Search Documents

By Noel S. Christensen

COBALT is a silvery white metal with a slight bluish cast, strongly resembling nickel in its appearance and properties, notably its resistance to corrosion, although its alloys with other metals differ quite decidedly in their properties from those of nickel. The name cobalt was derived from the German "Kobold" meaning goblin and this came to be applied to the cobalt minerals which, although they resembled ores, did not readily yield metal when smelted by the primitive processes available in the Middle Ages. Cobalt minerals were used as pigments by potters and glass workers before the Christian era. Cobalt blue glass was found in the tombs of the Egyptians and in the ruins of Troy, and many colors used by the ancient Greeks and Romans contained cobalt. The ancients were entirely unaware that the colors they used were caused by cobalt and the metal itself was only isolated about the middle of the eighteenth century by Brandt although the preparation of cobalt compounds had been carried on in a small way ever since the opening of the silver-cobalt deposits at Schneeberg, Germany, in 1470. The metal is fairly hard, with a density when pure of 8.81 in the cast state and 8.92 after working. The commercial grade of cobalt has a density of about 8.75 in the cast state. The atomic weight is 58.97. The Brinell hardness of the pure metal is 124; that of the commercial grade varies from as low as 100 to as high as 138, depend¬ing upon the impurities present. Pure cobalt has a sharp melting point at 1478°C. The tensile strength of the pure metal in the cast condition is said to be higher than that of any other pure metal. Kalmus gives it as 34,400 lb. per sq. in. for cast unannealed metal; the effect of annealing at 850 to 900°C. is to raise the strength slightly. The yield point is close to the ultimate strength and the reduction in area and elongation are both low. Mechanical working raises the tensile strength of pure cobalt rapidly and in the form of wire it will be over 100,000 lb. per sq. in. The presence of small quantities of carbon in the commercial metal raises the tensile strength to as high as 61,000 lb. per sq. in., the reduction in area and elongation being raised at the same time to approximately 20 per cent.

Jan 1, 1933

By H. E. Exner

This article is a critical review of the influence of surface preparation on crack formation at Vickers indentations in the test used by Palmqvist3-7 to evaluate the toughness of cemented carbides. Experimental results are presented which clearly show that grinding introduces compressive surface stresses into the cobalt phase and thus reduces the crack length. The deformed surface layer is removed by polishing and a stress pattern is approached corresponding to that in the bulk material. Cracks of maximum length are characteristic of this stress state. Deformation stresses can be removed by annealing above 800°C. On the basis of these results , sample preparation for the crack length test can be simplified, the accuracy of measurement is improved, and a simple and significani parameter is found to describe crack resistance of cemented carbides. FOLLOWING suggestions by Ammann and Hinniiber,1'2 Palmqvist3-7 developed a method for testing the toughness of cemented carbides using as a measure the sum of crack lengths at the four corners of a Vickers hardness indentation. This method has several advantages over the bend test commonly used in carbide technology: a) specially formed samples are unnecessary; b) sufficient information can be obtained from one sample; c) the scatter is relatively small; d) the range of actual values for commercial cutting alloys is wide. Thus, this test is both cheaper and more precise than the bend test. Nevertheless, Palmqvist's method is not widely used, mainly for two reasons: a) The relationship between crack length and the technological properties of the material (wear and shock resistance) is not clear. b) The crack length is strongly dependent on surface treatment. It is necessary, therefore, that surface preparation be very precise and reproducible, conditions usually hard to obtain. While any other simple mechanical test has this first drawback, the second became crucial in the application of the crack length method as a practical test. The reasons that this drawback could not be eliminated are, in our opinion, misleading and inconsistent interpretations of the influence of surface preparation on the crack length given in literature. In the following, after a short review of previous experimental results the interpretations given by different authors,4?'-11 cf. Table I, are discussed critically and a consistent explanation is presented on the basis of which improvements of the method of crack length testing are proposed. 1) PREVIOUS EXPERIMENTAL RESULTS In his first attempt to use the cracks at Vickers impressions as a quantitative measure of the toughness of cemented carbides, palmqvist3 calculated the work necessary to initiate cracks by the formula: Sk =k.Pk. [I] where k = numerical constant = 6.49, Sk = critical work to initiate cracks (gf cm), Pk = critical load (load necessary to initiate cracks) HV = Vickers hardness (kp per sq mm). The difficulties involved in experimental determination of the critical load were overcome by the observation that a linear relation holds between the applied load and the sum of the crack lengths at the four corners of the indentation. This linear function, given by Eq. [2] below, was confirmed by Dawihl and Alt-meyer9and by our experiments, see Fig. 1: I = a1.P +a2 [2] where 1 = sum of the crack lengths at a Vickers indentation, P = applied load, al, a2 = parameters dependent on the toughness of the alloy and the surface preparation. The critical load, Pk, is now given by a2, which can be obtained by extrapolating the load vs crack length line to zero crack length, see Fig. 1. This simple relationship, Eq. [2], led Palmqvist1,7 to a parameter which was more reproducible and easier to obtain experimentally than the critical work: the work, S300, put into the sample to produce an average crack length of 300 µm per indentation. This parameter is calculated using the formula: where the load, P3oo, giving a crack length of 300 µm, can be taken from the load-crack length plot, Fig. 1,

