Search Documents

By T. M. Morris

THE rate of flotation of solid particles determines the percentage recovery of these particles which can be obtained during a given time interval. It is an established fact that the recovery is greatest in the fine sand size range and falls off on either side of this size range. It is also a fact that the history of the development of concentrating devices has been marked by a desire to recover the small particles: tables were developed to treat material too fine to recover in jigs; flotation recovers material too fine to be recovered on tables. As our ores become more complex and require finer grinding, a greater proportion is in the slow-floating size range. It is therefore of economic importance that the effect of size of particle upon rate of flotation be studied. Many studies have been made along this line. The present investigation attempts to quantify the rate of flotation by means of a rate equation, and then compares the effect of size upon the rate of flotation. It was found that the flotation rate constant increases with increase in diameter of particle in the size range smaller than the optimum size particle. The flotation rate constant decreases with an increase in diameter of particle in the size range coarser than the optimum size particle. This suggested two different actions taking place, and these are discussed. Suggestions for further work in order to improve the flotation rate of both fine and coarse particles are made. The usual method of expressing rate is to plot cumulative percent recovery vs time. If we knew the equation of this kind of curve we could replot it as a straight line, and the slope of the line would be an index of the magnitude of the flotation rate. It is easier to compare straight lines than curves. The basis used for obtaining the equation of the recovery vs time curve is the law of mass action. This law states that the "rate of a chemical reaction is proportional to the 'active masses' of the reacting substances present at any given time." This, of course, implies a constant temperature. We can modify this for our use by using the term flotation reaction instead of chemical reaction and the term floatable particle instead of active masses. dC Thus----— kc [1] where C denotes concentration of particles, t denotes time, k denotes a proportionality constant. If the exponent of C is 1, then we have a first order rate reaction. If the exponent of C is 2, then we have a second order rate reaction. For a first order rate reaction, we obtain, after integration, where k is again a proportionality constant and has the dimension of the reciprocal of time. C, is the original concentration or weight or percentage of floatable particles. C, is the concentration or weight or percentage of floatable particles remaining in the flotation cell after time t. If all particles of the mineral to be floated were capable of floating we could take C, as 100 and C, would be 100 - R, where R is the cumulative percentage recovery of mineral at time t. But it is not usual for all of the particles to be capable of floating, because of surface oxidation, etc. Therefore, we must introduce a factor x which is the percentage of un-floatable mineral. Hence the first order equation is It has been proposed by various workers1-' that this equation describes the flotation rate. More recently N. Arbiter4 states that a second order rate equation fits the recovery vs time curve more closely than does a first order rate equation. Morris- as discussed the evidence presented for this statement. It has been concluded that the first

Jan 1, 1953

By Thomas H. Leggett

IN speaking of the mining and economic conditions prevailing at the present time on the Rand, it is not my intention to go into the details of the mining-practice, since this has been already well described both in the Transactions1 and elsewhere,2 but rather to take a more comprehensive view of the industry and its surroundings as a. whole, marking its general development and the lines of its future progress. In a. paper entitled Deep-Level Shafts on the Witwatersrand, with Remarks on a Method of Working the Greatest Number of Deep-Level Mines with the Fewest Possible Shafts,3 presented to this Institute in August, 1900, I drew attention to the great cost of sinking the very deep vertical shafts that were then being seriously proposed as necessary for the development of the deeper areas, pointing out the strong advisability of working this ground by means of inclines to be sunk from the existing shafts of from 3,000 to 4,000 ft. in vertical depth. In this paper it is stated (1:). 975): "In short, practice upon the Rand now tends towards fewer vertical shafts and more underground inclines, especially for the very deep mining about to be undertaken." In consequence, the 6,000-ft. vertical shafts, at one time so much discussed, have never been started, and they do not now seem likely ever to be. The necessity of placing all deep shafts further apart in order to make them control and exhaust larger areas was also dwelt upon. This economy was vitally necessary for both 1 Gold-Mining in the Transvaal, South Africa, John Hays Hammond, xxxi., S17 to 855 (1901). R Engineering and Mining Journal, vol. lxxxv., p. 53 (1908). ' Trans., xxx., 947 to 987 (1900).

