of his previous publication,1 and apparently quite generally accepted, required a net exchange in positions of both solute and solvent atoms in equal numbers. In other words, the rate of diffusion of the solvent and solute atoms would be the same. That this cyclic interchange in lattice positions of solute and solvent atoms in equal numbers is the only true mechanism of diffusion is denied by the evidence presented in this paper. Experimental Procedure This modification of similar procedure1 will be outlined briefly. The method consisted of the following steps: I. A pure Muntz metal (60.6 per cent Cu, 0.1 per cent total impurities) that was almost all beta brass at 780°C. was chosen. 2. The brass was turned between centers in a lathe to a diameter of 0.5965 inches. 3. After the brass was cleaned, it was electroplated with pure copper to a diameter of about one inch. 4. The sample was heated slowly to 400°C. under reduced pressure and held at that temperature for 4 hr. to remove occluded gases. It was then cooled to room temperature. 5. The sample was heated to 780°C. ± 3°C. and held at that temperature for different lengths of time; then quenched. Samples were cut off each time after quenching. Metallographic samples 1/4 in. thick were removed at I hr., 6 hr., 24 hr., 96 hr. and 701 hr. After 96 and 701 hr. samples of about I in. were removed for X-ray analysis. 6. The metallographic samples were polished on the cross section and photomicrographs were taken. 7. The I-in. samples were polished and etched on both ends. With the aid of a microscope each was carefully mounted in a four-jaw chuck in a lathe, so that they could be accurately bored for an arbor. 8. Turnings were taken for each X-ray sample. After each set of turnings, the sample was heated in an oil bath for about 1/2 hr. at 300°C. It was then etched in 25

Jan 1, 1942

By J. P. Newell, R. W Storey

This paper describes the development of a continuous float-and-sink process to produce coal low enough in ash content to be suitable for production of electrodes. The cleaned coal had a combined iron and silicon content of 0.239 pct. The efficiency of recovery was 84 pct. AUGER mining is a form of continuous mining in that it completely replaces with a one-cycle operation the older conventional cut, drill, shoot, and load method of mining. Relatively new, having been utilized only within the last few years, it is even more continuous in its production of coal than some other forms of continuous mining being practiced in this country today. There are at present coal recovery augers in operation working along strip-mined highwalls from the outside. This paper will deal with underground mining, specifically with an experiment which was carried out with a machine developed for this purpose. The location of this experiment was in Pike County in eastern Kentucky in the upper split of the No. 3 Elkhorn seam. Coal height was 32 in. and roof conditions were very bad, with 10 in. of soft draw slate coming down with every cut in conventional mining. The coal is high-grade bituminous, excellent for metallurgical coking. Underground auger mining fills a need for a method of recovering coal in thin seams, under bad roof conditions or in split seams. In many cases it might save money by eliminating the handling of excessive quantities of rock. In fact, if the coal can be recovered, as in the case of this experiment, without mixing with any impurities outside the seam, it may be possible to load or ship a satisfactory product with little or no preparation or cleaning expense. The need for some economical method for recovering coal from thin seams is becoming more pressing as the more profitably mined seams are exhausted. Basic Principles of Auger Mining The principles of the auger, or screw conveyor, have long been used in drilling small diameter holes for blasting and other purposes. These same fundamentals apply to large diameter drilling. However, considerably more attention was given to designing a cutting head that would not pulverize the coal and consequently would require a minimum of power to drive it. The head, as designed for this job, consists of a cylinder 25 in. in diam with steel bits set in 3 positions spaced around the forward rim. A conventional coal drill bit, at the head of a bursting cone in the center of the cylinder, trails the forward rim slightly, see Fig. 1. The bursting cone and auger connections are anchored to the cutter barrel by 3 arms spaced at 120". This head design proved to be very satis-

