Search Documents

By J. Grosso, D. J. Nagel

In many metallurgical studies, it is necessary to reveal the composition and structural properties of materials. Usually this is done by etching, but some substances do not etch well or easily. Anodizing is known to provide an alternate treatment in many cases. In general, this technique is simple, often more sensitive to composition differences than etching, has excellent resolution, and provides variable contrast in those elements and alloys which anodize. Here we report the use of anodizing in diffusion studies in the TiCb system. Fig. 1 shows a cross section of the diffusion zone in a TiCb couple. The anodizing has clearly revealed both composition and crystallographic features. The maximum bulk penetration of the titanium into the columbium is marked by a sharp line because of the steep concentration gradient. The titanium grain size and orientation differences are also evident. Variation in the grain size reflects the gradually decreasing columbium concentration.

Jan 1, 1967

By Janshi Sen

VERTICAL-INTENSITY magnetometers, such as the Hotchkiss Superdip and the Askania vertical field balance, are now [ ] widely used, because vertical-intensity charts give definite information for the location of upper pole, dip and strike, and approximate shape of the deposit. Again, a slow and steady increase of dip over a large area indicates a large deep-lying deposit, while a large dip limited to a small area and falling away rapidly suggests a small and shallow one. The complication comes more from the richness of the ore. A large body of lean ore near the surface might produce the same vertical-intensity chart as a rich ore at depth. This paper presents a method for calculating the maximum depth of a single-pole deposit and another for a two-pole mineral body, by utilizing data of both vertical and horizontal intensities as obtained by a Thalen-Tiberg magnetometer. As shown on the left side of Fig. 1, lean ore, rich ore and a single pole produce the same magnetic field. The depth of the pole, [ ] h, can be calculated from the following relation: [h=a=tan¢=G-F h=aXFy] where G is the vertical intensity at point A due to the pole; F, the horizontal intensity of the same; and a, the distance from the point of maximum vertical intensity or the vertical projection of the pole on the surface to the point of observation A. If an entirely covered deposit is indicated by magnetic measurements and boring cost estimated from the calculated depth is so reasonable as to encourage drilling, the ore should be struck somewhere within the limit of the calculated depth by the borehole. A number of such points as A should be taken for calculation, erratic results should be rejected and the average figure used for cost estimation.

Jan 1, 1944

By Edward Martinez

Although the copper segregation process has been known as a method for treating oxide copper ores since the 1920's, the reactions involved in this process are still a matter of conjecture. However, the evidence turned up in a recent series of experiments at Asarco's Central Research Laboratories strongly indicates that some of the proposed reactions may not be occurring. Experimental work on oxide copper ores from the Sagasca mines in Chile led to the discovery of the copper segregation process in 1923. It was found that the reduction of the copper with coal at about 700°C occurred on the surface of the coal instead of remaining disseminated in the ore. The unusual behavior of the copper, which caused it to migrate from the ore particles to the coal, was traced to the presence of a small quantity of sodium chloride occurring in the ore. Further experiments with oxide copper ores proved that the presence of a halide, either occurring naturally or admixed with the ore, caused the copper to migrate from the ore particles and to segregate in the charge.

Jan 8, 1966

By Robert G. Van Nostrand, John H. Henkel

TRANSIENT potentials obtained in resistivity prospecting can be separated into two classes. The first is electromagnetic, has a comparatively short time constant, and increases in relative amplitude as the electrode separation is increased. These electromagnetic transient potentials, of which an excellent theoretical treatment is given by Yost: are the result of changes in the current and can be classed as differentiated signals. The second class is electrochemical, has a comparatively long time constant, and decreases in relative amplitude as the electrode separation is increased. The electrochemical signals are generated by the current flow itself and can be classed as integrated signals. The transient potentials due to electrochemical factors are the subject of this article. The phenomenon is referred to as induced polarization. Schlumberger" was the first worker to observe induced polarization, but he was unsuccessful in attempts to apply the principles of induced polarization in electrochemical prospecting. Other workers, notably Bleil; have studied polarization and in some cases pointed out its possibilities, but no theory has been presented that describes polarization and its time dependence adequately. It is the purpose of this discussion to present the essence of a theory to geo-physicists and to show that it leads to results consistent with experimental evidence. The theory on which this analysis is based has existed in electrochemical circles since 1910."