Jan 1, 1970

By V. V. Clark

WHEN a district is more or less primitive, and a trained mining engineer attempts single- handed to prospect it according to old standards, he generally fails. He has not the ability to live out in the open alone for months at a time and carry on with enthusiasm and determination like the old-time prospector. But the same engineer, placed in an organized group where modern prospecting methods are employed, is immediately put on his mettle and his chances of winning are greatly increased. Marsman Investments, Ltd., with headquarters in Manila, has at the present time, Sept. 4, 1937, six prospecting parties in the Netherland East Indies. Three of these groups are combing their assignments for lode mines, studying structures, developing and reaching out into veins and zones with diamond drills. The other three are searching for placer mines with pans, pits, and Empire drills. I am in charge of one group seeking commercial gold placers on the Island of

Jan 1, 1937

By Robert L. Clayton, Arthur Baker

Two massive sulfide zinc-copper ore bodies are in quartz-sericite schist (probably formed by regional metamorphism of sediments) and andesite of the Precambrian Yavapai Series, on opposite sides of a large rhyolite mass. The Copper Queen ore body is conformable with bedding of its schist host rock, but the Old Dick ore body probably crosscuts the strata. A lens of low-grade mineralization in chlorite schist, associated with the Old Dick ore body, crosscuts through 150 feet of strata. The ore bodies are almost entirely enclosed by premineral faults with less than 150 feet of displacement. The minerals of the ores are pyrite, sphalerite, and chalcopyrite, with minor arsenopyrite and galena and small amounts of intimately associated chlorite, sericite, and calcite. Old Dick sphalerite-chalcopyrite intergrowths have mutual boundaries, and sphalerite grains contain abundant exsolved chalcopyrite. Copper Queen sphalerite-chalcopyrite intergrowths have extremely ragged boundaries, the sphalerite contains no exsolved chalcopyrite, and the ore overall has a schistose texture. The pre-mineral fault on the hanging wall of the Copper Queen ore body has had 100 feet of post-mineral displacement. Wall rocks of the Old Dick ore body locally have been sericitized. Andesite and quartz-sericite schists for at least several hundred feet around both ore bodies have been chloritized erratically and contain traces of copper.

Jan 1, 1968

By Donald B. Gillies

PROBABLY the most critical and difficult period in an engineer's career is that between the completion of his college work and his attainment of professional recognition and accepted status in the industrial world. Upon leaving school the young graduate breaks his immediate ties with his educational institution and in a sense finds himself adrift. At this time in his life a society like our Institute has both the responsibility and the privilege of meeting a vitally important need in his professional life. Some of these young men are Student Associates, in the year after graduation, and some are Junior Members, but all need advice and assistance. In some respects this situation will be accentuated by the war. Not only will thousands of young engineers be mustered out of military service but the process we describe generally as industrial reconversion will make necessary many readjustments in personnel. About two years ago the Institute recognized the opportunity of helping the younger member to help himself by appointing a new standing committee to be known as the Committee on Professional Development of Junior Engineers. Herbert Hoover is Honorary Chairman and it is my privilege to serve as Chairman. The name of the Committee is not entirely satisfactory but it expresses the general objective. The present article is in the nature of a progress report of the work of this Committee.