Jan 1, 1953

By E. D. Hummer, J. A. Younkins. J. P. Proctor

Comparatively little has been published relating practical experience with the control of the solid content of washery water systems that must be "closed." A "closed" system is one that for some reason may not be cleaned by the emission Of any effluent Of high ''lid 'content to be rep1aced by 'lean water in Order to hold the solid content of the waste water within reasonable bounds for efficient washing. It is the Purpose of this Paper to describe practical experience with such a water system and to present data that it is hoped may be of some use to those who are faced with a similar problem. The washery clarification system described comprises three thickeners and three filters, and although it is admitted that each of the fields of water settling and thickening and filtration offers a wide scope for investigation, the authors are not attempting to present the answers to these problems but to set down the results of some experience along these lines, making no claims as to the ultimate solution of the problems in hand. The subject of water clarification has vast ramifications; for example, the science of flocculation as applied to water settlillg and filtering opens up fields of wide possibilities of which as yet little is known. A comparatively recent entry into the field of water treatment, which may offer possibilities of practical application, is the use of "wetting" agents such as "Aerosol." General Arrangement of Water System So that the reader may obtain a comprehensive picture of the factors concerned in the control of a closed water system, it is necessary to give a brief description of the washing plant that is serviced by the water system to be described in the following pages. As we are not primarily concerned with the washing plant in detail, only a brief description of the flow of coal as it relates to the water system will be given here. For a more detailed account of this type of washer, the reader is referred to earlier papers,1,2 The washer, which handles o to 4-in, raw coal (750 tons per hour) is an American Rheolaveur plant of two complements; the coarse coal or sealed discharge plant and the fine coal or free discharge plant. The sealed discharge plant (Fig. I) consists of twin 48.in. primary launders, each having two washing boxes, supplemented by one 32-in. rewash launder, which also has two washing boxes. "Push" water for washing and conveying coal in these launders is supplied from a constant-head tank under pressure head of 10½ ft. at the point of introduction at the feed end of the launder. This tank also supplies water for upward or vertical currents used in the Rheolaveur or washing boxes. Each box discharges into a sealed boot elevator (Fig. I).

Jan 1, 1942

By A. T. Beckwith

The Lehigh Navigation Coal Company Inc. operates steep-pitch, relatively deep mines in the Panther Creek Valley, at the eastern end of the southern anthracite coal field. Commercially minable coal beds are the Mammoth,† Primrose, Orchard, and Buck Mountain;‡ their respective thicknesses average 50, 15, 10 and 12 ft. Sand slates immediately overlie and underlie these beds, though in some locations sandstone or conglomerate beds occur. Underground operations extend to a depth of 1200 ft. below the surface, and comprise a bulk of virgin work on the lower levels, and a small amount of remining on the upper levels. With increase in depth, ventilation has become a more important factor. Development In early days slopes or drifts were driven in the outcropping coal on the hillsides. Subsequent development was by water-level tunnels, with portals above high water in Panther Creek. These tunnels have been maintained because they intercept and drain much water that enters the mined-out portion of the bed and otherwise would follow down to the deep workings+ Below these tunnels, the coal was customarily developed by slopes. Muleways, which are zigzag chutes easy to travel, were also driven to connect lower openings with the water levels. When it became necessary to go still deeper, the slopes were abandoned, and vertical multicompartment shafts were sunk from the surface. Levels have been at vertical intervals of from 175 to 250 ft. Recent practice has been toward the latter spacing, splitting the total lift, however, by starting to mine from chutes extending halfway up to the level above. Chutes customarily are spaced at 50, 60 or 70-ft. centers along the gangways. At some mines, additional shafts have been sunk from the surface to the level containing the main pumping station, and these carry the discharge lines from the pumps. As the mines are ventilated by the exhausting system, both the hoisting and so-called water shafts serve as intakes. The main fan is always on the surface, and is connected with the return airways from the various levels by an air hole or a vertical shaft. For economy, when the present deepest levels were developed, and return-air shafts or air holes were not extended to the new level, but connections were made from the new level to that above by two or more holes. It is doubtful that this method will be continued, as complications in the system, increased resistance to flow, and other difficulties undoubtedly will counterbalance any economies this provision may afford. During the early years of mining, when operations were at no great depth, all development headings were driven in the coal bed. As mining progressed downward, increased ground pressures slowed develop

