Search Documents

By R. L. Wiegel

The generation of operating information for mineral beneficiation processes has become more sophisticated as a result of the use of improved laboratory analytical techniques, some of which provide multiple component assays, as well as the introduction and gradual industrial acceptance of process sensors for the measurement of flow, density, size, and chemical composition. In general, however, the mineral processing engineer's ability to tie together this wealth of information has not kept pace with these developments. In fact, in almost all existing plants, the metallurgical inflow-output balance, wed to indicate current process performance, is still being calculated from only a small portion of the information routinely available. There is substantial activity in the development of techniques for using all available process information to significantly improve the reliability of the metallurgical balance. While the use of these improved techniques does require access to computing facilities and a slight change in perspective on the part of the mineral processing engineer regarding the inviolability of process information, there are numerous practical benefits to be derived from their application. In addition to summarizing some of the concepts basic to these techniques, this paper describes the experience of the author in applying one of these advanced metallurgical balance techniques to a variety of pilot plant and commercial plant flowsheets during the past eight years.

Jan 1, 1983

By William Wraith

At the Washoe smelter, Anaconda, Mont., the blister-copper from the converters is transferred, by means of a crane, to a re-fining-furnace, in which it is brought to proper pitch by means of air and poles. From this furnace the refined copper, containing gold and silver, is poured into cast-iron molds placed on a platform-convejor, giving an anode 36.75 in. long, 35 in. wide, and 2 1/16 in. thick. By reason of a disagreement between the smelter and the refinery, in reference to the silver-content of the anodes, it becanle necessary to investigate the methods of sampling used. 11. SMelter Method of SampliNg. At the smelter the sampling is done by " shotting " into water a small portion of the molten stream of copper as it flows from the furnace, by " batting " the stream'with a wooden paddle. The first sample is taken 30 min. after the pouring i.: started, three other samples being taken at 1-hr. interrals, each sample Weighing from 4 to 6 oz. The samples are dried, esamined for particles of burnt wood, screened on a 10-mesh screen of NO. 8 wire to remove the fines, the oversize then screened on a 4-mesh screen of No. 20 wire to remore the coarse, the undersize of this screen being taken as the sample. The four portions thus obtained are thoroughly mixed and split in half by passing over a 16-slot splitting-device, slots being 0.5 in. wide. One-half of the sample is sent to the laboratory for analysis and one-half kept as a duplicate. 111. Refinery Method of Sampling. The method used at the refinery and also used in this in1-estiyation is the one developed by Dr. Edmarcl Keller, of

Jan 1, 1911

By L. A. Dale, D. A. Dahlstrom

Closed-water circuits are justified today from two standpoints: economical operation and prevention of stream pollution. In today's modern preparation plant, it has been found very desirable to have the plant circulating water maintained at a relatively low solids concentration of around 3%. In so doing, bene-ficiation equipment can operate at a much higher efficiency. However, makeup water requirements would become excessive if the fines were to be removed from the preparation plant by bleeding a 3% solids concentration to a tailings pond. With the ever increasing percentage of —200 mesh coal, clay and slimes in the raw coal, coupled with the creation of these fines within the preparation plant, the need for water conservation for economy reasons becomes even more important. Because of stream pollution laws, tailings ponds have become very costly to operate and maintain, resulting in the necessity of employing an in-plant method of water recovery. Accordingly, the primary system employed in water recovery in the coal preparation plant today consists of a solids concentration device to thicken refuse solids while at the same time producing a sufficiently clarified effluent that can go back to the preparation plant for water reuse. The thickened product is then normally passed to a dewatering device that will produce a handleable solid that can be disposed of