Jan 5, 1908

By T. B. Counselman

C. G. McLachlan—In the foregoing paper the author has presented a very neat method for calculating the solution recovery for a countercurrent flowsheet. He has, however, based his calculations, as he states, on the assumption that "the concentration of dissolved value must be exactly the same in the overflow and underflow of any thickener." This assumption, which is usually made regardless of the type of calculation used, is "not strictly correct because diffusion of the dissolved gold in the solution associated with the solids as it progresses through the countercurrent system is far from being instantaneous, with the result that on a ton for ton basis, the assay of the solution in the thickener underflow is higher than in the corresponding thickener overflow. An agitator introduced into the flowsheet between thickeners will reduce, but not entirely eliminate, this difference. In practice we have found that the best way to take care of this condition— in addition to the use of one or more intermediate agitators—is to circulate 20 pct or 25 pct more solution than called for by the cheoretical calculation. This presents no difficulty provided that adequate thickener capacity is provided in the original design of the countercurrent circuit.

Jan 1, 1951

By Elliot P. Rexford

B. C. Burgess-—Prior to hearing this paper presented at the San Francisco meeting, I travelled by car from Yuma, Ariz., across south-central California and up through the San Joaquin Valley. After hearing the paper I returned by the coast route to San Diego then along the Mexican border to Yuma. The striking feature of these trips, related to this paper, was the dry river and creek beds at a time of year not the dry season. Contrasted with this was the wasteful use of water in irrigation canals and laterals. Poland says "at least 90 pct of the ground water pumped is used for irrigation." That being the case, it would appear that first consideration should be given to conservation of this use. Probably a small part of this is actually reaching the plants. Some measure of this loss between pump and crops would be revealing. Methods that might be employed to reduce this loss are pipe lines and spraying of some crops such as the banana planters are using in Central America. Another idea which might be investigated is to line canals and ditches with some water-repelling mineral like pyro-phyllite. Perhaps a comparatively thin sprayed-on

Jan 1, 1951

By Elliot P. Rexford

B. C. Burgess-—Prior to hearing this paper presented at the San Francisco meeting, I travelled by car from Yuma, Ariz., across south-central California and up through the San Joaquin Valley. After hearing the paper I returned by the coast route to San Diego then along the Mexican border to Yuma. The striking feature of these trips, related to this paper, was the dry river and creek beds at a time of year not the dry season. Contrasted with this was the wasteful use of water in irrigation canals and laterals. Poland says "at least 90 pct of the ground water pumped is used for irrigation." That being the case, it would appear that first consideration should be given to conservation of this use. Probably a small part of this is actually reaching the plants. Some measure of this loss between pump and crops would be revealing. Methods that might be employed to reduce this loss are pipe lines and spraying of some crops such as the banana planters are using in Central America. Another idea which might be investigated is to line canals and ditches with some water-repelling mineral like pyro-phyllite. Perhaps a comparatively thin sprayed-on

Jan 1, 1951

By T. B. Counselman

C. G. McLachlan—In the foregoing paper the author has presented a very neat method for calculating the solution recovery for a countercurrent flowsheet. He has, however, based his calculations, as he states, on the assumption that "the concentration of dissolved value must be exactly the same in the overflow and underflow of any thickener." This assumption, which is usually made regardless of the type of calculation used, is "not strictly correct because diffusion of the dissolved gold in the solution associated with the solids as it progresses through the countercurrent system is far from being instantaneous, with the result that on a ton for ton basis, the assay of the solution in the thickener underflow is higher than in the corresponding thickener overflow. An agitator introduced into the flowsheet between thickeners will reduce, but not entirely eliminate, this difference. In practice we have found that the best way to take care of this condition— in addition to the use of one or more intermediate agitators—is to circulate 20 pct or 25 pct more solution than called for by the cheoretical calculation. This presents no difficulty provided that adequate thickener capacity is provided in the original design of the countercurrent circuit.