Jan 1, 1942

By C. Williams, D. V. Carter

During 1943 five oil fields and two gas-condensate fields were discovered in the East and East Central Texas district. The New Hope field, discovered by Tide Water-Seaboard in Franklin County, is the most important oil discovery since the Hawkins field in 1940. At the close of the year two oil sands were producing and two additional oil sands were being tested. The gas-condensate fields of Appleby in Nacog-doches County and the Stewards Mill field in Freestone County had only one producing well each. The Carthage field was extended 3 miles north and 4 miles west. Another well that was testing at the year end indicated a probable eastward extension of several miles. The Quitman field, in Wood County, was the most active from the standpoint of drilling operations. Approximately 48 wells were complcted during the year. The second and third most active fields were Hawkins field, Wood County, and Kildare field, Cass County, respectively. Wartime restrictions of material, together with manpower shortage and Federal spacing regulations, reduced the number of oil and gas-well completions from 265 in I942 to 171 in 1943. This represents a drop of 35 percent, or approximately 1/3, enough to replace the 531 producing wells abandoned in the district during the year. No changes were made in the price of crude oil in the district in 1943. The district produced 177,652,940 bbl. of condensate and oil during 1943. This represents an increase of approximately 11 per cent compared with the previous year. The East Texas field, which is the largest and most important field in the district, had an annual production of 128,568,647 bbl. of oil, which is approximately 6.5 per cent more than the previous year, and represents 72 per cent of the district's production of condensate and oil for the year. The district had an estimated basic daily allowable of approximately 509,000 bbl. of oil on Dec. 31, 1943. The entire district produced approximately 30 pcr cent of the state's production for the year 1943. The Hawkins field, Wood County, was operated 271 days during the year and with an average daily production of approximately 52,488 bbl. for the year. This field, which is the second largest in the district, produced 14,224,164 bbl, of oil during the year. Changes in annual production in certain fields in the district can be attributed to their ability to produce at higher rates, the demand, and transportation facilities in the war effort. The East Texas field showed an over-all decrease in reservoir pressure of 8.30 lb. during the year. Indications were that through the first quarter of 1944 the return of salt water to the reservoir was having a beneficial effect. It is hoped that, as more and more water is returned to the reser-

Jan 1, 1944

By William H. Spice

For the year 1943, exploratory drilling in South Central Texas continued on the sharp decline that started during 1942. Of the 3 counties comprising this district, as now revised to include the same area as is covered by District No. I, Oil and Gas Division, Railroad Commission of Texas, I5 counties are producing oil or gas. Only 29 exploratory wells were drilled during 1943, as compared with 51 exploratory wells in 1942, or a decrease of over 40 per cent. One new oil field and one new gas field were discovered during the year and a new horizon was discovered in an existing oil field. This cornpares with two new oil fields and an extension to an existing gas field in 1942. The one new oil field, South Washburn, in southeastern La Salle County, was discovered by Quintana Petroleum Corporation's No. I-D South Texas indicate in April 1943, flowing 4 bbl. per day, 48" A.P.I. gravity oil with an estimated 4 million cubic feet of gas from Wilcox sand at 6030 ft. This well i's the result of an extensive seismograph survey of the area. It is about 434 miles southwest of the same company's Green Branch field and by the end of the year one dry hole had been drilled to the southwest of this discovery. The one new gas field, which was not named, was located in eastern McMullen County by Edwin M. Jones' No. 102 Ezzell, in November 1943, for an estimated 8 million cubic feet of gas from shallow Jackson sand at 1222 ft. NO addi- tional wells have been drilled in this area, which may also be considered as an extension to the South Calliham field. The one new producing horizon was discovered in the South Campana field in southeastern McMullen County, by Argo Oil Corporation's No. 2-G Edrington, in January 1943, flowing 55 bbl. per day, 21' A.P.I. gravity oil with 40 per cent water from Government wells sand at 2609 feet. None of these discoveries were of major importance and subsequent development in these new areas has proved to be disappointing. Produc'tion for the district during 1943 totaled approximately 6,985,000 bbl. from about 3430 producing wells. This is an increase in production of about 5 per cent over 1942, but a decrease in producing wells of about 10 per cent under the number of wells producing in 1942 for the same district. Average production per well was 5.4 bbl. during 1943 as against 4.8 bbl. during 1942. Approximately 5,320,000 hhl. of this total production, or 76 per cent, was produced by the four Edwards lime fields, Luling, Branyon, Salt Flat, and Darst Creek, which are from 22 to 14 years old. The remaining production came from the 43 other active oil fields in the district. Drilling in the proven fields maintained approximately the same level as for 1942, with a total of 36 wells drilled. Of these operations, 21 were oil wells, one was a gas well and 14 were dry holes. This is a slightly better proportion of producers than for 1942. Washburn field had the greatest number of new producing wells drilled during the year, with a total of 10.