Jan 1, 1958

By Bernard Moore

THE last few decades have witnessed the introduction of many new nonmetallic mineral products and changes in the use of many of those already well known. Among these is diatomite, formerly employed as a mild abrasive and, at one time, as the absorbent material in dynamite. Now nearly 100,000 tons a year are mined and milled into such things as filter aids, cement admixtures, insulants, fillers, absorbents, cosmetics, cleansers, etc. Pumice, commonly regarded as only an abrasive, is now also employed as an insulant, as light-weight aggregate and as a concrete admixture. With increasing use of insulants, light-weight aggregates, and acoustic stuccos and plasters in the building trades, both these mate-rials should find increased application. Very large deposits occur in eastern Oregon and have been studied by the U. S. Geological Survey in cooperation with the Oregon State Mining Board.

Jan 1, 1934

By Richard D. Call

Predicting the performance of a waste embankment requires an estimate of the properties of the waste and foundation materials. The performance characteristics and the associated material properties are: [ ] Methods for obtaining estimates of the material properties include: laboratory and field testing, back analysis, and indirect estimates from other material properties. The most critical technical need is the development of indirect methods for use in feasibility studies and mine planning, prior to production when actual samples of waste material are not available. Material properties are not unique, single values; they are probability distributions. There are two components to these distributions: the uncertainties in testing and the inherent variability of the material. The objectives of a material properties evaluation should be to obtain an unbiased estimate of the property distributions rather than the average or the minimum value. Whether the current trend to a probability design analysis is followed or a simple sensitivity analysis is conducted, the unbiased probability distribution is preferable to single values.

Jan 1, 1985

By E. Werchowsky

FOR over four years, since the revolution of 1917, Russia has been cut off from the Western world. Political and general economical reforms have attracted the attention of the public and business world, but mining men have had no information as to the situation in their branch of industry, as various articles which have appeared in the European and American press gave little information as to actual conditions in our country. When the Soviet system of government was estab-lished and private ownership abolished, it affected the FIG. 1.-ORGANIZATION OF THE COUNCIL OF MINES. mining industry very little at first. The power of the Soviets did not affect the Ural provinces nor Ukraine or Asiatic Russia (Siberia, Turkestan, etc.) during 1918 and 1919, and, as is well known, the mineral wealth of the republic lies within those boundaries. In the Ural Mountains are copper, gold, and platinum; in Siberia, silver, lead, zinc, and gold, and the coal deposits in Koushetz district; in Ukraine, there are the coal fields of Donetz and the iron mines of Krivvy Rog, and silver, lead, zinc, copper, oil, etc. in the Cauca-sus. The mineral resources of Central Russia are the coal fields of Moscow (low-grade and brown coal), turf deposits, iron mines in Tula and Kalonga provinces, and quarries of granite and other building materials.

Jan 8, 1922

By John Suman

DURING the past few years the taking of cores in drilling with rotary equipment has been perfected to a remarkable degree in the Gulf Coast fields of Texas and Louisiana. Taking of cores is becoming quite a common thing, especially in the newer fields, and drillers are becoming expert in this work. The writer has seen cores 5 to 8 ft. long taken with great ease in wells as deep as 4500 ft. Coring is doing much to remove the prejudice which so many petroleum engineers seem to have against .the use of rotary drilling equipment for exploratory work. Some operators .are now claiming that when used with a reasonable amount of coring the rotary system is even more satis-factory than cable tools for exploring in certain territory. A case has recently been pointed out in the South Electra field of North Texas, where producing oil sands, passed over by cable-tool drillers, are being brought in with rotary equipment. It seems that in this particular territory the sands are rather thin. Cable-tool drilling was carried on for the most part in a wet hole and the red mud encountered in drilling caved into the hole very badly, so that the cuttings showed mostly red mud and the driller, thinking that the sand did not amount to anything, carried his water string through the sand. The later .operators, drilling into the sand with rotary equipment and coring it, found that it was well worth testing.