Jan 1, 1965

By Alan Morris

In a previous paper1 the results of cutting tests on free-cutting brass rod were reported. Investigation was made of the effects of variation in lead content, microstructure and cold drawing. The author's reply to the discussion of that paper includes a study of the directional cutting properties of drawn and annealed rod. The present paper records the results of tests made on series of samples in which the tin, iron and copper contents have been varied. The apparatus used and method of testing are described in detail in the previous paper. The machine is of the pendulum-operated milling type used and described by Airey and Oxford.2 Angular readings of the height to which the pendulum rises after falling from a fixed position, both when a cut is made and when the pendulum swings freely, give the basis for calculation of the energy consumed in making a cut. Careful weighing of the sample before and after cutting gives a measure of the amount of metal removed. The results are expressed in footpoiinds per cubic inch of metal removed, and have been called "unit cutting energy." In the course of the discussion of the author's earlier paper, W. B. Price reported large-scale tests involving some 50,000 lb. of material. These tests indicated that the addition of as much as 0.6 per cent of iron and 0.25 per cent of tin had apparently no adverse effect on the highspeed cutting characteristics of the rod. The rod also contained a small amount of nickel. The test results reported here tend to confirm his observations. Effect of Variation in Tin Content The castings for this series were made 2 by 1 by 9 in. and were processed as follows: 1. Castings were annealed at 500" C. for 7 hr. 2. Cold-rolled to 0.700 in.

Jan 1, 1933

By John Mathews

IT is twenty years since the writer made his first molybdenum steels and others were making them commercially five years earlier but the prevailing opinion seems to be that molybdenum steels are new; from time to time the daily press speaks of important discoveries in Europe and intimates that American steel makers have much to learn in regard to alloy steels. The earlier experiments were largely confined to the use of relatively high percentages of molybdenum in tool steels and permanent magnet steels. Recent developments deal with the types of alloy structural steels used for airplane, automobile, and other engineering requirements; in these, the molybdenum content is usually less than 1 per cent. The earlier types generally have been unsuccessful commercially, but the newer types of steels are becoming of increasing importance. The war showed our dependence on foreign sources for alloying metals; molybdenum alone is widely distributed in the United States and seemingly abundant. Many deposits are not now of commercial interest, owing to location and relatively small amount of ore available, but other deposits are being developed and a stable source of supply seems well assured. In tool and magnet steels, it was early found that 1 part of molybdenum was equivalent to from 2 to 2.5 parts of tungsten. The permanent magnet steels investigated by Madame Curie,1 in 1898, contained from 3.36 to 4.05 per cent. molybdenum; in 1902, Dr. E. L. French and the writer thoroughly tested steels containing from 2:0 to 4.0 per cent. These steels gave satisfactory tests for permanence, but were low in residual density and much more sensitive to hardening than the corresponding tungsten products. We discontinued work with them, therefore, and have no advice that such steels have been used commercially here or abroad.

Jan 2, 1921

The Library of the above-named Societies is open from 9 A.M. to 10 P.M. on a11 week-days, except holidays, from Sept. 1 to June 30, and from 9 A.M. to 6 P.M. during July and August. The Library contains about 55,000 volumes, including sets of technical periodicals and the publications of scientific and technical societies. Members of the Institute, with few exceptions, are forced to spend a portion of their time in localities isolated from sources of information. To these the Library can render valuable service through correspondence; letters requesting information will receive special attention. The Library is prepared to furnish references and copies of articles on mining and metallurgical subjects; to determine the existence of mining maps, and to furnish general information as to the geology and mineral resources of all countries. All communications should be made as definite as possible so that the information received may be what is desired and not include collateral matter which may not be of interest. The time spent in searching for such collateral matter will be saved, and the information will be sent more promptly and in more usable shape. The members of the Institute can be of service to the Library by for- warding copies of mining reports, maps privately issued, and similar material, which will be classified, indexed, and made available to other members. Suggestions for additions to the Library, either by purchase or personal solicitation as gifts, will be welcomed. It is hoped that members while in the city will use the Library freely, and assurance is given that most careful service will be rendered to them.

Jan 8, 1916

By E. R. Shorey

FLOTATION-Mill operator's have recognized that slimes are detri-mental to the flotation concentration of zinc ores. The, presence of primary slime in many of the Wisconsin ores is largely responsible for the failures experienced in treating these ores by flotation. These failures have discouraged the adoption-of the flotation process by opera-tors in the Wisconsin zinc district. The removal of slimes by decantation seemed to be the obvious way to meet the problem of treating slimy or' clayey ores by flotation. To facilitate the removal of slime, it was decided to mix the ore pulp with sodium silicate, which acts to deflocculate the pulp.1 Deflocculation causes slime suspension, making it possible to separate the slime from the sands by decantation.2 Since the literature contains little definite information on the use of sodium silicate to deflocculate ore pulps, a series of tests was conducted to obtain the necessary information. Tests to determine the settling rates of sand and slime in deflocculated pulps were conducted on a dolomite-marcasite-sphalerite ore ground to minus 80 mesh (175 microns) and mixed with water to form a pulp. The deflocculator3 was Mallinckrodt 40° to 42.5° Bé. liquid sodium silicate (Na20 + 3.25Si02). .By microscopic analysis the suspended slimes4 were found to be minus 15 microns (approximately 1000 mesh).