Jan 1, 1944

By Alec M. Crowell, Harry P. McClintock

Production of oil and gas condensate from the 45 oil and gas fields of South Arkansas increased for the eighth consecutive year, the production for 1943 being 27,605,647 bbl. Six new pools were discovered during 1943, bringing the state's crude oil and condensate reserve to 475 million barrels, a net increase of 70 million barrels for the year. The gross increase in proven reserve was 98 million barrels, from which, of course, is subtracted production of approximately 28 million barrels to reach the net figure of 70 million barrels. There were 35 more wildcats in 1943 than in 1942, and 29 more wells were drilled in fields of the state. Sixteen companies operated exploratory crews during the year for a total of 677 crew weeks, divided as follows: 563 weeks seismograph, 111 weeks gravity and 3 weeks core drill. There was a decided increase in gravity work and a decrease in seismic work. The year started with 15 seismic crews and ended with 5 seismograph and z gravimeter crews. Geologically, it is interesting that the number of wells bottomed in Gulf, Comanche, and Jurassic strata were near equal for the year 1943. During 1942 Jurassic was much higher than the other two. However, Jurassic still led in wildcats for the year 1943. Abandoment of wells in the stripper areas of the state reached about the same figure for the year 1943 as for the year 1942; that is, 145 wells were permanently abandoned. However, 243 wells were drilled in 1943, as against 184 for the previous year. The completions for the year were divided into 103 dry holes, 137 oil and condensate wells and 3 dry gas wells. Among new developments perhaps the most significant was the pressure-main-tenance project for the Midway field of Lafayette County, which is utilizing fresh water as the maintenance medium. This is the first fresh-water pressure-maintenance operation during primary production of an oil field in the United States. The operator of the project, Barnsdall Oil Co., estimates that the ultimate recovery of oil from this field will be increased from 32.5 to 65 million barrels. The Midway pool is of the dissolved-gas type, but a similar project is getting underway for the Magnolia field, Columbia County, a pool of the gas-cap and water-drive type. Dual completion of wells, on concurrent production from two productive zones through a single well bore, became common practice in South Arkansas during the year. As the year ended, some 50 wells had been dually completed and it was estimated that the first 37 of these wells represented a saving of more than 2 1/4 million dollars and a saving in steel of 7000 tons. The majority of the wells dually completed were those reaching depths in the neighborhood of 9000 ft. below the surface and initially productive there. Selective completion at lesser depths in the same well bore proved mechanically feasible and economically sound. The year was marked by the successful completion and placing into operation of three large natural-gas desulphurization

Jan 1, 1944

By W. A. Bruce

This paper presents the essentials of a mathematical method of studying the pressure behavior of an oil reservoir as the fluids are withdrawn. Methods are shown Whereby the behavior of a reservoir can be used to predict the future relationship between withdrawals and pressure. The oil reservoir is considered as a small part of a large porous continuum, which contains for the most part water. The expansion of this water resulting from a decrease of pressure in the oil zone causes a movement of water that is an important factor in the relationship between fluid withdrawals and reservoir pressure. Examples are given to illustrate the methods of pressure prediction for a circular reservoir containing undersaturated crude, the pressure distribution over a field that has a uniform production rate, the effect of a fault line near a field, the mutual interference of near-by fields, and the perturbing influence of a gas cap. Applications of the analysis to well-spacing problems are shown. Introduction The pressure-prediction methods to be described here are based upon the conception of an oil pool as a small part of a large porous continuum, containing for the most part water. The formation containing this water may be thought of as extending over an area of many square miles and having one or more small bodies of oil or gas trapped in high spots or reservoirs. It will be treated as having the genera1 aspect of a thin, flat sheet with an over-all tilt to the horizontal and with numerous small high spots, tight zones, and irregularities This porous continuum will be treated as being much more extensive than the oil or gas zones, but will be recognized as terminating at such large boundaries as a general fault, outcrop, unconformity, or pinch-out. Throughout the greater part of this limited porous continuum it is likely that there is a hydraulic connection. If this is true, the removal of fluid in one place will cause a disturbance that eventually will travel to all parts of the continuum. This picture has led to the recognition of water as the major fluid in the porous continuum and in many cases the expansive nature of this water as the main driving force producing the oil. The next step is the solution of the general problem of compressible liquid behavior in porous media. The works of Hurst I and Muskat2 introduced the idea of using heat-flow mathematics to consider the problem of compressible liquid flow in a porous medium. Before their reports, it had been thought sufficient to use the incompressible fluid-flow work of S1ichter.3 Law Muskat4 pointed out in detail how far the incompressible-fluirl assumption, deviated from fact even for water, of which the compressibility is about 3 X 10-6 volumes per unit volume per pound per square inch. He showed that this deviation increased with increases of distance. For example, the incompressible-fluid formula might show good agreement with the