Jan 10, 1922

By R. L. Templin, D. A. Paul

The modulus of elasticity is defined as the ratio of stress within the proportional limit to corresponding strain. This property, as thus defined, is a constant for each kind of material; and in tension or compression is usually designated by the symbol E. The modulus of elasticity serves as an index of the stiffness of a material or a measure of its ability to resist change of shape under stresses not higher than the proportional limit. In view of the frequency with which the modulus of elasticity is used in engineering calculations, it is surprising to note the uncertainty that exists as to authentic values, and the marked lack of published information relating to the variation of the constant E within individual alloy systems. A value of 10,000,000 Ib. per sq. in. has been quoted as representative of aluminum and its alloys. This value has been found to be approximately corrcct for pure aluminum and aluminum alloys in which the total percentage of the alloying elements is low, but seriously in error in the case of alloys that contain relatively large amounts of the alloying elements. a National Metals Handbook. b Intcrnatiunal Critical Tables. '' Aluminum Co. of America. " Based on density of alurminum (2.70). c Smithsonian Pliysical Tables.

Jan 1, 1931

By Rudolph G. Wuerker

MUCH descriptive matter[ ] has appeared on the subject of suspension roof supports, or roof bolting, as it is more commonly called. The wide- spread introduction of roof bolting into coal mines and metal mines is truly phenomenal. Mine operators were quick to recognize the advantages of supporting wide openings without hindrance to machine maneuverability and ventilation.

Jan 6, 1953

By Earl R. Hoskins, James E. Russell

The electrical resistivity of rocks has been studied quite extensively, in particular, the effects of temperature and confining pressure on resistivity. References 1 through 6 at the end of this chapter pertain to electrical resistivity of rock and contain further references on the same topic. The present study is motivated by an interest in determining the in-situ properties of rock as well as the stress state of the rock and how these quantities are changing with time. Most of the previous work on the electrical resistivity of rocks has been directed toward saturated rocks at relatively high confining pressures and temperatures. The present study was oriented towards air-dry surface rock that might occur in mine pillars. The mean stress and temperature under such conditions are comparatively low. It has been demonstrated that the resistivity of rock is highly dependent upon the porosity. In fact, for saturated rocks, a relationship referred to as Archie's law has been established between porosity and electrical resistivity. In the case of saturated rock, the property that is actually being measured is the resistivity of the solid/fluid system. Since the resistivity of the fluid alone is usually much lower than that of the dry rock, it is understandable that the resistivity of a saturated rock is in general several orders of magnitude lower than the resistivity of a relatively dry rocli. For dry rock, it seems reasonable that the electrical resistivity should increase as microcracks open within the material. Since microcracks open as material is stressed closer and closer to its failure point, it appears that there should be a correlation between electrical resistivity

Jan 1, 1970

1938 ABERNATHY, G E Feb 6, 1948 Min & Met Apr 1948 1937 ADAMS, ARMY Aug 20, 1949 Min Eng Dec 1949 1946 ADDY, GEORGE E Sept 24, 1950 Min Eng July 1951 1920 ALDERSON, WILTON P Feb 1951 Min Eng Sept 1952 1896 ALDRICH, T H , JR May 24, 1950 Min Eng Aug 1950 1942 ALDRIDGE, LEONARD June 8, 1952Jrn Met Sept 1952 1919 ALLEN, ROLLAND C July 18, 1948 Min &Met Sept 1948 1950 ANDERSON, C P Unknown Min Eng Feb 1951 1937 ANDERSON, JOHN H May 10, 1950 Min Eng Aug 1950 1914 ANDERSON, L DOUGLASS Unknown Min Eng Nov 1951 1948 ANDRAU, E W K Oct 20, 1951 1936 ANDREWS, CHARLES B Apr 19, 1950 Min Eng June 1950 1918 ARMITAGE, PAUL June 28, 1949 Min Eng Oct 1949 1924 ARMSTRONG, PERCY A E Jan 23, 1949 Min Eng May 1949 1906 ARNOLD, CHARLES LE NEVE Aug 7, 1949 Min Eng Oct 1949 1945 ARNOLD, HAROLD S Aug 7, 1950 Min Eng Oct 1950 1936 ASH, JAMES E Dec 17. 1949 Min Eng Apr 1950