Jan 1, 1945

By T. Sterry Hunt

Jan 1, 1891

By Blair R. Benner

This paper describes the installation and operation of a Texas Nuclear on-line silica analyzer (NOLA) coupled with a Leeds and Northrup Microtrac particle-size monitor (Microtrac) at U.S. Steel's Minntac taconite concentrator. An automatic sampling system provides the NOLA with samples of final concentrate. After the sample is analyzed for silica by the NOLA, it is pumped to the Microtrac for size and surface area measurement. A sample is analyzed every six minutes, providing the control room with the silica concentration, the percent passing 270, 400, and 500 mesh, and an equivalent Blaine surface area number. When fed a slurry of final concentrate containing between 20 and 70% solids and 5 to 6% silica, the NOLA analysis is within ±0.2% of the wet chemistry silica. The agreement between the Microtrac output and standard screen analyses is ±1.2% at 270 mesh; ±1.5% at 400 mesh, and ±2% at 500 mesh. The poorer disagreement at the finer sizes is mainly due to inaccuracies in screening at 400 and 500 mesh. The agreement between Microtrac surface area a d laboratory Blaine surface area is about 9 ±80 cm 2/g. These instruments provide rapid and reliable feedback information to the concentrator and feed forward information to the agglomerator.

Jan 1, 1984

By Hugh H. Waesche

OF all the military services, the Signal Corps is the most concerned with piezoelectric minerals because of its function as a supply service to the strategic and tactical military forces. Consequently this paper is written from the point of view of one associated with that organization. The Signal Corps is responsible for the research, development, and supply of communications, radar, and components to the using services of the Department of the Army and to some extent the other branches of the National Defense Department. Their work therefore includes the study of the sources, characteristics, and application of quartz and other piezoelectric materials. These materials have become a vital consideration in strategic planning and are essential for efficient tactical operation by all the Armed Forces. The Signal Corps at the beginning of World War II was responsible for both Army Ground and Air Force electronic equipment. Since that time this Army service organization has probably done more in the development of frequency control devices using piezoelectric materials than any other group.

Jan 1, 1949

By Edward W. Parker

I. INTRODUCTION. AT the Seventy-sixth meeting of the Institute, held in New York, N. Y., February, 1899, I presented a, paper on this subject entitled, Coal-Cutting Machinery,' which has become somewhat out of date, in view of the decade's development in this feature of the coal-minim industry. It should be explained that the present paper is limited to the use of mining-machines in bituminous mines. Practically all of the anthracite mined is ?shot from the solid," no undercutting being done. Anthracite-mining is therefore not considered in the statistics or other references. The statistical record as compiled by the United States Geological Survey shows that in 1898, the year preceding the presentation of my former paper, there were 32,413,144 short tons of coal undercut by the use of machines. In 1907 the machine-mined coal-product amounted to 138,547,823 short tons. In sympathy with the general decrease in coal-production during 1908, the output of machine-mined coal decreased to 123,183,334 short tons, but the proportion of machine-mined coal to the total output, nevertheless, showed an increase, from 35.1 per cent in 1907 to 37 per cent in 1908. In 1898 only 19.5 per cent. of the total product was undercut by the use of machines. The number of undercutting-machines in use in the bituminous mines of the United States has increased from 2,622 in 1898 to 11,144 in 1907, and to 11,569 in 1908. The total production of bituminous coal in the United States in 1908 was almost exactly double that of 1898, while the machine- * Published by permission of the Director of the U. S. Geological Survey. 1 Trans.. xxix.. 400 to 4,59 (1899).