Jan 1, 1943

By George Fancher, R. L. Whitting

A typical drilling mud from the Hastings oil field, Brazoria County, Texas, containing only 8 per cent (dry basis) of material of colloidal dimensions, which is largely illite, was concentrated to a density of 10.2 lb. per gal. and used in this study. The effects of water dilution, treatment with complex polyphos-phates, temperature and the time of heating upon the rheological properties of the mud were investigated. It was found that water plays an important part in chemical treatment and that sodium acid pyrophosphate and sodium tripolyphosphate were more efficient than other complex polyphosphates for chemical treatment. Muds treated with either of these chemicals manifested maximum reduction in viscosity and minimum filtration rates at low concentrations. Furthermore, .mud treated to minimum viscosity with either of these two chemicals was virtually unaffected by heat-treatment. Introduction The drilling of deep wells is dependent upon the use of drilling mud, and problems frequently arise concerning the effects on mud of temperature, prolonged heating and aging. The use of chemicals to control the rheological properties of mud is a well-established practice. Salts of weak organic acids such as sodium tannate or gallate were used at first until the complex phosphates of sodium were found to be more efficient. Consequently, it seemed important to investigate the reaction of a mud to chemical treatment with phosphates, temperature, heat-treatment and aging, particularly since previous work in the laboratory at the University of Texas had provided the particle-size distribution and mineral composition of Hastings mud. Properties or Mud Used in Experiments A large sample of the mud from a drilling well in the Hastings field, Brazoria County, Texas, was obtained directly from the circulatory system. Some of the general physical characteristics of the mud and other data are presented in Table I. Table i.—General Properties of Hustings Drilling Mud Alex- Cur-ander keet Well Well Depth when sample was taken, It.. 5720 5700 Weight. lb. per gal............... 9.5 0.8 Viscosity, sec. A.P.I.............. 47 60 Viscosity, Stormer, grams......... 80 Viscosity, centipoises............. 13 Filtration rate, c.c. per 30 min.a. . . 19.6 22.8 Salt content (chlorides), per cent... 0.13 0.12 pH............................. 8.9 8.9 The Alexander mud was used for the experimental work. Comparison with Curkeet mud indicates a considerably greater dilution but otherwise suggests similarity. The mineral composition and particle-size distribution of Curkeet mud (Table 2) are available (Fancher and Oliphant6). It is suggested that Alexander mud would have a similar composition.

Jan 1, 1943

By F. C. Oliphant, George H. Fancher

Two samples of drilling mud from the Hastings oil field, Texas, were tested, and the solids in each were separated into small fractions of a limited range in particle size. The mineral composition of each fraction by X-ray analysis is reported, and the results are interpreted in relation to other measured quantities, such as the physical properties of the original samples and the density of the various fractions. It was found that only 7 to 8 per cent by weight of the solids was of colloidal dimensions and that neither of the samples contained montmorillonite but did contain illite. Considerable calcite was also found. These data should be useful to the geologist interested in the origin and history of sedimentary strata as well as to the petroleum engineer. Introduction The questions, What is good drilling mud? What constitutes bad drilling mud? are pertinent, because the proper use and control of drilling fluids has been a factor of great importance in the successful drilling and completion of oil wells since the days of Captain Lucas. Adequate control of the characteristics of drilling fluids has assumed greater significance comparatively recently because of the problems introduced by caving formations in deep wells, costly blowouts and impressive mud bills. Much is known about the solution of some of the problems but, despite extensive research directed toward a better understanding of the physical and chemical properties of clay suspensions, it is difficult to define precisely a drilling mud, and much more difficult to say what constitutes a good mud. It is generally believed that the smaller particles of a drilling mud greatly affect its physical properties. In fact, it is customary to blame the colloids in a mud for nearly everything that goes amiss, because colloidal properties have effects out of all usual proportion on viscosity, filtration rate and reaction to electrolytes. It is germane to know whether drilling muds possess colloids and if so, the quantity and kind. Source oF Samples Two drilling muds from the Hastings oil field, Brazoria County, Texas, were selected because it is generally agreed that in this oil field good natural muds made solely from formations penetrated by the drill can be used until the well is nearly ready for completion. Customary drilling procedure in this field is to spud in with water, set a protective string of pipe, drill to 2500 ft. and set the surface casing. Drilling is continued to 5500 ft. with no treatment of the drilling fluid other than addition of water to