Jan 1, 1952

By Herbert Haas

GEORGE W. HAWKINS, Tucson, Ariz. (communication to the Secretary*).-The paper by Mr. Haas will no doubt be followed with considerable interest, as it covers the power-plant problem in quite a comprehensive way, including not only the usual operating costs but also the fixed charges on the investment, and for load factors ranging all the way from 25 to 100 per cent. and fuel oil ranging from $1.25 to $2 per barrel. The very fact, however, that his paper does cover such a wide range of conditions, makes it the more imperative that any conclusion drawn from his analysis be very carefully considered for any specific case, for in making such analysis the type of prime mover and size must be selected for some one condition which might not be the proper selection had some other condition been assumed as the basic one, resulting in an unfavorable comparison under all conditions except that condition assumed. From the reasons given by the author for his selection of the large turbine units, it is evident he had in mind very high load factors, ranging

Jan 12, 1916

By Sylvain J. Pirson

The number of seismograph field crews employed in the active survey of potential oil territories is still on the increase, owing to the ever pending threat of a shortage in the supply of crude oil. It is to be expected that for years to come the seismograph will be responsible for discovering many new oil fields, both in wildcat territories and in deeper formations, and that the seismographic campaign will go on unabated. Yet improvements in instrumental design, in the field and interpretative techniques, are brought about year after year, and lead to the reshooting of areas many times surveyed previously. Notwithstanding the experience gained by the past eight years of active work in reflection seismographic surveys, the results given by this method of mapping deep formations have in many instances been at variance with the information subsequently obtained by the drill. To overcome this shortcoming, geophysicists have used closer spacing of the shot points and closer control of the depth points. The method discussed here is being used actively in the Mid-Continent region and endeavors to reduce the interpretation work to a mere mechanical technique, leaving as little as possible to the opinion of the interpreter. The New Method Field Technique.—In sectionized territory where country roads are available every mile, shot points are preferably located every 1/4 mile when six detectors are available or every % mile when eight detectors are at hand. The disposition of individual spreads is represented on Fig. I; in each case a shot point is located at the section corners. Fig. 2a represents the layout of a spread between shot points, the vibration detectors being preferably equidistantly located. Normally in the 1/4-mile control, the distance between shot points is 1320 ft. and the distance between detectors 220 ft. When shooting from shot point S.P. I, detectors 1 to 6 are connected to the recording galvanometers and detector 0 (which indicates the vertical travel time of the wave corre-