Jan 1, 1951

By J. R. Linney

A HISTORY of the ore-mining and iron-smelting industry of the Adirondacks comprises a century and a half of pioneering by rugged individualists, both men and women. By geographical location, the climate is most severe-long, cold winters with heavy snowfall, and short seasons of vegetation growth; this, together with its remote location from large centers of population, adds considerably to the difficulties of conducting mining operations in this area.

Jan 1, 1943

By R. H. Card

THE geophysicist is interested greatly in the resistivities of different formations or parts of the earth's crust; sometimes he is interested in a single figure in the nature of an average, or what may be called the effec-tive resistivity, of all the formations or parts of the crust at a given location to a certain depth. Conversely, the engineer whose work is concerned with the coordination of power and communication lines in such a manner as to avoid electrical interference between these two types of facilities is concerned very much with this effective resistivity; to a lesser extent he is interested in the resistivities of individual forma-tions. In connection with his work the coordination engineer often estimates the effective resistivity; of the earth from measurements of the mutual impedances of lines; in other instances he derives front measure-ments of a different type the resistivities of different layers of the crust and synthesizes these to obtain an estimate of the effective resistivity. In connection with problems concerning the coordination of power and telephone lines, measurements from which earth resistivities can be estimated have been made at many points in the United States by the American Telephone and Telegraph Co. and its associated companies, in cooperation with various power companies and with railroad companies having electrified sections of line. Other such measurements have been made by the Joint Subcommittee on Development and Research of the Edison Electric Institute and the Bell Telephone System. A study has been made of the correlation of these data with the ages and types of materials of the strata of the earth's crust at each of the test locations. The purpose of this study has been primarily to provide information to assist in predicting the order of magnitude of effective resistivities to be used in the preliminary consideration of problems con-cerned with the coordination of power and communication lines. To make the results of such a study, most useful, it is essential that the geo-logical data to be secured when such a prediction is wanted be readily obtainable. Data on the ages of strata and the types of materials com-posing geological structures can usually be obtained, therefore particu-

Jan 1, 1937

By John Greenawalt

IN view of the increasing importance of sintering in the beneficiation of iron ores preparatory to their reduction in the blast furnace, the writer believes the time is opportune for an up-to-date, though brief, discussion of the general principles of sintering, as well as a discussion of some of the recent improvements and mechanical developments that have been achieved in this industry, its present trend and future possibilities. Sintering may be defined as the agglomeration of fine mineral particles into a porous mass by incipient fusion caused by heat produced by com-bustion within the mass itself. Its first successful application, in connec-tion with the treatment of lead sulphide ores, was known as blast roasting. In this process the lead ore was given a preliminary roasting in a reverber-atory furnace, then the incandescent mass was placed in a pot with a grate and an updraft was applied. It was soon discovered that much better results were obtained by cooling the ore, moistening it, and placing it upon an incandescent layer of fuel previously placed upon a grate, and then applying the updraft blast of air until the charge was converted into a more or less agglomerated mass. The fuel was sulphur and the process one of desulphurization, which was the principal result desired. The application of downdraft to blast roasting brought about tremen-dous results; the principal one of which was that an air blast of high pressure could be passed through a layer of ore deposited on a grate, or on a grate covered by a layer of coarse porous material, without disturbing the particles of which the layer is composed. The air current is compelled to filter through the pores of the charge, whereas if the same pressure applied to the top surface of the charge with downdraft were applied to the bottom of the charge with updraft, the charge would be completely blown off the grate. Another result of reversing the draft was that a flame could readily be applied to the top surface of the charge for ignit-ing purposes.