Jan 1, 1943

By W. C. Krumbein

Geological problems are approached from a geometrical (space relations) viewpoint, a kinematical (time sequence) viewpoint, or a dynamical viewpoint. The first two require sound training in conventional geology and in field methods. The third approach requires a solid foundation of chemistry, physics, and mathematics. Modern training for geologists should include close integrltion of basic sciences with geological principles. Introduction Our knowledge of the earth has increased tremendously during the last half century. We know more about its surface configuration, the distribution of its natural resources, the proccssion of living forms that inhabited it in the past, the chemical composition of its oceans, the areal distribution of its surface rocks, the movements of its atmosphere, and so on. Not only do we know more facts about the earth, but we have a better understanding of the processes that take place on and within it, such as the nature of earthquakes, the thermodynamics of the atmosphere, the chemical equilibria involved in the formation of igneous rocks, the mechanics of stream flow, the dynamics of the earth's origin, and so on. Many sciences contributed to the sum total of this knowledge, including such established disciplines as geology, geography, physics, chemistry, astronomy, biology. Out of this accumulation of new knowledge grew also a group of new sciences, such as seismology, oceanography, meteorology, volcanology, hydrology. Collectively these latter are known as the geophysical and geochemical sciences, and to a large extent they began as branches of geology. Until the turn of the century, for example, the study of earthquakes (seismology) was a part of geology, although as early as 1846 Mallet, a physicist, had suggested that the subject could be investigated by elastic-wave theory. Comparatively little progress was made along these lines until the seismograph was developed near the turn of the century; since then, additional earthquake data have accurnul~ted rapidly, but more important, the interpretation of these data essentially has kept pace with their accumulation. In similar fashion, meteorology was generally considered a branch of geology as recently as one or two decades ago. Considerable progress had been made in such aspects as weather forecasting, but the science dates its recent rapid rise from the year 1911, when Bjerknes first applied the principles of dynamics to the analysis of air masses. The rapid development of such disciplines as oceanography, volcanology and hydrology was due in part to the application of principles of chemical equilibrium, of dynamics, and of thermodynamics to earth problems, by men who were essentially physicists or chemists by training. The last half century, therefore, and particularly the last two decades, saw the influx of numerous chemists and physicists into the realm of the earth sciences. In the meantime the main body of geology itself showed a marked growth, and

Jan 1, 1946

By T. I. Harkins, J. Brian Eby

This paper outlines the geophysical investigation of the area covering the D arrow salt dome, Louisiana. Surveys with the refraction seismograph and torsion balance failed to disclose the dome, but reflection dip shooting was successful and was confirmed by later drilling. Introduction The D arrow salt dome and oil field lies in western Ascension Parish, Louisiana, on the outside of a sharp bend and on the east bank of the Mississippi River. The dome occurs about 30 miles south of Baton Rouge and 80 miles northwest of New Orleans. Its geology, shape and structure have been ably described in detail by Carroll E. Cook' and, except for the general features, will not be repeated here. The purpose of this paper is to record some of the interesting and pertinent geophysical data contributing to the discovery of the dome and eventually the oil field. The salt dome is circular in outliie and comes to within about 4625 it. of the surface. At this depth the diameter of the salt plug is approximately 4800 it. The dome has only a thin cap rock of less than 75 ft. Some oil has been found and is being produced in Miocene sands above the cap rock, but most of the field's production comes from a narrow ring of wells around the east and south flanks of the dome. Producing horizons on the flank are found at 5670 to 5840 ft. in the Miocene and 6890 to 6985 ft., 7028 to 7060 ft. and 8260 to 8270 ft. in the Oligocene. The deepest well that has been drilled is the Humble Oil and Refining Company's Community B-5, on the south flank of the structure, which reached a depth of 10,013 feet. The size and shape of the field and the area of production are indicated on Fig. I. The lie showing the area of production encloses all wells now producing and all abandoned producers, both on the top and flank of the dome. This line of production is shown on all subsequent geophysical maps as a direct means of comparing the early geophysics to later drilling development. Darrow dome occurs on the low, flat flood plain of the Mississippi River; it is protected from flood overflow by high artificial levees. The rich loamy soil supports a high degree of cultivation, principally sugar cane. Drainage is secured by many small canals and the water table of the area is at or near the surface. These particular conditions of topography, drainage and top soil greatly influenced the early geophysical picture, and the influence was always unfavorable.