Jan 1, 1934

By R. S. Handy

THE properties of the Patiño Mines and Enterprises Consolidated, Inc., a New York corporation, are near Llallagua in the department of Chayanta in the west central part of Bolivia, South America, about 80 miles southeast of Oruro and 250 miles southeast of La Paz, the largest city in Bolivia and its virtual capital. The properties are accessible by railroad from three points on the west coast-from Mollendo, Peru, across Lake Titicaca, from Arica by way of La Paz, and from Antofagasta, Chile. The latter route, although the longest, is recommended by the companies as affording a more gradual introduction to the high altitudes; the mine being 13,000 ft. above sea level. The company operates its own railroad from its properties at Uncia to Machacamarca on the Chile & Bolivia R. R., a distance of 60 miles. This railroad is well equipped and well operated, and its location among the mountains surrounding Uncia represents excellent engineering skill. In fact all of the railroads, although they are of only a meter gage, are remarkable for the excellence of their construction, the arrangement of their dining and sleeping cars and the precision of their operation. There is only one drawback to rail- road and hotel accommodations and that is the absence of heating facilities, which does not seem to affect the natives but keeps a tenderfoot's teeth chattering continually. The company is a consolidation of the Patiño company, owning properties at Uncia, with the Compafiia Estanfera de Llallagua, a' Chilean corporation owning contiguous properties at Llallagua. Before the consolidation these companies were deadly enemies, and there still remain at the surface plant at Uncia the fortifications and underground defences provided during the warfare between the two factions. Also, in the Azul, or "Blue" tunnel at the junction line between the two properties is a strong steel barricade still bearing marks of the bullets fired during the various armed tilts between the workmen of the two companies. The headquarters for the mining operations and the milling plant have been moved since the consolidation from the original location at Uncia to the Llallagua side of the mountain, where the Chilean company's operations were carried on. The historic old town of Uncia, with its massive stone buildings of Spanish design, is a wreck, while the Llallagua side is being rapidly built up with modern structures.

Jan 1, 1929

By Effingham Humphrey

THE Lehigh Valley. Coal Co. finished the rebuilding of its Drifton No. 2 breaker at Drifton, Pa., in the summer of 1917. The new construction comprises an addition and the complete remodeling of the old breaker. It is of interest to note that the old structure was the first iron breaker erected in the anthracite region. THE OLD BREAKER This old breaker was built by the Cross Creek Coal Co., under the direction of the late Eckley B. Cole, in 1888-89, and was fully described by him in the Transactions.1 The columns were cast iron, 8,'10 and 12 in. square. The floors and partitions in pockets were cast-iron ribbed plates. The struts were cast iron of "H" section; the other members were of structural iron either rolled I-beams or built-up sections. The sizes of the rolled beams varied from 6 to 20 in. deep, while the built-up sections, made of plates and angles, varied from 6 to 63 in. in depth, so that there apparently was no rule to determine the type of section used. In the remodeling of the old structure, practically everything was taken clown excepting the columns and roof, and such beams as were necessary for temporary construction purposes, and, therefore, a close inspection of the old structural members could be made and the effect of the acid water oil them could be noted. The cast-iron members were but slightly attacked by the water, while the wrought-iron beams, in the wet places, were corroded almost to failure.