Jan 1, 1938

By H. W. Camp

ALTHOUGH the situation in the oil industry during the past year has. not been conducive to large expenditures for development and research, there is little indication that such expenditures have been curtailed. While few outstanding achievements have been reported, considerable progress has been made in the development of new products and the adaptation of petroleum derivatives to new uses. The most important question facing the refiner today is the anti-knock quality of his gasoline. This year has seen the widespread adoption of the term "octane number" as a measure for anti-knock values, and in the latter months of the year the public has been made acutely aware of this condition through competitive advertising. Gaso-line is no longer priced on volatility and gravity alone, but on octane number as well; and premiums are being paid for material of relatively high octane rating. The situation has grown more and more competitive and has forced refiners continually to raise the octane rating of their regular and com-petitive grades, and at this writing the same situation exists for premium grades which have possessed relatively high anti-knock properties for some time. Straight-run gasoline produced from paraffin-base or semiparaffin-base crudes has an inherently low anti-knock value, and in order to convert this material to a higher quality it has been found necessary to crack an increasing percentage of the crude oil charge. By completely cracking the heavier portions of the crude, and blending back with the straight-run gasoline, it has been possible to produce an average of 63 to 65 octane number gasoline' on average Mid-Continent crude. This operation carried to the fullest extent does not suffice, however, and the recent and rapid development of the so-called "re-forming unit," has resulted. The straight-run gasoline fraction is cut into two parts: a light, low boiling point gasoline; and a heavy gasoline or naphtha. The latter containing the low anti-knock portions of the gasoline, is sent through a re-forming unit and subjected either to high temperature ,or pressure, or both, which materially increases its octane number. On average Mid-Continent the blend of low boiling point straight-run,

Jan 1, 1932

By Renato G. Bautista, Robert A. Hard

A comparative study has been made of the ex-tractability of several of the transitim metals from thiocyanate sohtions using methyl isobutyl ketone as the organic solvent. Extractions were made of scandium (III), chromium (III), manganese (II), iron (III), and cobalt (II), of which only the scandium , iron, and cobalt were readily extracted. All extractions were made at pH 2 and at 25.5 °C. A series of extraction experiments was made on scandium, iron, and cobalt to determine the effect of thiocyanate cmcentration added as the ammonium and also as the calcium salt. Also determined was the effect of metal ion concentratim and ionic strength on the distribution ratio. Analyses of the organic extracts indicated the scandium and iron were extracted principally in the uncharged trithiocyanate form, while the extractable form of the cobalt contained the cobaltotetrathiocyanate anion. THE chemical separation of metal complexes in solution by solvent extraction has in recent years been developed for large scale separation as well as bench scale work in the laboratory. It has also found increased application in analytical chemistry. Its extension to extractive metallurgy as a unit operation is best illustrated in the recovery of uranium and vanadium from their leached liquor.5-8 The extractability of some thiocyanate systems have been extensively investigated. The rate earths have been separated from one another using butanol as a olvent. Scandium was effectively extracted in ethyl ether using ammonium thiocyanate as the com-plexing agent.'' Similarly, the separation of hafnium from zirconium has been reported using ether""' or hexone13 as the organic solvent. The extractability of various metal thiocyanates in ethyl ether is given by 0ck.l Sharp and Wilkinson15 prepared nickel-free cobalt slats by thiocyanate extraction. The mechanism of extraction of titanium (IV) thiocyanate with methyl isobutyl ketone was determined by elafosse.''" The characterization of cobalt (TI) thiocyanate complex using methyl isobutyl ketone as the solvent at near neutral aqueous solution and the spectrometric studies of the ex-tractable cobalt complex has been made by Hard." It is noteworthy to mention at this point that the fundamental characteristic of ketone (oxonium) solvent extraction is that the extractable species are uncharged ion pairs solvated by the ketone molecules, but probably still partially hydrated.