Jan 1, 1946

By B. Otto Pixler

Mud-analysis logging provides identification of the fluid content of formations drilled by the rotary method and permits the accurate correlation of oil and gas shows with the depth. Mud-analysis logging eliminates much coring and has an especially important application in drilling programs when coring is particularly hazardous or the electric log is difficult to interpret correctly. An appreciation of the factors that influence the results of the mud analysis, such as rate of penetration, mud properties, coring, and characteristics of reservoir rock as related to the "flushing effect," permits a better understanding of the mud-analysis log. Recent studies of the relationship of the two gas readings obtained by the gas-detector instrument have proved significant. The difference between the total combustible gas reading and the higher molecular weight gas reading indicates the presence of methane. With few exceptions, zones not showing an increase of methane probably can be condemned. Mud-analysis logging furnishes valuable information, which generally cannot be obtained by other methods. Introduction Logging by mud analysis of wells drilled with rotary tools is a direct method of locating oil-and-gas-bearing formations. The use of this method of logging has increased each year until now more than 20 field units are being used in 13 oil-producing states and in some foreign countries. Several papers1-9 have been published in the petroleum trade journals describing in detail the equipment and the application of mud-analysis logging. This paper will discuss briefly the method and review its application and some of the late developments. Method As the drilling of a well progresses, the drilling bit dislodges and disintegrates a cylindrical section of the formation. If oil or gas is contained in the pore spaces of the cylinder, some of the contents of these porous spaces will be entrained in the drilling fluid. In wall logging by mud analysis, the mud is continuously examined for oil and gas on its return to the surface, and the results are correlated back to the actual depth of the hole at the time the mud was clearing the eyes of the bit. The test for gas is made by diverting a portion of the circulating mud from the flow line to a separator or gas trap, where the mud is thoroughly mixed with air and a portion of the gas entrained in the mud is removed. A stream of air is drawn coun-tercurrent to the flow of mud in the gas trap, thus materially assisting the separation of the gas from the mud. The air-gas mixture is then drawn into a "hot-wire" gas-detector instrument where the percentage of the combustible gas is determined. The presence of oil in the formation drilled is detected by a physical examination of the drilling mud under ultraviolet light. A sample of the mud is treated to reduce the surface tension and gel strength, after which it is placed in a viewing box. This box is so constructed that all external light is excluded and so that the sample may be subjected selectively to either ultra-

Jan 1, 1946

By N. A. D. Parlee, N. M. El Tayeb

Fe-V alloys with small percentages of vanadium show no deviations from Sieverts' Law up to P~, = 1 atm in the 1600º to 1750ºC region. At somewhat under 8 pct V and up to at least 20pct V, at 1604" and 1661 °C, nitrogen absorption follows Sieverts' Law at low Pn2 values, but deviates from this law beyond critical values of pn2, due to formation of a nitrzde phase of approximately VN composition. The behavior below these solubility limits can be described at all temperatures by the equations: RAO and parlee1 suggested that the nitrogen absorption curve for liquid iron alloys takes the general form shown in Fig. 1 when an alloy nitride precipitate is formed. They showed that the precipitation of 6 titanium nitride from liquid Fe-Ti alloys follows this general scheme and dealt with the general theory involved. Recently, Evans and Pehlke2 reported their research on the precipitation of aluminum nitride from liquid Fe-A1 alloys. Fountain and Chipman's recent paper3 on the precipitation of boron nitride from solid solution contains a fine example of the analogous behavior which they have been studying in the solid state. Researches on the absorption of nitrogen by liquid Fe-V alloys have been described by various authors.1,4-7 Most of this work has been confined to fairly low vanadium concentrations and rather high temperatures because of difficulties variously described as, formation of surface scums, bridging, and so forth. This behavior and the rough thermo- dynamic calculations made by chipman,8 over eleven years ago, indicated that excessively high vanadium concentrations should not be required for vanadium nitride precipitation. It seemed desirable to look for and study this precipitation in order to fill out the thermodynamically interesting nitrogen absorption data on these alloys. EXPERIMENTAL METHOD The general method used was essentially the same as employed by Rao and parlee,1 in which a Sieverts type of apparatus was used and the precipitation of the nitride detected by the "break-point" in the Sieverts' Law line, and by the visual observation of the formation of the new phase on the surface of the melt. There were, however, a few differences in apparatus and technique as described below. The oil manometer used by Rao and parlee' to measure low partial pressures of nitrogen was not employed. The present authors sought to avoid as much as possible the exposure of the liquid alloy to low total pressures of gas during the 6 to 10 hr long runs because of the heavy iron evaporation-loss errors involved. This was achieved, partly by keeping evacuation times to a minimum with fast pumping but largely by the use of two burettes, one for argon and one for nitrogen, and using them to equilibrate the alloy with mixtures of argon and nitrogen rather than nitrogen alone. Each run involved a careful sequence of operations. After melting, de-