Sep 1, 1910

By Gordon S. Duncan

(New York Meeting, February, 1912 THE U. S. Geological Survey, I believe, has almost completed a study of the Harney Peak quadrangle, preliminary to the publication of a report on that, district. As I was engaged for some months on an investigation of the mode of occurrence of the ore-bearing formation in this area, it has seemed to me timely to make public the results of my study, as a contribution to the consideration of this subject. It seems scarcely necessary to describe the locality and general geology of the Black hills of South Dakota, for since 1846 many have contributed information concerning this region, some of the reports bearing such well-known names as those of Walter P. Jenney, Henry Newton, S. F. Emmons, and C. R. Van Hise, while we have only to glance at Bulletin No. 4 of the South Dakota School of Mines, in which Prof. C. C. O'Harra, of that institution, has given us a bibliography of contributions to the geography and geology of the section, to find that other well-known men have studied the district, and have given us the benefit of their researches. The U. S. Geological Survey has made geological maps of nearly the whole of the Black hills, the only quadrangle yet to be completed being, as stated, the Harney Peak district. During the late summer and autnmn of 1910, it was my lot to examine and report. on a considerable area in this neighborhood, which once had been prospected, and in some cases exploited, for tin. This paper gives an account of certain geological phenomena, noted at that time, which greatly influenced my conclnsions. The predominating formation of the district is pre-Cambrian, represented by a highly-cleaved mica-schist, usually very garnetiferous, and sometimes hornblendic. Rising like an island from the surrounding schist is a large mass of granite, known as

Jul 1, 1912

C. Edward Stafford, Chester, Pa.:—Doring all my business life, I have been engaged in the manufacture of Bessemer and open-hearth steels, but, during my long connection with the Shoenberger Steel Co. of Pittsburg, I had some experience in the manufacture of high-grade puddled iron for horseshoes, and in making, by Dr. Otto Wuth's process, extremely pure, low-phosphorus puddled blooms (analyzing from 0.005 to 0.01 per cent. of phosphorus and sulphur), which were melted with low-phosphorus pig-iron in acid open-hearth furnaces, to make extra locomotive fire-box steel. I have also seen the Danks puddlers in operation at different times and places, notably where they were most successful, at the Otis Steel Works, Cleveland, Ohio; then under the management of our friend, Mr. S. T. Wellman. These Danks blooms were made solely for open-hearth melting-stock, to which they were well adapted. (The unavoidable presence of bits of ore-fix imbedded in the mass of the metal always prevents the profitable manufacture of merchant iron from Danks' blooms.) With the experience just described, I was to some degree in position to value fairly the means, methods and results of Mr. Roe's mechanical puddling from the metallurgical or technical and economic points of view, when given an opportunity by Mr. Roe to see his puddling-furnace or machine in operation in Pottstown, Pa. Briefly, the furnace, with water-cooled bottom, is rectangular in plan, about 20 by 8 ft. in the clear, suspended by trunnions at the middle of the long sides, at a height of 17 or 18 ft. above the general level. The oscillation (65" each way from the vertical) is accomplished by geared segments (attached to the downward-projecting side or trunnion-plates) with which engage pinions driven by a reversing engine. The whole section

Jan 1, 1906

By A. M. STROKG

Discussion of the paper of Charles R. Keyes, presented at the Spokane meeting. Bulletin o. 34, October, 1909, pp. 867 to 903. A. M. STRONG, Bishop, Cal: (communication to the Secretary*) The paper of Mr. Keyes gives us the most complete account of the geology of the borax-deposits in the Death Valley region that has yet been published, and is a valuable addition to the geological literature of a very interesting though little-known territory. During the past ten years I have been over much of the northern part of the country described by Mr. Keyes and the region immediately north of it. Mr. Keyes seems to give the impression that Furnace creek is the northern end of these borate-bearing deposits, but such is not the case. Of the seven principal marsh-deposits which for years furnished the greater part of the borax supply in the manner described by him, four are north of the boundary-line as given on his map. The entire territory immediately east of the Sierra Nevada is composed of a series of sinks, each with a well-defined drainage-area.. Of these, Death valley is the deepest, and its drainage-area one of the greatest. The section given in the paper is typical of any line drawn eastward from the Sierra Nevada. At the lowest point of each of these sinks is a marsh, which, in times of heavy rain-fall in the mountains, is converted into a lake. These marshes always contain borax, which is now considered to have been derived from the washing of the Tertiary lake-beds in the surrounding mountains, of which they form a considerable part. Additional territory which I have studied shows that the boundaries given on Mr. Keyes's map should be considerably extended to the north. Just how far these borate-beds extend I am not prepared to say. J. E. Spurr says of them : 1