Jan 1, 1963

By Harry Klemic

Zirconium and hafnium minerals are used industrially both as minerals valuable for their chemical and physical characteristics and as ores of zirconium and hafnium. The principal zirconium-hafnium-bearing minerals, their composition, and their ranges in content of zirconium and hafnium dioxides are listed in Table 1. The supply of zirconium and hafnium is based almost entirely upon the supply of the minerals zircon and baddeleyite. Eudialyte may eventually also be of importance as a source of these elements. Zircon, which generally contains nearly 49% zirconium and between 0.4 and 1.5% hafnium, is the principal industrial mineral of this group. Baddeleyite, a commercially important but less abundant mineral, contains as much as 73% zirconium and 0.4 to 1.7% hafnium. Eudialyte has a wide range in content of these elements, but analyses of material from several localities indicate values of 6 to 11 % zirconium and 0.07 to 0.4% hafnium. Zircon is a mineral consisting principally of zirconium, silicon, and oxygen that crystallizes from magmas during the formation of igneous rocks. Zircon also occurs in veins and in metamorphic rocks. It is in the tetragonal crystal system. It commonly forms as small well-developed prisms having pyramidal terminations but also occurs as irregular-shaped grains. Zircon has a hardness of 7.5 on the Mohs' scale. Its specific gravity is commonly between 4.68 and 4.70 (Dana, 1932), but the specific gravity varies somewhat depending upon com- position and state of alteration. Zircon has no good cleavage directions and is brittle, breaking with a conchoidal fracture. Zircon of the composition ZrSiO, would contain 67.2% Zr02 and 32.8% SiO2. However, in addition to about 1 % of hafnium, minor amounts of thorium, uranium, rare earth elements, yttrium, calcium, magnesium, iron, aluminum, phosphorus, and hydrogen, and trace amounts of other elements are commonly present in the mineral (Frondel, 1957). Radiogenic lead and other daughter products from the radioactive decay of uranium and thorium also accrue in the mineral. Radiation damage to the structure of zircons that contain appreciable amounts of uranium and thorium may alter the internal structure of the crystals to

Jan 1, 1975

By L. C. Uren

Field studies and laboratory research have established the fact that the expulsive force which drives petroleum into wells, from the reservoir sands in which it is stored by nature, is primarly an expression of the energy latent within compressed natural gas dissolved or occluded in, or otherwise associated with the oil. Each barrel of oil produced is forced into the recovery well by the expansive energy of a certain volume of compressed gas, originally stored with the oil in the pores of the reservoir rock; and each cubic foot of gas so produced with the oil and expanded to atmospheric pressure reduces by so much the total natural energy available for oil expulsion. This relationship between the volumes of gas and oil produced has seemed so important that petroleum production technolo-gists have come to regard the "gas-oil ratio," or the "gas factor" as it has been more conveniently termed, as a measure of oil-production efficiency. Different methods of oil recovery and production devices are now Com pared on this basis and estimates of ultimate recovery obtainable through their use are considered by many to be inversely proportional to the values of their respective gas factors. The writer has been among those who have given support to a widcspread movement toward a proper recognition of the significance of the gas factor as a guide in the control of producing oil wells, and does not wish to oppose its more extended application. It seems necessary, how-cvcr, in view of the almost elemental faith with which the principle of the gas factor has been received in many quarters, to point out that it is a most complex factor, and one which cannot be regarded as an absolute index of production efficiency without due regard to other contributing factors by which it is influenced to an important degree. Variables Influencing Gas Factor The mere recording of a low gas factor, obtained through the use of some method or device, does not necessarily imply efficient oil production; and conversely, a high gas factor does not always signify inefficient recov-

Jan 1, 1928

By P. G. Shewmon, W. M. Robertson

The derivative of the surface tension with orientation, ??/??, for copper has been measured over the entire unit triangle. This derivative or torque term was determined from the variation of the dihedral angles at the intersection of twin boundaries and free surfaces. High-temperature anneals in graphite with a hydrogen atmosphere gave torque terms of 0.097 at (111), 0.066 at (100), and 0.0257 at (110). A variation from -36oto +23oC in the dew Point of the H2 had no effect on these values, nor did a change from 99.98 to 99.999 pct Pure copper. The removal of graphite from the system decreased ??/?? slightly. Considering the surface near a low-index plane to be smooth except for occasional steps, the free-energy increment per cm of step is calculated, and it is shown that the observed variation of ??/?? is consistent with a random distribution of steps and an interaction energy between steps. Integration of ??/?? gave the relative values of y at (100), (110), and (111) as comPared to ymax: (Y111/Ymax) =0.974, (Y110/Ymax) =0.996, (y100/Ymax) = 0.983. The ratio of the surface tension of coherent twin boundaries to the surface tension of the free surface was found to be (yT/ys) = 0.027 * 0.011. In a crystalline solid the surface tension y (surface free energy per unit area) depends on the orientation of the surface relative to the crystallographic axes of the crystal. Measurements of this variation of y with surface orientation have been reported for metals only within the last few years. Consider the grain boundary groove shown in Fig. 1. Here the three surfaces are all normal to the plane of the paper, and each has a different surface tension, y1, y2, and y3. If the system is at equilibrium, the total surface free energy must remain unchanged for a slight vertical displacement of the intersection (points A, B, and C are kept fixed). As shown by Herring,' the following equation is obtained:

Jan 1, 1962

By John B. Myers

VERMICULITE is a name used to describe micaceous material that exfoliates when heated. It is hydrated magnesium-aluminum-iron silicate. The chemical composition, color, physical appearance, and degree of exfoliation vary. COMPOSITION, PROPERTIES, AND ORIGIN Vermiculite has the characteristic micaceous structure of basal cleavage and readily splits into thin laminae, which are soft, pliable, and inelastic. The monoclinic crystal faces are often marked by triangular lines at 60° and 120°. Hardness is 1.5; specific gravity, 2.2-2.7; luster pearly to greasy; colors, amber, bronze, reddish brown, dark green, and black. Feel is soapy, particularly when wet. When heated it exfoliates by expanding at right angles to the cleavage into long wormlike pieces (the name vermiculite is from the Latin veamiculari, to breed worms). This important characteristic of expansion is believed to be a mechanical separation of the layers when the contained water is converted into steam. Warping of the unit layers may also contribute to the expansion. The increase in bulk volume of commercially prepared material is 8 to 12 times but individual flakes may increase in size more than this. Pure vermiculite is a distinct mineral and has the structural formula (OH), (Mg,Fe)3 (Si,Al,Fe)4 010.4H20. It rarely occurs in this pure form, but generally as a mixed mineral of varying structure. One explanation is that the mixed material is composed of unit layers of inter-stratified pure vermiculite and biotite. The essential difference between the two is that unit cell structure of vermiculite contains a layer of water molecules whereas the biotite cell contains potassium instead of the water. The water content of the mixed vermiculite is less than that of pure vermiculite but more than that of biotite. Pure biotite does not expand when heated. If the proportion of biotite layers in a vermiculite is too high it will adversely affect the degree of exfoliation. Within a given deposit, the great mass of material may approach a definite com-position with local areas of greater biotite content. It is not uncommon to find also small pockets of pure biotite but these are generally segre-

Jan 1, 1949

By A. W. Doepke

CLIMAX is situated in the heart of the high Rockies at Fremont Pass on the Continental Divide. This setting naturally throws some of the romantic aura of the old mining camps around the town. In its early days it was much like them, even to its air of impermanence. Its founders had faith in the future-as did every adventurer who started a hole in the ground and called it a mine. In those days, however, all available money was expended on the mine, and those who labored on the job had to he content with rugged living arrangements. The visitor at Climax today. however, sees a townsite carefully laid out to enhance the natural' beauty of the surroundings. There are 250 houses and 43 apartments which have been carefully designed by an architect, and missing is the long line of houses of the same type. Every house is of a different design, all being modern in every respect, with haths, running water, electricity, and .sewage disposal. They vary in size from three to six rooms and rent for $5 per room per month. A complete, well-designed water-treatment plant supplies water for domestic purposes.

Jan 1, 1946

By Edmund J. Pryor

DURING the war years restrictions on travel, pressure of work, and the irregular arrival of technical literature from abroad combined to severely isolate Great Britain in a period of intense war expansion of the art and practice of mineral dressing. Many British technicians were fully occupied with the day-to-day problems of improvising substitutes as regular sources of supply failed. and with mastering the strange demands and working conditions of wartime. After a long day spent between ones laboratory and production work, the rest of the waking hours were often filled with fire watching or home guard patrol activities, substituting for a night-shift manager, or "resting" in a dugout while the bombs came down. There was no time for serious study of such technical literature as survived the Atlantic crossing.