Jan 2, 1918

By P. W. George

THE rapid increase in cost of discovering new orebodies by churn drilling in the Tri-State district has led to some attempts to lessen the expense by using geophysical methods. Electrical prospecting was tried three or four years ago, but no successful results were recorded. In 1926, the Federal Mining and Smelting Co. engaged the North American Exploration Co., of Houston, Texas, to make some tests with the torsion, balance. At first, it was thought that the most favorable conditions for discovery of ore deposits with the torsion balance would be in locations where the ore was known to occur at rather shallow depths, FIG. 1.-CROSS-SECTION OF DUENWEG LEASE. therefore the first trial was made at Duenweg, east of Joplin, where some zinc ore had been developed at a depth of 130 ft. The gravity gradients at 61 stations on a tract of about seventeen acres indicated plainly one large zone of maximum gravity and a smaller narrow zone of minimum gravity. Fourteen churn-drill holes, half of which struck .ore, show that all the ore found was located outside the zones of maximum and minimum gravity. In the zone of maximum, gravity the limestone beds were closest to the surface, and the first chert beds encountered were at the greatest depth. The results (shown in Table 1) indicated that the gravity of the limestone was greater than the gravity of the fractured chert together with its orebodies, and probably also greater than the bouldery soil and clay on top of the limestone. A cross-section of the Duenweg lease is shown in Fig. 1.

Jan 1, 1928

By J. M. Mutmansky, Y. J. Wang, H. L. Hartman

Procedures for determining the operating point that results when a fan is connected to a mine and placed in operation have been a source of confusion for decades. A variety of techniques have been proposed, often to the detriment of the practicing ventilation engineer trying to apply the techniques to the many mine/fan matching problems encountered in the engineering of mine ventilation systems. This paper proposes some different assumptions and definitions that simplify the problems in determining the operating point. As a result, a set of procedures is provided for determining the operating point of a mine/fan system when the outlet areas of the mine and fan are known. To simplify the development of procedures for determining the operating point for a mine/fan combination, the authors suggest that the mine pressures be redefined and then used in such a manner that the conservation of energy is ensured. This provides the basis for the recommendation that the fan operating point be determined using the fan total pressure and the system total pressure characteristics. This procedure can be applied to fans in the blower, booster, and exhaust positions equally well, and to both single-fan and multiple-fan networks. Another advantage is that the method is applicable to fans with or without an evase.

Jan 1, 1986

By Waldemar Lindgren

CONTENTS. [ ] I.-CHARACTER OF THE DEPOSITS. 1. Principal Features. IN many schemes of classification and description the term contact-deposit has been somewhat loosely applied to all accumulations of useful minerals (other than those of unquestioned sedimentary origin) which are enclosed between two different rocks. As thus used, the term may include deposits of widely differing origin, and, unless qualified, is not in place in a genetic classification. The present paper deals with a special class of contact-deposits. In many geological provinces, granular igneous rocks, such as granite, diorite and syenite, have broken through and invaded sedimentary rocks. The molten magma may in part have reached the surface and there solidified with relative rapidity as a lava. The largest masses of it, however, did not reach the surface, but cooled very slowly at considerable depth under great pressure, and eventually consolidated into a rock of granitic texture. Uplifts and extensive erosion may have followed; and at the present day, in many places, thousands of feet of material have been removed, bringing to the surface the intrusive granular rocks and their once deep-seated contacts with the sedimentaries which they shattered at the time of in-

Jan 1, 1902

SHELBY M. HARRISON,* New York, N. Y. (written discussion ?).¬Your secretary requested a brief description of the Russell Sage Foundation, in order that members of the Institute, if they should desire to avail themselves of it, would know what type of service is offered to them through our institution. The foundation was established in 1907 by the gift of Mrs. Russell Sage of $10,000,000 as a capital fund, the income of which is to be spent for the improvement of social and living conditions in the United States. One of the lines of activity which the foundation has felt would lead toward this end is the development and promotion of community surveys; and because the scope and methods followed in these surveys are very similar to the scope and method of much of the institution's work in general, an idea of its main activities can perhaps be given best by describing one of our surveys. Incidentally, it may be pointed out that antecedent to the survey stand at least two important facts: first, the recognition. that communities are active, not static forces, that they develop, that changes in. material and human relationships occur continuously, and that with them come new social and civic problems which must, in many cases, be diagnosed and prescribed for anew; and second, the reality of scientific advances along lines which make possible at least some measure of solution of the problems. Evidences of these changes are abundant; many of them are found in the rapid growth of cities in the last few decades. Villages in agricultural districts, places where everybody knew everybody else, where the pulpit had been long the chief or only influence molding public opinion, where the air was unclouded by the smoke from factory stacks, where the water supply was not affected by pollution, where sunlight and building