Feb 1, 1910

By Nath S. Parate

Emphasis on publications related to coal mining subsidence and damages is appropriate at present in view of the energy crisis and increased coal production and public alertness. I have worked in Harrisburg with the state government Public Utilities Commission on energy-fuel matters and issues (Parate, 1978-80). I have participated in the communication on subsidence/ damage reviews and status with the Bureau of Mines Liasion Office (Kebblish, 1978-79). I have done research (Parate, 1965) and published papers (Parate, 1972; Parate, 1967) in Britain on coal mining subsidence and damages around Sheffield-Nottinghamshire coal fields. I have a few comments on the recent paper titled, "Pennsylvania Subsidence Control Guidelines," by C.J. Bise. 1) What is the basis of the empirical formula or guideline, LD _ (0.27 x D) ± 4.6, defining the support area? 2) The particular structure may not be damaged due to vertical uniform displacement caused by mining beneath unless the displacement is differential (King, 1964). 3) The author mentions the limited subsidence research in the US, and quite rightly so. But he fails to quote any work reference by continental investigators except the British or review work by the US. What are the reasons? 4) The author has not mentioned the importance and role of angle of draw for Pennsylvania, Kentucky, or Illinois coal fields. Is there any current research investigation on the relationship between subsidence research investigation, damage, and transference of strains to structures? There have been a number of newspaper reports on subsidence damage in Wilkesbarre and other areas in Pennsylvania. Is the author aware of such instances and traditional attitudes to such issues? Many times government agencies--due to lack of funds, technical expertise, and public policies--are unable or do not find it interesting to keep updates on these issues, as per the author's knowledge and experience with state governments. 5) What is the net effect and role of the D.E.R. Insurance Office on the monitoring, reducing, or controlling subsidence damage, particularly in Pennsylvania?

Jan 1, 1983

By C. M. Fellman

AVAILABLE data for the first nine months of the Year indicate that accident occurrence in metal mining was well on its way to an all-time low for 1939. However, the relatively rapid pickup in mining production in the fall will be likely to boost both accident occurrence and also accident rates. Results of the National Safety Competition for 1938, the fourteenth of its kind conducted by the U. S. Bureau of Mines, were published in August, 1939. W. W. Adams, statistician of the bureau, states that "with 345 mines and quarries competing, more than in any previous year except 1931, the contest revealed low accident rates at many of the enrolled plants and, which is even more remarkable, it revealed 113 mines and quarries at which no lost- time accidents occurred during the con- test year." The National Safety Competition provides a means whereby mines and quarries may engage in active competition to stimulate their safety programs. Companies in the contest can compare their records with those of similar plants operating elsewhere and thereby determine to what extent their safety programs are successful. The Joseph A. Holmes Safety Association gave over 150 awards for safety performance in the mineral industries in 1939 and a remarkable phase of these awards was the considerable number given to individual miners who had worked fifty or more years without sustaining a lost-time accident.

Jan 1, 1940

By AIME AIME

IN ACCORDANCE with the provisions of the Rules of Procedure of the American Engineering Standards Committee, the American Society for Testing, Mate-. on Feb. 15, 1921, submitted for approval by the A. E. S. Committee certain Standard Specifications for Copper, all of which were adopted or in process prior to Jan. 1, 1920, and sent with the standards the following histories of development and statements of use. FOR SOFT OR ANNEALED COPPER WIRE (B3-15) These specifications were originaly adopted by. the American Society for Testing Materials in 1912. They were prepared by a committee of the Society designated as Committee B-1 on Copper Wire. The committee consisted of eleven members; representatives of five manufacturers of -copper wire, of four manufacturers of electrical apparatus, and of two firms of consulting and contracting engineers. The members of the committee were designated by the officials of the companies to act as their representatives in the committee.