Jan 1, 1963

By W. A. Bruce

This paper presents the essentials of a mathematical method of studying the pressure behavior of an oil reservoir as the fluids are withdrawn. Methods are shown Whereby the behavior of a reservoir can be used to predict the future relationship between withdrawals and pressure. The oil reservoir is considered as a small part of a large porous continuum, which contains for the most part water. The expansion of this water resulting from a decrease of pressure in the oil zone causes a movement of water that is an important factor in the relationship between fluid withdrawals and reservoir pressure. Examples are given to illustrate the methods of pressure prediction for a circular reservoir containing undersaturated crude, the pressure distribution over a field that has a uniform production rate, the effect of a fault line near a field, the mutual interference of near-by fields, and the perturbing influence of a gas cap. Applications of the analysis to well-spacing problems are shown. Introduction The pressure-prediction methods to be described here are based upon the conception of an oil pool as a small part of a large porous continuum, containing for the most part water. The formation containing this water may be thought of as extending over an area of many square miles and having one or more small bodies of oil or gas trapped in high spots or reservoirs. It will be treated as having the genera1 aspect of a thin, flat sheet with an over-all tilt to the horizontal and with numerous small high spots, tight zones, and irregularities This porous continuum will be treated as being much more extensive than the oil or gas zones, but will be recognized as terminating at such large boundaries as a general fault, outcrop, unconformity, or pinch-out. Throughout the greater part of this limited porous continuum it is likely that there is a hydraulic connection. If this is true, the removal of fluid in one place will cause a disturbance that eventually will travel to all parts of the continuum. This picture has led to the recognition of water as the major fluid in the porous continuum and in many cases the expansive nature of this water as the main driving force producing the oil. The next step is the solution of the general problem of compressible liquid behavior in porous media. The works of Hurst I and Muskat2 introduced the idea of using heat-flow mathematics to consider the problem of compressible liquid flow in a porous medium. Before their reports, it had been thought sufficient to use the incompressible fluid-flow work of S1ichter.3 Law Muskat4 pointed out in detail how far the incompressible-fluirl assumption, deviated from fact even for water, of which the compressibility is about 3 X 10-6 volumes per unit volume per pound per square inch. He showed that this deviation increased with increases of distance. For example, the incompressible-fluid formula might show good agreement with the

Jan 1, 1943

By Howard I. Epstein, John R. Buzek

Thickeners are simply large tanks, usually circular in shape, which are designed to allow settling of solids and to operate with continuous overflow of clear water and underflow of thick pulp. The dimensions of the thickener are usually such that dewatering of very fine pulps may be accomplished while still overflowing clear water. Some thickeners such as the Center, Hardinge and Hydrotator types combine thickening with filtering2 while others such as the Dorr type are pure thickeners. l .2 , 3 A schematic diagram of the traction type Dorr thickener is shown in [Fig 1]. This type is appropriate for tanks over 15 m (50 ft) in diameter. This tank employs a rotating raking mechanism which moves the settled material toward the central discharge. For this and other thickeners, it is common to have a shallow conical tank bottom in order to conform to the geometry of the raking mechanism, and it is often desirable to elevate the tank for ease of access to the product. When the tank does not rest on the ground, the forces resisted by the cone are large, and thick plates must be employed. The fabrication of these tanks requires temporary supports in order to erect the cone. A flat-bottomed tank could also be used because the settled material would soon form a hardened conical surface. However, because of the presence of large bending forces, even larger plate thicknesses are required than for the conical bottom. Significant cost savings often can be realized by the use of a scalloped-bottomed tank such as the one partially shown in [Fig. 2]. The particular scalloped bottom discussed in this paper employs radial beams forming the outline of the cone-shaped bottom. These beams are supported directly by columns. Cone segments are hung between adjacent beams. The exact geometry of these segments depends upon the cone angle and radius, the number of radial beams, and their inclination. The geometry is chosen to satisfy certain clearance restraints and to utilize the material as efficiently as possible. The resulting thickness of these segments is significantly less than that of the equivalent plate for the tank with a conical bottom. This result, along with the simpler fabrication procedures required, accounts for the cost savings associated with this design. The raking mechanism employed may be the same as for the conventional conical bottom since the settled material soon forms a conical surface. Determination of the internal force mechanism for the scalloped bottom leads to designs that utilized material efficiently and thus maximize the cost savings. The complicated geometry of these bottoms along with the difficulty in analyzing the structure are factors which may have limited the use of scalloped-bottomed tanks to date. When such tanks have been built, the uncertainties associated with the internal forces have led to designs that are somewhat inefficient. In this paper, equations relating the geometric parameters are presented along with simplified closed-form solutions for the internal forces in the cone segments, from which the loads applied to the beams and the loads carried to the cylindrical tank shell can be deduced. An example is presented to show the magnitude of the savings which may be realized with this configuration.

Jan 1, 1979