Jan 5, 1918

By D. W. Gillmore, C. C. Wright

DEWATERING is a major problem in the preparation and utilization of fine-sized coals now being recovered in increasing amounts from colliery effluents, refuse banks, and silt ponds. Of the various methods which have, been proposed for dewatering fine coal, gravity drainage is probably the oldest and most widely used, and yet little information on this subject has been published. Consequently a laboratory investigation of gravity drainage phenomena was undertaken not only to provide basic data for predicting the drainage behavior of fine coals in cars, bunkers, basins, and silos, but also to obtain some understanding of the moisture retention properties of fine coal. Because of practical interest in the problem, a reproducible laboratory technique, which simulated plant conditions as closely as possible, was developed for the evaluation of drainage variables. The ap- paratus selected consisted of vertically-mounted lucite columns, nominally 4 to 8 ft in length and 2, 3 or 6 in. in diam; the bottom of the column was provided with a rubber stopper through which was inserted a -in. diam drainage tube; a wad of glass wool was placed on the upper part of this outlet tube to retain the coal and a plug was temporarily located at the lower end to prevent drainage during charging of the column, see Fig. 1. The most satisfactory testing procedure is as follows: 1—The fine coal, which has been thoroughly

Jan 1, 1953

By C. S. Smith, L. W. Kempf, C. S. Taylor

The thermal conductivity of aluminum alloys is of considerable industrial importance. This is particularly true in such applications as internal-combustion engines where one of the principal reasons for the use of these alloys is their relatively higher thermal conductivity. In spite of this, relatively few data are available on this property of aluminum alloys. The reason is quite apparent to anyone concerned with the experimental determination of coefficients of thermal conductivity. This determination, in theory so simple, is extraordinarily difficult if any high degree of precision is desired. Fortunately, some .knowledge of the relationship between thermal and electrical conductivity has permitted the use of the latter physical property in deducing the relative approximate values of the thermal conductivities of metals. This fundamental relationship, first enunciated by Wiedemann and Franz' as applying to metallic elements and later shown by Lorenz2 to be applicable to alloys within a single metallic system, has been of service in the industrial application of metals. The electrical conductivity of metals is easily determined with a high degree of precision. It is, therefore, quite desirable that the relationship between electrical and thermal characteristics be determined with the greatest possible precision. This paper presents data on the electrical and thermal conductivities of a number of aluminum alloys of industrial importance. Literature on Thermal Conductivity of Aluminum Alloys Masumoto3 determined the electrical and thermal conductivities of 18 aluminum alloys. His results indicated a relatively constant relationship between thermal and electrical conductivity.

Jan 1, 1937

By S. R. du Toit, W. J. Oberholzer, M. I. Watson, D. G. Krige

The objectives, essential features and implications of the 'random' and 'deterministic' types of ore value surfaces are examined as well as the basic requirements for a satisfactory prediction model. The 'random' method used on the South African gold mines and based on observed auto-covariance patterns is briefly discussed as well as its justification in preference to the 'deterministic' approach. Various mathematical models for auto-covariance patterns are examined for the one-dimensional case. It is also shown that these patterns as estimated for ore values in certain mines agree closely for various sizes of ore unit. In two case studies the variations in gold, uranium and ore thickness covariance patterns are examined and compared with certain geological features established independently from sedimentological studies.

Jan 1, 1969

By L. P. Teas

In spite of the influx of operators into the Gulf Coast anxious to retrieve their depleted production in other fields, and in spite of very active application of the most scientific geophysical methods to locate new producing areas, the results have been very discouraging and the year has failed to produce more than the average results for a Gulf Coast year. During the year seven new oil fields, some of which are still of very little importance, and one new gas area have been discovered. These fields are Tom Ball, Greta, Cleveland, Raisin and Garwood in Colorado County; Louise and Premont in Jim Wells County, and the new producing gas area near Ace in southern Polk County. During the year salt has been found for the first time at Carlos and Esperson. New producing areas have been developed on East Stratton Ridge, Hockley, Hull, Port Neches, near Pettus in Bee County, and on the O'Connor Ranch in Victoria County. The total production for the Gulf Coast for the year was 62,837,435 bbl., an increase of 18,589,000 bbl. over 1932. During the year, 1307 wells have been drilled of which 207 were wildcats, compared with 653 wells and 141 wildcats the previous year. The total daily production at the end of the year was 165,201 bbl. At present there are 3100 oil wells producing. The average production per well is 55.5 bbl. per day. The price of crude fluctuated considerably during the year, beginning at 80c per barrel and closing the year at $1.04 per barrel. Completion data for 1933 are as follows:

Jan 1, 1934

By W. F. Carew, F. A. Crossley

IT has been reported that the Ti-8 pct A1 alloy is ductile as water quenched from 800°C but brittle as annealed at 650 °C." The present, somewhat limited, investigation was undertaken to discover the cause of the embrittlement. In order to evaluate to some extent the continuity of the embrittling phenomenon, alloys of 6, 8, and 10 pct A1 were studied. Subsequent to the completion of most of this work, Ence and Margolin reported that a Ti,A1 phase exists and that two or more unidentified compounds may exist in the Ti-A1 system.' Materials, Equipment, and Techniques The alloys were prepared using Kroll process sponge of 124 Bhn hardness. In addition, some 8 pct A1 material was made with iodide titanium. The sponge-base alloys were prepared as melts of 4 lb or more by double arc melting. The iodide Ti-8 pct A1 alloy was prepared as 200-g buttons. The alloys were forged at temperatures of 980" to 1150°C. Results of chemical analyses are given in Table I. A Baldwin-Southwark 60,000-lb capacity tensile machine, equipped with an autographic stress-strain recorder, was used for the tensile tests. Standard tensile test specimens, 0.252 in. diam, were used. Standard Charwy V-notch impact specimens were tested using a -kiehle machine. specimens were sealed in evacuated Vycor bulbs for heat treatment. Powder samples for Debye-Sherrer anal- ysis were prepared by filing and screening through 325 mesh. The —325 mesh fraction was taken in an effort to concentrate a microstructural constituent assumed to be less ductile than the a phase. The powder samples were stress relieve2 by annealing

Jan 1, 1958

By E. G. Leonardon, C. Schlumberger, M. Schlumberger

Last year the authors presented a paper that discussed the various electrical measurements they perform in drill holes, which they name "electrical coring."' The object of the present paper is to give a brief account of the points of scientific interest that have been elucidated by further field work and laboratory research, as well as the economic results that have been attained recently. The practical examples given in this paper are drawn, for the most part, from the field work performed in Russian oil fields during the years 1931 and 1932. This is due to the fact that, thanks to the comprehensive cooperation of the Russian geologists and scientists, the authors are allowed to make public a large amount of recant information. In other countries in which the authors are engaged in similar work, the competition between private companies makes it imperative, for a considerable lapse of time, to avoid publication of the results obtained. The following points will be discussed successively, under separate headings: 1. Electrochemical phenomena in drill holes. 2. Stratigraphic correlations and tectonic studies. 3. Relations' between the productivity of oil horizons and their electrical resistivity. 4. Location of coal seams. 5. Summary and conclusions. Electrochemical Phenomena in Drill Holes Technical Publication 462l described the author's discovery concerning the existence of important differences of potential spontaneously gener-

Jan 1, 1934

By C. K. McArthur

THE subject of classification is so broad that this discussion is confined to what the author believes is of prime importance in connection with proper grinding and classification. The years passed have witnessed many noteworthy changes in fine grinding and classification, which have been accompanied by a readjustment of ore-dressing flowsheets for the preparation of better ground and/or sized products at an expenditure of less power, steel and maintenance than formerly. Nowhere in the industry is more being done in the way of experimental work to lower costs than in grinding circuits, because, at best, grinding costs are high. Recent years have indicated that, on the average, finer grinding has a real application. Without careful preparation of the process feed, no operation can be highly efficient or successful. In an earlier paper, the findings of an extensive survey at representative concentrators were presented1. Also, in the year of 1935, a technical discussion was given by Dr. J. V. N. Dorr (Some Notes on Classification Trends in America) before the Chemical, Metallurgical and Mining Society of South Africa In both papers mentioned, much has been said regarding flowsheets, grinding and classification. The author is very familiar with these papers, having had considerable to do with the actual operation of the flowsheets, as well as large mills and classifiers in the work described. Some data from the second paper have been included in the following discussion. Circulating Load In this particular paper it seems advisable to deal with the classification phases of the work that to a major extent govern the success of any closed-circuit grinding unit. The question has often been asked in connection with a closed circuit: "What circulating-load ratio should be carried?" This is really an

Jan 1, 1937