Jan 1, 1921

By AIME AIME

A REGULAR meeting of the Executive Board 'of American Engineering Council was held in the Onondaga Hotel, Syracuse, N.. Y., Feb. 14, 1921, with the president, Herbert Hoover, presiding. Reports of committees were presented and acted upon as follows: ENGINEER ON INTERSTATE COMMERCE COMMISSION The second meeting of the Committee was. called because it was represented to the Committee' on Pro¬cedure that the American Society of Civil Engineers, the American Association of Engineers, and the Ameri¬can Institute of Consulting Engineers were anxious to have President-elect Harding appoint an engineer to fill one of the vacancies on the Interstate Commerce Commission. The representative of The American Society of Civil Engineers agreed to endorse the recom¬mendations- of American Engineering Council, and the Committee on Procedure prepared and sent a letter to the President-elect, a - copy of this letter being sent to each member of the Board. No names were suggested. . The appointment of an engineer on the Interstate Commerce Commission was approved and the Board, after approving the action of the Committee 'on Procedure in writing the President-elect, voted that, if requested, the Committee on Procedure submit a list of not less than six names for the appointment of an engineer on the Interstate. Commerce Commission.

Jan 1, 1921

"The mountains of Utah contain one of the largest deposits of high grade bituminous coal in the world. According to the United States Geological Survey, there are 13,130 square miles of land known to contain workable coal, and these extensive fields contain 196,000,000,000 tons of coal. More remarkable than the extent of the coal fields is the thickness of the coal beds. Over three-fourths of the output of coal in Utah is recovered from beds ranging from 8 to 17 feet in thickness, as compared to one-eighth of the output of the entire country from such beds. In 1917, Utah mined one-third of its coal from seams at least 16 feet thick, compared to one-half of one per cent of the total bituminous output of the country from like seams.Coal at Wales, in Sanpete County, and in the vicinity of Coalville, Utah, was, it is reported, the first discovered by white men in the state. Wales claims the distinction of having produced the first coal mined in Utah. Two men, who had been coal miners in Wales, learned of the coal from an old Indian chief who called it ""rock that would burn."" In 1857, the town of Wales was founded and coal mined, and in 1858 some coke was manufactured and hauled by ox team to Salt Lake City. South of Wales is Castle Valley, in Wasatch Plateau field. From 50 to 60 miles of the Old Spanish Trail from Santa Fe, New Mexico, to Monterey, California, lies in Castle Valley. The coal in this field may or may not have been known at the time the trail was used extensively. The first published reference to this coal, however, was made by a party of the Corps of Topographic Engineers in their journal for October 11, 1853.After the completion of the Union Pacific railroad in 1869, mining on a commercial scale was attempted. In 1876 the Utah and Pleasant Valley railroad commenced operations between Scofield, in Carbon county, and Springville, Utah county, and following the year 1878, when the Rio Grande Western railway began construction through the Carbon county field, development increased until in 1900, when large smelters commenced operations in Salt Lake valley and gave coal mining in Utah an impetus that first carried it to an annual output of a million tons. During the past fifteen years many new mines have been opened, and with the construction of the Utah railway, an exclusive coal road, from the properties of the United States Fuel company in Carbon and Emery counties to connect with the Union Pacific system at Provo, the state reached a maximum production of 6,005, l 99 tons in 1920."

Jan 1, 1925

By R. A. Young

Zinc metal production in the operating plants in the United States during 1948 was approximately equal to that of the year 1947, although new developments during the year assure higher output in 1949, if economic conditions are favorable. In the Western plants, the man-power shortage was almost completely overcome and new capacity has been or is in the process of being added to three plants; thus by December of 1948 daily zinc metal production had risen to the highest point since May of 1944 despite strikes in one large primary smelter and in one secondary plant.

Jan 1, 1949

E. Hill, South Norwalk, Conn. (communication to the Secretary*) :—The phenomenon described by Dr. Ledoux, involving an apparently abnormal high temperature in the air-cylinders of compressors, has not been, so far as I know, discussed in technical literature. The common formula for the adiabatic compression of dry air does not account for heat suficient to flash ordinarily decent cylinder-oils, nor do the text-books include in their theoretical statements any quantitative consideration of the effect of leaks in the ideal machines which they contemplate. This lack I have endeavored to supply by preparing, in the form of a circular, for the use of the customers and correspondents of the Norwalk Iron-Works, a brief mathematical

Jan 1, 1904

Jan 1, 1943