Jan 1, 1940

By J. E. Lawver, R. R. Beebe, J. L. Wright

This paper describes a separation coefficient Ks useful as a "measure of goodness" to be used in factorial and response surface methodology. The use and limitations of the separation coefficient is discussed, and a computer program for calculating the coefficient is presented (in Fortran). The application of the coefficient is illustrated in terms of electro-dynamic separation of Mesabi semitaconites. Present Mesabi wash ores and gravity concentrates with an iron to silica ratio of only 5 or 6 to 1 are no longer readily salable, for the steel industry now demands concentrates with an iron to silica ratio of at least 10 to 1 and a structure comparable to pellets. THE ELECTRODYNAMIC-FLOTATION PROCESS Wash ores and gravity concentrates consist largely of hematite, goethite, and quartz. Several methods of beneficiation are being tested at the University of Minnesota Mines Experiment Station with a view to improving the salability of these materials. A process that looks particularly promising from an economic view is the combination electrodynamic-flotation process shown in Fig. 1. This process is designed to upgrade gravity concentrates to a 5% silica content and to provide fines — from the flotation circuit —to permit agglomeration. Although electrodynamic concentration of specularite is an established and well-understood process, the electrodynamic concentration of Mesabi goethite-hematite gravity concentrates presents interesting and enigmatic problems. The gravity concentrates are by no means assemblages of clean, free mineral particles. Instead, the concentrates to be retreated consist of a great variety of middlings. More or less complete liberation would require grinding to minus 325 mesh, at which size only flotation could be expected to function, and even then grades and especially recoveries would not be satisfactory. A close examination of the gravity concentrates shows that grinding to 100% minus 48 mesh will produce a product which is approximately 70 weight % plus 325 mesh (see Fig. 1). The remaining 30 weight % can be deslimed and floated by conventional methods, but the resulting iron concentrate is

Jan 1, 1964

By Sylvain J. Pirson

The number of seismograph field crews employed in the active survey of potential oil territories is still on the increase, owing to the ever pending threat of a shortage in the supply of crude oil. It is to be expected that for years to come the seismograph will be responsible for discovering many new oil fields, both in wildcat territories and in deeper formations, and that the seismographic campaign will go on unabated. Yet improvements in instrumental design, in the field and interpretative techniques, are brought about year after year, and lead to the reshooting of areas many times surveyed previously. Notwithstanding the experience gained by the past eight years of active work in reflection seismographic surveys, the results given by this method of mapping deep formations have in many instances been at variance with the information subsequently obtained by the drill. To overcome this shortcoming, geophysicists have used closer spacing of the shot points and closer control of the depth points. The method discussed here is being used actively in the Mid-Continent region and endeavors to reduce the interpretation work to a mere mechanical technique, leaving as little as possible to the opinion of the interpreter. The New Method Field Technique.—In sectionized territory where country roads are available every mile, shot points are preferably located every 1/4 mile when six detectors are available or every % mile when eight detectors are at hand. The disposition of individual spreads is represented on Fig. I; in each case a shot point is located at the section corners. Fig. 2a represents the layout of a spread between shot points, the vibration detectors being preferably equidistantly located. Normally in the 1/4-mile control, the distance between shot points is 1320 ft. and the distance between detectors 220 ft. When shooting from shot point S.P. I, detectors 1 to 6 are connected to the recording galvanometers and detector 0 (which indicates the vertical travel time of the wave corre-

Jan 1, 1940

By Wilder D. Bancroft

It is eight years since I have been connected actively with metallography, but in this time I have been learning something about colloid chemistry, which may be considered as the chemistry of bubbles, drops, grains, filaments, and films, all things in which at least one dimension is very small or in which the surface is large relatively to the mass. Films, of course, suggest to the metallographist Beilby's amorphous film theory, about which I am going to speak for a while, though probably not in the way you expect. I come to bury Beilby, not to praise him. So far as I can judge from looking over the literature hastily, there are two schools in the United States, those who accept Beilby's theory willingly and those who accept it unwillingly. Hoytl says that: At present there seem to be two schools in metallography, one which has adopted the amorphous-phase theory for the explanation of the effect of cold work, mechanical deformation, etc., and one which is not ready at present to adopt this theory. It seems to me that this theory can at least be used as a convenient means of explaining various facts that are demonstrable in the laboratory but the presence of this amorphous material, through our lack of experimental means, we are unable to prove. That we have failed in this direction should not necessarily hinder us from using a theory as workable as this. Mathewson2 says: I have come reluctantly to believe in the amorphous theory, or some theory admitting a modification of the ordinary crystalline phase so as to permit differential properties with temperature, etc. If Mathewson represents one extreme, with Hoyt perhaps occupying a middle ground, H. M. Howe3 may be cited as one of the enthusiastic supporters of Beilby's amorphous theory. It is, says Howe:

Jan 1, 1923

By Wilder D. Bancroft

It is eight years since I have been connected actively with metallography, but in this time I have been learning something about colloid chemistry, which may be considered as the chemistry of bubbles, drops, grains, filaments, and films, all things in which at least one dimension is very small or in which the surface is large relatively to the mass. Films, of course, suggest to the metallographist Beilby's amorphous film theory, about which I am going to speak for a while, though probably not in the way you expect. I come to bury Beilby, not to praise him. So far as I can judge from looking over the literature hastily, there are two schools in the United States, those who accept Beilby's theory willingly and those who accept it unwillingly. Hoytl says that: At present there seem to be two schools in metallography, one which has adopted the amorphous-phase theory for the explanation of the effect of cold work, mechanical deformation, etc., and one which is not ready at present to adopt this theory. It seems to me that this theory can at least be used as a convenient means of explaining various facts that are demonstrable in the laboratory but the presence of this amorphous material, through our lack of experimental means, we are unable to prove. That we have failed in this direction should not necessarily hinder us from using a theory as workable as this. Mathewson2 says: I have come reluctantly to believe in the amorphous theory, or some theory admitting a modification of the ordinary crystalline phase so as to permit differential properties with temperature, etc. If Mathewson represents one extreme, with Hoyt perhaps occupying a middle ground, H. M. Howe3 may be cited as one of the enthusiastic supporters of Beilby's amorphous theory. It is, says Howe:

Jan 1, 1923

By W. H. Craigue

THE scope of this article covers only the mathematical principles involved in discounting to present worth future expected profits and it is believed answers definitely two questions, which were raised at a recent meeting of the Committee on Methods of Valuing Coal Properties, as follows: 1. The accumulative effect of carrying charges on the value of coal mines showing definitely the number of years beyond which the coal may not be mined at a profit and subsequent to which the possession of any unmined coal will be a liability rather than an asset. 2. The effect on the valuation of coal mines, in the presence of the carrying charges described in question 1, of an increase in plant capacity and production. In general, in considering these questions, it may be stated that the consideration of an increase in plant capacity and production follows as a matter of course after a determination has been made of the year beyond which no profits are to be realized (giving the carrying. charges accumulative effect, or in other words capitalizing the carrying charges, as shown hereinafter). For example, if it is determined that any coal that is unmined after 45 years will have no value or less than no value, the question immediately arises as to whether or not a plant should be constructed that would result in a yearly production great enough to extract the entire tonnage in a time less than 45 years, and if so the number 'of years less than 45 years that would, from a financial stand-point, be the most desirable, all under the assumption that the market for the product or the transportation facilities are such that the yearly production can be increased to the desired amount.

Jan 1, 1933

By J. H. M. Thomeer

A method is presented that provides a mathematical description of capillary pressure curves and, probably, of differences in pore geometry of samples. The technique is based on the observation that the location and shape of a capillary pressure curve reflect characteristics of the pore structure of the sample. INTRODUCTION It has been noted1-5 that the observed differences in shape and location of capillary pressure curves reflect some basic properties regarding the pore geometry of the samples. For example, according to basic concepts of capillarity, the following statements can be made regarding the location and shape of a capillary pressure curve.* The location of the curve with respect to the (Vb)pc and PC axes is a measure of the interconnected pore volume and of the cross-sectional area of the pore first entered by mercury, respectively. The shape of the curve depends on the interconnection of the pores and the sorting of the pore sizes. It has been the object of this study to use this information as a starting point in an attempt to find a unique mathematical description of the PC — (Vv)p, relations of different samples. It may be expected that parameters in such a relation can then be used to describe differences in pore geometry of these samples. For a practical description of the PC — (Vb)p, relation, however, it appears desirable to describe each curve (i.e., each sample) by a limited number of parameters so that the curves taken from all samples form a family, each member of which is uniquely determined by one single combination of values of all parameters.