Jan 1, 1947

By F. F. Aplan

For the past year, MBD has been engaged in a lively discussion on a name change for the Division. To complicate things, more than one name change has been proposed! There has been much discussion on the subject, as anyone who has attended the Annual MBD Business Meeting or read [jE] knows. The position of many of our members is well known. There is, however, one group that has not been heard from. These are the future members-the present students and those even younger who are yet to elect our profession. As one who has traversed the academic-industrial interface several times, I think I am qualified to speak for this group. Before going further I think it wise to state unequivocally that our Division should adequately represent our profession. The whole profession is just too small to chop into a plethora of pieces: "I'm not a mineral processing engineer, I'm an ore dresser-well, actually, I specialize in comminution, specifically in grinding, mostly in autogeneous grinding-primary autogeneous grinding that is-and my 'thing' is really iron ores, taconites, mind you!" Enough to confuse even those that keep the faith, and certainly we can't build a profession on such narrow pieces. Either an employer can hire a professional who knows the entire profession or he can't. As more and more companies search out opportunities in the mining and metallurgical fields and as environmental considerations bring into question even our technically well proven processes and procedures, there is a greater need than ever be- fore for a well-rounded mineral processing engineer well versed in all of the process possibilities. What is needed is one who can take an ore-or municipal trash for that matter-and produce there from a valuable product by the most appropriate means. It doesn't really matter if this is done physically, chemically or thermally.

Jan 1, 1971

Edward K. Landis, Philadelphia, Pa.: In studying Mr. Thackray's paper it seemed that a critical comparison of the results from different methods therein reported would he of interest. For this purpose Table I. was constructed by grouping all determinations made by the same method, and the probable errors were calculated. In this table all chemists titrating with permanganate (A1, E, F, G and 0 of Mr. Thackray's paper) are classed under "Emmerton;" those titrating with nitric acid (C, J, S and Y) under " Handy; " those re Probable error of result: a, ±0.0008996; b, ±0.000694; c, ±0.00107; d, ±0.00115; e, ±0.000674; f, ±0.000473; g, ±0.003675; h, ±20.0007959; i,0.000.5098; k, ±0.0008303. Probable error of single determination: a, ±0.001989; b, ±0.001547; c, ±0.00214; d, ±0.0023;e, ±0.00116;f, ±0.000818;g, ±0.0019;h, ±0.00224; i, 40.00143; k, ±0.00234. The formula for calculating the probable error is 0.6745, where N (N— 1)' S is the sum of the squares of the differences from the mean and N is the number of determinations.

Jan 1, 1897

By M. C. Udy, P. C. Rosenthal

THE use of minute boron additions to steel has been given considerable attention in recent years. Comparisons made between boron-free and boron-containing heats of otherwise identical analysis have indicated, beyond a doubt, the potent effect of boron for increasing hardenability. The actual hardenability increase has been expressed as a multiplying factor, or in terms of the percentage of other alloying elements boron might replace, The present study presents the results of a systematic survey of. the use of boron as an addition to two types of alloyed steels and as a replacement for various percentages of molybdenum in these steels, Both cast and wrought steels of the two basic compositions were prepared. Molybdenum, because of its scarcity at the time the investigation was started, was selected as the element to be replaced by boron. Attention was also given to the effects of boron on other properties of the steels, particularly their notched-bar toughness, to investigate other advantages or limitations of this element as an alloy addition. EXPERIMENTAL WORK Steels Investigated The two basic compositions used in this survey of boron as a replacement for molybdenum are given in Table I. The cast steels were higher than the wrought steels in silicon content to improve the casting quality. [ ] Each of these base steels, both cast and wrought, was made with molybdenum contents of o, 0.10, 0.20, 0.30, or 0.40 per cent, the total comprising 20 steels. In addition, each of these 20 compositions . was prepared with boron additions in amounts of 0.0015, 0.003, and o,006 per cent as ferroboron; and in amounts of 0.002 and 0.005 per cent as two com¬mercial intensifier alloys, designated alloys A and B. The boron-treated steels totaled 100, and the entire series 120, Test Procedure Each steel was melted as an individual heat in a 50-lb., magnesia-lined induction furnace. Ingot iron scrap or mixtures of ingot iron and steel scrap were used for melting stock. Deoxidation was carried out in the furnace with o.10 per cent aluminum. The aluminum addition was

Jan 1, 1946